LTC6417 1.6GHz Low Noise High Linearity Differential Buffer/16-Bit ADC Driver with Fast Clamp Description Features 1.6GHz –3dB Small Signal Bandwidth Low Distortion Driving 50Ω Load, 2.4VP-P Out –100dBc/–69dBc HD2/HD3 at 140MHz –80dBc IM3 and 46dBm OIP3 at 140MHz –100dBc/–66dBc HD2/HD3 at 380MHz –68dBc IM3 and 39dBm OIP3 at 380MHz 1.5nV/√Hz Output Noise 4.3pA/√Hz Input Current Noise Programmable High Speed, Fast Recovery Output Clamping 4.28VP-P Maximum Output Swing on a 50Ω Differential Load DC-Coupled Signal Path Operates on Single 4.75V to 5.25V Supply Power: 615mW on 5V, Can Be Reduced to 370mW, Shutdown Mode 120mW 3mm × 4mm 20-Lead QFN Package n n n n n n n n n Applications n n n With no external biasing or gain setting components and a flow-through pinout, the LTC6417 is very easy to use. It can be DC-coupled and has a common mode output offset of –60mV. The LTC6417 input pins are internally biased to provide an output common mode voltage that is set by the voltage on the VCM pin for AC-coupled applications. Supply current is typically 123mA and the LTC6417 operates on supply voltages ranging from 4.75V to 5.25V. Power consumption can be reduced to 74mA via the PWRADJ pin. The LTC6417 also has a hardware shutdown feature which reduces current consumption to 24mA. The LTC6417 features fast, adjustable output voltage clamping to help protect subsequent circuitry. The CLHI pin sets the maximum swing, while a symmetric minimum swing is set up internally. LTC6417 VOR pin will signal overrange when the clamps limit output voltage. Differential ADC Driver CCD Buffer Cable Driver 50Ω Buffer n The LTC®6417 is a differential unity gain buffer that can drive a 50Ω load with extremely low noise and excellent linearity. It is well suited for driving high speed 14- and 16-bit pipeline ADCs with input signals from DC to beyond 600MHz. Differential input impedance is 18.5kΩ, allowing 1:4 and 1:8 transformers to be used at the input providing additional system gain in 50Ω systems. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. The LTC6417 is packaged in a 20-lead 3mm × 4mm QFN package. Pinout is optimized for placement directly adjacent to Linear Technology’s high speed 14- and 16-bit ADCs. Typical Application LTC6417 Driving LTC2209 16-Bit ADC 32K Point FFT, fIN = 140MHz, –1dBFS, PGA = 0 LTC6417 Driving an LTC2209 16-Bit ADC at 140MHz IF 3.3V 5V 680pF T1 WBC4-14LB 4 3 2 50Ω + – 6 • • 0.01µF 1 0 2.2µF 0.1µF 1,6, 11,16 100Ω 100Ω 0.01µF 8 9 C43 27pF E1 51nH E3 75nH C45 18pF HD2 = –88dBc HD3 = –94dBc SFDR = 88dBc SNR = 75.4dB SEE FIGURE 1/TABLE 1 1:4 BALUN fS = 153.6Msps DEMO BOARD DC1685A –10 –20 –30 5 V+ PWRADJ IN+ R36 60.4Ω 2 CLHI LTC6417 19 C41 12pF OUT+ OUT – V IN– 18 VCM OR 14 SHDN 15 GND 12 1k 3, 7,10, 17, 20, 21 2.2µF R12 60.4Ω C44 27pF E2 51nH R42 300Ω E5 51nH C40 12pF C10 12pF 10Ω AIN+ R53 120Ω R43 300Ω E3 75nH – 10Ω LTC2209 16 AIN VCM PGA = 0 C46 18pF AMPLITUDE (dBFS) n –40 –50 –60 –70 –80 –90 –100 –110 CLOCK (153.6MHz) 6417 TA01a –120 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 6417 TA01b 6417f 1 LTC6417 Absolute Maximum Ratings Pin Configuration (Note 1) GND OUT– GND OUT+ TOP VIEW Total Supply Voltage (V+ to GND)..............................5.5V Input Current (CLHI, VCM)..................................... ±10mA Input Current (IN+, IN–).........................................±30mA Output Current (OUT+, OUT–).............................. ±100mA Output Current (VOR)............................................ ±10mA Operating Temperature Range (TC) (Note 2)........................................... –40°C to 105°C Specified Temperature Range (TC) (Note 3)........................................... –40°C to 105°C Storage Temperature Range................... –65°C to 150°C Junction Temperature (TJMAX)............................... 150°C 20 19 18 17 V+ 1 16 V+ CLHI 2 15 VCM GND 3 NC 4 PWRADJ 5 12 SHDN + 6 11 V+ IN+ 13 NC 9 10 GND 8 IN– 7 GND V 14 VOR 21 GND UDC PACKAGE 20-LEAD (3mm × 4mm) PLASTIC QFN TJMAX = 150°C, θJA = 52°C/W, θJC = 6.8°C/W EXPOSED PAD (PIN 21) IS GND, MUST BE SOLDERED TO PCB Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC6417CUDC#PBF LTC6417CUDC#TRPBF LFVN 20-Lead (3mm × 4mm) Plastic QFN 0°C to 70°C LTC6417IUDC#PBF LTC6417IUDC#TRPBF LFVN 20-Lead (3mm × 4mm) Plastic QFN –40°C to 105°C (TC) *Temperature grades are identified by a label on the shipping container. Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ DC Electrical Characteristics + The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V = 5V, GND = 0V, No RLOAD, CLOAD = 6pF. VCM = 1.25V, CLHI = V+, PWRADJ = V+, SHDN = 0V unless otherwise noted. VINCM is defined as (IN+ + IN–)/2. VOUTCM is defined as (OUT+ + OUT–)/2. VINDIFF is defined as (IN+ – IN–). VOUTDIFF is defined as (OUT+ – OUT–). See DC test circuit schematic. SYMBOL PARAMETER CONDITIONS MIN TYP MAX –0.15 –0.2 –0.1 0 0 UNITS Input/Output Characteristics GDIFF Differential Gain VINDIFF = ±1.2V Differential l TCGDIFF Differential Gain Temperature Coefficient VSWINGDIFF Differential Output Voltage Swing l VOUTDIFF, VINDIFF = ±2.3V l VSWINGMIN Output Voltage Swing Low Single-Ended Measurement of OUT+, OUT– l VINDIFF = ±2.3V VSWINGMAX Output Voltage Swing High Single-Ended Measurement of OUT+, OUT– l VINDIFF = ±2.3V 4 3.3 0.0002 dB/°C 4.28 VP-P VP-P 0.19 2.25 2.05 dB dB 2.33 0.28 0.4 V V V V 6417f 2 LTC6417 DC Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V+ = 5V, GND = 0V, No RLOAD, CLOAD = 6pF. VCM = 1.25V, CLHI = V+, PWRADJ = V+, SHDN = 0V unless otherwise noted. VINCM is defined as (IN+ + IN–)/2. VOUTCM is defined as (OUT+ + OUT–)/2. VINDIFF is defined as (IN+ – IN–). VOUTDIFF is defined as (OUT+ – OUT–). See DC test circuit schematic. SYMBOL PARAMETER CONDITIONS IOUT Output Current Drive (Notes 1, 4) Single-Ended Measurement of OUT+, OUT– VOS Differential Input Offset Voltage IN+ = IN– = 1.25V, VOS = VOUTDIFF/GDIFF TCVOS Differential Input Offset Voltage Drift VIOCM Common Mode Offset Voltage, Input to Output VOUTCM – VINCM IVRMIN Input Voltage Range, IN+, IN– (Minimum) (Single-Ended) Defined by Output Voltage Swing Test l IVRMAX Input Voltage Range IN+, IN– (Maximum) (Single-Ended) Defined by Output Voltage