Cirrus CS4335-KSZ 8-pin, 24-bit, 96 khz stereo d/a converter Datasheet

Confidential Draft
3/11/08
CS4334/5/8/9
8-Pin, 24-Bit, 96 kHz Stereo D/A Converter
Features
Description
 Complete Stereo DAC System: Interpolation,
The CS4334 family members are complete, stereo digital-to-analog output systems including interpolation,
1-bit D/A conversion and output analog filtering in an
8-pin package. The CS4334/5/8/9 support all major audio data interface formats, and the individual devices
differ only in the supported interface format.
D/A, Output Analog Filtering
 24-Bit Conversion
 96 dB Dynamic Range
The CS4334 family is based on Delta-Sigma modulation, where the modulator output controls the reference
voltage input to an ultra-linear analog low-pass filter.
This architecture allows for infinite adjustment of sample rate between 2 kHz and 100 kHz simply by
changing the master clock frequency.
 -88 dB THD+N
 Low Clock-Jitter Sensitivity
 Single +5 V Power Supply
 Filtered Line-Level Outputs
The CS4334 family contains on-chip digital de-emphasis, operates from a single +5V power supply, and
requires minimal support circuitry. These features are
ideal for set-top boxes, DVD players, SVCD players,
and A/V receivers.
 On-Chip Digital De-emphasis
 Popguard® Technology
 Functionally Compatible with CS4330/31/33
LRCK
SDATA
ORDERING INFORMATION
See “Ordering Information” on page 24
DEM/SCLK
2
AGND
6
VA
7
Serial Input
Interface
De-emphasis
Voltage Reference
Interpolator
∆Σ
Modulator
DAC
Analog
Low-Pass
Filter
8
Interpolator
∆Σ
Modulator
DAC
Analog
Low-Pass
Filter
5
3
1
AOUTL
AOUTR
4
MCLK
http://www.cirrus.com
Copyright © Cirrus Logic, Inc. 2008
(All Rights Reserved)
March '08
DS248F5
Confidential Draft
3/11/08
CS4334/5/8/9
TABLE OF CONTENTS
1. TYPICAL CONNECTION DIAGRAM .................................................................................................... 4
2. CHARACTERISTICS AND SPECIFICATIONS ..................................................................................... 5
SPECIFIED OPERATING CONDITIONS .............................................................................................. 5
ABSOLUTE MAXIMUM RATINGS ........................................................................................................ 5
ANALOG CHARACTERISTICS............................................................................................................. 6
POWER AND THERMAL CHARACTERISTICS ................................................................................... 8
DIGITAL INPUT CHARACTERISTICS .................................................................................................. 9
SWITCHING CHARACTERISTICS ..................................................................................................... 10
3. GENERAL DESCRIPTION ................................................................................................................. 12
3.1 Digital Interpolation Filter .............................................................................................................. 12
3.2 Delta-Sigma Modulator ................................................................................................................. 12
3.3 Switched-Capacitor DAC .............................................................................................................. 12
3.4 Analog Low-Pass Filter ................................................................................................................. 12
4. SYSTEM DESIGN ............................................................................................................................... 13
4.1 Master Clock ................................................................................................................................. 13
4.2 Serial Clock .................................................................................................................................. 13
4.2.1 External Serial Clock Mode ................................................................................................. 13
4.2.2 Internal Serial Clock Mode .................................................................................................. 13
4.3 De-Emphasis ................................................................................................................................ 14
4.4 Initialization and Power-Down ...................................................................................................... 14
4.5 Output Transient Control .............................................................................................................. 14
4.6 Grounding and Power Supply Decoupling .................................................................................... 15
4.7 Analog Output and Filtering .......................................................................................................... 15
4.8 Overall Base-Rate Frequency Response ..................................................................................... 18
4.9 Overall High-Rate Frequency Response ...................................................................................... 19
4.10 Base Rate Mode Performance Plots .......................................................................................... 20
4.11 High Rate Mode Performance Plots ........................................................................................... 21
5. PARAMETER DEFINITIONS ............................................................................................................... 22
6. REFERENCES ..................................................................................................................................... 22
7. PACKAGE DIMENSIONS ................................................................................................................... 23
8. ORDERING INFORMATION ............................................................................................................... 24
9. FUNCTIONAL COMPATIBILITY ......................................................................................................... 24
10. REVISION HISTORY ......................................................................................................................... 24
LIST OF FIGURES
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
2
Recommended Connection Diagram ......................................................................................... 4
Output Test Load ....................................................................................................................... 8
Maximum Loading...................................................................................................................... 9
Power vs. Sample Rate ............................................................................................................. 9
External Serial Mode Input Timing........................................................................................... 11
Internal Serial Mode Input Timing ............................................................................................ 11
Internal Serial Clock Generation ............................................................................................. 11
System Block Diagram............................................................................................................. 12
De-Emphasis Curve (Fs = 44.1kHz) ........................................................................................ 14
CS4334 Data Format (I²S) ....................................................................................................... 15
CS4335 Data Format ............................................................................................................... 15
CS4338 Data Format ............................................................................................................... 16
CS4339 Data Format ............................................................................................................... 16
CS4334/5/8/9 Initialization and Power-Down Sequence ......................................................... 17
Stopband Rejection.................................................................................................................. 18
Transition Band........................................................................................................................ 18
Transition Band........................................................................................................................ 18
DS248F5
Confidential Draft
3/11/08
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
CS4334/5/8/9
Passband Ripple...................................................................................................................... 18
Stopband Rejection.................................................................................................................. 19
Transition Band........................................................................................................................ 19
Transition Band........................................................................................................................ 19
Passband Ripple...................................................................................................................... 19
0 dBFS FFT (BRM) .................................................................................................................. 20
-60 dBFS FFT (BRM).............................................................................................................. 20
Idle Channel Noise FFT (BRM)................................................................................................ 20
Twin Tone IMD FFT (BRM)...................................................................................................... 20
THD+N vs. Amplitude (BRM) ................................................................................................... 20
THD+N vs. Frequency (BRM) .................................................................................................. 20
0 dBFS FFT (HRM).................................................................................................................. 21
-60 dBFS FFT (HRM).............................................................................................................. 21
Idle Channel Noise FFT (HRM) ............................................................................................... 21
Twin Tone IMD FFT (HRM) ..................................................................................................... 21
THD+N vs. Amplitude (HRM)................................................................................................... 21
THD+N vs. Frequency (HRM)................................................................................................. 21
LIST OF TABLES
Table 1. Common Clock Frequencies ...................................................................................................... 13
PIN DESCRIPTIONS
SERIAL DATA INPUT
DE-EMPHASIS / SCLK
LEFT / RIGHT CLOCK
MASTER CLOCK
No.
