Rohm BD8962MUV 2.7v to 5.5v, 3a 1ch synchronous buck converter integrated fet Datasheet

2.7V to 5.5V, 3A 1ch
Synchronous Buck Converter integrated FET
BD8962MUV
●General Description
ROHM’s high efficiency step-down switching regulator
BD8962MUV is a power supply designed to produce a
low voltage including 0.8 volts from 5.5/3.3 volts power
supply line. Offers high efficiency with synchronous
rectifier. Employs a current mode control system to
provide faster transient response to sudden change in
load.
●Key Specifications
 Input voltage range:
 Output voltage range:
 Average output Current:
 Switching frequency:
 Highside FET ON resistance:
 Lowsaide FET ON resistance:
 Standby current:
 Operating temperature range:
●Features
 Offers fast transient response with current mode
PWM control system.
 Offers highly efficiency for all load range with
synchronous rectifier (Nch/Nch FET)
 Incorporates soft-start function.
 Incorporates thermal protection and ULVO
functions.
 Incorporates short-current protection circuit with
time delay function.
 Incorporates shutdown function.
●Packages
VQFN020V4040
2.7V to 5.5V
0.8V to 2.5V
3.0A(Max.)
1MHz(Typ.)
82mΩ(Typ.)
70mΩ(Typ.)
0μA(Typ.)
-40℃ to +105℃
4.0mm x 4.0mm x 1.0mm
●Applications
Power supply for LSI including DSP, Micro computer
and ASIC
●Typical Application Circuit
Fig.1 Typical Application Circuit
○Product structure:Silicon monolithic integrated circuit
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
○This product is not designed protection against radioactive rays.
1/18
TSZ02201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
●Pin Configuration
N.C.
TOP VIEW
ITH
ADJ
GND
15 14 13 12 11
N.C.
16
10
VCC
EN
17
9
BST
18
8
19
7
20
6
PGND
1
2
3
4
PVCC
5
SW
Fig.2 Pin configuration
●Pin Description
Pin
No.
1
2
Pin
name
SW
SW
3
SW
4
5
6
7
8
9
10
SW
SW
PVCC
PVCC
PVCC
BST
VCC
SW pin
SW pin
Pin
No.
11
12
Pin
name
GND
ADJ
SW pin
13
ITH
SW pin
SW pin
Highside FET source pin
Highside FET source pin
Highside FET source pin
Bootstrapped voltage input pin
VCC power supply input pin
14
15
16
17
18
19
20
N.C.
N.C.
N.C.
EN
PGND
PGND
PGND
Function
Function
Ground
Output voltage detect pin
GmAmp output pin/Connected phase
compensation capacitor
Non Connection
Non Connection
Non Connection
Enable pin(High Active)
Lowside FET source pin
Lowside source pin
Lowside source pin
●Block Diagram
Fig.3 Block Diagram
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
2/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
●Absolute Maximum Ratings(Ta=25℃)
Parameter
Symbol
VCC
VCC Voltage
PVCC
PVCC Voltage
VBST
BST Voltage
V
BST
-SW
BST_SW Voltage
VEN
EN Voltage
VSW,
SW,ITH Voltage
VITH
Pd1
Power Dissipation 1
Pd2
Power Dissipation 2
Pd3
Power Dissipation 3
Pd4
Power Dissipation 4
Topr
Operating temperature range
Tstg
Storage temperature range
Tjmax
Maximum junction temperature
*1
*2
*3
*4
*5
Limit
1
-0.3 to +7 *
1
-0.3 to +7 *
-0.3 to +13
-0.3 to +7
-0.3 to +7
Units
V
V
V
-0.3 to +7
V
V
V
2
0.34 *
3
0.70 *
4
1.21 *
5
3.56 *
-40 to +105
-55 to +150
+150
W
W
W
W
℃
℃
℃
Pd should not be exceeded.