Swing Test l 2.4 IB Input Bias Current, IN+, IN– IN+ = IN– = 1.25V –13 –18 2 l 13 18 µA µA 12 11 18.5 l 25 27.5 kΩ kΩ 9.25 l 5.8 5 13 15 kΩ kΩ 63 60 91 l RINDIFF Differential Input Resistance MIN –0.1 l –3.2 –4 –120 –140 –60 VINDIFF = ±1.2V Differential Input Capacitance Input Common Mode Resistance IN+ = IN– = 0.65V to 1.85V CMRR Common Mode Rejection Ratio IN+ = IN– = 0.65V to 1.85V, CMRR = (VOUTDIFF/GDIFF/1.2V) 3.2 4 ±100 l RINCM MAX l UNITS mA 1 l CINDIFF TYP mV mV µV/°C –10 0 mV mV 0.1 V V 1 pF dB dB ROUTDIFF Differential Output Resistance eN Input Noise Voltage Density f = 100kHz 1.5 3 nV/√Hz Ω iN Input Noise Current Density f = 100kHz 4.3 pA/√Hz V/V V/V Output Common Mode Voltage Control GCM VINCMDEFAULT VOS (VCM – VINCM) VOUTCMDEFAULT VOS (VCM – VOUTCM) VOUTCMMIN VOUTCMMAX VCMDEFAULT RVCM VCM Pin Common Mode Gain Default Input Common Mode Voltage Offset Voltage, VCM to VINCM VCM = 0.65V to 1.85V 0.82 0.8 0.92 l 1.15 1.1 1.25 l 1.35 1.4 V V –85 –90 15 l 115 135 mV mV 1.1 1 1.2 l 1.3 1.35 V V –50 –45 75 l 200 230 mV mV 0.29 0.63 0.65 V V VINCM. IN+, IN–, VCM Pin Floating VCM – VINCM, VCM = 1.25V Default Output Common Mode Voltage Inputs Floating, VCM Pin Floating Offset Voltage, VCM to VOUTCM VCM – VOUTCM, VCM = 1.25V Output Common Mode Voltage Range (Minimum) VCM = 0.1V Output Common Mode Voltage Range (Maximum) VCM = 2.4V l 2 1.85 2.25 l 1.15 1.1 1.25 l 1.35 1.4 V V 2 1.9 2.7 l 3.4 3.7 kΩ kΩ VCM Pin Default Voltage VCM Pin Input Resistance CVCM VCM Pin Input Capacitance IBVCM VCM Pin Bias Current VCM = 0.65V to 1.85V V V 1 VCM = 1.25V l –15 –27.5 1 pF 15 27.5 µA µA 6417f 3 LTC6417 DC Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V+ = 5V, GND = 0V, No RLOAD, CLOAD = 6pF. VCM = 1.25V, CLHI = V+, PWRADJ = V+, SHDN = 0V unless otherwise noted. VINCM is defined as (IN+ + IN–)/2. VOUTCM is defined as (OUT+ + OUT–)/2. VINDIFF is defined as (IN+ – IN–). VOUTDIFF is defined as (OUT+ – OUT–). See DC test circuit schematic. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 2.4 2.35 2.48 l 2.55 2.6 V V –60 –85 20 l 80 85 mV mV VCLHI = 2.0V, VCM = 1.25V, IN+ = 2.4V, IN– = 0.1V –100 –110 10 l 100 110 mV mV Low Side Clamp Gain with Respect to CLHI Pin VCLHI = 2.0V, VCM = 1.25V, IN+ = 2.4V, IN– = 0.1V –1.2 –1.25 –1 l –0.8 –0.75 V/V V/V Low Side Clamp Gain with Respect to CM Pin VCLHI = 2.0V, VCM = 1.25V, IN+ = 2.4V, IN– = 0.1V 1.65 1.5 1.9 l 2.2 2.25 V/V V/V CLHI Pin Input Resistance VCLHI = 1.5V to 2.5V 3.4 3.1 4.8 l 5.7 6 kΩ kΩ –12 –12.5 3 l 18 18.5 µA µA l 4.75 5.25 V 100 95 123 l 140 145 mA mA 65 63 72 l 17 15 24 l DC Clamping Characteristics VCLHIDEFAULT Default Output Clamp Voltage, High VOS (CLHI – VOUTCM) Offset Voltage, CLHI to VOUTCM VOS (CLLO – VOUT) GLOHI GLOCM RCLHI IBCLHI Offset Voltage, CLLO to VOUT CLHI Pin Bias Current VCLHI = 2.5V Power Supply VS Supply Voltage Range IS Supply Current PSRR Power Supply Rejection Ratio VS = 4.75V to 5.25V dB dB SHDN Pin ISSHDN Shutdown Current VSHDN = 5V 29 35 mA mA VSHDNDEFAULT Default Shutdown Voltage l 0.1 V VIL,SHDN SHDN Input Low Voltage l 2 V VIH,SHDN SHDN Input High Voltage l 3.5 IIL,SHDN SHDN Input Low Current –1.6 –2 0 l 1.6 2 µA µA 275 250 380 l 450 475 µA µA 10.5 l 6 5 14 15 kΩ kΩ 1.5 1.45 1.65 1.8 1.85 V V 45 40 74 l 105 110 mA mA –145 –165 –120 l –80 –75 µA µA 210 200 240 l 290 300 µA µA IIH,SHDN SHDN Input High Current CSHDN SHDN Pin Input Capacitance RSHDN SHDN Pin Input Resistance SHDN = 0V SHDN = 5V V 1 SHDN = 2.5V to 5V pF PWRADJ Pin VPWRADJDEFAULT Default PWRADJ Voltage PWRADJ Floating ISL Supply Low Current PWRADJ = 0V IIL,PWRADJ IIH,PWRADJ CPWRADJ PWRADJ Input Low Current PWRADJ Input High Current PWRADJ Pin Input Capacitance PWRADJ = 0V PWRADJ = 5V 1 pF 6417f 4 LTC6417 DC Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V+ = 5V, GND = 0V, No RLOAD, CLOAD = 6pF. VCM = 1.25V, CLHI = V+, PWRADJ = V+, SHDN = 0V unless otherwise noted. VINCM is defined as (IN+ + IN–)/2. VOUTCM is defined as (OUT+ + OUT–)/2. VINDIFF is defined as (IN+ – IN–). VOUTDIFF is defined as (OUT+ – OUT–). See DC test circuit schematic. SYMBOL PARAMETER CONDITIONS RPWRADJ PWRADJ Pin Input Resistance PWRADJ = 2.5V to 5.0V MIN TYP MAX UNITS 10.5 10 14.5 l 19 20 3.25 3.2 3.35 l 3.55 3.6 V V –900 –1150 –770 l –650 –500 µA µA 1 1.5 2 µA µA kΩ kΩ VOR Pin VOR(HI) IOR(DEFAULT) IOR(MAX) Maximum Voltage on VOR Pin Default Pull-Down Current on VOR Pin Maximum Pull-Down Current Both Clamps are Active VCL = 5.0V, VCM = 1.25V VCL = 50V, VCM = 1.25V VCL = 2.0V, VCM = 1.25V, IN+ = 2.4V, IN– = 0.1V l AC Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V+ = 5V unless otherwise noted, GND = 0V, RLOAD = 500Ω,CLOAD = 6pF. VCM = 1.25V, CLHI = V+, PWRADJ = VCC, SHDN = 0V unless otherwise noted. VINCM is defined as (IN+ + IN–)/2. VOUTCM is defined as (OUT+ + OUT–)/2. VINDIFF is defined as (IN+ – IN–). VOUTDIFF is defined as (OUT+ – OUT–). See DC test circuit schematic. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Differential AC Characteristics –3dBBW –3dB Bandwidth 200mVP-P,OUT Differential 1.6 GHz 0.1dBBW ±0.1dB Bandwidth 200mVP-P,OUT Differential 0.18 GHz 0.5dBBW ±0.5dB Bandwidth 200mVP-P,OUT Differential 0.45 GHz 1/f 1/f Noise Corner 25 kHz SR Slew Rate Differential 10 V/ns tS1% 1% Settling Time 2VP-P,OUT 0.8 ns tOFF Shutdown Time SHDN = 0V to 5V 40 ns tON Enable Time SHDN = 5V to 0V 15 ns tPWRADJ,OFF PWRADJ Off Time PWRADJ = 5V to 0V 10 ns tPWRADJ,ON PWRADJ On Time PWRADJ = 0V to 5V 5 ns = 1.25V, IN+ = 1.625V to 1.25V, tCL,OFF 10% Clamp Release Time CLHI = 1.5V, VCM IN– = 1.25V to 0.875V 1 ns tCL,ON 10% Clamp Engage Time CLHI = 1.5V, VCM = 1.25V, IN+ = 1.25V to 1.625V, IN– = 1.25V to 0.875V 5 ns Common Mode AC Characteristics (VCM Pin) –3dBBW VCM Pin Small Signal –3dB BW VCM = 0.1VP-P, Measured Single-Ended at Output 10 MHz SRCM Common Mode Slew Rate Measured Single-Ended at Output 2 V/µs Overrange AC Characteristics (VOR Pin) –3dBBW VOR Pin Small Signal –3dB BW VOR = 0.1VP-P, CLHI = 2V, IN+ = 2.4V, IN– = 0.1V, RVOR = 1k, Measured Single-Ended at Output 200 MHz SRVOR Overrange Slew Rate Measured Single-Ended at Output 40 V/µs 1.9VP-P,OUT 2 ns AC Clamping Characteristics tOVDR Overdrive Recovery Time 6417f 5 LTC6417 AC Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V+ = 5V unless otherwise noted, GND = 0V, RLOAD = 500Ω,CLOAD = 6pF. VCM = 1.25V, CLHI = V+, PWRADJ = VCC, SHDN = 0V unless otherwise noted. VINCM is defined as (IN+ + IN–)/2. VOUTCM is defined as (OUT+ + OUT–)/2. VINDIFF is defined as (IN+ – IN–). VOUTDIFF is defined as (OUT+ – OUT–). See DC test circuit schematic. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –89 –93 dBc dBc IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –100 –110 dBc dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω 56 dBm P1dB Output 1dB Compression Point 16.1 dBm AC Linearity 10MHz Signal 70MHz Signal HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –74 –77 dBc dBc IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –86 –96 dBc dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω 48 dBm P1dB Output 1dB Compression Point 15.8 dBm 140MHz Signal HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –69 –73 dBc dBc IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –80 –91 dBc dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω P1dB Output 1dB Compression Point 46 dBm 15.8 dBm 200MHz Signal HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –68 –71 dBc dBc IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –78 –87 dBc dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω P1dB Output 1dB Compression Point 44 dBm 15.8 dBm 240MHz Signal HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –67 –70 dBc dBc IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –76 –85 dBc dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω P1dB Output 1dB Compression Point 43 dBm 15.7 dBm –66 –69 dBc dBc 300MHz Signal HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P 6417f 6 LTC6417 AC Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. V+ = 5V unless otherwise noted, GND = 0V, RLOAD = 500Ω,CLOAD = 6pF. VCM = 1.25V, CLHI = V+, PWRADJ = VCC, SHDN = 0V unless otherwise noted. VINCM is defined as (IN+ + IN–)/2. VOUTCM is defined as (OUT+ + OUT–)/2. VINDIFF is defined as (IN+ – IN–). VOUTDIFF is defined as (OUT+ – OUT–). See DC test circuit schematic. SYMBOL PARAMETER CONDITIONS MIN IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω P1dB Output 1dB Compression Point TYP –73 –79 MAX UNITS dBc dBc 41 dBm 15.6 dBm 380MHz Signal HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –66 –68 dBc dBc IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –68 –77 dBc dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω P1dB Output 1dB Compression Point 36 39 dBm 15.3 dBm VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –65 –68 dBc dBc 400MHz Signal HD3 Third Harmonic Distortion IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω –68 dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω 39 dBm P1dB Output 1dB Compression Point 15.3 dBm 500MHz Signal HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω VOUTDIFF = 2.4VP-P –65 –67 dBc dBc IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω –64 dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω P1dB Output 1dB Compression Point 37 dBm 15.0 dBm 600MHz Signal HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω –60 dBc IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω –58 dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω P1dB Output 1dB Compression Point 34 dBm 14.7 dBm 700MHz Signal HD3 Third Harmonic Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω –55 dBc IM3 Third Order Intermodulation Distortion VOUTDIFF = 2.4VP-P, RL = 50Ω –52 dBc OIP3 Output Third Order Intercept VOUTDIFF = 2.4VP-P, RL = 50Ω P1dB Output 1dB Compression Point Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC6417C/LTC6417I is guaranteed functional over the case temperature operating range of –40°C to 105°C. θJC = 6.8°C/W. 31 dBm 14.2 dBm Note 3: The LTC6417C is guaranteed to meet specified performance from 0°C to 70°C. It is designed, characterized and expected to meet specified performance from –40°C and 105°C case temperature range but is not tested or QA sampled at these temperatures. The LT6417I is guaranteed to meet specified performance from –40°C to 105°C case temperature range. Note 4: This parameter is pulse tested. 6417f 7 LTC6417 Typical Performance Characteristics –50 POUT = 11dBm –90 –40°C 25°C 6417 G01 –50 25°C –90 –40°C –100 0 0.5 1 1.5 105°C 25°C –95 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G04 POUT = 11dBm –50 V+ = 4.75V V+ = 5.0V V+ = 5.25V –70 –80 5 POUT = 11dBm –60 –70 –80 25°C 105°C –90 –100 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –40°C –100 HD3 at 140MHz vs VCM Over Temperature –40 –50 HD3 (dBc) 25°C 1 1.5 POUT = 11dBm –40 V+ = 4.75V V+ = 5.0V V+ = 5.25V –60 –70 4.5 5 –50 105°C –60 85°C –70 –80 –80 –80 –90 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –90 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –90 6417 G08 4 POUT = 11dBm 25°C –40°C 6417 G07 2 2.5 3 3.5 PWRADJ (V) HD3 at 140MHz vs PWRADJ Over Temperature HD3 (dBc) POUT = 11dBm 85°C 0.5 6417 G06 HD3 at 140MHz vs VCM Over V+ 105°C 0 6417 G05 –50 HD3 (dBc) 4.5 HD3 at 70MHz vs PWRADJ Over Temperature –90 –70 4 6417 G03 –40°C –60 2 2.5 3 3.5 PWRADJ (V) 85°C –85 –40 85°C 105°C –80 HD3 at 70MHz vs VCM Over V+ –60 85°C HD3 (dBc) HD3 (dBc) –75 –70 6417 G02 POUT = 11dBm –65 –80 –100 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) HD3 at 70MHz vs VCM Over Temperature –55 –70 POUT = 11dBm –60 –90 –100 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –45 –50 V+ = 4.75V V+ = 5.0V V+ = 5.25V HD3 (dBc) 85°C 105°C –80 POUT = 11dBm –60 HD3 (dBc) HD3 (dBc) –60 –70 HD3 at 30MHz vs PWRADJ Over Temperature HD3 at 30MHz vs VCM Over V+ HD3 (dBc) –50 HD3 at 30MHz vs VCM Over Temperature –40°C 0 0.5 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 5 6417 G09 6417f 8 LTC6417 Typical Performance Characteristics HD3 at 240MHz vs VCM Over Temperature –35 –40 POUT = 11dBm POUT = 11dBm –50 105°C –45 HD3 at 240MHz vs PWRADJ Over Temperature HD3 at 240MHz vs VCM Over V+ –40 V+ = 4.75V V+ = 5.0V V+ = 5.25V POUT = 11dBm –50 105°C 85°C –65 –70 –60 –40°C –75 –80 –80 –85 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –90 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –90 HD3 at 380MHz vs