Pin Name
I/O
1
SDATA
I
2
DEM/SCLK
I
3
LRCK
I
4
MCLK
I
5
6
7
8
AOUTR
AGND
VA
AOUTL
O
I
I
O
DS248F5
SDATA
1
8
AOUTL
ANALOG LEFT CHANNEL OUTPUT
DEM/SCLK
2
7
VA
ANALOG POWER
LRCK
3
6
AGND
ANALOG GROUND
MCLK
4
5
AOUTR
ANALOG RIGHT CHANNEL OUTPUT
Pin Function and Description
Serial Audio Data Input - Two’s complement MSB-first serial data is input on this pin. The data is
clocked into the CS4334/5/8/9 via internal or external SCLK, and the channel is determined by
LRCK.
De-Emphasis/External Serial Clock Input - Used for de-emphasis filter control or external serial
clock input.
Left/Right Clock - Determines which channel is currently being input on the Audio Serial Data
Input pin, SDATA.
Master Clock - Frequency must be 256x, 384x, or 512x the input sample rate in BRM and either
128x or 192x the input sample rate in HRM.
Analog Right Channel Output - Typically 3.5 Vp-p for a full-scale input signal.
Analog Ground - Analog ground reference is 0V.
Analog Power - Analog power supply is nominally +5 V.
Analog Left Channel Output - Typically 3.5 Vp-p for a full-scale input signal.
3
Confidential Draft
3/11/08
CS4334/5/8/9
1. TYPICAL CONNECTION DIAGRAM
+5V
+
7
0.1 µF
1 µF
VA
1
Audio
Data
Processor
2
3
SDATA
3.3 µF
8
DEM /SCLK
AOUTL
LRCK
560 Ω
Left Audio
Output
+
267 k Ω
C
10 k Ω
RL
CS4334
CS4335
CS4338
CS4339
3.3 µF
560 Ω
5
AOUTR
External Clock
4
MCLK
Right Audio
Output
+
267 k Ω
C
10 k Ω
AG ND
C=
RL
R L + 560
4 π Fs(R L560)
6
Figure 1. Recommended Connection Diagram
4
DS248F5
Confidential Draft
3/11/08
CS4334/5/8/9
2. CHARACTERISTICS AND SPECIFICATIONS
(All Min/Max characteristics and specifications are guaranteed over the Specified Operating Conditions. Typical
performance characteristics and specifications are derived from measurements taken at nominal supply voltages
and TA = 25°C.)
SPECIFIED OPERATING CONDITIONS
(AGND = 0V; all voltages with respect to ground.)
Parameters
DC Power Supply
Ambient Operating Temperature (Power Applied)
-KSZ
-DSZ
Symbol
Min
Nom
Max
Units
VA
TA
4.75
-10
-40
5.0
-
5.5
+70
+85
V
°C
°C
ABSOLUTE MAXIMUM RATINGS
(AGND = 0V; all voltages with respect to ground.)
Parameters
DC Power Supply
Input Current, Any Pin Except Supplies
Digital Input Voltage
Ambient Operating Temperature (power applied)
Storage Temperature
Symbol
Min
Max
Units
VA
Iin
VIND
TA
Tstg
-0.3
-0.3
-55
-65
6.0
±10
VA+0.4
125
150
V
mA
V
°C
°C
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation
is not guaranteed at these extremes.
DS248F5
5
Confidential Draft
3/11/08
CS4334/5/8/9
ANALOG CHARACTERISTICS
(Full-Scale Output Sine Wave, 997 Hz; Test load RL = 10 kΩ, CL = 10 pF (see Figure 2). Fs for Base-Rate Mode =
48 kHz, Measurement Bandwidth 10 Hz to 20 kHz, unless otherwise specified; Fs for High-Rate Mode = 96 kHz,
Measurement Bandwidth 10 Hz to 40 kHz, unless otherwise specified.)
