DATASHEET ISL62773A FN8410 Rev 1.00 November 19, 2015 Multiphase PWM Regulator for AMD Fusion™ Mobile CPUs Using SVI 2.0 The ISL62773A is fully compliant with AMD Fusion™ SVI 2.0 and provides a complete solution for microprocessor and graphics processor core power. The ISL62773A controller supports two Voltage Regulators (VRs) with three integrated gate drivers and two optional external drivers for maximum flexibility. The Core VR can be configured for 3-, 2-, or 1-phase operation while the Northbridge VR supports 2- or 1-phase configurations. The two VRs share a serial control bus to communicate with the AMD CPU and achieve lower cost and smaller board area compared with two-chip solutions. The PWM modulator is based on Intersil’s Robust Ripple Regulator R3™ Technology. Compared to traditional modulators, the R3™ modulator can automatically change switching frequency for faster transient settling time during load transients and improved light load efficiency. The ISL62773A has several other key features. Both outputs support DCR current sensing with single NTC thermistor for DCR temperature compensation or accurate resistor current sensing. Both outputs utilize remote voltage sense, adjustable switching frequency, OC protection and power-good. Features • Supports AMD SVI 2.0 serial data bus interface - Serial VID clock frequency range 100kHz to 25MHz • Dual output controller with integrated drivers - Two dedicated core drivers - One programmable driver for either Core or Northbridge • Precision voltage regulation - 0.5% system accuracy over-temperature - 0.5V to 1.55V in 6.25mV steps - Enhanced load line accuracy • Supports multiple current sensing methods - Lossless inductor DCR current sensing - Precision resistor current sensing • Programmable 1-, 2- or 3-phase for the core output and 1- or 2-phase for the Northbridge output • Adaptive body diode conduction time reduction • Superior noise immunity and transient response Applications • Output current and voltage telemetry • AMD Fusion CPU/GPU core power • Differential remote voltage sensing • Notebook computers • High efficiency across entire load range • Programmable slew rate • Programmable VID offset and droop on both outputs • Programmable switching frequency for both outputs • Excellent dynamic current balance between phases • Protection: OCP/WOC, OVP, PGOOD and thermal monitor • Small footprint 48 Ld 6x6 QFN package - Pb-free (RoHS compliant) Core Performance 100 1.12 90 1.10 VIN = 8V 70 1.08 VIN = 12V 60 VOUT (A) EFFICIENCY (%) 80 VIN = 19V 50 40 30 VIN = 8V 1.04 VIN = 12V 1.02 1.00 20 10 0 0 1.06 5 10 15 20 25 30 35 IOUT (A) 40 FIGURE 1. EFFICIENCY vs LOAD FN8410 Rev 1.00 November 19, 2015 45 50 VIN = 19V 0.98 VOUT CORE = 1.1V 55 0.96 VOUT CORE = 1.1V 0 5 10 15 20 25 30 35 IOUT (A) 40 45 50 55 FIGURE 2. VOUT vs LOAD Page 1 of 37 ISL62773A Table of Contents Simplified Application Circuit with 3 Internal Drivers Used for Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Simplified Application Circuit for Mid-Power CPUs [2+1 Configuration] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Simplified Application Circuit for Low Power CPUs [1+1 Configuration] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Pin Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . .11 Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Recommended Operating Conditions . . . . . . . . . . . . . . . . .11 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Gate Driver Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . .13 Theory of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Multiphase R3™ Modulator . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Diode Emulation and Period Stretching . . . . . . . . . . . . . . . . . 15 Channel Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Start-Up Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Voltage Regulation and Load Line Implementation . . . . . . . 16 Differential Sensing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Phase Current Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Dynamic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 FB2 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Adaptive Body Diode Conduction Time Reduction . . . . . . . . 20 Resistor Configuration Options. . . . . . . . . . . . . . . . . . . . . . .20 VR Offset Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Floating DriverX AND PWM_Y Configuration . . . . . . . . . . . . . 21 VID-on-the-Fly Slew Rate Selection . . . . . . . . . . . . . . . . . . . . . 21 CCM Switching Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 FN8410 Rev 1.00 November 19, 2015 AMD Serial VID Interface 2.0 . . . . . . . . . . . . . . . . . . . . . . . . Pre-PWROK Metal VID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SVI Interface Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VID-on-the-Fly Transition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SVI Data Communication Protocol . . . . . . . . . . . . . . . . . . . . . SVI Bus Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dynamic Load Line Slope Trim . . . . . . . . . . . . . . . . . . . . . . . . Dynamic Offset Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 22 22 22 23 25 25 25 26 Telemetry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Protection Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overcurrent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Current-Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Undervoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overvoltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Monitor [NTC, NTC_NB]. . . . . . . . . . . . . . . . . . . . . . . Fault Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interface Pin Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 26 27 27 27 27 28 28 Key Component Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . Inductor DCR Current-Sensing Network . . . . . . . . . . . . . . . . Resistor Current-Sensing Network . . . . . . . . . . . . . . . . . . . . . Overcurrent Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Load Line Slope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compensator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Current Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal Monitor Component Selection . . . . . . . . . . . . . . . . . Bootstrap Capacitor Selection . . . . . . . . . . . . . . . . . . . . . . . . Optional FCCM_NB Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . 28 28 30 30 31 31 32 32 33 33 Layout Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 PCB Layout Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 About Intersil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Package Outline Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Page 2 of 37 ISL62773A NB_PH1 ISEN1_NB NB_PH2 ISEN2_NB Ri VNB1 Cn VNB2 VDDP ENABLE VDD VIN Simplified Application Circuit for High Power CPU Core VIN BOOTX UGATEX PHASEX LGATEX ISUMN_NB NTC NB_PH1 VNB1 VNB FCCM_NB ISUMP_NB VIN PWM2_NB ISL6208 NB_PH1 NB_PH2 NB_PH2 COMP_NB VNB2 IMON_NB * FB_NB * *OPTIONAL NTC_NB VR_HOT_L VSEN_NB VNB_SENSE THERMAL INDICATOR IMON PWROK NTC VIN SVT µP SVD VDDIO COMP PWM_Y * PH3 ISL62773A FB2 * ISL6208 SVC BOOT2 FB VIN UGATE2 *OPTIONAL VSEN VCORE PHASE2 VCORE_SENSE RTN LGATE2 PH1 ISEN1 PH2 ISEN2 PH3 ISEN3 BOOT1 VO2 VIN PGOOD PHASE1 LGATE1 PH1 VO1 PH3 PH1 PH2 ISUMP PGOOD_NB VO3 NTC GND PAD ISUMN Cn PH2 UGATE1 Ri VO1 VO2 VO3 FIGURE 3. TYPICAL APPLICATION CIRCUIT USING INDUCTOR DCR SENSING FN8410 Rev 1.00 November 19, 2015 Page 3 of 37 ISL62773A Simplified Application Circuit with 3 Internal Drivers Used for Core NB_PH1 ISEN1_NB NB_PH2 ISEN2_NB Ri VNB1 VNB2 Cn PWM_Y ISL6208 VDDP ENABLE VIN VDD VIN VNB NB_PH1 ISUMN_NB VNB1 FCCM_NB NTC VIN PWM2_NB ISL6208 ISUMP_NB NB_PH1 NB_PH2 NB_PH2 VNB2 COMP_NB IMON_NB * FB_NB * *OPTIONAL NTC_NB VR_HOT_L VSEN_NB VNB_SENSE THERMAL INDICATOR IMON PWROK NTC SVT µP SVD BOOTX SVC VIN UGATEX VDDIO PHASEX LGATEX COMP PH3 V03 ISL62773A FB2 * FB * BOOT2 *OPTIONAL VIN VSEN UGATE2 VCORE_SENSE RTN VCORE PHASE2 PH1 ISEN1 PH2 ISEN2 PH3 ISEN3 Cn VO3 ISUMN NTC VO2 VIN PHASE1 LGATE1 PH1 VO1 PH3 PH1 PH2 ISUMP PH2 UGATE1 GND PAD VO2 PGOOD VO1 BOOT1 PGOOD_NB Ri LGATE2 FIGURE 4. TYPICAL APPLICATION CIRCUIT USING INDUCTOR DCR SENSING FN8410 Rev 1.00 November 19, 2015 Page 4 of 37 ISL62773A Simplified Application Circuit for Mid-Power CPUs [2+1 Configuration] VDDP PWM_Y ISEN1_NB +5V ISEN2_NB Ri NBN VNB ISL6208 10kΩ* ENABLE VIN * Resistor required or ISEN1_NB will pull HIGH if left open and disable Channel 1. VDD VIN ISUMN_NB NBP NBN VP2 VN2 FCCM_NB NTC Cn ISUMP_NB NBP PWM2_NB OPEN IMON_NB COMP_NB NTC_NB * FB_NB * *OPTIONAL VSEN_NB VNB_SENSE PWROK SVT µP BOOTX OPEN UGATEX OPEN PHASEX OPEN LGATEX OPEN SVD SVC VR_HOT_L THERMAL INDICATOR VDDIO IMON COMP ISL62773A FB2 * BOOT2 FB * NTC VIN UGATE2 *OPTIONAL VSEN PHASE2 VCORE_SENSE RTN LGATE2 VP1 ISEN1 VP2 ISEN2 +5V BOOT1 ISEN3 PGOOD PHASE1 LGATE1 VP1 VN1 VP1 VP2 ISUMP PGOOD_NB NTC GND PAD ISUMN Cn VIN UGATE1 Ri VN1 VN2 VCORE FIGURE 5. TYPICAL APPLICATION CIRCUIT USING RESISTOR SENSING FN8410 Rev 1.00 November 19, 2015 Page 5 of 37 ISL62773A 10kΩ* VDDP ENABLE VIN * Resistor required or ISEN1_NB will pull HIGH if left open and disable Channel 1. VDD Simplified Application Circuit for Low Power CPUs [1+1 Configuration] ISEN1_NB UGATEX ISEN2_NB +5V Ri VNB1 VNB PHASEX ISUMN_NB LGATEX NTC Cn VIN BOOTX NB_PH1 VNB1 ISUMP_NB NB_PH1 FCCM_NB PWM2_NB OPEN COMP_NB * IMON_NB FB_NB * *OPTIONAL NTC_NB VSEN_NB VNB_SENSE VR_HOT NTC PWROK SVT µP THERMAL INDICATOR IMON SVD SVC VDDIO * Resistor required or ISEN1 will pull HIGH if left open and disable Channel 1. 10kΩ* ISEN1 +5V ISEN2 +5V ISEN3 ISL62773A PWM_Y OPEN BOOT2 OPEN UGATE2 OPEN PHASE2 OPEN LGATE2 OPEN COMP OPEN * FB2 BOOT1 FB * VIN UGATE1 *OPTIONAL VSEN VCORE_SENSE RTN Cn ISUMN NTC ISUMP PH1 VO1 PGOOD VO1 GND PAD Ri PGOOD_NB LGATE1 PH1 VCORE PHASE1 FIGURE 6. TYPICAL APPLICATION CIRCUIT USING INDUCTOR DCR SENSING FN8410 Rev 1.00 November 19, 2015 Page 6 of 37 ISL62773A Block Diagram VSEN CORE_I COMP_NB NB_I IMON CURRENT A/D IMON_NB + + RTN + _ FB_NB E/A IDROOP_NB ISUMP_NB + ISUMN_NB _ ISEN1_NB CURRENT SENSE VDD PGOOD_NB OC FAULT CURRENT BALANCING ISEN2_NB PWM2_NB VR2 MODULATOR IBAL FAULT OV FAULT NB_V NTC_NB T_MONITOR TEMP MONITOR NTC VOLTAGE A/D FLOATING DRIVER AND PWM CONFIG LOGIC VR_HOT_L OFFSET FREQ SLEWRATE CONFIG BOOTX DRIVER UGATEX PHASEX PROG DRIVER LGATEX IDROOP_NB ENABLE A/D IDROOP D/A DAC2 DAC1 PWROK DIGITAL INTERFACE SVC PWM_Y VCCP CORE_I SVD BOOT2 NB_I TELEMETRY SVT CORE_V NB_V DRIVER VDDIO UGATE2 PHASE2 COMP VSEN + + RTN FB _ FB2 CIRCUIT + ISUMN _ E/A DRIVER LGATE2 BOOT1 IDROOP FB2 ISUMP VR1 MODULATOR + CURRENT SENSE DRIVER VOLTAGE A/D UGATE1 PHASE1 CORE_V ISEN3 ISEN2 DRIVER CURRENT BALANCING OC FAULT ISEN1 LGATE1 PGOOD IBAL FAULT OV FAULT GND FIGURE 7. BLOCK DIAGRAM FN8410 Rev 1.00 November 19, 2015 Page 7 of 37 ISL62773A Pin Configuration UGATEX LGATEX PHASEX PWM2_NB FCCM_NB PGOOD_NB COMP_NB VSEN_NB FB_NB ISUMP_NB ISUMN_NB ISEN1_NB ISL62773A (48 LD QFN) TOP VIEW 48 47 46 45 44 43 42 41 40 39 38 37 ISEN2_NB 1 36 BOOTX NTC_NB 2 35 VIN IMON_NB 3 34 BOOT2 SVC 4 33 UGATE2 VR_HOT_L 5 SVD 6 GND VDDIO 7 (BOTTOM PAD) 32 PHASE2 31 LGATE2 30 VDDP 23 24 PGOOD BOOT1 COMP 21 22 18 VSEN RTN FB2 FB 20 17 19 16 ISUMP 37 ISUMN 25 UGATE1 15 26 PHASE1 NTC 12 ISEN1 27 LGATE1 IMON 11 14 28 PWM_Y PWROK 10 13 29 VDD ISEN2 8 9 ISEN3 SVT ENABLE Pin Descriptions PIN NUMBER SYMBOL 1 ISEN2_NB 2 NTC_NB 3 IMON_NB 4 SVC 5 VR_HOT_L 6 SVD 7 VDDIO VDDIO is the processor memory interface power rail and this pin serves as the reference to the controller IC for this processor I/O signal level. 8 SVT Serial VID Telemetry (SVT) data line input to the CPU from the controller IC. Telemetry and VID-on-the-fly complete signal provided from this pin. 9 ENABLE Enable input. A high level logic on this pin enables both VRs. 10 PWROK System power-good input. When this pin is high, the SVI 2 interface is active and the I2C protocol is running. While this pin is low, the SVC and SVD input states determine the pre-PWROK metal VID. This pin must be low prior to the ISL62773A PGOOD output going high per the AMD SVI 2.0 Controller Guidelines. 11 IMON Core output current monitor. A current proportional to the Core VR output current is sourced from this pin. 12 NTC 13 ISEN3 ISEN3 is the individual current sensing for Channel 3. When ISEN3 is pulled to +5V, the controller disables Channel 3, and the Core VR runs in two-phase mode. 14 ISEN2 Individual current sensing for Channel 2 of the Core VR. When ISEN2 is pulled to +5V, the controller disables Channel 2 and the Core VR runs in single-phase mode. FN8410 Rev 1.00 November 19, 2015 DESCRIPTION Individual current sensing for Channel 2 of the Northbridge VR. When ISEN2_NB is pulled to +5V, the controller will disable Channel 2 and the Northbridge VR will run single-phase. Thermistor input to VR_HOT_L circuit to monitor Northbridge VR temperature. Northbridge output current monitor. A current proportional to the Northbridge VR output current is sourced from this pin. Serial VID clock input from the CPU processor master device. Thermal indicator signal to AMD CPU. Thermal overload open-drain output indicator active LOW. Serial VID data bidirectional signal from the CPU processor master device to the VR. Thermistor input to VR_HOT_L circuit to monitor Core VR temperature. Page 8 of 37 ISL62773A Pin Descriptions (Continued) PIN NUMBER SYMBOL DESCRIPTION 15 ISEN1 Individual current sensing for Channel 1 of the Core VR. If ISEN2 is tied to +5V, this pin cannot be left open and must be tied to GND with a 10kΩ resistor. If ISEN1 is tied to +5V, the core portion of the IC is shut down. 16 ISUMP Noninverting input of the transconductance amplifier for current monitor and load line of core output. 17 ISUMN Inverting input of the transconductance amplifier for current monitor and load line of core output. 