IC only
1-layer. mounted on a 74.2mm×74.2mm×1.6mm glass-epoxy board, occupied area by copper foil : 10.29mm2
4-layer. mounted on a 74.2mm×74.2mm×1.6mm glass-epoxy board, occupied area by copper foil : 10.29mm2 , in each layers
4-layer. mounted on a 74.2mm×74.2mm×1.6mm glass-epoxy board, occupied area by copper foil : 5505mm2, in each layers
●Operating Ratings(Ta=-40 to +105℃)
Parameter
Power Supply Voltage
EN Voltage
Output voltage Setting Range
SW average output current
*6
*7
Symbol
VCC
PVCC
VEN
VOUT
ISW
Min.
2.7
2.7
0
0.8
-
Ratings
Typ.
3.3
3.3
-
Max.
5.5
5.5
5.5
6
2.5*
7
3.0*
Units
V
V
V
V
A
In case set output voltage 1.6V or more, VccMin = Vout+1.2V.
Pd should not be exceeded.
●Electrical Characteristics(Ta=25℃ VCC=PVCC=3.3V, EN=VCC, R1=10kΩ, R2=5kΩ ,unless otherwise specified.)
Limit
Parameter
Symbol
Units
Conditions
Min.
Typ.
Max.
Standby current
ISTB
0
10
μA
EN=GND
Active current
ICC
250
500
μA
EN Low voltage
Standby mode
VENL
GND
0.8
V
EN High voltage
Active mode
VENH
2.0
Vcc
V
EN input current
IEN
1
10
μA
VEN=3.3V
Oscillation frequency
FOSC
0.8
1
1.2
MHz
High side FET ON resistance
RONH
82
115
mΩ
PVCC=3.3V
Low side FET ON resistance
RONL
70
98
mΩ
PVCC=3.3V
ADJ Voltage
VADJ
0.788
0.800
0.812
V
ITH SInk current
ITHSI
10
18
μA
VADJ=1V
ITH Source Current
ITHSO
10
18
μA
VADJ=0.6V
UVLO threshold voltage
VUVLO1
2.400
2.500
2.600
V
VCC=3.3V→0V
UVLO release voltage
VUVLO2
2.425
2.550
2.700
V
VCC=0V→3.3V
Soft start time
TSS
2.5
5
10
ms
Timer latch time
TLATCH
0.5
1
2
ms
Output Short circuit
VSCP
0.40
0.56
V
VADJ =0.8V→0V
Threshold Voltage
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
3/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
●Typical Performance Curves
Fig.4 Vcc - VOUT
Fig.5 VEN - VOUT
Fig.6 IOUT - VOUT
Fig.7 Ta - VOUT
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
4/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
Fig.8 Efficiency
Fig.9 Ta - Fosc
Fig.10 Ta – RONN, RONP
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
Fig.11 Ta - VEN
5/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
Fig.12 Ta - Icc
Fig.13 Vcc - Fosc
Fig.14 Soft start waveform
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
Fig.15 SW waveform Io=10mA
6/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
Fig. 16 Transient Response
Io=1→3A(10μs)
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
Fig.17 Transient Response
Io=3→1A(10μs)
7/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
●Application Information
Operation
BD8962MUV is a synchronous rectifying step-down switching regulator that achieves faster transient response by employing
current mode PWM control system.
○Synchronous rectifier
It does not require the power to be dissipated by a rectifier externally connected to a conventional DC/DC converter IC, and
its P.N junction shoot-through protection circuit limits the shoot-through current during operation, by which the power
dissipation of the set is reduced.
○Current mode PWM control
Synthesizes a PWM control signal with a inductor current feedback loop added to the voltage feedback.
・PWM (Pulse Width Modulation) control
The oscillation frequency for PWM is 1 MHz. SET signal form OSC turns ON a highside MOS FET (while a lowside MOS
FET is turned OFF), and an inductor current IL increases. The current comparator (Current Comp) receives two signals, a
current feedback control signal (SENSE: Voltage converted from I L) and a voltage feedback control signal (FB), and issues
a RESET signal if both input signals are identical to each other, and turns OFF the highside MOS FET (while a lowside
MOS FET is turned ON) for the rest of the fixed period. The PWM control repeat this operation.
SENSE
Current
Comp
RESET
VOUT
Level
Shift
R Q
FB
SET
Gm Amp.