Base-Rate Mode
Parameter
Symbol
High-Rate Mode
Min
Typ
Max
Min
Typ
Max
Unit
88
91
86
89
93
96
91
94
-
91
89
90
96
88
94
-
dB
dB
dB
dB
Total Harmonic Distortion + Noise
(Note 1) THD+N
18 to 24-Bit
0 dB
-20 dB
-60 dB
16-Bit
0 dB
-20 dB
-60 dB
-
-88
-73
-33
-86
-71
-31
-83
-68
-28
-81
-66
-26
-
-88
-70
-30
-86
-68
-28
-83
-65
-25
-81
-63
-23
dB
dB
dB
dB
dB
dB
Interchannel Isolation
-
94
-
-
95
-
dB
85
88
83
86
93
96
91
94
-
88
86
90
96
88
94
-
dB
dB
dB
dB
Total Harmonic Distortion + Noise
(Note 1) THD+N
18 to 24-Bit
0 dB
-20 dB
-60 dB
16-Bit
0 dB
-20 dB
-60 dB
-
-88
-73
-33
-86
-71
-31
-82
-65
-25
-70
-63
-23
-
-88
-70
-30
-86
-68
-28
-82
-62
-22
-80
-60
-20
dB
dB
dB
dB
dB
dB
Interchannel Isolation
-
94
-
-
95
-
dB
Dynamic Performance for CS4334/5/8/9-KSZ
Dynamic Range
(Note 1)
18 to 24-Bit
unweighted
A-Weighted
16-Bit
unweighted
A-Weighted
(1 kHz)
Dynamic Performance for CS4334/5/8/9-DSZ
Dynamic Range
(Note 1)
18 to 24-Bit
unweighted
A-Weighted
16-Bit
unweighted
A-Weighted
(1 kHz)
Notes:
1. One-half LSB of triangular PDF dither added to data.
6
DS248F5
Confidential Draft
3/11/08
CS4334/5/8/9
ANALOG CHARACTERISTICS (Continued)
Base-Rate Mode
Parameter
Symbol
Min
High-Rate Mode
Typ
Max
Min
Typ
Max Unit
0
0
-
.4780
.4996
0
0
-
.4650
.4982
Fs
Fs
Fs
-.01
-
+.08
-.05
-
+.2
dB
-
-
±.08
-
-
±.2
dB
.5465
-
-
.5770
-
-
Fs
Combined Digital and On-chip Analog Filter Response (Note 2)
Passband
(Note 3)
to -0.05 dB corner
to -0.1 dB corner
to -3 dB corner
Frequency Response 10 Hz to 20 kHz
Passband Ripple
StopBand
StopBand Attenuation
(Note 4)
50
-
-
55
-
-
dB
-
9/Fs
-
-
4/Fs
-
s
0 - 40 kHz
0 - 20 kHz
-
±0.36/Fs
-
-
±1.39/Fs
±0.23/Fs
-
s
s
Fs = 32 kHz
Fs = 44.1 kHz
Fs = 48 kHz
-
-
+1.5/+0
+.05/-.25
-.2/-.4
Group Delay
tgd
Passband Group Delay Deviation
De-emphasis Error
Parameters
Symbol
(Note 5)
dB
dB
dB
Min
Typ
Max
Units
-
0.1
±5
100
0.4
-
dB
%
ppm/°C
3.25
-
3.5
2.2
3
100
3.75
-
Vpp
VDC
kΩ
pF
DC Accuracy
Interchannel Gain Mismatch
Gain Error
Gain Drift
Analog Output
Full Scale Output Voltage
Quiescent Voltage
Max AC-Load Resistance
Max Load Capacitance
(Note 6)
(Note 6)
VQ
RL
CL
Notes:
2. Filter response is not tested but is guaranteed by design.
3. Response is clock dependent and will scale with Fs. Note that the response plots (Figures 15-22) have
been normalized to Fs and can be de-normalized by multiplying the X-axis scale by Fs.
4. For Base-Rate Mode, the Measurement Bandwidth is 0.5465 Fs to 3 Fs.
For High-Rate Mode, the Measurement Bandwidth is 0.577 Fs to 1.4 Fs.
5. De-emphasis is not available in High-Rate Mode.
6. Refer to Figure 3.
DS248F5
7
Confidential Draft
3/11/08
CS4334/5/8/9
POWER AND THERMAL CHARACTERISTICS
Parameters
Symbol
Min
Typ
Max
Units
IA
IA
-
15
40
19
-
mA
µA
θJA
PSRR
-
75
0.2
110
79
104
-
mW
mW
°C/Watt
dB
Power Supplies
Power Supply Current
normal operation
power-down state
(Note 7)
normal operation
power-down
Power Dissipation
Package Thermal Resistance
Power Supply Rejection Ratio
(1 kHz)
Notes:
7. Refer to Figure 4. Max Power Dissipation is measured at VA=5.5V.
10 µF
V
out
AOUTx
R
L
C
L
AGND
Figure 2. Output Test Load
8
DS248F5
100
70
75
Safe Operating
Region
50
25
M
75
CS4334/5/8/9
BR
125
Power (mW)
Capacitive Load -- C L (pF)
Confidential Draft
3/11/08
65
HR
M
60
55
2.5
3
5
10
15
50
20
30
Resistive Load -- RL (kΩ )
Figure 3. Maximum Loading
40
50
60
70
80
Sample Rate (kHz)
90
100
Figure 4. Power vs. Sample Rate
DIGITAL INPUT CHARACTERISTICS
Parameters
High-Level Input Voltage
Low-Level Input Voltage
Input Leakage Current
Input Capacitance
(Note 8)
Symbol
Min
Typ
Max
Units
VIH
VIL
Iin
2.0
-
8
0.8
±10
-
V
V
µA
pF
Notes:
8. Iin for CS433X LRCK is ±20µA max.
DS248F5
9
Confidential Draft
3/11/08
CS4334/5/8/9
SWITCHING CHARACTERISTICS
Parameters
Symbol
Input Sample Rate
Fs
Min
Typ
Max
Units
2
-
100
kHz
MCLK Pulse Width High
MCLK/LRCK = 512
10
-
1000
ns
MCLK Pulse Width Low
MCLK/LRCK = 512
10
-
1000
ns
MCLK Pulse Width High
MCLK / LRCK = 384 or 192
21
-
1000
ns
MCLK Pulse Width Low
MCLK / LRCK = 384 or 192
21
-
1000
ns
MCLK Pulse Width High
MCLK / LRCK = 256 or 128
31
-
1000
ns
MCLK Pulse Width Low
MCLK / LRCK = 256 or 128
31
-
1000
ns
40
50
60
%
20
-
-
ns
20
External SCLK Mode
LRCK Duty Cycle (External SCLK only)
SCLK Pulse Width Low
tsclkl
SCLK Pulse Width High
tsclkh
-
-
ns
SCLK Period
MCLK / LRCK = 512, 256 or 384
Base-Rate Mode
tsclkw
1
---------------------( 128 )Fs
-
-
ns
SCLK Period
MCLK / LRCK = 128 or 192
High-Rate Mode
tsclkw
1
------------------( 64 )Fs
-
-
ns
SCLK rising to LRCK edge delay
tslrd
20
-
-
ns
SCLK rising to LRCK edge setup time
tslrs
20
-
-
ns
SDATA valid to SCLK rising setup time
tsdlrs
20
-
-
ns
SCLK rising to SDATA hold time
tsdh
20
-
-
ns
-
50
-
%
-
-
ns
-
µs
-
-
ns
-
-
ns
-
-
ns
Internal SCLK Mode
LRCK Duty Cycle (Internal SCLK only)
SCLK Period
(Note 9)
(Note 10)
tsclkw
tsclkr
1
----------------SCLK
-
SCLK rising to LRCK edge
tsclkw
-----------------2
SDATA valid to SCLK rising setup time
SCLK rising to SDATA hold time
MCLK / LRCK = 512, 256 or 128
tsdlrs
tsdh
1
---------------------- + 10
( 512 )Fs
1
---------------------- + 15
( 512 )Fs
tsdh
SCLK rising to SDATA hold time
MCLK / LRCK = 384 or 192
1
---------------------- + 15
( 384 )Fs
Notes:
9. In Internal SCLK Mode, the Duty Cycle must be 50% +/− 1/2 MCLK Period.
10. The SCLK / LRCK ratio may be either 32, 48, or 64. This ratio depends on part type and MCLK/LRCK
ratio. (See figures Figures 10-13)
10
DS248F5
Confidential Draft
3/11/08
CS4334/5/8/9
LRCK
t sclkh
t slrs
t slrd
t sclkl
SCLK
t sdh
t sdlrs
SDATA
Figure 5. External Serial Mode Input Timing
LR C K
t s clkr
S D A TA
t sclkw
t sdlrs
t sdh
*IN TE R N AL S C L K
Figure 6. Internal Serial Mode Input Timing
The SCLK pulses shown are internal to the CS4334/5/8/9.
LRCK
MCLK
1
N
2
N
*INTERNAL SCLK
SDATA
Figure 7. Internal Serial Clock Generation
* The SCLK pulses shown are internal to the CS4334/5/8/9.
N equals MCLK divided by SCLK
DS248F5
11
Confidential Draft
3/11/08
CS4334/5/8/9
3. GENERAL DESCRIPTION
The CS4334 family of devices offers a complete stereo digital-to-analog system including digital interpolation,
fourth-order delta-sigma digital-to-analog conversion, digital de-emphasis and analog filtering, as shown in
Figure 8. This architecture provides a high tolerance to clock jitter.
The primary purpose of using delta-sigma modulation techniques is to avoid the limitations of resistive laser trimmed
digital-to-analog converter architectures by using an inherently linear 1-bit digital-to-analog converter. The advantages of a 1-bit digital-to-analog converter include: ideal differential linearity, no distortion mechanisms due to resistor matching errors and no linearity drift over time and temperature due to variations in resistor values.
The CS4334 family of devices supports two modes of operation. The devices operate in Base Rate Mode (BRM)
when MCLK/LRCK is 256, 384 or 512 and in High Rate Mode (HRM) when MCLK/LRCK is 128 or 192. High Rate
Mode allows input sample rates up to 100 kHz.
3.1
Digital Interpolation Filter
The digital interpolation filter increases the sample rate, Fs, by a factor of 4 and is followed by a 32× digital
sample-and-hold (16× in HRM). This filter eliminates images of the baseband audio signal which exist at
multiples of the input sample rate. The resulting frequency spectrum has images of the input signal at multiples of 4 Fs. These images are easily removed by the on-chip analog low-pass filter and a simple external
analog filter (see Figure 1).
3.2
Delta-Sigma Modulator
The interpolation filter is followed by a fourth order delta-sigma modulator which converts the interpolation
filter output into 1-bit data at a rate of 128 Fs in BRM (or 64 Fs in HRM).
3.3
Switched-Capacitor DAC
The delta-sigma modulator is followed by a digital-to-analog converter which translates the 1-bit data into a
series of charge packets. The magnitude of the charge in each packet is determined by sampling of a voltage reference onto a switched capacitor, where the polarity of each packet is controlled by the 1-bit data.