18 VSEN Output voltage sense pin for the core controller. Connect to the +sense pin of the microprocessor die. 19 RTN Output voltage sense return pin for both Core VR and Northbridge VR. Connect to the -sense pin of the microprocessor die. 20 FB2 There is a switch between the FB2 pin and the FB pin. The switch is on in 2-phase or 3-phase mode and is off in 1-phase mode. The components connecting to FB2 are used to adjust the compensation in 1-phase mode of the Core VR to achieve optimum performance. 21 FB Output voltage feedback to the inverting input of the core controller error amplifier. 22 COMP Core controller error amplifier output. A resistor from COMP to GND sets the Core VR offset voltage. 23 PGOOD Open-drain output to indicate the core portion of the IC is ready to supply regulated voltage. Pull-up externally to VDD or 3.3V through a resistor. 24 BOOT1 Connect an MLCC capacitor across the BOOT1 and the PHASE1 pins. The boot capacitor is charged, through an internal boot diode connected from the VDDP pin to the BOOT1 pin, each time the PHASE1 pin drops below VDDP minus the voltage dropped across the internal boot diode. 25 UGATE1 Output of the Phase 1 high-side MOSFET gate driver of the Core VR. Connect the UGATE1 pin to the gate of the Phase 1 high-side MOSFET(s). 26 PHASE1 Current return path for the Phase 1 high-side MOSFET gate driver of VR1. Connect the PHASE1 pin to the node consisting of the high-side MOSFET source, the low-side MOSFET drain and the output inductor of Phase 1. 27 LGATE1 Output of the Phase 1 low-side MOSFET gate driver of the Core VR. Connect the LGATE1 pin to the gate of the Phase 1 low-side MOSFET(s). 28 PWM_Y Floating PWM output used for either Channel 3 of the Core VR or Channel 1 of the Northbridge VR depending on the FCCM_NB resistor connected between FCCM_NB and GND. 29 VDD 30 VDDP Input voltage bias for the internal gate drivers. Connect +5V to the VDDP pin. Decouple with at least 1µF of capacitance to GND. A high quality, X7R dielectric MLCC capacitor is recommended. 31 LGATE2 Output of the Phase 2 low-side MOSFET gate driver of the Core VR. Connect the LGATE2 pin to the gate of the Phase 2 low-side MOSFET(s). 32 PHASE2 Current return path for the Phase 2 high-side MOSFET gate driver of the Core VR. Connect the PHASE2 pin to the node consisting of the high-side MOSFET source, the low-side MOSFET drain and the output inductor of Phase 2. 33 UGATE2 Output of the Phase 2 high-side MOSFET gate driver of the Core VR. Connect the UGATE2 pin to the gate of the Phase 2 high-side MOSFET(s). 34 BOOT2 Connect an MLCC capacitor across the BOOT2 and PHASE2 pins. The boot capacitor is charged, through an internal boot diode connected from the VDDP pin to the BOOT2 pin, each time the PHASE2 pin drops below VDDP minus the voltage dropped across the internal boot diode. 35 VIN 36 BOOTX FN8410 Rev 1.00 November 19, 2015 5V bias power. A resistor [2Ω] and a decoupling capacitor should be used from the +5V supply. A high quality, X7R dielectric MLCC capacitor is recommended. Battery supply voltage, used for feed-forward. Boot connection of the programmable internal driver used for either Channel 3 of the Core VR or Channel 1 of the Northbridge VR based on the configuration state selected by the FCCM_NB resistor. Connect an MLCC capacitor across the BOOT1X and the PHASEX pins. The boot capacitor is charged, through an internal boot diode connected from the VDDP pin to the BOOTX pin, each time the PHASEX pin drops below VDDP minus the voltage dropped across the internal boot diode. Page 9 of 37 ISL62773A Pin Descriptions (Continued) PIN NUMBER SYMBOL DESCRIPTION 37 UGATEX High-side MOSFET gate driver portion of the programmable internal driver used for either Channel 3 of the Core VR or Channel 1 of the Northbridge VR based on the configuration state selected by the FCCM_NB resistor. Connect the UGATEX pin to the gate of the high-side MOSFET(s) for either Phase 3 of the Core VR or Phase 1 of the Northbridge VR based on the configuration state selected. 38 PHASEX Phase connection of the programmable internal driver used for either Channel 3 of the Core VR or Channel 1 of the Northbridge VR based on the configuration state selected by the FCCM_NB resistor. Current return path for the high-side MOSFET gate driver of the floating internal driver. Connect the PHASEX pin to the node consisting of the high-side MOSFET source, the low-side MOSFET drain and the output inductor of either Phase 3 of the Core VR or Phase 1 of the Northbridge VR based on the configuration state selected. 39 LGATEX Low-side MOSFET gate driver portion of floating internal driver used for either Channel 3 of the Core VR or Channel 1 of the Northbridge VR based on the configuration state selected by the FCCM_NB resistor. Connect the LGATEX pin to the gate of the low-side MOSFET(s) for either Phase 3 of the Core VR or Phase 1 of the Northbridge VR based on the configuration state selected. 40 PWM2_NB PWM output for Channel 2 of the Northbridge VR. Disabled when ISEN2_NB is tied to +5V. 41 FCCM_NB Diode emulation control signal for Intersil MOSFET Drivers. When FCCM_NB is LOW, diode emulation at the driver this pin connects to is allowed. A resistor from FCCM_NB pin to GND configures the PWM_Y and floating internal gate driver [BOOTX, UGATEX, PHASEX, LGATEX pins] to support Phase 3 of the Core VR and Phase 1 of the Northbridge VR. The FCCM_NB resistor value also is used to set the slew rate for the Core VR and Northbridge VR. A capacitor place holder from the FCCM_NB pin to GND is recommended for filtering noise on this pin due to layout. 42 PGOOD_NB Open-drain output to indicate the Northbridge portion of the IC is ready to supply regulated voltage. Pull up externally to VDDP or 3.3V through a resistor. 43 COMP_NB Northbridge VR error amplifier output. A resistor from COMP_NB to GND sets the Northbridge VR offset voltage and is used to set the switching frequency for the Core VR and Northbridge VR. 44 FB_NB 45 VSEN_NB Output voltage sense pin for the Northbridge controller. Connect to the +sense pin of the microprocessor die. 46 ISUMN_NB Inverting input of the transconductance amplifier for current monitor and load line of the Northbridge VR. 47 ISUMP_NB Noninverting input of the transconductance amplifier for current monitor and load line of the Northbridge VR. 48 ISEN1_NB Individual current sensing for Channel 1 of the Northbridge VR. If ISEN2_NB is tied to +5V, this pin cannot be left open and must be tied to GND with a 10kΩ resistor. If ISEN1_NB is tied to +5V, the Northbridge portion of the IC is shutdown. GND (Bottom Pad) Output voltage feedback to the inverting input of the Northbridge controller error amplifier. Signal common of the IC. Unless otherwise stated, signals are referenced to the GND pin. Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING TEMP. RANGE (°C) PACKAGE (RoHS Compliant) PKG. DWG. # ISL62773AHRZ 62773A HRZ -10 to +100 48 Ld 6x6 QFN L48.6x6B ISL62773AIRZ 62773A IRZ -40 to +100 48 Ld 6x6 QFN L48.6x6B NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL62773A. For more information on MSL please see tech brief TB363. FN8410 Rev 1.00 November 19, 2015 Page 10 of 37 ISL62773A Absolute Maximum Ratings Thermal Information Supply Voltage, VDD, VDDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +7V Battery Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +28V Boot Voltage (BOOT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +33V Boot to Phase Voltage (BOOT-PHASE) . . . . . . . . . . . . . . . . -0.3V to +7V (DC) -0.3V to +9V (<10ns) Phase Voltage (PHASE) . . . . . . . . . . . . . . . . -7V (<20ns Pulse Width, 10µJ) UGATE Voltage (UGATE) . . . . . . . . . .PHASE - 0.3V (DC) to BOOTPHASE - 5V (<20ns Pulse Width, 10µJ) to BOOT LGATE Voltage -2.5V (<20ns Pulse Width, 5µJ) to VDD + 0.3V All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (VDD + 0.3V) Open-Drain Outputs, PGOOD, PGOOD_NB, VR_HOT_L. . . . . . . -0.3V to +7V Thermal Resistance (Typical) JA (°C/W) JC (°C/W) 48 Ld QFN Package (Notes 4, 5) . . . . . . . . 29 3.5 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150°C Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . .+150°C Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493 Recommended Operating Conditions Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±5% Battery Voltage, VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 25V Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . . HRZ, -10°C to +100°C IRZ, -40°C to +100°C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-10°C to +125°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech Brief TB379. 5. For JC, the “case temp” location is the center of the exposed metal pad on the package underside. Electrical Specifications Operating Conditions: VDD = 5V, TA = -10°C to +100°C (HRZ), TA = -40°C to +100°C (IRZ), fSW = 300kHz, unless otherwise noted. Boldface limits apply across the operating temperature range, -40°C to +100°C. PARAMETER SYMBOL TEST CONDITIONS MIN (Note 6) TYP MAX (Note 6)) UNIT 8 11 mA µA INPUT POWER SUPPLY ENABLE = 1V +5V Supply Current IVDD ENABLE = 0V 1 Battery Supply Current IVIN ENABLE = 0V 1 VIN Input Resistance RVIN ENABLE = 1V 620 µA kΩ POWER-ON-RESET THRESHOLDS VDD POR Threshold VDD_PORr VDD rising VDD_PORf VDD falling 4.00 4.35 No load; closed loop, active mode range, VID = 0.75V to 1.55V -0.5 4.50 4.15 V V SYSTEM AND REFERENCES System Accuracy HRZ %Error (VOUT) IRZ %Error (VOUT) +0.5 % VID = 0.25V to 0.74375V -10 +10 mV No load; closed loop, active mode range, VID = 0.75V to 1.55V -0.8 +0.8 % VID = 0.25V to 0.74375V -12 +12 mV Maximum Output Voltage VOUT(max) VID = [00000000] 1.55 V Minimum Output Voltage VOUT(min) VID = [11111111] 0 V CHANNEL FREQUENCY Nominal Channel Frequency 280 fSW(nom) Adjustment Range 300 300 320 kHz 450 kHz AMPLIFIERS Current-Sense Amplifier Input Offset Error Amp DC Gain Error Amp Gain-Bandwidth Product FN8410 Rev 1.00 November 19, 2015 HRZ IFB = 0A -0.15 +0.15 mV IRZ IFB = 0A -0.20 +0.20 mV Av0 GBW CL = 20pF 119 dB 17 MHz Page 11 of 37 ISL62773A Electrical Specifications Operating Conditions: VDD = 5V, TA = -10°C to +100°C (HRZ), TA = -40°C to +100°C (IRZ), fSW = 300kHz, unless otherwise noted. Boldface limits apply across the operating temperature range, -40°C to +100°C. (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN (Note 6) TYP MAX (Note 6)) UNIT ISEN Input Bias Current 20 nA POWER-GOOD (PGOOD AND PGOOD_NB) AND PROTECTION MONITORS PGOOD Low Voltage VOL IPGOOD = 4mA PGOOD Leakage Current IOH PGOOD = 3.3V -1 PWROK High Threshold 750 VR_HOT_L Pull-Down 11 0.4 V 1 µA mV Ω PWROK Leakage Current 1 µA VR_HOT_L Leakage Current 1 µA 1.5 Ω GATE DRIVER UGATE Pull-Up Resistance RUGPU 200mA source current 1.0 UGATE Source Current IUGSRC UGATE - PHASE = 2.5V 2 UGATE Sink Resistance RUGPD 250mA sink current UGATE Sink Current IUGSNK UGATE - PHASE = 2.5V 2 1.0 1.0 A 1.5 Ω A LGATE Pull-Up Resistance RLGPU 250mA source current LGATE Source Current ILGSRC LGATE - VSSP = 2.5V 2 1.5 Ω LGATE Sink Resistance RLGPD 250mA sink current 0.5 0.9 Ω LGATE Sink Current ILGSNK LGATE - VSSP = 2.5V 4 A UGATE to LGATE Dead Time tUGFLGR UGATE falling to LGATE rising, no load 23 ns LGATE to UGATE Dead Time tLGFUGR LGATE falling to UGATE rising, no load 28 ns A PROTECTION Overvoltage Threshold OVH VSEN rising above setpoint for >1µs 275 325 375 mV Undervoltage Threshold OVH VSEN falls below setpoint for >1µs 275 325 375 mV Current Imbalance Threshold One ISEN above another ISEN for >1.2ms 9 mV 15 µA Way Overcurrent Trip Threshold [IMONx Current Based Detection] IMONxWOC All states, IDROOP = 60µA, RIMON = 135kΩ Overcurrent Trip Threshold [IMONx Voltage Based Detection] VIMONx_OCP All states, IDROOP = 45µA, IIMONx = 11.25µA, RIMON = 135kΩ 1.485 1.510 1.535 V 1 V LOGIC THRESHOLDS ENABLE Input Low ENABLE Input High ENABLE Leakage Current VIL VIH HRZ 1.6 VIH IRZ 1.65 IENABLE ENABLE = 0V -1 ENABLE = 1V SVT Impedance V V 0 1 µA 18 35 µA 30 % 50 SVC, SVD Input Low VIL SVC, SVD Input High VIH SVC, SVD Leakage % of VDDIO Ω % of VDDIO 70 ENABLE = 0V, SVC, SVD = 0V and 1V -1 1 µA % ENABLE = 1V, SVC, SVD = 1V -5 1 µA ENABLE = 1V, SVC, SVD = 0V -35 -5 µA 1.0 V -20 PWM PWM Output Low V0L PWM Output High V0H PWM Tri-State Leakage FN8410 Rev 1.00 November 19, 2015 Sinking 5mA Sourcing 5mA PWM = 2.5V 3.5 V 1 µA Page 12 of 37 ISL62773A Electrical Specifications Operating Conditions: VDD = 5V, TA = -10°C to +100°C (HRZ), TA = -40°C to +100°C (IRZ), fSW = 300kHz, unless otherwise noted. Boldface limits apply across the operating temperature range, -40°C to +100°C. (Continued) PARAMETER SYMBOL TEST CONDITIONS MIN (Note 6) TYP MAX (Note 6)) UNIT THERMAL MONITOR NTC Source Current NTC = 0.6V NTC Thermal Warning Voltage 27 30 33 µA 600 640 680 mV NTC Thermal Warning Voltage Hysteresis 20 NTC Thermal Shutdown Voltage mV 530 580 630 mV Maximum programmed 16 20 24 mV/µs Minimum programmed 8 10 12 mV/µs SLEW RATE VID-on-the-Fly Slew Rate NOTE: 6. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. Gate Driver Timing Diagram PWM tLGFUGR tFU tRU 1V UGATE 1V LGATE tFL tRL tUGFLGR FIGURE 8. GATE DRIVER TIMING DIAGRAM FN8410 Rev 1.00 November 19, 2015 Page 13 of 37 ISL62773A Theory of Operation VW Multiphase R3™ Modulator VCRM The ISL62773A is a multiphase regulator implementing two voltage regulators, CORE VR and Northbridge (NB) VR, on one chip controlled by AMD’s™ SVI2™ protocol. The CORE VR can be programmed for 1-, 2- or 3-phase operation. The Northbridge VR can be configured for 1- or 2-phase operation. Both regulators use the Intersil patented R3™ (Robust Ripple Regulator) Modulator. The R3™ Modulator combines the best features of fixed frequency PWM and hysteretic PWM while eliminating many of their shortcomings. Figure 9 conceptually shows the multiphase R3™ Modulator circuit, and Figure 10 shows the operation principles. COMP VW MASTER CLOCK COMP VCRM GMVO MASTER CLOCK CIRCUIT MASTER CLOCK PHASE SEQUENCER HYSTERETIC WINDOW MASTER CLOCK CLOCK1 PWM1 CLOCK2 PWM2 CLOCK3 CLOCK1 CLOCK2 CLOCK3 PWM3 VW CRM SLAVE CIRCUIT 1 VW CLOCK1 S R VCRS1 Q PWM1 PHASE1 L1 VO VCRS2 IL1 CRS1 SLAVE CIRCUIT 2 CLOCK2 S R VCRS2 Q PWM2 PHASE2 L2 IL2 GM CRS2 SLAVE CIRCUIT 3 VW CLOCK3 VCRS3 S R Q PWM3 PHASE3 L3 IL3 GM CRS3 FIGURE 9. R3™ MODULATOR CIRCUIT Inside the IC, the modulator uses the master clock circuit to generate the clocks for the slave circuits. The modulator discharges the ripple capacitor Crm with a current source equal to gmVo, where gm is a gain factor. Crm voltage, VCRM, is a sawtooth waveform traversing between the VW and COMP voltages. It resets to VW when it hits COMP and generates a one-shot master clock signal. A phase sequencer distributes the master clock signal to the slave circuits. If the CORE VR is in 3-phase mode, the master clock signal is distributed to the three phases, and the Clock 1~3 signals will be 120° out-of-phase. If the Core VR is in 2-phase mode, the master clock signal is distributed to Phases 1 and 2, and the Clock1 and Clock2 signals will be 180° out-of-phase. If the Core VR is in 1-phase mode, the master clock signal will be distributed to Phase 1 only and be the Clock1 signal. FN8410 Rev 1.00 November 19, 2015 VCRS1 FIGURE 10. R3™ MODULATOR OPERATION PRINCIPLES IN STEADY STATE GM VW VCRS3 CO Each slave circuit has its own ripple capacitor Crs, whose voltage mimics the inductor ripple current. A gm amplifier converts the inductor voltage into a current source to charge and discharge Crs. The slave circuit turns on its PWM pulse upon receiving the clock signal, and the current source charges Crs. When Crs voltage VCrs hits VW, the slave circuit turns off the PWM pulse, and the current source discharges Crs. Since the controller works with Vcrs, which are large amplitude and noise-free synthesized signals, it achieves lower phase jitter than conventional hysteretic mode and fixed PWM mode controllers. Unlike conventional hysteretic mode converters, the error amplifier allows the ISL62773A to maintain a 0.5% output voltage accuracy. Figure 11 shows the operation principles during load insertion response. The COMP voltage rises during load insertion, generating the master clock signal more quickly, so the PWM pulses turn on earlier, increasing the effective switching frequency. This allows for higher control loop bandwidth than conventional fixed frequency PWM controllers. The VW voltage rises as the COMP voltage rises, making the PWM pulses wider. During load release response, the COMP voltage falls. It takes the master clock circuit longer to generate the next master clock signal so the PWM pulse is held off until needed. The VW voltage falls as the COMP voltage falls, reducing the current PWM pulse width. This kind of behavior gives the ISL62773A excellent response speed. The fact that all the phases share the same VW window voltage also ensures excellent dynamic current balance among phases. Page 14 of 37 ISL62773A current will never reach 0A, and the regulator is in CCM, although the controller is in DE mode. VW Figure 13 shows the operation principle in diode emulation mode at light load. The load gets incrementally lighter in the three cases from top to bottom. The PWM on-time is determined by the VW window size and therefore is the same, making the inductor current triangle the same in the three cases. The ISL62773A clamps the ripple capacitor voltage VCRS in DE mode to make it mimic the inductor current. It takes the COMP voltage longer to hit VCRS, naturally stretching the switching period. The inductor current triangles move farther apart, such that the inductor current average value is equal to the load current. The reduced switching frequency helps increase light-load efficiency. COMP V CRM MASTER CLOCK CLOCK1 PWM1 CLOCK2 PWM2 CLOCK3 VW CCM/DCM BOUNDARY V CRS PWM3 VW IL VW LIGHT DCM VCRS1 VCRS3 VCRS2 FIGURE 11. R3™ MODULATOR OPERATION PRINCIPLES IN LOAD INSERTION RESPONSE Diode Emulation and Period Stretching The ISL62773A can operate in Diode Emulation (DE) mode to improve light-load efficiency. In DE mode, the low-side MOSFET conducts when the current is flowing from source to drain and does not allow reverse current, thus emulating a diode. As Figure 12 shows, when LGATE is on, the low-side MOSFET carries current, creating negative voltage on the phase node due to the voltage drop across the on-resistance. The ISL62773A monitors the current by monitoring the phase node voltage. It turns off LGATE when the phase node voltage reaches zero to prevent the inductor current from reversing the direction and creating unnecessary power loss. PHASE UGATE LGATE V CRS IL VW DEEP DCM V CRS IL FIGURE 13. PERIOD STRETCHING Channel Configuration Individual PWM channels of either VR can be disabled by connecting the ISENx pin of the channel not required to +5V. For example, placing the controller in a 2+1 configuration, as shown in Figure 5 on page 5, requires ISEN3 of the Core VR and ISEN2 of the Northbridge VR to be tied to +5V. This disables Channel 3 of the Core VR and Channel 2 of the Northbridge VR. ISEN1_NB must be tied through a 10kΩ resistor to GND to prevent this pin from pulling high and disabling the channel. Connecting ISEN1 or ISEN1_NB to +5V will disable the corresponding VR output. This feature allows debug of individual VR outputs. Power-On Reset IL FIGURE 12. DIODE EMULATION If the load current is light enough, as Figure 12 shows, the inductor current reaches and stays at zero before the next phase node pulse, and the regulator is in Discontinuous Conduction Mode (DCM). If the load current is heavy enough, the inductor FN8410 Rev 1.00 November 19, 2015 Before the controller has sufficient bias to guarantee proper operation, the ISL62773A requires a +5V input supply tied to VDD and VDDP to exceed the VDD rising Power-On Reset (POR) threshold. Once this threshold is reached or exceeded, the ISL62773A has enough bias to check the state of the SVI inputs once ENABLE is taken high. Hysteresis between the rising and the falling thresholds assure the ISL62773A does not inadvertently turn off unless the bias voltage drops substantially (see “Electrical Specifications” on page 11). Note that VIN must be present for the controller to drive the output voltage. Page 15 of 37 ISL62773A 1 2 3 4 5 6 7 8 VDD SVC SVD VOTF SVT TELEMETRY TELEMETRY ENABLE PWROK METAL_VID VCORE/ VCORE_NB V_SVI PGOOD & PGOOD_NB Interval 1 to 2: ISL62773A waits to POR. Interval 2 to 3: SVC and SVD are externally set to pre-Metal VID code. Interval 3 to 4: ENABLE locks pre-Metal VID code. Both outputs soft-start to this level. Interval 4 to 5: PGOOD signal goes HIGH, indicating proper operation. Interval 5 to 6: PGOOD and PGOOD_NB high is detected and PWROK is taken high. The ISL62773A is prepared for SVI commands. Interval 6 to 7: SVC and SVD data lines communicate change in VID code. Interval 7 to 8: ISL62773A responds to VID-ON-THE-FLY code change and issues a VOTF for positive VID changes. Post 8: Telemetry is clocked out of the ISL62773A. FIGURE 14. SVI INTERFACE TIMING DIAGRAM: TYPICAL PRE-PWROK METAL VID START-UP Start-Up Timing With VDD above the POR threshold, the controller start-up sequence begins when ENABLE exceeds the logic high threshold. Figure 15 shows the typical soft-start timing of the Core and Northbridge VRs. Once the controller registers ENABLE as a high, the controller checks that state of a few programming pins during the typical 8ms delay prior to beginning soft-starting the Core and Northbridge outputs. The pre-PWROK Metal VID is read from the state of the SVC and SVD pins and programs the DAC, the programming resistors on COMP, COMP_NB, and FCCM_NB are read to configure internal drivers, switching frequency, slew rate and output offsets. These programming resistors are discussed in subsequent sections. The ISL62773A uses a digital soft-start to ramp up the DAC to the Metal VID level programmed. The soft-start slew rate is programmed by the FCCM_NB resistor which is used to set the VID-on-the-fly slew rate as well. See “VID-on-the-Fly Slew Rate Selection” on page 21 for more details on selecting the FCCM_NB resistor. PGOOD is asserted high at the end of the soft-start ramp. FN8410 Rev 1.00 November 19, 2015 VDD SLEW RATE ENABLE 8ms MetalVID VID COMMAND VOLTAGE DAC PGOOD PWROK VIN FIGURE 15. TYPICAL SOFT-START WAVEFORMS Voltage Regulation and Load Line Implementation After the soft-start sequence, the ISL62773A regulates the output voltages to the pre-PWROK metal VID programmed, see Table 6. The ISL62773A controls the no-load output voltage to an accuracy of ±0.5% over the range of 0.75V to 1.55V. A differential amplifier allows voltage sensing for precise voltage regulation at the microprocessor die. Page 16 of 37 ISL62773A Differential Sensing R droop + FB Vdroop VCCSENSE - VR LOCAL VO Idroop "CATCH" RESISTOR + E/A COMP SVC + VDAC INTERNAL TO IC DAC SVD SVID[7:0] RTN X1 - VCC SENSE + V VSS "CATCH" RESISTOR FIGURE 16. DIFFERENTIAL SENSING AND LOAD LINE IMPLEMENTATION As the load current increases from zero, the output voltage droops from the VID programmed value by an amount proportional to the load current, to achieve the load line. The ISL62773A can sense the inductor current through the intrinsic DC Resistance (DCR) of the inductors, as shown in Figures 3 and 4, or through resistors in series with the inductors as shown in Figure 5. In both methods, capacitor Cn voltage represents the total inductor current. An internal amplifier converts Cn voltage into an internal current source, Isum, with the gain set by resistor Ri, see Equation 1. V Cn I sum = ----------Ri (EQ. 1) The Isum current is used for load line implementation, current monitoring on the IMON pins and overcurrent protection. Figure 16 shows the load line implementation. The ISL62773A drives a current source (Idroop) out of the FB pin which is a ratio of the Isum current, as described by Equation 2. 5 5 V Cn I droop = --- I sum = --- ----------Ri 4 4 (EQ. 2) When using inductor DCR current sensing, a single NTC element is used to compensate the positive temperature coefficient of the copper winding, thus sustaining the load line accuracy with reduced cost. Idroop flows through resistor Rdroop and creates a voltage drop as shown in Equation 3. V droop = R droop I droop droop = V DAC + VSS SENSE (EQ. 4) Rewriting Equation 4 and substituting Equation 3 gives Equation 5 the exact equation required for load line implementation. VSSSENSE + Figure 16 also shows the differential voltage sensing scheme. VCCSENSE and VSSSENSE are the remote voltage sensing signals from the processor die. A unity gain differential amplifier senses the VSSSENSE voltage and adds it to the DAC output. The error amplifier regulates the inverting and noninverting input voltages to be equal as shown in Equation 4: (EQ. 3) Vdroop is the droop voltage required to implement load line. Changing Rdroop or scaling Idroop can change the load line slope. Since Isum sets the overcurrent protection level, it is recommended to first scale Isum based on OCP requirement, then select an appropriate Rdroop value to obtain the desired load line slope. VCC SENSE – VSS SENSE = V DAC – R droop I droop (EQ. 5) The VCCSENSE and VSSSENSE signals come from the processor die. The feedback is open circuit in the absence of the processor. As Figure 16 shows, it is recommended to add a “catch” resistor to feed the VR local output voltage back to the compensator, and to add another “catch” resistor to connect the VR local output ground to the RTN pin. These resistors, typically 10Ω~100Ω, provide voltage feedback if the system is powered up without a processor installed. Phase Current Balancing Rdcr3 L3 ISEN3 PHASE3 Risen Cisen INTERNAL TO IC ISEN2 ISEN1 IL3 PHASE1 Risen Rdcr2 L2 PHASE2 Risen Cisen Rpcb3 Rpcb2 VO IL2 Rdcr1 L1 Rpcb1 IL1 Cisen FIGURE 17. CURRENT BALANCING CIRCUIT The ISL62773A monitors individual phase average current by monitoring the ISEN1, ISEN2 and ISEN3 voltages. Figure 17 shows the recommended current balancing circuit for DCR sensing. Each phase node voltage is averaged by a low-pass filter consisting of Risen and Cisen, and is presented to the corresponding ISEN pin. Risen should be routed to the inductor phase-node pad in order to eliminate the effect of phase node parasitic PCB DCR. Equations 6 through 8 give the ISEN pin voltages: V ISEN1 = R dcr1 + R pcb1 I L1 (EQ. 6) V ISEN2 = R dcr2 + R pcb2 I L2 (EQ. 7) V ISEN3 = R dcr3 + R pcb3 I L3 (EQ. 8) Where Rdcr1, Rdcr2 and Rdcr3 are inductor DCR; Rpcb1, Rpcb2 and Rpcb3 are parasitic PCB DCR between the inductor output side pad and the output voltage rail; and IL1, IL2 and IL3 are inductor average currents. FN8410 Rev 1.00 November 19, 2015 Page 17 of 37 ISL62773A The ISL62773A will adjust the phase pulse-width relative to the other phases to make VISEN1 = VISEN2 = VISEN3, thus to achieve IL1 = IL2 = IL3, when Rdcr1 = Rdcr2 = Rdcr3 and Rpcb1 = Rpcb2 = Rpcb3. Using the same components for L1, L2 and L3 provides a good match of Rdcr1, Rdcr2 and Rdcr3. Board layout determines Rpcb1, Rpcb2 and Rpcb3. It is recommended to have a symmetrical layout for the power delivery path between each inductor and the output voltage rail, such that Rpcb1 = Rpcb2 = Rpcb3. PHASE3 R isen ISEN3 Cisen INTERNAL TO IC ISEN2 Cisen V3p Rdcr3 L3 Rdcr2 L2 IL2 Rpcb2 Vo Rewriting Equation 12 gives Equation 14: V 1p – V 1n = V 2p – V 2n (EQ. 14) (EQ. 15) V 1p – V 1n = V 2p – V 2n = V 3p – V 3n R dcr1 I L1 = R dcr2 I L2 = R dcr3 I L3 Rdcr1 L1 IL1 (EQ. 16) Therefore: V2n Rpcb1 (EQ. 17) Current balancing (IL1 = IL2 = IL3) is achieved when Rdcr1 = Rdcr2 = Rdcr3. Rpcb1, Rpcb2 and Rpcb3 do not have any effect. V1n R isen FIGURE 18. DIFFERENTIAL-SENSING CURRENT BALANCING CIRCUIT Sometimes, it is difficult to implement symmetrical layout. For the circuit shown