ITH
S
IL
Driver
Logic
VOUT
SW
Load
OSC
Fig.18 Diagram of current mode PWM control
PVCC
Current
Comp
SENSE
FB
SET
GND
RESET
GND
SW
GND
IL
IL(AVE)
VOUT
VOUT(AVE)
Fig.19 PWM switching timing chart
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
8/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
Description of Operations
・Soft-start function
EN terminal shifted to “High” activates a soft-starter to gradually establish the output voltage with the current limited during
startup, by which it is possible to prevent an overshoot of output voltage and an inrush current.
・Shutdown function
With EN terminal shifted to “Low”, the device turns to Standby Mode, and all the function blocks including reference voltage
circuit, internal oscillator and drivers are turned to OFF. Circuit current during standby is 0μF (Typ.).
・UVLO function
Detects whether the input voltage sufficient to secure the output voltage of this IC is supplied.
And the hysteresis width of
50mV (Typ.) is provided to prevent output chattering.
Hysteresis 50mV
VCC
EN
VOUT
Tss
Tss
Tss
Soft start
Standby mode
Operating mode
Standby
mode
Standby
mode
Operating mode
UVLO
UVLO
Operating mode
EN
Standby mode
UVLO
Fig.20 Soft start, Shutdown, UVLO timing chart
・Short-current protection circuit with time delay function
Turns OFF the output to protect the IC from breakdown when the incorporated current limiter is activated continuously for
the fixed time(TLATCH) or more. The output thus held tuned OFF may be recovered by restarting EN or by re-unlocking
UVLO.
EN
1msec
VOUT
Output Current in non-control
1/2VOUT
Until output voltage goes up the half of Vo or over,
timer latch is not operated.
(No timer latch, only limit to the output current)
Limit
Output voltage OFF Latch
IL
Output Current in control by limit value
(With fall of the output voltage, limit value goes down)
Standby mode
Standby mode
Operated mode
EN
Timer Latch
Operated mode
EN
Fig.21 Short-current protection circuit with time delay timing chart
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
9/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
Information on Advantages
Advantage 1:Offers fast transient response with current mode control system.
Conventional product (Load response IO=1A→3A)
VOUT
BD8962MUV (Load response IO=1A→3A)
VOUT
62mV
145mV
IOUT
IOUT
Voltage drop due to sudden change in load was reduced by about 50%.
Fig.22 Comparison of transient response
Advantage 2: Offers high efficiency for all load range with synchronous rectifier.
100
【VOUT=1.2】
Utilizes the synchronous rectifying mode and the low on-resistance
MOS FETs incorporated as power transistor.
90
EFFICIENCY: η [%]
80
ON resistance of Highside MOS FET : 82mΩ(Typ.)
ON resistance of Lowside MOS FET : 70mΩ(Typ.)
70
60
50
40
30
VCC=5V
Ta=25℃
20
10
0
10
100
1000
OUTPUT CURRENT:IOUT[mA]
10000
Fig.23 Efficiency
Advantage 3:・Supplied in smaller package due to small-sized power MOS FET incorporated.
・Output capacitor Co required for current mode control: 22μF ceramic capacitor
・Inductance L required for the operating frequency of 1 MHz: 2.2μH inductor
・Incorporates FET + Boot strap diode
Reduces a mounting area required.
VCC
EN
VCC
VREF
20mm
BST
Current
Comp
RQ
S
+
SLOPE
Gm Amp
+
Soft
Start
CLK
PVCC
Current
Sense/
Protect
OSC
VCC
UVLO
3.3V
Input
Cf
SW
Output
Rf
PVCC
+
Driver
Logic
TSD
SCP
CBST
R2
15mm
PGND
R1
L
CIN
RITH
GND
CITH
ADJ
Co
ITH
RITH CITH
R1 R2
Fig.24 Example application
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
10/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
Switching Regulator Efficiency
Efficiency ŋ may be expressed by the equation shown below:
η=
VOUT×IOUT
×100[%]=
POUT
Vin×Iin
×100[%]=
Pin
POUT
POUT+PDα
×100[%]
Efficiency may be improved by reducing the switching regulator power dissipation factors P Dα as follows:
Dissipation factors:
2
1) ON resistance dissipation of inductor and FET:PD(I R)
2) Gate charge/discharge dissipation:PD(Gate)
3) Switching dissipation:PD(SW)
4) ESR dissipation of capacitor:PD(ESR)
5) Operating current dissipation of IC:PD(IC)
2
2
1)PD(I R)=IOUT ×(RCOIL+RON) (RCOIL[Ω]:DC resistance of inductor, RON[Ω]:ON resistance of FET, IOUT[A]:Output
current.)