This technique greatly reduces the sensitivity to clock jitter and provides low-pass filtering of the output.
3.4
Analog Low-Pass Filter
The final signal stage consists of a continuous-time low-pass filter which serves to smooth the output and
attenuate out-of-band noise.
Digital
Input
Interpolator
Delta-Sigma
Modulator
DAC
Analog
Low-Pass
Filter
Analog
Output
Figure 8. System Block Diagram
12
DS248F5
Confidential Draft
3/11/08
CS4334/5/8/9
4. SYSTEM DESIGN
The CS4334 family accepts data at standard audio sample rates including 48, 44.1 and 32 kHz in BRM and 96, 88.2
and 64 kHz in HRM. Audio data is input via the serial data input pin (SDATA). The Left/Right Clock (LRCK) defines
the channel and delineation of data, and the Serial Clock (SCLK) clocks audio data into the input data buffer. The
CS4334/5/8/9 differ in serial data formats as shown in Figures 10-13.
4.1
Master Clock
MCLK must be either 256x, 384x or 512x the desired input sample rate in BRM and either 128x or 192x the
desired input sample rate in HRM. The LRCK frequency is equal to Fs, the frequency at which words for
each channel are input to the device. The MCLK-to-LRCK frequency ratio is detected automatically during
the initialization sequence by counting the number of MCLK transitions during a single LRCK period. Internal
dividers are set to generate the proper clocks. Table 1 illustrates several standard audio sample rates and
the required MCLK and LRCK frequencies. Please note there is no required phase relationship, but MCLK,
LRCK and SCLK must be synchronous.
MCLK (MHz)
LRCK
(kHz)
32
44.1
48
64
88.2
96
HRM
BRM
128x
192x
256x
384x
512x
4.0960 6.1440 8.1920 12.2880 16.3840
5.6448 8.4672 11.2896 16.9344 22.5792
6.1440 9.2160 12.2880 18.4320 24.5760
8.1920 12.2880
11.2896 16.9344
12.2880 18.4320
Table 1. Common Clock Frequencies
4.2
Serial Clock
The serial clock controls the shifting of data into the input data buffers. The CS4334 family supports both
external and internal serial clock generation modes. Refer to Figures 10-13 for data formats.
4.2.1
External Serial Clock Mode
The CS4334 family will enter the External Serial Clock Mode when 16 low to high transitions are detected
on the DEM/SCLK pin during any phase of the LRCK period. When this mode is enabled, the Internal Serial Clock Mode and de-emphasis filter cannot be accessed. The CS4334 family will switch to Internal Serial Clock Mode if no low to high transitions are detected on the DEM/SCLK pin for 2 consecutive frames
of LRCK. Refer to Figure 14.
4.2.2
Internal Serial Clock Mode
In the Internal Serial Clock Mode, the serial clock is internally derived and synchronous with MCLK and
LRCK. The SCLK/LRCK frequency ratio is either 32, 48, or 64 depending upon data format. Operation in
this mode is identical to operation with an external serial clock synchronized with LRCK. This mode allows
access to the digital de-emphasis function. Refer to Figures 10 - 14 for details.
DS248F5
13
Confidential Draft
3/11/08
4.3
CS4334/5/8/9
De-Emphasis
The CS4334 family includes on-chip digital de-emphasis. Figure 9 shows the de-emphasis curve for Fs
equal to 44.1 kHz. The frequency response of the de-emphasis curve will scale proportionally with changes
in sample rate, Fs.
The de-emphasis filter is active (inactive) if the DEM/SCLK pin is low (high) for 5 consecutive falling edges
of LRCK. This function is available only in the internal serial clock mode.
Gain
dB
T1=50 µs
0dB
T2 = 15 µs
-10dB
F1
3.183 kHz
F2
Frequency
10.61 kHz
Figure 9. De-Emphasis Curve (Fs = 44.1kHz)
4.4
Initialization and Power-Down
The Initialization and Power-Down sequence flow chart is shown in Figure 14. The CS4334 family enters
the Power-Down State upon initial power-up. The interpolation filters and delta-sigma modulators are reset,
and the internal voltage reference, one-bit digital-to-analog converters and switched-capacitor low-pass filters are powered down. The device will remain in the Power-Down mode until MCLK and LRCK are present.
Once MCLK and LRCK are detected, MCLK occurrences are counted over one LRCK period to determine
the MCLK/LRCK frequency ratio. Power is then applied to the internal voltage reference. Finally, power is
applied to the D/A converters and switched-capacitor filters, and the analog outputs will ramp to the quiescent
voltage, VQ.
4.5
Output Transient Control
The CS4334 family uses Popguard® technology to minimize the effects of output transients during powerup and power-down. This technique eliminates the audio transients commonly produced by single-ended
single-supply converters when it is implemented with external DC-blocking capacitors connected in series
with the audio outputs. To make best use of this feature, it is necessary to understand its operation.
When the device is initially powered-up, the audio outputs, AOUTL and AOUTR, are clamped to AGND. After a short delay of approximately 1000 sample periods, each output begins to ramp towards its quiescent
voltage, VQ. Approximately 10,000 sample cycles later, the outputs reach VQ and audio output begins. This
gradual voltage ramping allows time for the external DC-blocking capacitor to charge to VQ, effectively
blocking the quiescent DC voltage.
To prevent transients at power-down, the device must first enter its power-down state. This is accomplished
by removing MCLK or LRCK. When this occurs, audio output ceases and the internal output buffers are disconnected from AOUTL and AOUTR. A soft-start current sink is substituted in place of AOUTL and AOUTR
which allows the DC-blocking capacitors to slowly discharge. Once this charge is dissipated, the power to
the device may be turned off, and the system is ready for the next power-on.
