MFU100 SERIES DC/DC CONVERTER 1W FEATURES ►Miniature DIP-Package with Industry Standard Pinout ►Package Dimension: 12.7 x 7.0 x 10.2 mm (0.50”x 0.28”x 0.40” inches) ►High I/O-Isolation 3000 VDC ►Operating Temp. Range -40°C to +85°C ►3 Years Product Warranty PRODUCT OVERVIEW The MINMAX MFU100 series is a range of 1W DC/DC converters in a miniature DIP Package featuring I/O-isolation of 3000VDC. A high efficiency allows an operating temperature range of –40°C to +85°C. These converters offer an economical solution for many space critical applications where a voltage has to be isolated i.e for noise reduction, ground loop elimination, digital interfaces or for board level power distribution. Model Selection Guide Model Input Output Number Voltage Voltage (Range) VDC MFU102 MFU103 MFU104 MFU105 MFU112 MFU113 MFU114 MFU115 MFU122 MFU123 MFU124 MFU125 5 (4.5 ~ 5.5) 12 (10.8 ~ 13.2) 24 (21.6 ~ 26.4) VDC 5 9 12 15 5 9 12 15 5 9 12 15 Output Current Input Current Max. Min. @Max. Load @No Load mA 200 110 84 67 200 110 84 67 200 110 84 67 mA 4 2 1.5 1 4 2 1.5 1 4 2 1.5 1 mA(typ.) 290 260 262 257 117 107 106 106 60 54 53 53 mA(typ.) Load Max. capacitive Regulation Load Efficiency (typ.) @Max. Load % (max.) 11 8 7 6 9 5 5 4 8 5 4 4 30 13 10 uF 33 33 33 % 69 76 77 78 71 77 79 79 70 76 79 79 # For each output Input Specifications Parameter Model Input Voltage Range Input Surge Voltage (1 sec. max.) 4.5 5 5.5 10.8 12 13.2 24V Input Models 21.6 24 26.4 5V Input Models -0.7 --- 7 12V Input Models -0.7 --- 15 24V Input Models -0.7 --- 28 --- --- 0.3 Internal Power Dissipation Tel:886-6-2923150 Page 1 of 4 Unit VDC A Internal Capacitor --- E-mail:[email protected] Max. 5V Input Models All Models Input Filter Typ. 12V Input Models Reverse Polarity Input Current 2012/01/09 REV:6 Min. --- 450 mW MFU100 SERIES DC/DC CONVERTER 1W Output Specifications Parameter Conditions Min. Typ. Max. --- ±1.0 ±3.0 % --- ±1.2 ±1.5 % Output Voltage Accuracy Line Regulation For Vin Change of 1% Load Regulation Io=20% to 100% Ripple & Noise (20MHz) Ripple & Noise (20MHz) Over Line, Load & Temp. Unit See Model Selection Guide --- 100 150 mV P-P --- --- 200 mV P-P Ripple & Noise (20MHz) --- --- 15 mV rms Temperature Coefficient --- ±0.01 ±0.02 %/℃ Short Circuit Protection 0.5 Second Max. General Specifications Parameter I/O Isolation Voltage (rated) Conditions Min. Typ. Max. Unit 60 Seconds 3000 --- --- VDC I/O Isolation Resistance 500 VDC 10 --- --- GΩ I/O Isolation Capacitance 100KHz, 1V --- 60 100 pF 50 90 110 KHz 2,000,000 --- --- Hours Switching Frequency MTBF (calculated) MIL-HDBK-217F@25℃, Ground Benign Input Fuse 5V Input Models 500mA Slow-Blow Type 12V Input Models 200mA Slow-Blow Type 24V Input Models 100mA Slow-Blow Type Environmental Specifications Parameter Operating Temperature Range (with Derating) Case Temperature Storage Temperature Range Humidity (non condensing) Cooling Lead Temperature (1.5mm from case for 10Sec.) Conditions Ambient Min. -40 ---50 --Free-Air convection --- Max. +85 +90 +125 95 Unit ℃ ℃ ℃ % rel. H 260 ℃ Power Derating Curve 100 100 Natural convection 80 Natural convection 80 100LFM 100LFM 200LFM 60 200LFM 60 400LFM 400LFM 40 40 20 20 0 0 ~ -40 0 20 40 60 80 100 110 Ambient Temperature ] (5V Output Only) ~ -40 0 20 40 60 80 100 110 Ambient Temperature ] (All Other Output) Notes 1 Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted. 2 Ripple & Noise measurement bandwidth is 0-20MHz. 3 These power converters require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage these 4 All DC/DC converters should be externally fused at the front end for protection. modules; however they may not meet all specifications listed. 5 Other input and output voltage may be available, please contact factory. 6 That “natural convection” is about 20LFM but is not equal to still air (0 LFM). 7 Specifications subject to change without notice. E-mail:[email protected] 2012/01/09 REV:6 Tel:886-6-2923150 Page 2 of 4 MFU100 SERIES DC/DC CONVERTER 1W Package Specifications Pin Connections 2.54 [0.10] 0.50 [0.02] 7.62 [0.30] Bottom View 7 5 -Vin 4 +Vin 5 +Vout 7 -Vout L=8.0 [0.31] for 24V Input Models 10.2 [0.40] 4 Function 1 L=7.0 [0.28] for 5V & 12V Input Models 2.6 [0.10] 7.62 [0.30] 1 Pin L 3.1 [0.12] 0.4 [0.02] Mechanical Dimensions 12.7 [0.50] 1.29 [0.05] ►All 5.08 [0.20] dimensions in mm (inches) ►Tolerance: X.X±0.25 ►Pin Physical Characteristics Case Size(5V&12V Input) : 12.7x7.0x10.2mm (0.50x0.28x0.40 Inches) Case Size(24V Input) : 12.7x8.0x10.2mm (0.50x0.31x0.40 Inches) Case Material : Non-Conductive Black Plastic (flammability to UL 94V-0 rated) Weight(5V&12V Input) : 1.3g Weight(24V Input) : 1.7g E-mail:[email protected] 2012/01/09 REV:6 Tel:886-6-2923150 Page 3 of 4 (X.XX±0.01) X.XX±0.13 ( X.XXX±0.005) diameter 0.5 ±0.05 (0.02±0.002) MFU100 SERIES DC/DC CONVERTER 1W Test Configurations Peak-to-Peak Output Noise Measurement Test Use a Cout 0.33uF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load between 50 mm and 75 mm from the DC/DC Converter. +Vin +Out Copper Strip Single Output DC / DC Converter -Vin Cout -Out Scope Resistive Load Copper Strip Design & Feature Considerations Maximum Capacitive Load The MFU100 series has limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up, affecting the ramp-up and the startup time. For optimum performance we recommend 33uF maximum capacitive load for devices. The maximum capacitance can be found in the data sheet.. Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup. Capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to use a good quality low Equivalent Series Resistance (ESR < 1.0Ω at 100 KHz) capacitor of a 1.5uF for the 5V input devices, a 1.0uF for the 12V input devices and a 0.47uF for the 24V devices. + DC Power Source +Vin + +Out DC / DC Converter Load Cin - -Vin -Out Output Ripple Reduction A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is recommended to use 1uF capacitors at the output. + +Vin DC Power Source - +Out Single Output DC / DC Converter -Vin Cout Load -Out Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90℃. The derating curves are determined from measurements obtained in a test setup. Position of air velocity probe and thermocouple 15mm / 0.6in 50mm / 2in Air Flow DUT 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] Minmax Technology Co., Ltd. 2012/01/09 REV:6 Page 4 of 4