in Figure 17, asymmetric layout causes different Rpcb1, Rpcb2 and Rpcb3 values, thus creating a current imbalance. Figure 18 shows a differential sensing current balancing circuit recommended for ISL62773A. The current sensing traces should be routed to the inductor pads so they only pick up the inductor DCR voltage. Each ISEN pin sees the average voltage of three sources: its own, phase inductor phase-node pad, and the other two phase inductor output side pads. Equations 9 through 11 give the ISEN pin voltages: V ISEN1 = V 1p + V 2n + V 3n (EQ. 9) V ISEN2 = V 1n + V 2p + V 3n (EQ. 10) V ISEN3 = V 1n + V 2n + V 3p (EQ. 11) FN8410 Rev 1.00 November 19, 2015 (EQ. 13) Combining Equation 14 and 15 gives: R isen R isen V 1n + V 2p + V 3n = V 1n + V 2n + V 3p V3n R isen ISEN1 C isen (EQ. 12) Rewriting Equation 13 gives Equation 15: Rpcb3 R isen PHASE1 V1p R isen V 1p + V 2n + V 3n = V 1n + V 2p + V 3n V 2p – V 2n = V 3p – V 3n IL3 R isen V2p PHASE2 R isen The ISL62773A will make VISEN1 = VISEN2 = VISEN3 as shown in Equations 12 and 13: Since the slave ripple capacitor voltages mimic the inductor currents, the R3™ modulator can naturally achieve excellent current balancing during steady state and dynamic operations. Figure 19 shows the current balancing performance of the evaluation board with load transient of 12A/51A at different rep rates. The inductor currents follow the load current dynamic change with the output capacitors supplying the difference. The inductor currents can track the load current well at a low repetition rate, but cannot keep up when the repetition rate gets into the hundred-kHz range, where it is out of the control loop bandwidth. The controller achieves excellent current balancing in all cases installed. Page 18 of 37 ISL62773A REP RATE = 10kHz Modes of Operation TABLE 1. CORE VR MODES OF OPERATION CONFIG. ISEN3 PSL0_L AND PSI1_L ISEN2 3-phase Core VR To Power To Power Stage Stage 2-phase Core VR Tied to 5V To Power Stage REP RATE = 25kHz 1-phase Core VR Tied to 5V Tied to 5V MODE 11 3-phase CCM 01 2-phase CCM 00 1-phase DE 11 2-phase CCM 01 1-phase CCM 00 1-phase DE 11 1-phase CMM IMON OCP THRESHOLD 1.5V 1.5V 1.5V 01 00 1-phase DE The Core VR can be configured for 3, 2- or 1-phase operation. Table 1 shows Core VR configurations and operational modes, programmed by the ISEN3 and ISEN2 pin status and the PSL0_L and PSL1_L commands via the SVI 2 interface, see Table 9. REP RATE = 50kHz For a 2-phase configuration, tie the ISEN3 pin to 5V. In this configuration, phases 1 and 2 are active. To select a 1-phase configuration, tie the ISEN3 pin and the ISEN2 pin to 5V. In this configuration, only phase-1 is active. In a 3-phase configuration, the Core VR operates in 3-phase CCM, with PSI0_L and PSI_L both high. If PSI0_L is taken low via the SVI 2 interface, the Core VR sheds Phase 3 and continues to operate in 2-phase CCM. When both PSI0_L and PSI1_L are taken low, the Core VR drops Phase2 and enters 1-phase DE mode. REP RATE = 100kHz For 2-phase configurations, the Core VR operates in 2-phase CCM with PSI0_L and PSI_L both high. If PSI0_L is taken low via the SVI 2 interface, the Core VR sheds Phase 2 and continues to operate in CCM. When both PSI0_L and PSI1_L are taken low, the Core VR enters 1-phase DE mode. In a 1-phase configuration, the Core VR operates in 1-phase CCM when PSI0_L is high or low. When both PSI0_l and PSI1_L are taken low, the VR enters 1-phase DE mode. The Core VR can be disabled completely by connecting ISEN1 to +5V. REP RATE = 200kHz ISL62773A Northbridge VR can be configured for 2- or 1-phase operation. Table 2 shows the Northbridge VR configurations and operational modes, which are programmed by the ISEN2_NB pin status and the PSI0_L and PSI1_L bits of the SVI 2 command. TABLE 2. NORTHBRIDGE VR MODES OF OPERATION ISEN2_NB To Power Stage FIGURE 19. CURRENT BALANCING DURING DYNAMIC OPERATION. CH1: IL1 , CH2: ILOAD, CH3: IL2, CH4: IL3 CONFIG. 2-phase NB VR Tied to 5V 1-phase NB VR PSL0_L AND PSI1_L 11 2-phase CCM 01 1-phase CCM 00 1-phase DE 11 1-phase CCM IMON OCP THRESHOLD 1.5V 1.5V 01 00 FN8410 Rev 1.00 November 19, 2015 MODE 1-phase DE Page 19 of 37 ISL62773A In a 1-phase configuration, the ISEN2_NB pin is tied to +5V. The Northbridge VR operates in 1-phase CCM and enters 1-phase DE when both PSI0_L and PSI1_L are low. The Northbridge VR can be disabled completely by tying ISEN1_NB to 5V. The Core and Northbridge VRs have an overcurrent threshold of 1.5V on IMON and IMON_NB respectively, and this level does not vary based on channel configuration. See the “Overcurrent” subsection on page 26, of “Protection Features” for more details. Dynamic Operation Core VR and Northbridge VR behave the same during dynamic operation. The controller responds to VID-on-the-fly changes by slewing to the new voltage at the slew rate programmed, see Table 4. During negative VID transitions, the output voltage decays to the lower VID value at the slew rate determined by the load. The R3™ modulator intrinsically has voltage feed-forward. The output voltage is insensitive to a fast slew rate input voltage change. FB2 Function CONTROLLER IN 2-PHASE MODE C2 VSEN R3 R2 CONTROLLER IN 1-PHASE MODE C3.1 C2 R 3 C3.2 FB2 R1 E/A FB VREF C1 VSEN The ISL62773A uses the COMP, COMP_NB and FCCM_NB pins to configure some functionality within the IC. Resistors from these pins to GND are read during the first portion of the soft-start sequence. The following sections outline how to select the resistor values for each of these pins to correctly program the output voltage offset of each output, the configuration of the floating DriverX and PWM_Y output, VID-on-the-fly slew rate and switching frequency used for both VRs. R2 C3.1 FB2 C3.2 R1 COMP FB VREF In DCM, the controller turns off the low-side MOSFET when the inductor current approaches zero. During on-time of the low-side MOSFET, phase voltage is negative and the amount is the MOSFET rDS(ON) voltage drop, which is proportional to the inductor current. A phase comparator inside the controller monitors the phase voltage during on-time of the low-side MOSFET and compares it with a threshold to determine the zero crossing point of the inductor current. If the inductor current has not reached zero when the low-side MOSFET turns off, it will flow through the low-side MOSFET body diode, causing the phase node to have a larger voltage drop until it decays to zero. If the inductor current has crossed zero and reversed the direction when the low-side MOSFET turns off, it will flow through the high-side MOSFET body diode, causing the phase node to have a spike until it decays to zero. The controller continues monitoring the phase voltage after turning off the low-side MOSFET. To minimize the body diode-related loss, the controller also adjusts the phase comparator threshold voltage accordingly in iterative steps such that the low-side MOSFET body diode conducts for approximately 40ns. Resistor Configuration Options The Core VR features an FB2 pin. The FB2 function is only available when the Core VR is in a 2-phase configuration. C1 Adaptive Body Diode Conduction Time Reduction E/A COMP FIGURE 20. FB2 FUNCTION Figure 20 shows the FB2 function. A switch (called FB2 switch) turns on to short the FB and the FB2 pins when the controller is in 2-phase mode. Capacitors C3.1 and C3.2 are in parallel, serving as part of the compensator. When the controller enters 1-phase mode, the FB2 switch turns off, removing C3.2 and leaving only C3.1 in the compensator. The compensator gain increases with the removal of C3.2. By properly sizing C3.1 and C3.2, the compensator can be optimal for both 2-phase mode and 1-phase mode. VR Offset Programming A positive or negative offset is programmed for the Core VR using a resistor to ground from the COMP pin and the Northbridge in a similar manner from the COMP_NB pin. Table 3 provides the resistor value to select the desired output voltage offset. The 1% tolerance resistor value shown in the table must be used to program the corresponding Core or NB output voltage offset. The MIN and MAX tolerance values provide margin to insure the 1% tolerance resistor will be read correctly. When the FB2 switch is off, C3.2 is disconnected from the FB pin. However, the controller still actively drives the FB2 pin voltage to follow the FB pin voltage such that C3.2 voltage always follows C3.1 voltage. When the controller turns on the FB2 switch, C3.2 is reconnected to the compensator smoothly. The FB2 function ensures excellent transient response in both 2-phase and 1-phase mode. If the FB2 function is not used, populate C3.1 only. FN8410 Rev 1.00 November 19, 2015 Page 20 of 37 ISL62773A TABLE 3. COMP AND COMP_NB OUTPUT VOLTAGE OFFSET SELECTION TABLE 4. FCCM_NB RESISTOR SELECTION RESISTOR VALUE [kΩ] MIN TOLERANCE 1% TOLERANCE VALUE MAX TOLERANCE VCORE OFFSET [mV] COMP_NB OFFSET [mV] 5.54 5.62 5.70 -43.75 18.75 7.76 7.87 7.98 -37.5 31.25 11.33 11.5 11.67 -31.25 43.76 16.65 16.9 17.15 -25 50 19.3 19.6 19.89 -18.75 37.5 24.53 24.9 25.27 -12.5 25 33.49 34.0 34.51 -6.25 12.5 40.58 41.2 41.81 6.25 0 51.52 52.3 53.08 18.75 18.75 72.10 73.2 74.29 31.25 31.25 93.87 95.3 96.72 43.76 43.76 119.19 121 122.81 50 50 151.69 154 156.31 37.5 37.5 179.27 182 184.73 25 25 206.85 210 213.15 12.5 12.5 0 0 OPEN COMP Floating DriverX AND PWM_Y Configuration The ISL62773A allows for one internal driver and one PWM output to be configured to opposite VRs depending on the desired configuration of the Northbridge VR. Internal DriverX can be used as Channel 1 of the Northbridge VR with PWM_Y used for Channel 3 of the Core VR. Using this partitioning, a 2+1 or 1+1 configured ISL62773A would not require an external driver. If routing of the driver signals would be a cause of concern due to having an internal driver on the Northbridge VR, then the ISL62773A can be configured to use PWM_Y as Channel 1 on the Northbridge VR. DriverX would then be used as Channel 3 of the Core VR. This allows the placement of the external drivers for the Northbridge VR to be closer to the output stage(s) depending on the number of active Phases, providing placement and layout flexibility to the Northbridge VR. The floating internal driver and PWM output are configured based on the programming resistor from FCCM_NB to GND. The FCCM_NB programming resistor value also sets the slew rate and switching frequency of the Core and Northbridge VRs. These features are outlined in the following sections. Table 4 shows which resistor values sets the configuration and slew rate for the ISL63773A. The resistor value shown in the table must be used and the resistor tolerance must be 1%. The MIN and MAX tolerance around each resistor value is the same as Table 3 and provides margin to insure the 1% tolerance resistor will be read correctly. FN8410 Rev 1.00 November 19, 2015 RESISTOR VALUE [kΩ] SLEW RATE FOR CORE AND NORTHBRIDGE [mV/µs] 5.62 20 7.87 15 11.5 12.5 16.9 10 19.6 20 24.9 15 34.0 12.5 41.2 10 52.3 20 73.2 15 95.3 12.5 121 10 154 20 182 15 210 12.5 OPEN 10 DriverX PWM_Y Core VR Channel 3 NB VR Channel 1 NB VR Channel 1 Core VR Channel 3 VID-on-the-Fly Slew Rate Selection The FCCM_NB resistor is also used to select the slew rate for VID changes commanded by the processor. Once selected, the slew rate is locked in during soft-start and is not adjustable during operation. The lowest slew rate which can be selected is 10mV/µs which is above the minimum of 7.5mV/µs required by the SVI 2 specification. The slew rate selected sets the slew rate for both Core and Northbridge VRs; they cannot be independently selected. CCM Switching Frequency The Core and Northbridge VR switching frequency is set by the programming resistors on COMP_NB and FCCM_NC. When the ISL62773A is in Continuous Conduction Mode (CCM), the switching frequency is not absolutely constant due to the nature of the R3™ Modulator. As explained in “Multiphase R3™ Modulator” on page 14, the effective switching frequency increases during load insertion and decreases during load release to achieve fast response. Thus, the switching frequency is relatively constant at steady state. Variation is expected when the power stage condition, such as input voltage, output voltage, load, etc. changes. The variation is usually less than 10% and does not have any significant effect on output voltage ripple magnitude. Table 5 defines the switching frequency based on the resistor values used to program the COMP_NB and FCCM_NB pins. Use the previous tables related to COMP_NB and FCCM_NB to determine the correct resistor value in these ranges to program the desired output offset, slew rate and DriverX/PWM_Y configuration. Page 21 of 37 ISL62773A TABLE 5. SWITCHING FREQUENCY SELECTION FREQUENCY [kHz] COMP_NB RANGE [kΩ] FCCM_NB RANGE [kΩ] 300 57.6 to OPEN 19.1 to 41.2 or 154 to OPEN 350 5.62 to 41.2 19.1 to 41.2 or 154 to OPEN 400 57.6 to OPEN 5.62 to 16.9 or 57.6 to 121 450 5.62 to 41.2 5.62 to 16.9 or 57.6 to 121 The controller monitors SVI commands to determine when to enter power-saving mode, implement dynamic VID changes and shut down individual outputs. AMD Serial VID Interface 2.0 The on-board Serial VID Interface 2.0 (SVI 2) circuitry allows the AMD processor to directly control the Core and Northbridge voltage reference levels within the ISL62773A. Once the PWROK signal goes high, the IC begins monitoring the SVC and SVD pins for instructions. The ISL62773A uses a Digital-to-Analog Converter (DAC) to generate a reference voltage based on the decoded SVI value. See Figure 14 on page 16 for a simple SVI interface timing diagram. Pre-PWROK Metal VID Typical motherboard start-up begins with the controller decoding the SVC and SVD inputs to determine the pre-PWROK Metal VID setting (see Table 6). Once the ENABLE input exceeds the rising threshold, the ISL62773A decodes and locks the decoded value into an on-board hold register. TABLE 