To prevent an audio transient at the next power-on, the DC-blocking capacitors must fully discharge before
turning off the power or exiting the power-down state. If full discharge does not occur, a transient will occur
when the audio outputs are initially clamped to AGND. The time that the device must remain in the power-
14
DS248F5
Confidential Draft
3/11/08
CS4334/5/8/9
down state is related to the value of the DC-blocking capacitance. For example, with a 3.3 µF capacitor, the
time that the device must remain in the power-down state will be approximately 0.4 seconds.
4.6
Grounding and Power Supply Decoupling
As with any high resolution converter, the CS4334 family requires careful attention to power supply and
grounding arrangements to optimize performance. Figure 1 shows the recommended power arrangement
with VA connected to a clean +5V supply. For best performance, decoupling capacitors should be located
as close to the device package as possible with the smallest capacitor closest.
4.7
Analog Output and Filtering
The analog filter present in the CS4334 family is a switched-capacitor filter followed by a continuous time
low pass filter. Its response, combined with that of the digital interpolator, is given in Figures 15 - 22.
Le ft C ha n nel
LR C K
R ig h t C ha n nel
SCLK
SDATA
MSB -1 -2 -3 -4 -5
+5 +4 +3 +2 +1 LSB
Internal SCLK Mode
MSB -1 -2 -3 -4
+5 +4 +3 +2 +1 LSB
External SCLK Mode
I²S, 16-Bit data and INT SCLK = 32 Fs if
MCLK/LRCK = 512, 256 or 128
I²S, Up to 24-Bit data and INT SCLK = 48 Fs if
MCLK/LRCK = 384 or 192
I²S, up to 24-Bit Data
Data Valid on Rising Edge of SCLK
Figure 10. CS4334 Data Format (I²S)
Le ft C ha n nel
LR C K
R ig h t C ha n nel
SCLK
SDATA
M SB -1 -2 -3 -4 -5
+5 +4 +3 +2 +1 LS B
Internal SCLK Mode
M SB -1 -2 -3 -4
+5 +4 +3 +2 +1 LS B
External SCLK Mode
Left Justified, up to 24-Bit Data
INT SCLK = 64 Fs if MCLK/LRCK = 512, 256 or 128
INT SCLK = 48 Fs if MCLK/LRCK = 384 or 192
Left Justified, up to 24-Bit Data
Data Valid on Rising Edge of SCLK
Figure 11. CS4335 Data Format
DS248F5
15
Confidential Draft
3/11/08
LR CK
CS4334/5/8/9
R ig ht C h a n ne l
L e ft C h a nn e l
SCLK
SDATA
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
32 clocks
Internal SCLK Mode
External SCLK Mode
Right Justified, 16-Bit Data
INT SCLK = 32 Fs if MCLK/LRCK = 512, 256 or 128
INT SCLK = 48 Fs if MCLK/LRCK = 384 or 192
Right Justified, 16-Bit Data
Data Valid on Rising Edge of SCLK
SCLK Must Have at Least 32 Cycles per LRCK Period
Figure 12. CS4338 Data Format
LR C K
R ig h t C h a n n e l
L e ft C h a n n e l
SCLK
SDATA
1
0
17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
32 clocks
Internal SCLK Mode
External SCLK Mode
Right Justified, 18-Bit Data
INT SCLK = 64 Fs if MCLK/LRCK = 512, 256 or 128
INT SCLK = 48 Fs if MCLK/LRCK = 384 or 192
Right Justified, 18-Bit Data
Data Valid on Rising Edge of SCLK
SCLK Must Have at Least 36 Cycles per LRCK Period
Figure 13. CS4339 Data Format
16
DS248F5
Confidential Draft
3/11/08
CS4334/5/8/9
Figure 14. CS4334/5/8/9 Initialization and Power-Down Sequence
DS248F5
17
Confidential Draft
3/11/08
4.8
18
CS4334/5/8/9
Overall Base-Rate Frequency Response
Figure 15. Stopband Rejection
Figure 16. Transition Band
Figure 17. Transition Band
Figure 18. Passband Ripple
DS248F5
Confidential Draft
3/11/08
4.9
CS4334/5/8/9
Overall High-Rate Frequency Response
Figure 19. Stopband Rejection
Figure 21. Transition Band
DS248F5
Figure 20. Transition Band
Figure 22. Passband Ripple
19
Confidential Draft
3/11/08
4.10
CS4334/5/8/9
Base Rate Mode Performance Plots
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
dBr
A
dBr A
d
B
r
A
-40
-40
-40
-50
-50
-50
-60
-60
-60
dBr
A
dBr A
-40
-40
-40
-50
-50
-50
-60
-60
-60
d
B
r
-70
-70
-70
-80
-80
-80
-90
-90
-90
-70
-70
-70
-80
-80
-80
-90
-90
-90
A
-100
-100
-100
-110
-110
-110
-100
-100
-100
-110
-110
-110
-120
-120
-120
-130
-130
-130
-120
-120
-120
-130
-130
-130
-140
-140
-140
2k
2k
2k
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
-140
-140
-140
20k
20k
20k
20k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
(16k FFT of a 1 kHz input signal)
Figure 23. 0 dBFS FFT (BRM)
Figure 24. -60 dBFS FFT (BRM)