VCM Over Temperature –30 POUT = 11dBm –35 –65 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 25°C –30 V+ = 4.75V V+ = 5.0V V+ = 5.25V –50 –60 5 HD3 at 380MHz vs PWRADJ Over Temperature POUT = 11dBm –40 HD3 (dBc) 85°C HD3 (dBc) –55 POUT = 11dBm –40 105°C 0.5 6417 G12 HD3 at 380MHz vs VCM Over V+ –45 0 6417 G11 6417 G10 –25 25°C –70 25°C –40°C HD3 (dBc) –60 HD3 (dBc) HD3 (dBc) HD3 (dBc) 85°C –55 –50 105°C –60 –70 –70 –80 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –80 85°C 25°C –40°C –40°C –75 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G13 0.5 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 –30 POUT = 11dBm –40 5 HD3 at 500MHz vs PWRADJ Over Temperature HD3 at 500MHz vs VCM Over V+ POUT = 11dBm 4.5 6417 G15 6417 G14 HD3 at 500MHz vs VCM Over Temperature –30 0 –30 V+ = 4.75V V+ = 5.0V V+ = 5.25V POUT = 11dBm –40 –40 105°C –60 –70 25°C –50 HD3 (dBc) HD3 (dBc) HD3 (dBc) 85°C –50 –60 –50 105°C –60 –70 –70 –80 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –80 85°C 25°C –40°C –40°C –80 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G16 6417 G17 0 0.5 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 5 6417 G18 6417f 9 LTC6417 Typical Performance Characteristics –30 POUT = 11dBm POUT = 11dBm –40 105°C HD3 (dBc) HD3 (dBc) –40 –50 85°C –60 25°C –70 HD3 at 600MHz vs PWRADJ Over Temperature HD3 at 600MHz vs VCM Over V+ –30 V+ = 4.75V V+ = 5.0V V+ = 5.25V –50 –60 –50 105°C –60 85°C 25°C –70 –70 –40°C POUT = 11dBm –40 HD3 (dBc) –30 HD3 at 600MHz vs VCM Over Temperature –40°C –80 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G19 HD3 at 700MHz vs VCM Over Temperature 25°C –60 –40°C –30 V+ = 4.75V V+ = 5.0V V+ = 5.25V –50 4 4.5 –60 5 POUT = 11dBm –50 105°C 85°C –60 –70 –70 –80 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –80 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –80 25°C 105°C 35 POUT = 5dBm/TONE ∆FREQ = 1MHz 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G25 OIP3 (dBm) 45 40 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 5 OIP3 at 30MHz vs PWRADJ Over Temperature 55 55 50 50 45 45 25°C –40°C 0.5 6417 G24 OIP3 at 30MHz vs VCM Over V+ 55 85°C 0 6417 G23 OIP3 at 30MHz vs VCM Over Temperature 30 2 2.5 3 3.5 PWRADJ (V) –40 –70 50 1.5 –40°C 6417 G22 OIP3 (dBm) POUT = 11dBm HD3 (dBc) 105°C 1 HD3 at 700MHz vs PWRADJ Over Temperature HD3 at 700MHz vs VCM Over V+ –40 85°C –50 0.5 6417 G21 OIP3 (dBm) HD3 (dBc) –30 POUT = 11dBm –40 0 6417 G20 HD3 (dBc) –30 –80 –80 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 40 POUT = 5dBm/TONE ∆FREQ = 1MHz 35 30 V+ = 4.75V V+ = 5.0V V+ = 5.25V 30 6417 G26 85°C 105°C 40 35 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 25°C –40°C 25 POUT = 5dBm/TONE ∆FREQ = 1MHz 0 0.5 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 5 6417 G27 6417f 10 LTC6417 Typical Performance Characteristics –40°C 25°C 45 OIP3 (dBm) 50 85°C 30 55 POUT = 5dBm/TONE ∆FREQ = 1MHz –40°C 50 45 40 35 OIP3 at 70MHz vs PWRADJ Over Temperature OIP3 at 70MHz vs VCM Over V+ 105°C 45 OIP3 (dBm) 50 55 OIP3 (dBm) 55 OIP3 at 70MHz vs VCM Over Temperature 40 35 30 POUT = 5dBm/TONE ∆FREQ = 1MHz 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 105°C V+ = 4.75V V+ = 5.0V V+ = 5.25V 30 25 POUT = 5dBm/TONE ∆FREQ = 1MHz 0 0.5 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 6417 G29 OIP3 at 100MHz vs VCM Over Temperature 55 55 –40°C 50 85°C 40 35 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G28 25°C 50 4.5 5 6417 G30 OIP3 at 100MHz vs PWRADJ Over Temperature OIP3 at 100MHz vs VCM Over V+ 55 POUT = 5dBm/TONE ∆FREQ = 1MHz –40°C 50 25°C 105°C 35 35 85°C 30 POUT = 5dBm/TONE ∆FREQ = 1MHz OIP3 at 140MHz vs VCM Over Temperature 55 30 25 POUT = 5dBm/TONE ∆FREQ = 1MHz 0 0.5 50 OIP3 (dBm) 40 85°C 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 5 6417 G33 OIP3 at 140MHz vs PWRADJ Over Temperature 55 POUT = 5dBm/TONE ∆FREQ = 1MHz 50 105°C 45 45 35 105°C –40°C 45 OIP3 (dBm) V+ = 4.75V V+ = 5.0V V+ = 5.25V OIP3 at 140MHz vs VCM Over V+ POUT = 5dBm/TONE ∆FREQ = 1MHz 25°C 85°C 40 6417 G32 6417 G31 50 25°C 35 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 55 40 OIP3 (dBc) 30 OIP3 (dBm) OIP3 (dBm) 40 45 OIP3 (dBc) 45 45 40 85°C 25°C 40 –40°C 35 35 105°C V+ = 4.75V V+ = 5.0V V+ = 5.25V 30 30 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G34 6417 G35 30 25 POUT = 5dBm/TONE ∆FREQ = 1MHz 0 0.5 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 5 6417 G36 6417f 11 LTC6417 Typical Performance Characteristics 55 25°C 45 50 –40°C 105°C 30 40 55 POUT = 5dBm/TONE ∆FREQ = 1MHz 50 –40°C 25 85°C 30 0 V+ = 4.75V V+ = 5.0V V+ = 5.25V 55 POUT = 5dBm/TONE ∆FREQ = 1MHz 40 30 20 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 25 45 –40°C 50 POUT = 5dBm/TONE ∆FREQ = 1MHz 25 20 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G43 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 OIP3 (dBc) 25°C 35 105°C 30 V+ = 4.75V V+ = 5.0V V+ = 5.25V 20 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G44 5 –40°C 40 30 105°C 1 POUT = 5dBm/TONE ∆FREQ = 1MHz 45 35 85°C 25 0.5 OIP3 at 500MHz vs PWRADJ Over Temperature 40 OIP3 (dBm) OIP3 (dBm) 50 30 0 6417 G42 OIP3 at 500MHz vs VCM Over V+ POUT = 5dBm/TONE ∆FREQ = 1MHz 5 85°C 105°C 6417 G41 OIP3 at 500MHz vs VCM Over Temperature 35 4.5 25°C 40 30 25°C 4 –40°C 25 6417 G40 2 2.5 3 3.5 PWRADJ (V) 45 35 40 1.5 POUT = 5dBm/TONE ∆FREQ = 1MHz 50 35 45 1 OIP3 at 380MHz vs PWRADJ Over Temperature 105°C 50 0.5 6417 G39 45 OIP3 (dBm) 40 OIP3 (dBm) 30 OIP3 at 380MHz vs VCM Over V+ 35 85°C 105°C 6417 G38 OIP3 at 380MHz vs VCM Over Temperature 25°C V+ = 4.75V V+ = 5.0V V+ = 5.25V 25 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G37 45 25°C 40 35 30 20 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) –40°C 45 35 POUT = 5dBm/TONE ∆FREQ = 1MHz POUT = 5dBm/TONE ∆FREQ = 1MHz 50 OIP3 (dBc) OIP3 (dBm) OIP3 (dBm) 85°C 35 50 55 POUT = 5dBm/TONE ∆FREQ = 1MHz 45 40 25 OIP3 at 240MHz vs PWRADJ Over Temperature OIP3 at 240MHz vs VCM Over V+ OIP3 (dBc) 50 OIP3 at 240MHz vs VCM Over Temperature 85°C 25 20 0 0.5 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 5 6417 G45 6417f 12 LTC6417 Typical Performance Characteristics –40°C 35 30 85°C 25 20 30 15 