6. PRE-PWROK METAL VID CODES SVC SVD OUTPUT VOLTAGE (V) 0 0 1.1 0 1 1.0 1 0 0.9 1 1 0.8 output voltages decay, based on output capacitance and load leakage resistance. If bias to VDD falls below the POR level, the ISL62773A responds in the manner previously described. Once VDD and ENABLE rise above their respective rising thresholds, the internal DAC circuitry reacquires a pre-PWROK metal VID code and the controller soft-starts. SVI Interface Active Once the Core and Northbridge VRs have successfully soft-started and PGOOD and PGOOD_NB signals transition high, PWROK can be asserted externally to the ISL62773A. Once PWROK is asserted to the IC, SVI instructions can begin as the controller actively monitors the SVI interface. Details of the SVI Bus protocol are provided in the “AMD Serial VID Interface 2.0 (SVI 2) Specification”. See AMD publication #48022. Once a VID change command is received, the ISL62773A decodes the information to determine which VR is affected and the VID target is determined by the byte combinations in Table 7. The internal DAC circuitry steps the output voltage of the VR commanded to the new VID level. During this time, one or more of the VR outputs could be targeted. In the event either VR is commanded to power-off by serial VID commands, the PGOOD signal remains asserted. If the PWROK input is deasserted, then the controller steps both the Core and the Northbridge VRs back to the stored pre-PWROK metal VID level in the holding register from initial soft-start. No attempt is made to read the SVC and SVD inputs during this time. If PWROK is reasserted, then the ISL62773A SVI interface waits for instructions. If ENABLE goes low during normal operation, all external MOSFETs are tri-stated and both PGOOD and PGOOD_NB are pulled low. This event clears the pre-PWROK metal VID code and forces the controller to check SVC and SVD upon restart, storing the pre-PWROK metal VID code found on restart. A POR event on either VCC or VIN during normal operation shuts down both regulators and both PGOOD outputs are pulled low. The pre-PWROK metal VID code is not retained. Loss of VIN during operation will typically cause the controller to enter a fault condition on one or both outputs. The controller will shut down both Core and Northbridge VRs and latch off. The pre-PWROK metal VID code is not retained during the process of cycling ENABLE to reset the fault latch and restart the controller. VID-on-the-Fly Transition Once the programming pins are read, the internal DAC circuitry begins to ramp Core and Northbridge VRs to the decoded pre-PWROK Metal VID output level. The digital soft-start circuitry ramps the internal reference to the target gradually at a fixed rate of approximately 5mV/µs until the output voltage reaches ~250mV and then at the programmed slew rate. The controlled ramp of all output voltage planes reduces inrush current during the soft-start interval. At the end of the soft-start interval, the PGOOD and PGOOD_NB outputs transition high, indicating both output planes are within regulation limits. Once PWROK is high, the ISL62773A detects this flag and begins monitoring the SVC and SVD pins for SVI instructions. The microprocessor follows the protocol outlined in the following sections to send instructions for VID-on-the-fly transitions. The ISL62773A decodes the instruction and acknowledges the new VID code. For VID codes higher than the current VID level, the ISL62773A begins stepping the commanded VR outputs to the new VID target at the fixed slew rate of 10mV/µs. Once the DAC ramps to the new VID code, a VID-on-the-Fly Complete (VOTFC) request is sent on the SVI lines. If the ENABLE input falls below the enable falling threshold, the ISL62773A tri-states both outputs. PGOOD and PGOOD_NB are pulled low with the loss of ENABLE. The Core and Northbridge VR When the VID codes are lower than the current VID level, the ISL62773A checks the state of power state bits in the SVI command. If power state bits are not active, the controller begins stepping the regulator output to the new VID target. If the power FN8410 Rev 1.00 November 19, 2015 Page 22 of 37 ISL62773A state bits are active, the controller allows the output voltage to decay and slowly steps the DAC down with the natural decay of the output. This allows the controller to quickly recover and move to a high VID code if commanded. The controller issues a VOTFC request on the SVI lines once the SVI command is decoded and prior to reaching the final output voltage. VOTFC requests do not take priority over telemetry per the AMD SVI 2 specification. SVI Data Communication Protocol The SVI WIRE protocol is based on the I2C bus concept. Two wires [Serial Clock (SVC) and Serial Data (SVD)], carry information between the AMD processor (master) and VR controller (slave) on the bus. The master initiates and terminates SVI transactions and drives the clock, SVC, during a transaction. The AMD processor is always the master, and the voltage regulators are the slaves. The slave receives the SVI transactions and acts accordingly. Mobile SVI WIRE protocol timing is based on high-speed mode I2C. See AMD publication #48022 for additional details. . TABLE 7. SERIAL VID CODES SVID[7:0] VOLTAGE (V) SVID[7:0] VOLTAGE (V) SVID[7:0] VOLTAGE (V) SVID[7:0] VOLTAGE (V) 0000_0000 1.55000 0010_0000 1.35000 0100_0000 1.15000 0110_0000 0.95000 0000_0001 1.54375 0010_0001 1.34375 0100_0001 1.14375 0110_0001 0.94375 0000_0010 1.53750 0010_0010 1.33750 0100_0010 1.13750 0110_0010 0.93750 0000_0011 1.53125 0010_0011 1.33125 0100_0011 1.13125 0110_0011 0.93125 0000_0100 1.52500 0010_0100 1.32500 0100_0100 1.12500 0110_0100 0.92500 0000_0101 1.51875 0010_0101 1.31875 0100_0101 1.11875 0110_0101 0.91875 0000_0110 1.51250 0010_0110 1.31250 0100_0110 1.11250 0110_0110 0.91250 0000_0111 1.50625 0010_0111 1.30625 0100_0111 1.10625 0110_0111 0.90625 0000_1000 1.50000 0010_1000 1.30000 0100_1000 1.10000 0110_1000 0.90000 0000_1001 1.49375 0010_1001 1.29375 0100_1001 1.09375 0110_1001 0.89375 0000_1010 1.48750 0010_1010 1.28750 0100_1010 1.08750 0110_1010 0.88750 0000_1011 1.48125 0010_1011 1.28125 0100_1011 1.08125 0110_1011 0.88125 0000_1100 1.47500 0010_1100 1.27500 0100_1100 1.07500 0110_1100 0.87500 0000_1101 1.46875 0010_1101 1.26875 0100_1101 1.06875 0110_1101 0.86875 0000_1110 1.46250 0010_1110 1.26250 0100_1110 1.06250 0110_1110 0.86250 0000_1111 1.45625 0010_1111 1.25625 0100_1111 1.05625 0110_1111 0.85625 0001_0000 1.45000 0011_0000 1.25000 0101_0000 1.05000 0111_0000 0.85000 0001_0001 1.44375 0011_0001 1.24375 0101_0001 1.04375 0111_0001 0.84375 0001_0010 1.43750 0011_0010 1.23750 0101_0010 1.03750 0111_0010 0.83750 0001_0011 1.43125 0011_0011 1.23125 0101_0011 1.03125 0111_0011 0.83125 0001_0100 1.42500 0011_0100 1.22500 0101_0100 1.02500 0111_0100 0.82500 0001_0101 1.41875 0011_0101 1.21875 0101_0101 1.01875 0111_0101 0.81875 0001_0110 1.41250 0011_0110 1.21250 0101_0110 1.01250 0111_0110 0.81250 0001_0111 1.40625 0011_0111 1.20625 0101_0111 1.00625 0111_0111 0.80625 0001_1000 1.40000 0011_1000 1.20000 0101_1000 1.00000 0111_1000 0.80000 0001_1001 1.39375 0011_1001 1.19375 0101_1001 0.99375 0111_1001 0.79375 0001_1010 1.38750 0011_1010 1.18750 0101_1010 0.98750 0111_1010 0.78750 0001_1011 1.38125 0011_1011 1.18125 0101_1011 0.98125 0111_1011 0.78125 0001_1100 1.37500 0011_1100 1.17500 0101_1100 0.97500 0111_1100 0.77500 0001_1101 1.36875 0011_1101 1.16875 0101_1101 0.96875 0111_1101 0.76875 0001_1110 1.36250 0011_1110 1.16250 0101_1110 0.96250 0111_1110 0.76250 FN8410 Rev 1.00 November 19, 2015 Page 23 of 37 ISL62773A TABLE 7. SERIAL VID CODES (Continued) SVID[7:0] VOLTAGE (V) SVID[7:0] VOLTAGE (V) SVID[7:0] VOLTAGE (V) SVID[7:0] VOLTAGE (V) 0001_1111 1.35625 0011_1111 1.15625 0101_1111 0.95625 0111_1111 0.75625 1000_0000 0.75000 1010_0000 0.55000* 1100_0000 0.35000* 1110_0000 0.15000* 1000_0001 0.74375 1010_0001 0.54375* 1100_0001 0.34375* 1110_0001 0.14375* 1000_0010 0.73750 1010_0010 0.53750* 1100_0010 0.33750* 1110_0010 0.13750* 1000_0011 0.73125 1010_0011 0.53125* 1100_0011 0.33125* 1110_0011 0.13125* 1000_0100 0.72500 1010_0100 0.52500* 1100_0100 0.32500* 1110_0100 0.12500* 1000_0101 0.71875 1010_0101 0.51875* 1100_0101 0.31875* 1110_0101 0.11875* 1000_0110 0.71250 1010_0110 0.51250* 1100_0110 0.31250* 1110_0110 0.11250* 1000_0111 0.70625 1010_0111 0.50625* 1100_0111 0.30625* 1110_0111 0.10625* 1000_1000 0.70000 1010_1000 0.50000* 1100_1000 0.30000* 1110_1000 0.10000* 1000_1001 0.69375 1010_1001 0.49375* 1100_1001 0.29375* 1110_1001 0.09375* 1000_1010 0.68750 1010_1010 0.48750* 1100_1010 0.28750* 1110_1010 0.08750* 1000_1011 0.68125 1010_1011 0.48125* 1100_1011 0.28125* 1110_1011 0.08125* 1000_1100 0.67500 1010_1100 0.47500* 1100_1100 0.27500* 1110_1100 0.07500* 1000_1101 0.66875 1010_1101 0.46875* 1100_1101 0.26875* 1110_1101 0.06875* 1000_1110 0.66250 1010_1110 0.46250* 1100_1110 0.26250* 1110_1110 0.06250* 1000_1111 0.65625 1010_1111 0.45625* 1100_1111 0.25625* 1110_1111 0.05625* 1001_0000 0.65000 1011_0000 0.45000* 1101_0000 0.25000* 1111_0000 0.05000* 1001_0001 0.64375 1011_0001 0.44375* 1101_0001 0.24375* 1111_0001 0.04375* 1001_0010 0.63750 1011_0010 0.43750* 1101_0010 0.23750* 1111_0010 0.03750* 1001_0011 0.63125 1011_0011 0.43125* 1101_0011 0.23125* 1111_0011 0.03125* 1001_0100 0.62500 1011_0100 0.42500* 1101_0100 0.22500* 1111_0100 0.02500* 1001_0101 0.61875 1011_0101 0.41875* 1101_0101 0.21875* 1111_0101 0.01875* 1001_0110 0.61250 1011_0110 0.41250* 1101_0110 0.21250* 1111_0110 0.01250* 1001_0111 0.60625 1011_0111 0.40625* 1101_0111* 0.20625* 1111_0111 0.00625* 1001_1000 0.60000* 1011_1000 0.40000* 1101_1000 0.20000* 1111_1000 OFF* 1001_1001 0.59375* 1011_1001 0.39375* 1101_1001 0.19375* 1111_1001 OFF* 1001_1010 0.58750* 1011_1010 0.38750* 1101_1010 0.18750* 1111_1010 OFF* 1001_1011 0.58125* 1011_1011 0.38125* 1101_1011 0.18125* 1111_1011 OFF* 1001_1100 0.57500* 1011_1100 0.37500* 1101_1100 0.17500* 1111_1100 OFF* 1001_1101 0.56875* 1011_1101 0.36875* 1101_1101 0.16875* 1111_1101 OFF* 1001_1110 0.56250* 1011_1110 0.36250* 1101_1110 0.16250* 1111_1110 OFF* 1001_1111 0.55625* 1011_1111 0.35625* 1101_1111 0.15625* 1111_1111 OFF* NOTE: *Indicates a VID not required for AMD Family 10h processors. Loosened AMD requirements at these levels. FN8410 Rev 1.00 November 19, 2015 Page 24 of 37 SVC 1 2 3 4 5 6 7 8 9 10 VID BIT [0] VID BITS [7:1] 11 12 13 14 15 16 17 18 19 PSI1_L PSI0_L ISL62773A 20 21 22 23 24 25 26 27 START SVD ACK ACK ACK FIGURE 21. SVD PACKET STRUCTURE SVI Bus Protocol The AMD processor bus protocol is compliant with SMBus send byte protocol for VID transactions. The AMD SVD packet structure is shown in Figure 21. The description of each bit of the three bytes that make up the SVI command are shown in Table 8. During a transaction, the processor sends the start sequence followed by each of the three bytes which end with an optional acknowledge bit. The ISL62773A does not drive the SVD line during the ACK bit. Finally, the processor sends the stop sequence. After the ISL62773A has detected the stop, it can then proceed with the commanded action from the transaction. TABLE 8. SVD DATA PACKET BITS 1:5 6 For the Northbridge VR operating in 2-phase mode, when PSI0_L is asserted, Channel 2 is tri-stated and Channel 1 enters diode emulation mode to boost efficiency. When PSI1_L is asserted, the Core VR continues to operate in this fashion. It is possible for the processor to assert or deassert PSI0_L and PSI1_L out of order. PSI0_L takes priority over PSI1_L. If PSI0_L is deasserted while PSI1_L is still asserted, the ISL62773A will return the selected VR back full channel CCM operation. TABLE 9. PSI0_L, PSI1_L AND TFN DEFINITION FUNCTION BIT PSI0_L 10 Power state indicate level 0. When this signal is asserted (active Low) the processor is in a low enough power state for the ISL62773A to take action to boost efficiency by dropping phases and entering 1-Phase DE. PSI1_L 20 Power state indicate level 1. When this signal is asserted (active Low) the processor is in a low enough power state for the ISL62773A to take action to boost efficiency by dropping phases and entering 1-Phase DE. DESCRIPTION Always 11000b Core domain selector bit, if set then the following data byte contains VID, power state, telemetry control, load line trim and offset trim apply to the Core VR. DESCRIPTION 7 Northbridge domain selector bit, if set then the following data byte contains VID, power state, telemetry control, load line trim and offset trim apply to the Northbridge VR. 8 Always 0b Dynamic Load Line Slope Trim 9 Acknowledge bit 10 PSI0_L The ISL62773A supports the SVI 2 ability for the processor to manipulate the load line slope of the Core and Northbridge VRs independently using the serial VID interface. The slope manipulation applies to the initial load line slope. A load line slope trim will typically coincide with a VOTF change. See Table 10 for more information about the load line slope trim feature of the ISL62773A. 11:17 VID Code bits [7:1] 18 Acknowledge bit 19 VID code bit [0] 20 PSI1_L 21 TFN (Telemetry Functionality) 22:24 Load line slope trim TABLE 10. LOAD LINE SLOPE TRIM DEFINITION LOAD LINE SLOPE TRIM [2:0] DESCRIPTION 000 Disable LL 001 -40% mΩ change 010 -20% mΩ change Power States 011 No change SVI 2 defines two power state indicator levels (see Table 9). As processor current consumption reduces, the power state indicator level changes to improve VR efficiency under low power conditions. 