2)PD(Gate)=Cgs×f×V (Cgs[F]:Gate capacitance of FET, f[H]:Switching frequency, V[V]:Gate driving voltage of FET)
2
Vin ×CRSS×IOUT×f
IDRIVE
3)PD(SW)=
(CRSS[F]:Reverse transfer capacitance of FET, IDRIVE[A]:Peak current of gate.)
2
4)PD(ESR)=IRMS ×ESR (IRMS[A]:Ripple current of capacitor, ESR[Ω]:Equivalent series resistance.)
5)PD(IC)=Vin×ICC (ICC[A]:Circuit current.)
Consideration on Permissible Dissipation and Heat Generation
As this IC functions with high efficiency without significant heat generation in most applications, no special
consideration is needed on permissible dissipation or heat generation.
In case of extreme conditions,
however, including lower input voltage, higher output voltage, heavier load, and/or higher temperature, the
permissible dissipation and/or heat generation must be carefully considered.
For dissipation, only conduction losses due to DC resistance of inductor and ON resistance of FET are considered.
Because the conduction losses are considered to play the leading role among other dissipation mentioned above including
gate charge/discharge dissipation and switching dissipation.
4 layers (Copper foil area : 5505mm 2)
copper foil in each layers.
θj-a=35.1℃/W
2
② 4 layers (Copper foil area : 10.29m )
copper foil in each layers.
θj-a=103.3℃/W
2
③ 4 layers (Copper foil area : 10.29m )
θj-a=178.6℃/W
④IC only.
θj-a=367.6℃/W
①
Power dissipation:Pd [W]
4.0
①3.56W
3.0
2
P=IOUT ×RON
RON=D×RONP+(1-D)RONN
D:ON duty (=VOUT/VCC)
RONH:ON resistance of Highside MOS FET
RONL:ON resistance of Lowside MOS FET
IOUT:Output current
2.0
②1.21W
1.0
③0.70W
④0.34W
0
0
25
50
75
100105 125
150
Ambient temperature:Ta [℃]
Fig.25 Thermal derating curve
(VQFN020V4040)
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
11/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
If VCC=3.3V, VOUT=1.8V, RONH=82mΩ, RONL=70mΩ
IOUT=3A, for example,
D=VOUT/VCC=1.8/3.3=0.545
RON=0.545×0.082+(1-0.545)×0.07
=0.0447+0.0319
=0.0766[Ω]
2
P=3 ×0.0766=0.6894[W]
As RONH is greater than RONL in this IC, the dissipation increases as the ON duty becomes greater.
consideration on the dissipation as above, thermal design must be carried out with sufficient margin allowed.
With the
Selection of Components Externally Connected
1. Selection of inductor (L)
The inductance significantly depends on output ripple current.
As seen in the equation (1), the ripple current decreases as the
inductor and/or switching frequency increases.
(VCC-VOUT)×VOUT
ΔIL=
[A]・・・(1)
L×VCC×f
IL
ΔIL
VCC
IL
Appropriate ripple current at output should be 20% more or less of the
maximum output current.
VOUT
L
ΔIL=0.2×IOUTmax. [A]・・・(2)
Co
(VCC-VOUT)×VOUT
L=
Fig.26 Output ripple current
ΔIL×VCC×f
[H]・・・(3)
(ΔIL: Output ripple current, and f: Switching frequency)
※Current exceeding the current rating of the inductor results in magnetic saturation of the inductor, which decreases
efficiency. The inductor must be selected allowing sufficient margin with which the peak current may not exceed its
current rating.