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) OIP3 (dBm) 45 POUT = 5dBm/TONE ∆FREQ = 1MHz 35 15 85°C 0 0.5 45 POUT = 5dBm/TONE ∆FREQ = 1MHz 30 20 15 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 15 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 15 10 100 130 120 120 SUPPLY CURRENT (mA) P1 dB COMPRESSION (dBm) SUPPLY CURRENT (mA) 300 400 500 FREQUENCY (MHz) 600 700 6417 G52 0.5 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 100 80 60 40 0 4.5 5 Supply Current vs PWRADJ 140 110 100 90 80 20 200 0 6417 G51 Supply Current vs Supply Voltage V+ = 5.25V V+ = 5.0V V+ = 4.75V 12 85°C 105°C 6417 G50 Output 1dB Compression vs Frequency and Supply Voltage 5 30 20 6417 G49 4.5 –40°C 20 14 4 25°C 35 25 16 2 2.5 3 3.5 PWRADJ (V) POUT = 5dBm/TONE ∆FREQ = 1MHz 40 25 18 1.5 OIP3 at 700MHz vs PWRADJ Over Temperature 105°C 20 1 6417 G48 35 30 25 V+ = 4.75V V+ = 5.0V V+ = 5.25V 40 25°C –40°C 85°C 20 OIP3 at 700MHz vs VCM Over V+ OIP3 (dBm) 40 105°C 6417 G47 OIP3 at 700MHz vs VCM Over Temperature 45 V+ = 4.75V V+ = 5.0V V+ = 5.25V 15 0.85 0.95 1.05 1.15 1.25 1.35 1.45 1.55 1.65 VCM (V) 6417 G46 30 25 20 POUT = 5dBm/TONE ∆FREQ = 1MHz 25°C –40°C 35 25 105°C POUT = 5dBm/TONE ∆FREQ = 1MHz 40 OIP3 (dBc) OIP3 (dBm) 35 45 POUT = 5dBm/TONE ∆FREQ = 1MHz 40 25°C OIP3 at 600MHz vs PWRADJ Over Temperature OIP3 at 600MHz vs VCM Over V+ OIP3 (dBc) 40 45 OIP3 (dBm) 45 OIP3 at 600MHz vs VCM Over Temperature 0 1 2 3 4 SUPPLY VOLTAGE (V) 5 6417 G53 70 0 0.5 1 1.5 2 2.5 3 3.5 PWRADJ (V) 4 4.5 5 6417 G54 6417f 13 LTC6417 Typical Performance Characteristics Small Signal Transient Response, Falling Edge with Input Small Signal Transient Response, Falling Edge 62.5mV/ DIV Small Signal Transient Response, Rising Edge 62.5mV/ DIV 20mV/ DIV 62.5mV/ DIV 6417 G55 1.25ns/DIV Differential Input Return Loss (S11) vs Frequency Overdrive Recovery and Overrange Response 0 –60 R = 0Ω R = 23.7Ω DEMO BOARD DC1660B –80 R = 0Ω S12 (dB) S11 (dB) Differential Reverse Isolation (S12) vs Frequency DEMO BOARD DC1660B –10 600mV/ DIV 6417 G57 1.25ns/DIV 6417 G56 1.25ns/DIV –20 R = 23.7Ω –100 –30 10mV/ DIV –40 6417 G58 10ns/DIV 10 100 FREQUENCY (MHz) 1000 –120 10 100 FREQUENCY (MHz) 6417 G60 6417 G59 Differential Forward Gain (S21) vs Frequency 10 Differential Output Return Loss (S22) vs Frequency 0 0 DEMO BOARD DC1660B R = 0Ω LTC6417 Driving LTC2209 16-Bit ADC, 32K Point FFT, fIN = 69.5MHz, –1dBFS, PGA = 0 –30 S22 (dB) S21 (dB) R = 0Ω 0 AMPLITUDE (dBFS) –10 R = 23.7Ω –20 R = 23.7Ω –5 –40 –50 –60 –70 3 –80 –90 –30 2 –100 –10 10 100 FREQUENCY (MHz) 1000 6417 G61 –40 DEMO BOARD DC1660B 10 100 FREQUENCY (MHz) 1000 6417 G62 1 HDR = –92dBc HD3 = –86dBc SFDR = 86dBc SNR = 76.2dB SEE FIGURE 1/TABLE 1 1:4 BALUN fS = 153.6Msps DEMO BOARD DC1685A –10 –20 5 1000 –110 –120 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 6417 G63 6417f 14 LTC6417 Typical Performance Characteristics –20 –30 AMPLITUDE (dBFS) 0 HD2 = –88dBc HD3 = –94dBc SFDR = 88dBc SNR = 75.4dB SEE FIGURE 1/TABLE 1 1:4 BALUN fS = 153.6Msps DEMO BOARD DC1685A –40 –50 –60 –20 –30 –70 –80 2 –90 HD2 = –81dBc HD3 = –80dBc SFDR = 80dBc SNR = 73.3dB SEE FIGURE 1/ TABLE 1 1:4 BALUN fS = 153.6Msps DEMO BOARD DC1685A –10 –40 –50 –60 –70 –80 –30 2 –40 –50 –60 –90 –110 –110 –120 –120 30 40 50 60 FREQUENCY (MHz) 70 80 0 10 20 6417 G64 0 –40 –20 –30 –50 –60 –70 –80 0 –40 –20 –30 –50 –60 –70 –80 –40 –50 –90 –110 –110 –110 –120 –120 80 0 10 6417 G67 –40 –50 –60 –70 –80 –90 –100 –110 –120 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 6417 G70 0 10 20 30 40 50 60 FREQUENCY (MHz) Input Referred Noise Voltage vs Frequency and Noise Figure for the DC1660B with 1:4 Input Balun 20 28 NOISE FIGURE PWRADJ = 5V NOISE FIGURE PWRADJ = 0V NOISE DENSITY PWRADJ = 5V 24 NOISE DENSITY PWRADJ = 0V 20 16 16 12 12 8 8 4 4 24 0 0.001 0.01 0.1 1 10 FREQUENCY (MHz) 100 1k 6417 G71 80 6417 G69 Input Referred Noise Voltage vs Frequency and Noise Figure for the DC1660B with 1:1 Input Balun 28 70 0 24 NOISE FIGURE PWRADJ = 5V NOISE FIGURE PWRADJ = 0V NOISE DENSITY PWRADJ = 5V 20 NOISE DENSITY PWRADJ = 0V 24 20 16 16 12 12 8 8 4 4 0 0.001 0.01 0.1 1 10 FREQUENCY (MHz) 100 1k NOISE FIGURE (dB) AMPLITUDE (dBFS) –30 INPUT REFERRED NOISE VOLTAGE (nV/√Hz) –20 –120 80 NOISE FIGURE (dB) IM3 = –72dBc SEE FIGURE 1/TABLE 1 1:4 BALUN fS = 153.6Msps DEMO BOARD DC1685A 70 INPUT REFERRED NOISE VOLTAGE (nV/√Hz) 0 30 40 50 60 FREQUENCY (MHz) 6417 G68 LTC6417 Driving LTC2209 16-Bit ADC, 64K Point FFT, fIN = 379.5MHz and 380.5MHz, –7dBFS/Tone, PGA = 0 –10 20 80 –80 –100 70 70 –70 –100 30 40 50 60 FREQUENCY (MHz) 30 40 50 60 FREQUENCY (MHz) –60 –100 20 20 IM3 = –75dBc SEE FIGURE 1/ TABLE 1 1:4 BALUN fS = 153.6Msps DEMO BOARD DC1685A –10 –90 10 10 LTC6417 Driving LTC2209 16-Bit ADC, 64K Point FFT, fIN = 269.5MHz and 270.5MHz, –7dBFS/Tone, PGA = 0 –90 0 0 6417 G66 IM3 = –80dBc SEE FIGURE 1/TABLE 1 1:4 BALUN fS = 153.6Msps DEMO BOARD DC1685A –10 AMPLITUDE (dBFS) AMPLITUDE (dBFS) –30 –120 80 LTC6417 Driving LTC2209 16-Bit ADC, 64K Point FFT, fIN = 139.5MHz and 140MHz, –7dBFS/Tone, PGA = 0 0 IM3 = –85dBc SEE FIGURE 1/TABLE 1 1:4 BALUN fS = 153.6Msps DEMO BOARD DC1685A –20 70 6417 G65 LTC6417 Driving LTC2209 16-Bit ADC, 32K Point FFT, fIN = 69.5MHz and 70.5MHz, –7dBFS/Tone, PGA = 0 –10 30 40 50 60 FREQUENCY (MHz) AMPLITUDE (dBFS) 20 3 –80 –110 10 2 –70 –100 0 1 HD2 = –65dBc HD3 = –74dBc SFDR = 65dBc SNR = 71.0dB SEE FIGURE 1/TABLE 1 1:4 BALUN fS = 153.6Msps DEMO BOARD DC1685A –20 –100 –100 LTC6417 Driving LTC2209 16-Bit ADC, 64K Point FFT, fIN = 380MHz, –1dBFS, PGA = 0 –10 3 –90 3 0 1 AMPLITUDE (dBFS) 1 –10 AMPLITUDE (dBFS) 0 LTC6417 Driving LTC2209 16-Bit ADC, 64K Point FFT, fIN = 270MHz, –1dBFS, PGA = 0 LTC6417 Driving LTC2209 16-Bit ADC, 64K Point FFT, fIN = 140MHz, –1dBFS, PGA = 0 0 6417 G72 6417f 15 LTC6417 Pin Functions V+ (Pins 1, 6, 11, 16): Positive Power Supply. Typically 5V. Split supplies are possible as long as the voltage between V+ and GND is 4.75V to 5.25V. Bypass capacitors of 680pF and 0.1µF as close to the part as possible should be used between the supplies. CLHI (Pin 2): High Side Clamp Voltage. The voltage applied to the CLHI pin defines the upper voltage limit of the OUT+ and OUT– pins. This voltage should be