100 +20% mΩ change 101 +40% mΩ change 110 +60% mΩ change For the Core VR operating in 3-phase mode, when PSI0_L is asserted Channels 2 and 3 are tri-stated and Channel 1 enters diode emulation mode to boost efficiency. When PSI1_L is asserted, the Core VR continues to operate in this mode. 111 +80% mΩ change 25:26 Offset trim [1:0] 27 Acknowledge bit FN8410 Rev 1.00 November 19, 2015 Page 25 of 37 ISL62773A Dynamic Offset Trim Protection Features The ISL62773A supports the SVI 2 ability for the processor to manipulate the output voltage offset of the Core and Northbridge VRs. This offset is in addition to any output voltage offset set via the COMP resistor reader. The dynamic offset trim can disable the COMP resistor programmed offset of either output when Disable All Offset is selected. Core VR and Northbridge VR both provide overcurrent, current-balance, undervoltage and overvoltage fault protections. The controller also provides over-temperature protection. The following discussion is based on Core VR and also applies to the Northbridge VR. TABLE 11. OFFSET TRIM DEFINITION OFFSET TRIM [1:0] DESCRIPTION 00 Disable all offset 01 -25mV change 10 0mV change 11 +25mV change Telemetry The ISL62773A can provide voltage and current information to the AMD CPU through the telemetry system outlined by the AMD SVI 2 specification. The telemetry data is transmitted through the SVC and SVT lines of the SVI 2 interface. Current telemetry is based on a voltage generated across a 133kΩ resistor placed from the IMON pin to GND. The current flowing out of the IMON pin is proportional to the load current in the VR. The Isum current defined in “Voltage Regulation and Load Line Implementation” on page 16, provides the base conversion from the load current to the internal amplifier created Isum current. The Isum current is then divided down by a factor of 4 to create the IMON current which flows out of the IMON pin. The Isum current will measure 35µA when the load current is at full load based on a droop current designed for 45µA at the same load current. The difference between the Isum current and the droop current is provided in Equation 2. The IMON current will measure 11.25µA at full load current for the VR and the IMON voltage will be 1.2V. The load percentage which is reported by the IC is based on the this voltage. When the load is 25% of the full load, the voltage on the IMON pin will be 25% of 1.2V or 0.3V. The SVI interface allows the selection of no telemetry, voltage only, or voltage and current telemetry on either or both of the VR outputs. The TFN bit along with the Core and Northbridge domain selector bits are used by the processor to change the functionality of telemetry; see Table 12 for more information. TABLE 12. TFN TRUTH TABLE TFN, CORE, NB BITS [21,6,7] DESCRIPTION 1,0,1 Telemetry is in voltage and current mode. Therefore, voltage and current are sent for VDD and VDDNB domains by the controller. 1,0,0 Telemetry is in voltage mode only. Only the voltage of VDD and VDDNB domains is sent by the controller. 1,1,0 Telemetry is disabled. 1,1,1 Reserved FN8410 Rev 1.00 November 19, 2015 Overcurrent The IMON voltage provides a means of determining the load current at any moment in time. The Overcurrent Protection (OCP) circuitry monitors the IMON voltage to determine when a fault occurs. Based on the previous description in “Voltage Regulation and Load Line Implementation” on page 16, the current which flows out of the IMON pin is proportional to the Isum current. The Isum current is created from the sensed voltage across Cn, which is a measure of the load current based upon the sensing element selected. The IMON current is generated internally and is 1/4 of the Isum current. The EDC or IDDspike current value for the AMD CPU load is used to set the maximum current level for droop and the IMON voltage of 1.2V which indicates 100% loading for telemetry. The Isum current level at maximum load, or IDDspike, is 36µA and this translates to an IMON current level of 9µA. The IMON resistor is 133kΩ and the 9µA flowing through the IMON resistor results in a 1.2V level at maximum loading of the VR. The overcurrent threshold is 1.5V on the IMON pin. Based on a 1.2V IMON voltage equating to 100% loading, the additional 0.3V provided above this level equates to a 25% increase in load current before an OCP fault is detected. The EDC or IDDspike current is used to set the 1.2V on IMON for full load current. So the OCP level is 1.25 times the EDC or IDDspike current level. This additional margin above the EDC or IDDspike current allows the AMD CPU to enter and exit the IDDspike performance mode without issue unless the load current is out of line with the IDDspike expectation, thus the need for overcurrent protection. When the voltage on the IMON pin meets the overcurrent threshold of 1.5V, this triggers an OCP event. Within 2µs of detecting an OCP event, the controller asserts VR_HOT_L low to communicate to the AMD CPU to throttle back. A fault timer begins counting while IMON is at or above the 1.5V threshold. The fault timer lasts 7.5µs to 11µs and then flags an OCP fault. The controller then tri-states the active channels and goes into shutdown. PGOOD is taken low and a fault flag from this VR is sent to the other VR and it is shut down within 10µs. If the IMON voltage drops below the 1.5V threshold prior to the fault timer count finishing, the fault timer is cleared and VR_HOT_L is taken high. The ISL62773A also features a Way-Overcurrent [WOC] feature which immediately takes the controller into shutdown. This protection is also referred to as fast overcurrent protection for short-circuit protection. If the IMON current reaches 15µA, WOC is triggered. Active channels are tri-stated and the controller is placed in shutdown and PGOOD is pulled low. There is no fault timer on the WOC fault, the controller takes immediate action. The other controller output is also shut down within 10µs. Page 26 of 37 ISL62773A Current-Balance The controller monitors the ISENx pin voltages to determine current-balance protection. If the ISENx pin voltage difference is greater than 9mV for 1ms, the controller will declare a fault and latch off. INTERNAL TO ISL62773A +V 30µA Undervoltage If the VSEN voltage falls below the output voltage VID value plus any programmed offsets by -325mV, the controller declares an undervoltage fault. The controller deasserts PGOOD and tri-states the power MOSFETs. Thermal Monitor [NTC, NTC_NB] The ISL62773A features two thermal monitors which use an external resistor network that includes an NTC thermistor to monitor motherboard temperature and alert the AMD CPU of a thermal issue. Figure 22 shows the basic thermal monitor circuit on the Core VR NTC pin. The Northbridge VR features the same thermal monitor. The controller drives a 30µA current out of the NTC pin and monitors the voltage at the pin. The current flowing out of the NTC pin creates a voltage that is compared to a warning threshold of 640mV. When the voltage at the NTC pin falls to this warning threshold or below, the controller asserts VR_HOT_L to alert the AMD CPU to throttle back load current to stabilize the motherboard temperature. A thermal fault counter begins counting toward a minimum shutdown time of 100µs. The thermal fault counter is an up/down counter, so if the voltage at the NTC pin rises above the warning threshold, it will count down and extend the time for a thermal fault to occur. The warning threshold does have 20mV of hysteresis. If the voltage at the NTC pin continues to fall down to the shutdown threshold of 580mV or below, the controller goes into shutdown and triggers a thermal fault. The PGOOD pin is pulled low and tri-states the power MOSFETs. A fault on either side will shutdown both VRs. Rp MONITOR + VNTC - RNTC WARNING SHUTDOWN 580mV 640mV Rs FIGURE 22. CIRCUITRY ASSOCIATED WITH THE THERMAL MONITOR FEATURE OF THE ISL62773A As the board temperature rises, the NTC thermistor resistance decreases and the voltage at the NTC pin drops. When the voltage on the NTC pin drops below the over-temperature trip threshold, then VR_HOT is pulled low. The VR_HOT signal is used to change the CPU operation and decrease power consumption. With the reduction in power consumption by the CPU, the board temperature decreases and the NTC thermistor voltage rises. Once the over-temperature threshold is tripped and VR_HOT is taken low, the over-temperature threshold changes to the reset level. The addition of hysteresis to the over-temperature threshold prevents nuisance trips. Once both pin voltages exceed the over-temperature reset threshold, the pull-down on VR_HOT is released. The signal changes state and the CPU resumes normal operation. The over-temperature threshold returns to the trip level. Table 13 summarizes the fault protections. TABLE 13. FAULT PROTECTION SUMMARY FAULT TYPE FAULT DURATION BEFORE PROTECTION PROTECTION ACTION Overcurrent 7.5µs to 11.5µs Phase Current Unbalance 1ms FAULT RESET PWM tri-state, PGOOD latched low Way-Overcurrent (1.5xOC) Undervoltage -325mV Overvoltage +325mV NTC Thermal FN8410 Rev 1.00 November 19, 2015 R NTC Overvoltage If the VSEN voltage exceeds the output voltage VID value plus any programmed offsets by +325mV, the controller declares an overvoltage fault. The controller deasserts PGOOD and turns on the low-side power MOSFETs. The low-side power MOSFETs remain on until the output voltage is pulled down below the VID set value. Once the output voltage is below this level, the lower gate is tri-stated. If the output voltage rises above the overvoltage threshold again, the protection process is repeated. when all power MOSFETs are turned off. This behavior provides the maximum amount of protection against shorted high-side power MOSFETs while preventing output ringing below ground. VR_HOT_L PGOOD latched low. PWM tri-state. Immediately 100µs min. PGOOD latched low. Actively pulls the output voltage to below VID value, then tri-state. ENABLE toggle or VDD toggle PGOOD latched low. PWM tri-state. Page 27 of 37 ISL62773A Fault Recovery All of the previously described fault conditions can be reset by bringing ENABLE low or by bringing VDD below the POR threshold. When ENABLE and VDD return to their high operating levels, the controller resets the faults and soft-start occurs. Interface Pin Protection The SVC and SVD pins feature protection diodes which must be considered when removing power to VDD and VDDIO, but leaving it applied to these pins. Figure 23 shows the basic protection on the pins. If SVC and/or SVD are powered but VDD is not, leakage current will flow from these pins to VDD. VDD SVC, SVD GND FIGURE 23. PROTECTION DEVICES ON THE SVC AND SVD PINS Key Component Selection Inductor DCR Current-Sensing Network PHASE1 PHASE2 PHASE3 RSUM RSUM ISUM+ RSUM L L RNTCS + RP DCR DCR DCR RNTC RO CNVCN RI ISUM- RO RO IO FIGURE 24. DCR CURRENT-SENSING NETWORK Figure 24 shows the inductor DCR current-sensing network for a 3-phase solution. An inductor current flows through the DCR and creates a voltage drop. Each inductor has two resistors in Rsum FN8410 Rev 1.00 November 19, 2015 The inductor output side pads are electrically shorted in the schematic but have some parasitic impedance in actual board layout, which is why one cannot simply short them together for the current-sensing summing network. It is recommended to use 1Ω~10Ω Ro to create quality signals. Since Ro value is much smaller than the rest of the current sensing circuit, the following analysis ignores it. The summed inductor current information is presented to the capacitor Cn. Equations 18 through 22 describe the frequency domain relationship between inductor total current Io(s) and Cn voltage VCn(s): INTERNAL TO ISL62773A L and Ro connected to the pads to accurately sense the inductor current by sensing the DCR voltage drop. The Rsum and Ro resistors are connected in a summing network as shown, and feed the total current information to the NTC network (consisting of Rntcs, Rntc and Rp) and capacitor Cn. Rntc is a negative temperature coefficient (NTC) thermistor, used to temperature compensate the inductor DCR change. R ntcnet DCR V Cn s = ------------------------------------------ ------------- I o s A cs s R sum N R ntcnet + ------------- N (EQ. 18) R ntcs + R ntc R p R ntcnet = ---------------------------------------------------R ntcs + R ntc + R p (EQ. 19) s 1 + ------L A cs s = ----------------------s 1 + ------------ sns (EQ. 20) DCR L = ------------L (EQ. 21) 1 sns = -------------------------------------------------------R sum R ntcnet --------------N ----------------------------------------- Cn R sum R ntcnet + --------------N (EQ. 22) Where N is the number of phases. Transfer function Acs(s) always has unity gain at DC. The inductor DCR value increases as the winding temperature increases, giving higher reading of the inductor DC current. The NTC Rntc value decrease as its temperature decreases. Proper selection of Rsum, Rntcs, Rp and Rntc parameters ensures that VCn represents the inductor total DC current over the temperature range of interest. There are many sets of parameters that can properly temperature-compensate the DCR change. Since the NTC network and the Rsum resistors form a voltage divider, Vcn is always a fraction of the inductor DCR voltage. It is recommended to have a higher ratio of Vcn to the inductor DCR voltage so the droop circuit has a higher signal level to work with. A typical set of parameters that provide good temperature compensation are: Rsum = 3.65kΩ, Rp = 11kΩ, Rntcs = 2.61kΩ and Rntc = 10kΩ (ERT-J1VR103J). The NTC network parameters may need to be fine tuned on actual boards. One can apply full load DC current and record the output voltage reading Page 28 of 37 ISL62773A immediately; then record the output voltage reading again when the board has reached the thermal steady state. A good NTC network can limit the output voltage drift to within 2mV. It is recommended to follow the Intersil evaluation board layout and current sensing network parameters to minimize engineering time. VCn(s) also needs to represent real-time Io(s) for the controller to achieve good transient response. Transfer function Acs(s) has a pole wsns and a zero wL. One needs to match wL and wsns so Acs(s) is unity gain at all