If VCC=5.0V, VOUT=2.5V, f=1MHz, ΔIL=0.2×3A=0.6A, for example,(BD8962MUV)
(5-2.5)×2.5
L=
0.6×5×1M
=2.08μ → 2.2[μH]
※Select the inductor of low resistance component (such as DCR and ACR) to minimize dissipation in the inductor for
better efficiency.
2. Selection of output capacitor (CO)
VCC
Output capacitor should be selected with the consideration on the stability region and the
equivalent series resistance required to smooth ripple voltage.
Output ripple voltage is determined by the equation (4):
VOUT
L
ESR
ΔVOUT=ΔIL×ESR [V]・・・(4)
Co
(ΔIL: Output ripple current, ESR: Equivalent series resistance of output capacitor)
Fig.27 Output capacitor
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
※Rating of the capacitor should be determined allowing sufficient margin against output voltage.
A 22μF to 100μF ceramic capacitor is recommended.
Less ESR allows reduction in output ripple voltage.
12/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
3. Selection of input capacitor (Cin)
VCC
Input capacitor to select must be a low ESR capacitor of the capacitance
sufficient to cope with high ripple current to prevent high transient voltage. The
ripple current IRMS is given by the equation (5):
Cin
VOUT
IRMS=IOUT×
L
√VOUT(VCC-VOUT)
[A]・・・(5)
VCC
Co
< Worst case > IRMS(max.)
IOUT
When Vcc=2×VOUT, IRMS=
2
If VCC=3.3V, VOUT=1.8V, and IOUTmax.=3A, (BD8962MUV)
Fig.28 Input capacitor
√1.8(3.3-1.8)
=1.49[ARMS]
3
3.3
.
3
A low ESR 22μF/10V ceramic capacitor is recommended to reduce ESR dissipation of input capacitor for better efficiency.
IRMS=2×
4. Determination of RITH, CITH that works as a phase compensator
As the Current Mode Control is designed to limit a inductor current, a pole (phase lag) appears in the low frequency area
due to a CR filter consisting of a output capacitor and a load resistance, while a zero (phase lead) appears in the high
frequency area due to the output capacitor and its ESR. So, the phases are easily compensated by adding a zero to the
power amplifier output with C and R as described below to cancel a pole at the power amplifier.
fp(Min.)
A
Gain
[dB]
0
fz(ESR)
IOUTMin.
Phase
[deg]
1
2π×RO×CO
1
fz(ESR)=
2π×ESR×CO
fp=
fp(Max.)
IOUTMax.
Pole at power amplifier
When the output current decreases, the load resistance Ro
increases and the pole frequency lowers.
0
-90
fp(Min.)=
1
[Hz]←with lighter load
2π×ROMax.×CO
fp(Max.)=
1
2π×ROMin.×CO
Fig.29 Open loop gain characteristics
[Hz] ←with heavier load
A
fz(Amp.)
Zero at power amplifier
Gain
[dB]
Increasing capacitance of the output capacitor lowers the pole
0
frequency while the zero frequency does not change.
(This is
because when the capacitance is doubled, the capacitor ESR
0
reduces to half.)
Phase
[deg]
-90
fz(Amp.)=
1
2π×RITH×CITH
Fig.30 Error amp phase compensation characteristics
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
13/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
Fig.31 Typical application
Stable feedback loop may be achieved by canceling the pole fp (Min.) produced by the output capacitor and the load
resistance with CR zero correction by the error amplifier.
fz(Amp.)= fp(Min.)
1
2π×RITH×CITH
=
1
2π×ROMax.×CO
5. Determination of output voltage
The output voltage VOUT is determined by the equation (6):
VOUT=(R2/R1+1)×VADJ・・・(6) VADJ: Voltage at ADJ terminal (0.8V Typ.)
With R1 and R2 adjusted, the output voltage may be determined as required.
L
6
Output
SW
Co
R2
1
ADJ
R1
Adjustable output voltage range : 0.8V to 2.5V
Fig.32 Determination of output voltage
Use 1 kΩ to 100 kΩ resistor for R1.
carefully for ripple voltage etc.