set at least 300mV above the upper voltage range of the ADC. On a 5V supply, the CLHI pin will float to a 2.5V default voltage. CLHI has a Thevenin equivalent of approximately 4.8kΩ and can be overdriven by an external voltage. The CLHI pin should be bypassed with a high quality ceramic bypass capacitor of at least 0.01µF. GND (Pins 3, 7, 10, 17, 20, Exposed Pad Pin 21): Negative Power Supply. Normally tied to ground. All pins and the exposed pad must be tied to the same voltage. GND may be tied to a voltage other than ground as long as the voltage between V+ and GND is 4.75V to 5.25V. If the GND pins are not tied to ground, bypass each with 680pF and 0.1µF capacitors as close to the package as possible. The exposed pad must be soldered to the printed circuit board ground plane for good heat transfer. NC (Pins 4, 13): No Connection. These pins are not connected internally. PWRADJ (Pin 5): Power Adjust Voltage. The voltage applied to this pin scales the bias current internal to the LTC6417. The PWRADJ pin will float to a 1.6V default voltage. PWRADJ has a Thevenin equivalent resistance of approximately 14.5k and can be overdriven by an external voltage. The PWRADJ pin should be bypassed with a high quality ceramic bypass capacitor of at least 0.01µF. IN+, IN– (Pin 8, Pin 9): Non-inverting and inverting input pins of the buffer, respectively. These pins are high impedance, approximately 9.5k. If AC-coupled, these pins will self bias to the voltage applied to the VCM pin. SHDN (Pin 12): This pin puts the LTC6417 in sleep mode when pulled high. If no voltage is applied to the SHDN pin, it floats down to the same potential as GND. VOR (Pin 14): Overrange Output. This pin, by default at 3.4V, will be pulled down to GND, when one or both input signals go beyond the minimum or maximum swing set by the CLHI and VCM pins. VCM (Pin 15): This pin sets the output common mode voltage seen at OUT+ and OUT– by driving IN+ and IN– through a buffer with a high output resistance of 9.5k. The VCM pin has a Thevenin equivalent resistance of approximately 2.7k and can be overdriven by an external voltage. If no voltage is applied to VCM, it will float to a default voltage of approximately 1.25V on a 5V supply. The VCM pin should be bypassed with a high quality ceramic bypass capacitor of at least 0.01µF. OUT–, OUT+ (Pin 18, Pin 19): Outputs. 6417f 16 LTC6417 DC Test Circuit Schematic V+ 1, 6, 11, 16 V+ 15 VCM VCM 2 19 CLHI CLHI + – VINDIFF = IN – IN 8 OUT+ + + IN LTC6417 + – IN 9 VINCM = IN + IN – IN– IN– OUT 2 5 18 PWRADJ PWRADJ VOR 14 SHDN VOR 12 – OUT CLOAD RLOAD 6417 TC OUT+ VOUTDIFF = OUT+ – OUT– + – VOUTCM = OUT + OUT 2 3, 7, 10, 17, 20, 21 Block Diagram LTC6417 Simplified Schematic V+ I1 IN QN3 QP1 ×1 – ×2 OVER RANGE DETECT QN1 QP3 + CLHI I2 VOR OUT+ CLLO + VCM ×1 QN2 QP4 IN– QN4 QP2 OUT– PWRADJ SHDN GND REFERENCE AND BIAS CONTROL I3 I4 6417 BD 6417f 17 LTC6417 Applications Information Circuit Operation Input Impedance and Matching The LTC6417 is a low noise and low distortion fully differential unity gain ADC driver with a –3dB bandwidth spanning DC to 1.6GHz, a differential input impedance of 18.5kΩ, and a differential output impedance of 3Ω. The LTC6417 is composed of a fully differential buffer with output common mode voltage control circuitry and high speed voltage-limiting clamps at the output. Lowpass or bandpass filters are easily implemented with just a few external components. The LTC6417 is very flexible in terms of I/O coupling. It can be AC- or DC-coupled at the inputs, the outputs or both. When using the LTC6417 with DC-coupled inputs, best performance is obtained with an input common mode voltage between 1V and 1.5V. For AC-coupled operation, the LTC6417 will take the voltage applied to the VCM pin and use it to bias the inputs so that the output common mode voltage equals VCM, thus no external circuitry is needed. The VCM pin has been designed to directly interface with the VCM pin found on Linear Technology’s high speed ADC families. The LTC6417 has a high differential input impedance of 18.5kΩ. The differential inputs may need to be terminated to a lower value impedance, e.g. 50Ω, in order to provide an impedance match for the source. Figure 1 shows input matching and single-ended to differential conversion using a 1:1 balun, while Figure 2 shows a similar circuit using a 1:4 balun to achieve an additional 6dB of voltage gain. These circuits provide a wideband impedance match. The balun and matching resistors must be placed close to the input pins in order to minimize the rejection due to input mismatch. In Figures 1 and 2, the capacitor centertapping the two input termination resistors improves high frequency common mode rejection. As an alternative to this wideband approach, a narrowband impedance match can be used at the inputs of the LTC6417 for frequency selection and/or noise reduction. T1 0.1µF MABA-007159-000000 VIN + – 0.1µF 4 • 1:1 • 5 50Ω IN+ 19 OUT+ 24.9Ω 0.1µF 1 3 8 LTC6417 0.1µF 24.9Ω 9 IN– 18 OUT– 6417 F01 Figure 1. Input Termination for Differential 50Ω Input Impedance Using a 1:1 Balun 4 50Ω VIN + – T1 TCM4-19+ 3 0.1µF 1 OUT+ 19 LTC6417 0.1µF 6 IN+ 100Ω 0.1µF 2 0.1µF 8 100Ω 9 IN– OUT– 18 6417 F02 Figure 2. Input Termination for Differential 50Ω Input Impedance Using a 1:4 Balun 6417f 18 LTC6417 Applications Information The noise figure of the LTC6417 application circuit also depends upon the input termination. For example, the input 1:4 balun in Figure 2 improves noise figure by adding 6dB of voltage gain at the inputs. A trade-off between gain and noise is obvious when constant noise figure circle and constant gain circle are plotted within the same input Smith Chart. This technique can be used to determine the optimal source impedance for a given gain and noise requirement. Output Match and Filter The LTC6417 provides an output resistance of 1.5Ω at each output. In most cases, the LTC6417 can be used to drive an ADC without back termination but for testing purposes, Figure 3 shows the LTC6417 driving a differential 50Ω load impedance using a 1:1 balun. If output 8 IN+ OUT+ 18 0Ω 0.1µF matching for the 1:1 balun is desired, resistors of 23.7Ω should be