frequencies. By forcing wL equal to wsns and solving for the solution, Equation 23 gives Cn value. L C n = --------------------------------------------------------------R sum R ntcnet --------------N ------------------------------------------ DCR R sum R ntcnet + --------------N io Vo FIGURE 27. LOAD TRANSIENT RESPONSE WHEN Cn IS TOO LARGE io (EQ. 23) Vo For example, given N = 3, Rsum = 3.65kΩ, Rp = 11kΩ, Rntcs = 2.61kΩ, Rntc = 10kΩ, DCR = 0.88mΩ and L = 0.36µH, Equation 23 gives Cn = 0.406µF. Assuming the compensator design is correct, Figure 25 shows the expected load transient response waveforms if Cn is correctly selected. When the load current Icore has a square change, the output voltage Vcore also has a square response. If Cn value is too large or too small, VCn(s) does not accurately represent real-time Io(s) and worsens the transient response. Figure 26 shows the load transient response when Cn is too small. Vcore sags excessively upon load insertion and may create a system failure. Figure 27 shows the transient response when Cn is too large. Vcore is sluggish in drooping to its final value. There is excessive overshoot if load insertion occurs during this time, which may negatively affect the CPU reliability. iL RING BACK FIGURE 28. OUTPUT VOLTAGE RINGBACK PROBLEM ISUM+ R ntcs C n.1 Cn.2 Rp Rntc Vcn Rn OPTIONAL ISUM- Ri io Rip C ip OPTIONAL Vo FIGURE 25. DESIRED LOAD TRANSIENT RESPONSE WAVEFORMS io Vo FIGURE 26. LOAD TRANSIENT RESPONSE WHEN Cn IS TOO SMALL FN8410 Rev 1.00 November 19, 2015 FIGURE 29. OPTIONAL CIRCUITS FOR RINGBACK REDUCTION Figure 28 shows the output voltage ringback problem during load transient response. The load current io has a fast step change, but the inductor current iL cannot accurately follow. Instead, iL responds in first-order system fashion due to the nature of the current loop. The ESR and ESL effect of the output capacitors makes the output voltage Vo dip quickly upon load current change. However, the controller regulates Vo according to the droop current idroop, which is a real-time representation of iL; therefore, it pulls Vo back to the level dictated by iL, causing the ringback problem. This phenomenon is not observed when the output capacitor has very low ESR and ESL, as is the case with all ceramic capacitors. Figure 29 shows two optional circuits for reduction of the ring-back. Cn is the capacitor used to match the inductor time constant. It usually takes the parallel of two (or more) capacitors to get the desired value. Figure 29 shows that two capacitors (Cn.1 and Cn.2) are in parallel. Resistor Rn is an optional component to reduce the Vo ringback. At steady state, Page 29 of 37 ISL62773A Cn.1 + Cn.2 provides the desired Cn capacitance. At the beginning of io change, the effective capacitance is less because Rn increases the impedance of the Cn.1 branch. As Figure 26 shows, Vo tends to dip when Cn is too small, and this effect reduces the Vo ring-back. This effect is more pronounced when Cn.1 is much larger than Cn.2. It is also more pronounced when Rn is bigger. However, the presence of Rn increases the ripple of the Vn signal if Cn.2 is too small. It is recommended to keep Cn.2 greater than 2200pF. Rn value usually is a few ohms. Cn.1, Cn.2 and Rn values should be determined through tuning the load transient response waveforms on an actual board. Rip and Cip form an R-C branch in parallel with Ri, providing a lower impedance path than Ri at the beginning of io change. Rip and Cip do not have any effect at steady state. Through proper selection of Rip and Cip values, idroop can resemble io rather than iL, and Vo will not ring back. The recommended value for Rip is 100Ω. Cip should be determined through tuning the load transient response waveforms on an actual board. The recommended range for Cip is 100pF~2000pF. However, it should be noted that the Rip - Cip branch may distort the idroop waveform. Instead of being triangular as the real inductor current, idroop may have sharp spikes, which may adversely affect idroop average value detection and therefore may affect OCP accuracy. User discretion is advised. Resistor Current-Sensing Network L L DCR DCR DCR RSUM RSEN VCN RO (EQ. 25) 1 Rsen = ----------------------------R sum --------------- C n N (EQ. 26) Transfer function ARsen(s) always has unity gain at DC. Current-sensing resistor Rsen value does not have significant variation over-temperature, so there is no need for the NTC network. The recommended values are Rsum = 1kΩ and Cn = 5600pF. Overcurrent Protection Refer to Equation 2 on page 17 and Figures 24, 28 and 30; resistor Ri sets the Isum current which is proportional to droop current and IMON current. Tables 1 and 2 show the internal OCP threshold based on the IMON pin voltage. Since the Ri resistor impacts both the droop current and the IMON current, fine adjustments to Idroop will require changing the Rcomp resistor. ISUM+ R ntcnet DCR V Cn = ------------------------------------------ ------------- I o N R sum R ntcnet + ------------- N ISUM- Substitution of Equation 27 into Equation 2 gives Equation 28: RSUM RSEN 1 A Rsen s = ----------------------s 1 + ------------ sns For inductor DCR sensing, Equation 27 gives the DC relationship of Vcn(s) and Io(s): RSUM RSEN (EQ. 24) For example, the OCP threshold is 1.5V on the IMON pin which equates to an IMON current of 11.25µA using a 133kΩ IMON resistor. The corresponding Isum is 45µA which results in an Idroop of 56.25µA. At full load current, Iomax, the Isum current is 36µA and the resulting Idroop is 45µA. The ratio of Isum at OCP relative to full load current is 1.25. Therefore, the OCP current trip level is 25% higher than the full load current. PHASE1 PHASE2 PHASE3 L R sen V Cn s = ------------- I o s A Rsen s N + - Cn Ri RO RO (EQ. 27) R ntcnet DCR 5 1 I droop = --- ----- ------------------------------------------ ------------- I o R sum N 4 Ri R ntcnet + --------------N (EQ. 28) Therefore: IO FIGURE 30. RESISTOR CURRENT-SENSING NETWORK Figure 30 shows the resistor current-sensing network for a 3-phase solution. Each inductor has a series current sensing resistor, Rsen. Rsum and Ro are connected to the Rsen pads to accurately capture the inductor current information. The Rsum and Ro resistors are connected to capacitor Cn. Rsum and Cn form a filter for noise attenuation. Equations 24 through 26 give the VCn(s) expression. R ntcnet DCR I o 5 R i = --- ---------------------------------------------------------------------------------R sum 4 N R ntcnet + --------------- I droop N (EQ. 29) Substitution of Equation 19 and application of the OCP condition in Equation 29 gives Equation 30: R ntcs + R ntc R p ---------------------------------------------------- DCR I omax R ntcs + R ntc + R p 5 R i = --- ----------------------------------------------------------------------------------------------------------------------------4 R ntcs + R ntc R p R sum N ---------------------------------------------------- + --------------- I droopmax N R ntcs + R ntc + R p (EQ. 30) Where Iomax is the full load current and Idroopmax is the corresponding droop current. For example, given N = 3, Rsum = 3.65kΩ, Rp = 11kΩ, Rntcs = 2.61kΩ, Rntc = 10kΩ, FN8410 Rev 1.00 November 19, 2015 Page 30 of 37 ISL62773A DCR = 0.88mΩ, Iomax = 65A and Idroopmax = 45μA. Equation 30 gives Ri = 439Ω. For resistor sensing, Equation 31 gives the DC relationship of Vcn(s) and Io(s). R sen V Cn = ------------- I o N (EQ. 31) Substitution of Equations 31 into Equation 2 gives Equation 32: 5 1 R sen I droop = --- ----- ------------- I o N 4 Ri Compensator Figure 25 on page 29 shows the desired load transient response waveforms. Figure 31 shows the equivalent circuit of a voltage regulator (VR) with the droop function. A VR is equivalent to a voltage source (= VID) and output impedance Zout(s). If Zout(s) is equal to the load line slope LL, i.e., a constant output impedance, then in the entire frequency range, Vo will have a square response when Io has a square change. (EQ. 32) Therefore: 5 R sen I o R i = --- --------------------------4 N I droop (EQ. 34) Load Line Slope See Figure 16 for load-line implementation. For inductor DCR sensing, substitution of Equation 28 into Equation 3 gives the load-line slope expression: o (EQ. 35) Intersil provides a Microsoft Excel-based spreadsheet to help design the compensator and the current sensing network so that VR achieves constant output impedance as a stable system. A VR with active droop function is a dual-loop system consisting of a voltage loop and a droop loop, which is a current loop. However, neither loop alone is sufficient to describe the entire system. The spreadsheet shows two loop gain transfer functions, T1(s) and T2(s), that describe the entire system. Figure 32 conceptually shows T1(s) measurement setup and Figure 33 conceptually shows T2(s) measurement setup. The VR senses the inductor current, multiplies it by a gain of the load line slope, adds it on top of the sensed output voltage and then feeds it to the compensator. T1 is measured after the summing node, and T2 is measured in the voltage loop before the summing node. The spreadsheet gives both T1(s) and T2(s) plots. However, only T2(s) can actually be measured on an ISL62773A regulator. (EQ. 36) Q1 VIN GATE DRIVER Q2 It is recommended to start with the Rdroop value calculated by Equation 37 and fine-tune it on the actual board to get accurate load-line slope. One should record the output voltage readings at no load and at full load for load line slope calculation. Reading the output voltage at lighter load instead of full load will increase the measurement error. iO COUT LOAD LINE SLOPE 20 EA MOD. (EQ. 37) One can use the full-load condition to calculate Rdroop. For example, given Iomax = 65A, Idroopmax = 45µA and LL = 2.1mΩ, Equation 37 gives Rdroop = 3.03kΩ. VO L Substitution of Equation 29 and rewriting Equaion Equation 35, or substitution of Equation 33 and rewriting Equation 36, gives the same result as in Equation 37: Io R droop = ---------------- LL I droop V FIGURE 31. VOLTAGE REGULATOR EQUIVALENT CIRCUIT For resistor sensing, substitution of Equation 32 into Equation 3 gives the load line slope expression: V droop 5 R sen R droop LL = ------------------- = --- --------------------------------------Io 4 N Ri LOAD (EQ. 33) Where Iomax is the full load current and Idroopmax is the corresponding droop current. For example, given N = 3, Rsen = 1mΩ, Iomax = 65A and Idroopmax = 45µA, Equation 34 gives Ri = 602Ω. V droop R ntcnet 5 R droop DCR LL = ------------------- = --- ------------------- ------------------------------------------ ------------4 N Io Ri R sum R ntcnet + --------------N o VR VID Substitution of Equation 33 and application of the OCP condition in Equation 29 gives Equation 34: 5 R sen I omax R i = --- -------------------------------------4 N I droopmax i Zout(s) = LL COMP + VID + + ISOLATION TRANSFORMER CHANNEL B LOOP GAIN = CHANNEL A CHANNEL A NETWORK ANALYZER CHANNEL B EXCITATION OUTPUT FIGURE 32. LOOP GAIN T1(s) MEASUREMENT SETUP T1(s) is the total loop gain of the voltage loop and the droop loop. It always has a higher crossover frequency than T2(s), therefore has a higher impact on system stability. T2(s) is the voltage loop gain with closed droop loop, thus having a higher impact on output voltage response. FN8410 Rev 1.00 November 19, 2015 Page 31 of 37 ISL62773A Design the compensator to get stable T1(s) and T2(s) with sufficient phase margin and an output impedance equal to or smaller than the load line slope. L VO Q1 VIN GATE Q2 DRIVER IO CO If the board temperature continues to rise, the NTC thermistor resistance will drop further and the voltage at the NTC pin could drop below the thermal shutdown threshold of 0.580V. Once this threshold is reached, the ISL62773A shuts down both Core and Northbridge VRs indicating a thermal fault has occurred prior to the thermal fault counter triggering a fault. LOAD LINE SLOPE EA MOD. + COMP LOOP GAIN = + + - 20 VID ISOLATION TRANSFORMER CHANNEL B CHANNEL A CHANNEL A CHANNEL B NETWORK ANALYZER FIGURE 33. LOOP GAIN T2(s) MEASUREMENT SETUP Current Balancing Refer to Figures 17 through 24 for information on current balancing. The ISL62773A achieves current balancing through matching the ISEN pin voltages. Risen and Cisen form filters to remove the switching ripple of the phase node voltages. It is recommended to use a rather long RisenCisen time constant such that the ISEN voltages have minimal ripple and represent the DC current flowing through the inductors. Recommended values are Rs = 10kΩ and Cs = 0.22µF. Thermal Monitor Component Selection The ISL62773A features two pins, NTC and NTC_NB, which are used to monitor motherboard temperature and alert the AMD CPU if a thermal issues arises. The basic function of this circuitry is outlined in the Thermal Monitor section on page 27. Figure 34 shows the basic configuration of the NTC resistor, RNTC, and offset resistor, RS, used to generate the warning and shutdown voltages at the NTC pin. INTERNAL TO ISL62773A +V VR_HOT_L R NTC MONITOR 330kΩ 8.45kΩ RNTC Rs Selection of the NTC thermistor can vary depending on how the resistor network is configured. The equivalent resistance at the typical thermal warning threshold voltage of 0.64V is defined in Equation 38. 0.64V ---------------- = 21.3k 30A EXCITATION OUTPUT 30µA As the board temperature rises, the NTC thermistor resistance decreases and the voltage at the NTC pin drops. When the voltage on the NTC pin drops below the thermal warning threshold of 0.640V, then VR_HOT_L is pulled low. When the AMD CPU detects VR_HOT_L has gone low, it will begin throttling back load current on both outputs to reduce the board temperature. WARNING SHUTDOWN 640mV 580mV FIGURE 34. THERMAL MONITOR FEATURE OF THE ISL62773A (EQ. 38) The equivalent resistance at the typical thermal shutdown threshold voltage of 0.58V required to shut down both outputs is defined in Equation 39. 