If a resistor of the resistance higher than 100 kΩ is used, check the assembled set
3.7
The lower limit of input voltage depends on the output voltage.
Basically, it is recommended to use in the condition :
VCCmin = VOUT+1.2V.
Fig.33. shows the necessary output current value at the lower
limit of input voltage. (DCR of inductor : 20mΩ)
This data is the characteristic value, so it’ doesn’t guarantee the
operation range.
INPUT VOLTAGE : VCC[V]
3.5
Vo=2.5V
3.3
Vo=2.0V
3.1
Vo=1.8V
2.9
2.7
0
1
2
3
OUTPUT CURRENT : IOUT[A]
Fig.33 minimum input voltage in each output voltage
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
14/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
BD8962MUV Cautions on PC Board layout
Fig.34 Layout diagram
① Lay out the input ceramic capacitor CIN closer to the pins PVCC and PGND, and the output capacitor Co closer to the
pin PGND.
② Lay out CITH and RITH between the pins ITH and GND as neat as possible with least necessary wiring.
※
VQFN020V4040 (BD8962MUV) has thermal PAD on the reverse of the package.
The package thermal performance may be enhanced by bonding the PAD to GND plane which take a large area
of PCB.
Recommended Components Lists on Above Application
Symbol
Part
Value
2.0uH
L
Coil
2.2uH
Manufacturer
Sumida
Series
CDR6D28MNP-2R0NC
Sumida
CDR6D26NP-2R2NC
CIN
Ceramic capacitor
22uF
Murata
GRM32EB11A226KE20
CO
Ceramic capacitor
22uF
Murata
GRM31CB30J226KE18
CITH
RITH
Ceramic capacitor
Resistance
Cf
Ceramic capacitor
Rf
Resistance
CBST
Ceramic capacitor
VOUT=1.0V
1500pF
Murata
CRM18 Serise
VOUT=1.2V
1000pF
Murata
VOUT=1.5V
VOUT=1.8V
1000pF
560pF
Murata
Murata
GRM18 Serise
GRM18 Serise
GRM18 Serise
VOUT=2.5V
VOUT=1.0V
560pF
5.6kΩ
Murata
Rohm
GRM18 Serise
MCR03 Serise
VOUT=1.2V
VOUT=1.5V
6.8kΩ
6.8kΩ
Rohm
Rohm
MCR03 Serise
MCR03 Serise
VOUT=1.8V
VOUT=2.5V
8.2kΩ
12kΩ
Rohm
Rohm
MCR03 Serise
MCR03 Serise
1000 pF
Murata
GRM18 Serise
10Ω
Rohm
MCR03 Serise
0.1 uF
Murata
GRM18 Serise
※The parts list presented above is an example of recommended parts. Although the parts are sound, actual circuit
characteristics should be checked on your application carefully before use. Be sure to allow sufficient margins to
accommodate variations between external devices and this IC when employing the depicted circuit with other circuit
constants modified. Both static and transient characteristics should be considered in establishing these margins. When
switching noise is substantial and may impact the system, a low pass filter should be inserted between the VCC and PVCC
pins, and a schottky barrier diode or snubber established between the SW and PGND pins.
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
15/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
I/O Equivalence Circuit【BD8962MUV】
・EN pin
PVCC
・SW pin
PVCC
PVCC
EN
SW
・ADJ pin
・ITH pin
VCC
ADJ
ITH
・BST pin
PVCC
PVCC
BST
SW
Fig.35 I/O equivalence circuit
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
16/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
●Operational Notes
1. Absolute Maximum Ratings
While utmost care is taken to quality control of this product, any application that may exceed some of the absolute
maximum ratings including the voltage applied and the operating temperature range may result in breakage. If broken,
short-mode or open-mode may not be identified. So if it is expected to encounter with special mode that may exceed the
absolute maximum ratings, it is requested to take necessary safety measures physically including insertion of fuses.
2. Electrical potential at GND
GND must be designed to have the lowest electrical potential In any operating conditions.