inserted in series with each LTC6417 output. This is shown in Figure 4 where the LTC6417 is driving a differential 100Ω load impedance. As mentioned above, the LTC6417 can drive an ADC without external output impedance matching, but improved performance can usually be obtained with the addition of a few components. Figure 5 shows a 6th order bandpass filter with a 148MHz center frequency, –3dB points of 85MHz and 210MHz used for driving the LTC2209 16-bit ADC. In the passband the filter has less than 1 dB ripple. This higher order filter has a sharp roll-off outside its passband, therefore it rejects noise and suppresses distortion components in its stopband. To double the filter center frequency, halve the capacitor and inductor values, and maintain resistor values; this also doubles the filter bandwidth. T2 MABA-007159-000000 50Ω LTC6417 IN– OUT– 19 0Ω • • 9 0.1µF 6417 F03 Figure 3. LTC6417 with No Back Termination Driving a 50Ω Load Using a 1:1 Balun 8 IN+ 19 OUT+ 23.7Ω 0.1µF T2 MABA-007159-000000 3 4 LTC6417 IN– 18 OUT– 23.7Ω 0.1µF 1 • • 9 50Ω 5 6417 F04 Figure 4. Output Termination for Differential 50Ω Load Using a 1:1 Balun 6417f 19 LTC6417 Applications Information 3.3V 5V 680pF 0.1µF C43 27pF 2.2µF 1,6, 11,16 T1 WBC4-14LB 4 3 2 50Ω + – 6 • 0.01µF • 1 100Ω 100Ω 0.01µF 8 5 V+ PWRADJ IN+ LTC6417 19 OUT+ OUT – V IN– 18 VCM OR 14 SHDN 15 GND 12 1k 3,7,10, 17, 20,21 9 E3 75nH R36 60.4Ω 2 CLHI E1 51nH R42 300Ω 0Ω R12 60.4Ω 0Ω C44 27pF C45 18pF C41 12pF E5 51nH 10Ω C40 12pF R53 120Ω C10 12pF E2 51nH R43 300Ω E3 75nH 10Ω AIN+ AIN– LTC2209 VCM C46 18pF 16 PGA = 0 CLOCK (153.6MHz) 6417 F05 2.2µF Figure 5. DC1685A Simplified Schematic with Suggested Bandpass Filter for Driving an LTC2209 16-Bit ADC at 140MHz Table 1. Bandpass Filter Component Values for Different Input Frequencies INPUT FREQUENCIES COMPONENTS 70MHz 140MHz 270MHz 380MHz R12 = R36 60.4Ω 60.4Ω 60.4Ω 60.4Ω C43 = C44 56pF 27pF 15pF 12pF E1 = E2 100nH 51nH 27nH 18nH C41 47pF 12pF 12pF 10pF C10 = C40 13pF 12pF 3.3pF 2.7pF E5 100nH 51nH 27nH 18nH R42 = R43 300Ω 300Ω 300Ω 300Ω R53 120Ω 120Ω 120Ω 120Ω C45 = C46 39pF 18pF 10pF 8.2pF E3 = E4 150nH 75nH 39nH 27nH 6417f 20 LTC6417 Applications Information Output Common Mode Adjustment For AC-coupled applications, the output common mode voltage is set by the VCM pin. An internal buffer, as shown in Figure 6, couples the voltage on the VCM pin to the inputs via high impedance resistors. Because the input common mode voltage is approximately the same as the output common mode voltage, both are approximately equal to the voltage applied to the VCM pin. For DC-coupled applications, the internal VCM is overdriven by the input signal. The VCM pin has a Thevenin equivalent resistance of 2.7k and can be overdriven by an external voltage. The VCM pin floats to a default voltage of 1.25V on a 5V supply. The output common mode voltage is capable of tracking VCM in a range from 0.29V to 2.25V on a 5.0V supply. The VCM pin can be floated, but it should always be bypassed close to the LTC6417 with a 0.1µF bypass capacitor to GND. When interfacing with A/D converters such as the LTC22xx families, the VCM pin can be connected to the VCM output pin of the ADC, as shown in Figure 5. Clamping, the CLHI Pin and the VCM Pin The CLHI pin is used to set the high side clamp voltage of the high speed internal circuitry. This limits the single-ended maximum and minimum voltage excursion at each of the outputs. This feature is extremely important in applications with input signals having very large peak-to-average ratios such as cellular base station receivers. Internal circuitry generates a symmetric low side clamp voltage with respect to the common mode voltage VCM (Figures 7 and 8). The LTC6417 clamp control circuitry features two additional mechanisms. First, internally imposed maximum swing of 2.5V and minimum swing of 0.2V ensure that the transistors do not go into deep saturation. This ensures a quick recovery after the clamps are released. Second, if CLHI voltage is less than VCM, internal CLLO starts to track CLHI. This limits output swing and protects output transistors. Since the clamp response is on the order of 5ns to clamp and 1ns to release, clamp circuit becomes less effective at frequencies beyond 160MHz. LTC6417 V+ IN+ 1.5Ω OUT+ 1.5Ω OUT– x1 10.8k 9.25k VCM 3.6k x1 9.25k IN– x1 GND 6417 F06 Figure 6. LTC6417 Internal Topology Showing the Common Mode Buffer Biasing the Inputs LTC6417 V+ 9.6k CLHI 9.6k x1 – + VCM CLHI (INT) CLLO (INT) x2 GND 6417 F07 Figure 7. Internal Circuitry Generating Symmetric Clamp Voltages with Respect to VCM CLHI VCM 6417 F08 CLLO Figure 8. Symmetric High- and Low-Side Clamp Voltages with Respect to VCM 6417f 21 LTC6417 Applications Information If a very large signal arrives at the LTC6417, the voltages applied to the CLHI and VCM pins will determine the maximum and minimum output swing. Once the input signal returns to the normal operating range, the LTC6417 returns to linear operation within 2ns. For DC-coupled operation, the common mode of the input signals might be different than the voltage on the VCM pin. The minimum swing will still be set by the voltages applied to the VCM and CLHI pins. CLHI is a high impedance input. It has an input impedance of 4.8k. On a 5V supply, CLHI self-biases to 2.5V. To limit the signal swing to a subsequent stage’s power supply, e.g. an ADC such as the LTC2165, simply connect CLHI to the positive supply pin of the LTC2165. The CLHI pin should be bypassed with a 0.1µF capacitor as close to the LTC6417 as possible. The VOR Pin The VOR, overrange pin signals an overrange condition when one or both inputs exceed the minimum or maximum signal swing limits set by the CLHI and VCM pins. The LTC6417 VOR pin can be used by a control system to limit the input power dynamically. This is very useful in applications where the overload response of the complete system would be too slow. The VOR pin, as shown in Figure 9, is internally connected to a current source sourcing 2mA, plus an internal 20k resistor pull-down to GND. An internal clamp limits the maximum output to 3.4V. As soon as one of the inputs goes beyond the limits, and therefore