18k
18k
18k
20k
20k
20k
18k
20k
20k
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
-40
-40
-40
-50
-50
-50
-60
-60
-60
-40
-40
-40
A
dBr
dBr A
A
dBr
A
dBr A
-50
-50
-50
d
B
r
-70
-70
-70
-80
-80
-80
-90
-90
-90
A
4k
4k
4k
(16k FFT of a 1 kHz input signal)
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
d
B
r
2k
2k
2k
-60
-60
-60
-70
-70
-70
-80
-80
-80
-90
-90
-90
-100
-100
-110
-110
-110
-100
-1 00
-100
-100
-1 10
-110
-110
-120
-120
-120
-130
-130
-130
-140
-140
-140
-1 20
-120
-120
-1 30
-130
-130
2k
2k
2k
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
20k
20k
20k
-1 40
-140
-140
2k
2k
2k
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12 k
12k
12k
1 4k
14k
14k
16k
16k
16k
20k
18
k
18k
(16k FFT with no input signal)
(16k FFT of intermodulation distortion using 13 kHz and 14 kHz input signals)
Figure 25. Idle Channel Noise FFT (BRM)
Figure 26. Twin Tone IMD FFT (BRM)
-60
-60
+0
+0
+0
-10
-10
-10
-20
-20
-20
-70
-70
-30
-30
-30
-40
-40
-40
-80
-80
A
dBr
dBrAA
dBr A
d
B
r
d
B
r
A
-90
-90
-50
-50
-50
-60
-60
-60
-70
-70
-70
-80
-80
-80
-100
-100
-90
-90
-90
-100
-100
-100
-110
-110
-60
-60
-50
-50
-40
-40
-30
-30
-20
-20
-10
-10
+0
+0
dBFS
dBFS
-110
-110
-110
20
20
20
50
50
50
100
100
100
200
200
200
500
500
500
Hz
Hz
Hz
1k
1k
1k
2k
2k
2k
5k
5k
5k
10k
10k
10k
20k
20k
20k
(THD+N plots measured using a 1kHz 24-bit dithered input signal)
(THD+N plots measured using a 1kHz 24-bit dithered input signal)
Figure 27. THD+N vs. Amplitude (BRM)
Figure 28. THD+N vs. Frequency (BRM)
All measurements were taken from the CDB4334 evaluation board using the Audio Precision Dual Domain
System Two Cascade.
20
DS248F5
Confidential Draft
3/11/08
4.11
CS4334/5/8/9
High Rate Mode Performance Plots
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
-40
-40
-40
-50
-50
-50
-60
-60
-60
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
dBr
A
dBr A
dBr
A
dBr A
d
B
r
d
B
r
-70
-70
-70
-80
-80
-80
-90
-90
-90
A
-40
-40
-40
-50
-50
-50
-60
-60
-60
A
-70
-70
-70
-80
-80
-80
-90
-90
-90
-100
-100
-100
-110
-110
-110
-100
-100
-100
-110
-110
-110
-120
-120
-120
-130
-130
-130
-120
-120
-120
-130
-130
-130
-140
-140
-140
2k
2k
2k
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
-140
-140
-140
20k
20k
20k
2k
2k
2k
4k
4k
4k
6k
6k
6k
14k
14k
14k
16k
16k
16k
18k
18k
18k
Figure 29. 0 dBFS FFT (HRM)
Figure 30. -60 dBFS FFT (HRM)
+0
+0
+0
-10
-10
-10
-20
-20
-20
-30
-30
-30
+0
+0
+0
-10
-10
-10
-40
-40
-40
-50
-50
-50
-60
-60
-60
-40
-40
-40
D -A C C IF IMD vs A MP L ITUD E
20k
20k
20k
0 8 /0 5 /9 9 1 1 :1 1 :3 6
-20
-20
-20
-30
-30
-30
dBr
A
dBr A
-50
-50
-50
d
B
r
-70
-70
-70
-80
-80
-80
-90
-90
-90
-60
-60
-60
-70
-70
-70
-80
-80
-80
A
-90
-90
-90
-100
-100
-100
-110
-110
-110
-100
-100
-100
-110
-110
-110
-120
-120
-120
-130
-130
-130
-140
-140
-140
12k
12k
12k
(16k FFT of a 1 kHz input signal)
dBr
A
dBr A
A
10k
10k
10k
Hz
Hz
Hz
(16k FFT of a 1 kHz input signal)
A ud io P re c is io n
d
B
r
8k
8k
8k
-120
-120
-120
-130
-130
-130
2k
2k
4k
4k
4k
2k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
Hz
Hz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
-140
-140
-140
20k
20k
20k
2k
2k
2k
4k
4k
4k
6k
6k
6k
8k
8k
8k
10k
10k
10k
Hz
HzHz
12k
12k
12k
14k
14k
14k
16k
16k
16k
18k
18k
18k
20k
20k
20k
(16k FFT with no input signal)
(16k FFT of intermodulation distortion using 13 kHz and 14 kHz input signals)
Figure 31. Idle Channel Noise FFT (HRM)
Figure 32. Twin Tone IMD FFT (HRM)
-60
-60
+0
+0
-10
-10
-10
-20
-20
-20
-70
-70
-30
-30
-30
-80
A
-90
-90
d
B
r
dBr A
d
B
r
-40
-40
-40
dBrdBrAA
-80
-50
-50
-50
-60
-60
-60
A
-70
-70
-70
-80
-80
-80
-100
-100
-90
-90
-90
-100
-100
-100
-110
-110
-60
-60
-50
-50
-40
-40
-30
-30
-20
-20
-10
-10
+0
+0
dBFS
dBFS
-110
-110
-110
20
20
20
50
50
100
100
100
200
200
500
500
Hz
Hz
Hz
1k
1k
2k
2k
5k
5k
10k
10k
20k
20k
20k
(THD+N plots measured using a 1kHz 24-bit dithered input signal)
(THD+N plots measured using a 1kHz 24-bit dithered input signal)
Figure 33. THD+N vs. Amplitude (HRM)
Figure 34. THD+N vs. Frequency (HRM)
All measurements were taken from the CDB4334 evaluation board using the Audio Precision Dual Domain
System Two Cascade.