3. Short-circuiting between terminals, and mismounting
When mounting to pc board, care must be taken to avoid mistake in its orientation and alignment. Failure to do so may
result in IC breakdown. Short-circuiting due to foreign matters entered between output terminals, or between output and
power supply or GND may also cause breakdown.
4. Thermal shutdown protection circuit
Thermal shutdown protection circuit is the circuit designed to isolate the IC from thermal runaway, and not intended to
protect and guarantee the IC. So, the IC the thermal shutdown protection circuit of which is once activated should not
be used thereafter for any operation originally intended.
5. Inspection with the IC set to a pc board
If a capacitor must be connected to the pin of lower impedance during inspection with the IC set to a pc board, the
capacitor must be discharged after each process to avoid stress to the IC. For electrostatic protection, provide proper
grounding to assembling processes with special care taken in handling and storage. When connecting to jigs in the
inspection process, be sure to turn OFF the power supply before it is connected and removed.
6. Input to IC terminals
+
This is a monolithic IC with P isolation between P-substrate and each element as illustrated below. This P-layer and
the N-layer of each element form a P-N junction, and various parasitic element are formed.
If a resistor is joined to a transistor terminal as shown in Fig 36.
○P-N junction works as a parasitic diode if the following relationship is satisfied; GND>Terminal A (at resistor side), or
GND>Terminal B (at transistor side); and
○if GND>Terminal B (at NPN transistor side),
a parasitic NPN transistor is activated by N-layer of other element adjacent to the above-mentioned parasitic diode.
The structure of the IC inevitably forms parasitic elements, the activation of which may cause interference among circuits,
and/or malfunctions contributing to breakdown. It is therefore requested to take care not to use the device in such
manner that the voltage lower than GND (at P-substrate) may be applied to the input terminal, which may result in
activation of parasitic elements.
Resistor
Transistor (NPN)
Pin A
Pin B
C
B
Pin B
E
Pin A
N
N
P+
N
P+
P
N
P substrate
Parasitic element
GND
P+
Parasitic
element
B
N
P+
P
N
C
E
P substrate
Parasitic element
GND
GND
GND
Parasitic
element
Other adjacent elements
Fig.36 Simplified structure of monorisic IC
7. Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND pattern from
the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that resistance to the wiring
pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the small-signal GND. Pay attention
not to cause fluctuations in the GND wiring pattern of external parts as well.
8 . Selection of inductor
It is recommended to use an inductor with a series resistance element (DCR) 0.1Ω or less. Especially, in case output
voltage is set 1.6V or more, note that use of a high DCR inductor will cause an inductor loss, resulting in decreased output
voltage. Should this condition continue for a specified period (soft start time + timer latch time), output short circuit
protection will be activated and output will be latched OFF. When using an inductor over 0.1Ω, be careful to ensure
adequate margins for variation between external devices and this IC, including transient as well as static characteristics.
Furthermore, in any case, it is recommended to start up the output with EN after supply voltage is within operation range.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
17/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
BD8962MUV
●Ordering Information
B
D
8
9
6
2
M
U
V
E2
Package
MUV: VQFN020V4040
Part Number
Packaging and forming specification
E2: Embossed tape and reel
●Physical Dimension Tape and Reel Information
VQFN020V4040
<Dimension>
<Tape and Reel information>
Tape
Embossed carrier tape
Quantity
2500pcs
Direction
of feed
E2
(The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand)
1234
1234
1Pin
1234
1234
1234
1234
Reel
(Unit:mm)
Direction of feed
※When you order , please order in times the amount of package quantity.