0.58V ---------------- = 19.3k 30A (EQ. 39) The NTC thermistor value correlates to the resistance change between the warning and shutdown thresholds and the required temperature change. If the warning level is designed to occur at a board temperature of +100°C and the thermal shutdown level at a board temperature of +105°C, then the resistance change of the thermistor can be calculated. For example, a Panasonic NTC thermistor with B = 4700 has a resistance ratio of 0.03939 of its nominal value at +100°C and 0.03308 of its nominal value at +105°C. Taking the required resistance change between the thermal warning threshold and the shutdown threshold and dividing it by the change in resistance ratio of the NTC thermistor at the two temperatures of interest, the required resistance of the NTC is defined in Equation 40. 21.3k – 19.3k ------------------------------------------------------ = 317k 0.03939 – 0.03308 (EQ. 40) The closest standard thermistor to the value calculated with B = 4700 is 330kΩ. The NTC thermistor part number is ERTJ0EV334J. The actual resistance change of this standard thermistor value between the warning threshold and the shutdown threshold is calculated in Equation 41. 330k 0.03939 – 330k 0.03308 = 2.082k (EQ. 41) Since the NTC thermistor resistance at +105°C is less than the required resistance from Equation 39, additional resistance in series with the thermistor is required to make up the difference. A standard resistor, 1% tolerance, added in series with the thermistor will increase the voltage seen at the NTC pin. The additional resistance required is calculated in Equation 42. (EQ. 42) 19.3k – 10.916k = 8.384k The closest, standard 1% tolerance resistor is 8.45kΩ. FN8410 Rev 1.00 November 19, 2015 Page 32 of 37 ISL62773A The NTC thermistor is placed in a hot spot on the board, typically near the upper MOSFET of Channel 1 of the respective output. The standard resistor is placed next to the controller. Bootstrap Capacitor Selection The integrated gate drivers feature an internal bootstrap Schottky diode. Simply adding an external capacitor across the BOOT and PHASE pins completes the bootstrap circuit. The bootstrap capacitor must have a maximum voltage rating above VDDP + 4V and its capacitance value can be chosen from Equation 43: Q GATE C BOOT_CAP -------------------------------------V BOOT_CAP (EQ. 43) Q G1 PVCC Q GATE = ------------------------------------ N Q1 V GS1 Where QG1 is the amount of gate charge per upper MOSFET at VGS1 gate-source voltage and NQ1 is the number of control MOSFETs. The VBOOT_CAP term is defined as the allowable droop in the rail of the upper gate drive. Optional FCCM_NB Filtering The option for the placement of a capacitor in parallel with the resistor from the FCCM_NB pin to GND is recommend. In the event of a poor layout and excessive noise found on the FCCM_NB pin, this capacitor can be populated to reduce the noise on the pin and prevent it from corrupting the resistor read portion of the soft-start sequence. Layout Guidelines PCB Layout Considerations POWER AND SIGNAL LAYERS PLACEMENT ON THE PCB As a general rule, power layers should be close together, either on the top or bottom of the board, with the weak analog or logic signal layers on the opposite side of the board. The ground-plane layer should be adjacent to the signal layer to provide shielding. COMPONENT PLACEMENT There are two sets of critical components in a DC/DC converter; the power components and the small signal components. The power components are the most critical because they switch large amount of energy. The small signal components connect to sensitive nodes or supply critical bypassing current and signal coupling. The power components should be placed first and these include MOSFETs, input and output capacitors, and the inductor. It is important to have a symmetrical layout for each power train, preferably with the controller located equidistant from each power train. Symmetrical layout allows heat to be dissipated equally across all power trains. Keeping the distance between the power train and the control IC short helps keep the gate drive traces short. These drive signals include the LGATE, UGATE, PGND, PHASE and BOOT. VIAS TO GROUND PLANE GND VOUT INDUCTOR OUTPUT CAPACITORS SCHOTTKY DIODE PHASE NODE HIGH-SIDE MOSFETs VIN LOW-SIDE MOSFETs INPUT CAPACITORS FIGURE 35. TYPICAL POWER COMPONENT PLACEMENT When placing MOSFETs, try to keep the source of the upper MOSFETs and the drain of the lower MOSFETs as close as thermally possible (see Figure 35). Input high-frequency capacitors should be placed close to the drain of the upper MOSFETs and the source of the lower MOSFETs. Place the output inductor and output capacitors between the MOSFETs and the load. High-frequency output decoupling capacitors (ceramic) should be placed as close as possible to the decoupling target (microprocessor), making use of the shortest connection paths to any internal planes. Place the components in such a way that the area under the IC has less noise traces with high dV/dt and di/dt, such as gate signals and phase node signals. Table 14 shows layout considerations for the ISL62773A controller by pin. TABLE 14. LAYOUT CONSIDERATIONS FOR THE ISL62773A CONTROLLER ISL62773A PIN SYMBOL BOTTOM PAD GND 1 ISEN2_NB Each ISEN pin has a capacitor (Cisen) decoupling it to VSUMN_NB, then through another capacitor (Cvsumn_nb) to GND. Place Cisen capacitors as close as possible to the controller and keep the following loops small: 1. ISEN1_NB pin to ISEN2_NB pin 2. Any ISENx_NB pin to GND 2 NTC_NB The NTC thermistor must be placed close to the thermal source that is monitored to determine Northbridge thermal throttling. Placement at the hottest spot of the Northbridge VR is recommended. Additional standard resistors in the resistor network on this pin should be placed near the IC. 3 IMON_NB 4 SVC FN8410 Rev 1.00 November 19, 2015 LAYOUT GUIDELINES Connect this ground pad to the ground plane through a low impedance path. A minimum of 5 vias are recommended to connect this pad to the internal ground plane layers of the PCB Place the IMON_NB resistor close to this pin and keep a tight GND connection. Use good signal integrity practices and follow AMD recommendations. Page 33 of 37 ISL62773A TABLE 14. LAYOUT CONSIDERATIONS FOR THE ISL62773A CONTROLLER (Continued) ISL62773A PIN SYMBOL LAYOUT GUIDELINES 5 VR_HOT_L 6 SVD 7 VDDIO 8 SVT 9 ENABLE No special considerations. 10 PWROK Use good signal integrity practices and follow AMD recommendations. 11 IMON 12 NTC The NTC thermistor must be placed close to the thermal source that is monitored to determine Core thermal throttling. Placement at the hottest spot of the Core VR is recommended. Additional standard resistors in the resistor network on this pin should be placed near the IC. 13 ISEN3 14 ISEN2 Each ISEN pin has a capacitor (Cisen) decoupling it to VSUMN and then through another capacitor (Cvsumn) to GND. Place Cisen capacitors as close as possible to the controller and keep the following loops small: 1. Any ISEN pin to another ISEN pin 15 ISEN1 Follow AMD recommendations. Placement of the pull-up resistor near the IC is recommended. Use good signal integrity practices and follow AMD recommendations. Place the IMON resistor close to this pin and keep a tight GND connection. 2. Any ISEN pin to GND The red traces in the following drawing show the loops to be minimized. Phase1 L3 Ro R isen ISEN3 C isen Phase2 Vo L2 Ro R isen ISEN2 C isen Phase3 R isen ISEN1 GND ISUMP 17 ISUMN Ro V vsumn C isen 16 L1 C vsumn Place the current sensing circuit in general proximity of the controller. Place capacitor Cn very close to the controller. Place the NTC thermistor next to Core VR Channel 1 inductor so it senses the inductor temperature correctly. Each phase of the power stage sends a pair of VSUMP and VSUMN signals to the controller. Run these two signals traces in parallel fashion with decent width (>20mil). IMPORTANT: Sense the inductor current by routing the sensing circuit to the inductor pads. If possible, route the traces on a different layer from the inductor pad layer and use vias to connect the traces to the center of the pads. If no via is allowed on the pad, consider routing the traces into the pads from the inside of the inductor. The following drawings show the two preferred ways of routing current sensing traces. INDUCTOR INDUCTOR VIAS CURRENT-SENSING TRACES 18 VSEN 19 RTN FN8410 Rev 1.00 November 19, 2015 CURRENT-SENSING TRACES Place the filter on these pins in close proximity to the controller for good coupling. Page 34 of 37 ISL62773A TABLE 14. LAYOUT CONSIDERATIONS FOR THE ISL62773A CONTROLLER (Continued) ISL62773A PIN SYMBOL 20 FB2 21 FB 22 COMP 23 PGOOD No special consideration. 24 BOOT1 Use a wide trace width (>30mil). Avoid routing any sensitive analog signal traces close to or crossing over this trace. 25 UGATE1 26 PHASE1 These two signals should be routed together in parallel. Each trace should have sufficient width (>30mil). Avoid routing these signals near sensitive analog signal traces or crossing over them. Routing PHASE1 to the Core VR Channel 1 high-side MOSFET source pin instead of a general connection to PHASE1 copper is recommended for better performance. 27 LGATE1 Use sufficient trace width (>30mil). Avoid routing this signal near any sensitive analog signal traces or crossing over them. 28 PWM_Y No special considerations. 29 VDD A high quality, X7R dielectric MLCC capacitor is recommended to decouple this pin to GND. Place the capacitor in close proximity to the pin with the filter resistor nearby the IC. 30 VDDP A high quality, X7R dielectric MLCC capacitor is recommended to decouple this pin to GND. Place the capacitor in close proximity to the pin. 31 LGATE2 Use sufficient trace width (>30mil). Avoid routing this signal near any sensitive analog signal traces or crossing over them. 32 PHASE2 33 UGATE2 These two signals should be routed together in parallel. Each trace should have sufficient width (>30mil). Avoid routing these signals near sensitive analog signal traces or crossing over them. Routing PHASE2 to the Core VR Channel 2 high-side MOSFET source pin instead of a general connection to PHASE2 copper is recommended for better performance. 34 BOOT2 Use a wide trace width (>30mil). Avoid routing any sensitive analog signal traces close to or crossing over this trace. 35 VIN Place the decoupling capacitor in close proximity to the pin with a short connection to the internal GND plane. 36 BOOTX Use a wide trace width (>30mil). Avoid routing any sensitive analog signal traces close to or crossing over this trace. 37 UGATEX 38 PHASEX These two signals should be routed together in parallel. Each trace should have sufficient width (>30mil). Avoid routing these signals near sensitive analog signal traces or crossing over them. Routing PHASEX to the high-side MOSFET source pin instead of a general connection to the PHASEX copper is recommended for better performance. 39 LGATEX 40 PWM2_NB 41 FCCM_NB 42 PGOOD_NB 43 COMP_NB 44 FB_NB 45 VSEN_NB FN8410 Rev 1.00 November 19, 2015 LAYOUT GUIDELINES Place the compensation components in general proximity of the controller. Use sufficient trace width (>30mil). Avoid routing this signal near any sensitive analog signal traces or crossing over them. No special considerations. No special consideration. Place the compensation components in general proximity of the controller. Place the filter on this pin in close proximity to the controller for good coupling. Page 35 of 37 ISL62773A TABLE 14. LAYOUT CONSIDERATIONS FOR THE ISL62773A CONTROLLER (Continued) ISL62773A PIN SYMBOL LAYOUT GUIDELINES 46 ISUMN_NB 47 ISUMP_NB Place the current sensing circuit in general proximity of the controller. Place capacitor Cn very close to the controller. Place the NTC thermistor next to Core VR Channel 1 inductor so it senses the inductor temperature correctly. Each phase of the power stage sends a pair of VSUMP and VSUMN signals to the controller. Run these two signals traces in parallel fashion with decent width (>20mil). IMPORTANT: Sense the inductor current by routing the sensing circuit to the inductor pads. If possible, route the traces on a different layer from the inductor pad layer and use vias to connect the traces to the center of the pads. If no via is allowed on the pad, consider routing the traces into the pads from the inside of the inductor. The following drawings show the two preferred ways of routing current sensing traces. INDUCTOR INDUCTOR VIAS CURRENT-SENSING TRACES 48 CURRENT-SENSING TRACES ISEN1_NB Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION CHANGE November 19, 2015 FN8410.1 On page 1 under Features, added "Serial VID clock frequency range 100kHz to 25MHz" below "Supports AMD SVI 2.0 serial data bus interface”. Updated About Intersil verbiage. January 25, 2013 FN8410.0 Initial Release About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support. © Copyright Intersil Americas LLC 2013-2015. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN8410 Rev 1.00 November 19, 2015 Page 36 of 37 ISL62773A Package Outline Drawing L48.6x6B 48 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 0, 9/09 4X 4.4 6.00 44X 0.40 A B 6 PIN 1 INDEX AREA 6 PIN #1 INDEX AREA 48 37 1 6.00 36 4 .40 ± 0.15 25 12 0.15 (4X) 13 24 0.10 M C A B 0.05 M C TOP VIEW 48X 0.45 ± 0.10 4 48X 0.20 BOTTOM VIEW SEE DETAIL "X" 0.10 C BASE PLANE MAX 1.00 ( SEATING PLANE 0.08 C ( 44 X 0 . 40 ) ( 5. 75 TYP ) C SIDE VIEW 4. 40 ) C 0 . 2 REF 5 ( 48X 0 . 20 ) ( 48X 0 . 65 ) 0 . 00 MIN. 0 . 05 MAX. DETAIL "X" TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal ± 0.05 4. Dimension applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 indentifier may be either a mold or mark feature. FN8410 Rev 1.00 November 19, 2015 Page 37 of 37