DS248F5
21
Confidential Draft
3/11/08
CS4334/5/8/9
5. PARAMETER DEFINITIONS
Total Harmonic Distortion + Noise (THD+N)
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
bandwidth (typically 10Hz to 20kHz), including distortion components. Expressed in decibels.
Dynamic Range
The ratio of the full scale rms value of the signal to the rms sum of all other spectral components over the
specified bandwidth. Dynamic range is a signal-to-noise measurement over the specified bandwidth made
with a -60 dBFS signal. 60 dB is then added to the resulting measurement to refer the measurement to full
scale. This technique ensures that the distortion components are below the noise level and do not effect the
measurement. This measurement technique has been accepted by the Audio Engineering Society, AES171991, and the Electronic Industries Association of Japan, EIAJ CP-307.
Interchannel Isolation
A measure of crosstalk between the left and right channels. Measured for each channel at the converter's
output with all zeros to the input under test and a full-scale signal applied to the other channel. Units in decibels.
Interchannel Gain Mismatch
The gain difference between left and right channels. Units in decibels.
Gain Error
The deviation from the nominal full-scale analog output for a full-scale digital input.
Gain Drift
The change in gain value with temperature. Units in ppm/°C.
6. REFERENCES
1. "How to Achieve Optimum Performance from Delta-Sigma A/D & D/A Converters" by Steven Harris. Paper
presented at the 93rd Convention of the Audio Engineering Society, October 1992.
2. CDB4334/5/8/9 Evaluation Board Datasheet
22
DS248F5
Confidential Draft
3/11/08
CS4334/5/8/9
7. PACKAGE DIMENSIONS
8L SOIC (150 MIL BODY) PACKAGE DRAWING
E
H
1
b
c
D
SEATING
PLANE
∝
A
L
e
A1
INCHES
DIM
A
A1
b
c
D
E
e
H
L
∝
MIN
0.053
0.004
0.013
0.007
0.189
0.150
0.040
0.228
0.016
0°
MAX
0.069
0.010
0.020
0.010
0.197
0.157
0.060
0.244
0.050
8°
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.33
0.51
0.19
0.25
4.80
5.00
3.80
4.00
1.02
1.52
5.80
6.20
0.40
1.27
0°
8°
JEDEC # : MS-012
DS248F5
23
Confidential Draft
3/11/08
CS4334/5/8/9
8. ORDERING INFORMATION
Temperature
Package
CS4334-KSZ
CS4335-KSZ
CS4338-KSZ
CS4339-KSZ
Model
-10 to +70 °C
-10 to +70 °C
-10 to +70 °C
-10 to +70 °C
8-pin Plastic SOIC, lead free
8-pin Plastic SOIC, lead free
8-pin Plastic SOIC, lead free
8-pin Plastic SOIC, lead free
16 to 24-bit, I²S
16 to 24-bit, left justified
16-bit, right justified
18-bit, right justified, 32 Fs Internal SCLK mode
Serial Interface
CS4334-DSZ
CS4335-DSZ
CS4338-DSZ
CS4339-DSZ
-40 to +85 °C
-40 to +85 °C
-40 to +85 °C
-40 to +85 °C
8-pin Plastic SOIC, lead free
8-pin Plastic SOIC, lead free
8-pin Plastic SOIC, lead free
8-pin Plastic SOIC, lead free
16 to 24-bit, I²S
16 to 24-bit, left justified
16-bit, right justified
18-bit, right justified, 32 Fs Internal SCLK mode
9. FUNCTIONAL COMPATIBILITY
CS4330-KS ⇒ CS4339-KSZ
CS4331-KS ⇒ CS4334-KSZ
CS4333-KS ⇒ CS4338-KSZ
CS4330-BS ⇒ CS4339-DSZ
CS4331-BS ⇒ CS4334-DSZ
CS4333-BS ⇒ CS4338-DSZ
10.REVISION HISTORY
Revision
Changes
F3
Removed CS4335-BS and CS4339-BS from the Ordering Information section.
F4
Removed CS4334-BS & CS4349-BS and updated all other packages to lead-free. Functional compatibility
was updated to reflect that of the new lead-free packages.
F5
Corrected “B” to “b” and “C” to “c” to match drawing in “Package Dimensions” on page 23
Updated legal text
Contacting Cirrus Logic Support
For all product questions and inquiries, contact a Cirrus Logic Sales Representative.
To find the one nearest you, go to www.cirrus.com.
IMPORTANT NOTICE
Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject
to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant
information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale
supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus
for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third
parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights,
copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent
does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE
IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK AND
CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR
CUSTOMER’S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO
FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS’ FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES.
Cirrus Logic, Cirrus, the Cirrus Logic logo designs and Popguard are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be
trademarks or service marks of their respective owners.
24
DS248F5
Similar pages