●Marking Diagram
VQFN020V4040 (TOP VIEW)
Part Number Marking
D 8 9 6 2
LOT Number
1PIN MARK
www.rohm.com
© ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
18/18
TSZ2201-0J3J0AJ00030-1-2
02.MAR.2012 Rev.001
Datasheet
Notice
●Precaution for circuit design
1) The products are designed and produced for application in ordinary electronic equipment (AV equipment, OA
equipment, telecommunication equipment, home appliances, amusement equipment, etc.). If the products are to be
used in devices requiring extremely high reliability (medical equipment, transport equipment, aircraft/spacecraft,
nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose
malfunction or operational error may endanger human life and sufficient fail-safe measures, please consult with the
ROHM sales staff in advance. If product malfunctions may result in serious damage, including that to human life,
sufficient fail-safe measures must be taken, including the following:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits in the case of single-circuit failure
2)
The products are designed for use in a standard environment and not in any special environments. Application of the
products in a special environment can deteriorate product performance. Accordingly, verification and confirmation of
product performance, prior to use, is recommended if used under the following conditions:
[a] Use in various types of liquid, including water, oils, chemicals, and organic solvents
[b] Use outdoors where the products are exposed to direct sunlight, or in dusty places
[c] Use in places where the products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2,
and NO2
[d] Use in places where the products are exposed to static electricity or electromagnetic waves
[e] Use in proximity to heat-producing components, plastic cords, or other flammable items
[f] Use involving sealing or coating the products with resin or other coating materials
[g] Use involving unclean solder or use of water or water-soluble cleaning agents for cleaning after soldering
[h] Use of the products in places subject to dew condensation
3)
The products are not radiation resistant.
4)
Verification and confirmation of performance characteristics of products, after on-board mounting, is advised.
5)
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
6)
De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta).
When used in sealed area, confirm the actual ambient temperature.
7)
Confirm that operation temperature is within the specified range described in product specification.
8)
Failure induced under deviant condition from what defined in the product specification cannot be guaranteed.
●Precaution for Mounting / Circuit board design
1) When a highly active halogenous (chlorine, bromine, etc.) flux is used, the remainder of flux may negatively affect
product performance and reliability.
2)
In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
Company in advance.
Regarding Precaution for Mounting / Circuit board design, please specially refer to ROHM Mounting specification
●Precautions Regarding Application Examples and External Circuits
1) If change is made to the constant of an external circuit, allow a sufficient margin due to variations of the characteristics
of the products and external components, including transient characteristics, as well as static characteristics.
2)
The application examples, their constants, and other types of information contained herein are applicable only when
the products are used in accordance with standard methods. Therefore, if mass production is intended, sufficient
consideration to external conditions must be made.
Notice - Rev.001
Datasheet
●Precaution for Electrostatic
This product is Electrostatic sensitive product, which may be damaged due to Electrostatic discharge. Please take proper
caution during manufacturing and storing so that voltage exceeding Product maximum rating won't be applied to products.
Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from
charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
●Precaution for Storage / Transportation
1) Product performance and soldered connections may deteriorate if the products are stored in the following places:
[a] Where the products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] Where the temperature or humidity exceeds those recommended by the Company
[c] Storage in direct sunshine or condensation
[d] Storage in high Electrostatic
2)
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using products of which storage time is
exceeding recommended storage time period .
3)
Store / transport cartons in the correct direction, which is indicated on a carton as a symbol. Otherwise bent leads may
occur due to excessive stress applied when dropping of a carton.
4)
Use products within the specified time after opening a dry bag.
●Precaution for product label
QR code printed on ROHM product label is only for internal use, and please do not use at customer site. It might contain a
internal part number that is inconsistent with an product part number.
●Precaution for disposition
When disposing products please dispose them properly with a industry waste company.
●Precaution for Foreign exchange and Foreign trade act
Since concerned goods might be fallen under controlled goods prescribed by Foreign exchange and Foreign trade act,
please consult with ROHM in case of export.
●Prohibitions Regarding Industrial Property
1) Information and data on products, including application examples, contained in these specifications are simply for
reference; the Company does not guarantee any industrial property rights, intellectual property rights, or any other
rights of a third party regarding this information or data. Accordingly, the Company does not bear any responsibility for:
[a] infringement of the intellectual property rights of a third party
[b] any problems incurred by the use of the products listed herein.
2)
The Company prohibits the purchaser of its products to exercise or use the intellectual property rights, industrial
property rights, or any other rights that either belong to or are controlled by the Company, other than the right to use,
sell, or dispose of the products.
Notice - Rev.001
Similar pages