engages one of the clamps, the output current, hence, the VOR voltage goes to zero. The dynamic response of the VOR pin can be adjusted with an external resistor and an optional external capacitor. For a high speed operation, add a 50Ω resistor from VOR to GND, resulting in a high speed signal with 100mV swing. The PWRADJ Pin The voltage applied to the PWRADJ pin scales the supply current and performance of the LTC6417. This is useful for reducing power consumption in applications where linearity of the LTC6417 exceeds the linearity of the other components in the system; hence LTC6417’s linearity can be derated without effecting system performance. PWRADJ is a high impedance input. It has an input impedance of 14.5k. On a 5V supply, PWRADJ self-biases to 1.6V. For full power, simply connect PWRADJ to the positive supply V+. For minimum power, short the PWRADJ pin to GND. The PWRADJ pin should be bypassed with a 0.1µF capacitor as close to the LTC6417 as possible. LTC6417 performance vs PWRADJ can be found in the graphs. LTC6417 The SHDN Pin V+ 2mA VOR ICL 20k GND 6417 F09 Figure 9. LTC6417 Internal Topology Showing VOR Pin with Pull-Down Resistor and Clamp When pulled high, the SHDN pin puts the LTC6417 in sleep mode, significantly reducing supply current. SHDN is a high impedance input. It has an input impedance of 10.5kΩ. If the SHDN pin is not driven with an external voltage, it floats down to the same potential as GND, keeping the LTC6417 enabled. The SHDN pin should be bypassed with a 0.1µF capacitor as close to the LTC6417 as possible. In sleep mode, the input and output stages are turned off, but the input and output clamps are kept alive to protect the part against overvoltage. The supply current in sleep mode is only 24mA, instead of the typical 125mA. But should the clamps turn on, the current drawn from the supply can be as high as 180mA. 6417f 22 LTC6417 Applications Information This can be avoided by following a few precautions when putting the LTC6417 in sleep mode: • Do not force the outputs below the inputs, this will turn the output stages on. • Either float CLHI or tie it to VCC. This will allow a wider signal range at the inputs before the clamps are activated. Noise figure (NF) is calculated from the ratio of these noise powers: e2no NF = 10log 1+ 2 e no(mR ) S • Maintain the inputs below CLHI or 2.5V whichever is lower, otherwise the input clamps will be activated. • Do not short VCM or the outputs to GND, in either case the output clamps will turn on. Current drawn from the supply can be as high as 180mA. 1:m TRANSFORMER RS LTC6417 RT • Float the outputs if possible. The outputs will be pulled down by internal resistors to VCM. 6417 F10 Heeding these precautions will protect the LTC6417 as well any part it is driving, while maintaining a low current consumption in sleep mode. Figure 10. LTC6417 with a Transformer Noise and Noise Figure The LTC6417’s differential input referred voltage and current noise densities are 1.5nV/√Hz and 4.3pA/√Hz, respectively. Before presenting a noise model, the circuit with the transformer in Figure 10 will be simplified. In Figure 11, the circuit is redrawn with the source impedance reflected to the secondary side of the transformer. The source impedance is multiplied by the impedance ratio m of the transformer. In Figure 12, noise sources associated with the amplifier and resistors have been added. Based on this noise model of the LTC6417, the total output noise power excluding the noise contribution of the source is: ( + (i e no2 = e 2ni + i ni • REQ = e 2ni ni • REQ ) ) 2 mRS LTC6417 RT 6417 F11 Figure 11. Source Resistance Referred to the Secondary eni2 mRS i2mRS RT i2RT eno2 i2ni LTC6417 + i 2R T • R2EQ 2 + 4kT 2 • R EQ RT 6417 F12 Figure 12. LTC6417 Simplified Noise Model where R EQ = mRS ||RT is the equivalent impedance seen at the input of the LTC6417. The output noise power due to the noise of source resistance is given by: e no(mRS )2 = i 2mRS • R2EQ = 4kT • R2EQ mRS 6417f 23 LTC6417 Applications Information In most cases the termination resistor will be matched to the source resistance, e.g. RT = mRS. For the LTC6417 with a wide-band terminated transformer, a plot of output and input noise density and NF versus termination resistor is shown in Figure 13. To get the best noise performance in the system, use the LTC6417 matched to a transformer with high impedance ratio. Although the output noise density will be higher, noise figure will improve because of the additional gain realized in the transformer. An impedance ratio greater than 8 is not recommended, as the increased termination resistance with the LTC6417 input capacitance will limit signal bandwidth. Consult Table 2 for a quick estimate of the LTC6417’s output noise density and NF for different transformer impedance ratios. Measured NF numbers will be higher as the simple noise model does not take the insertion loss in the transformer into account. Table 2. Output Noise Density and NF of the LTC4617 with a Wide-Band Terminated Transformer, RS = 50Ω TRANSFORMER TERMINATION IMPEDANCE RESISTOR RT RATIO m (Ω) OUTPUT NOISE DENSITY eno (nV/√Hz) NF (dB) 50 1.0 1.57 11.2 2 100 1.4 1.64 8.9 4 200 2.0 1.80 7.0 8 400 2.8 2.14 5.9 2.1 1.9 10 1.7 9 1.5 8 1.3 7 1.1 6 0.9 5 0.7 50 100 150 200 250 300 350 TERMINATION RESISTANCE (Ω) The LTC6417 has not been designed to convert singleended signals to differential signals. A single-ended input signal can be converted to a differential signal via a balun connected to the inputs of the LTC6417. Figure 5 shows the LTC6417 driven by a 1:4 transformer which provides 6dB of voltage gain while also performing a single-ended to differential conversion. Power Supply Considerations 11 NF (dB) eno (nV/√Hz) 12 NF eno eni The LTC6417 has been specially designed to interface directly with high speed A/D converters. It is possible to drive the ADC directly from the LTC6417. In practice, however, better performance may be obtained by adding a few external components at the output of the LTC6417. Figure 5 shows the LTC6417 driving an LTC2209 16-bit ADC. The differential outputs of the LTC6417 are bandpass filtered, then drive the differential inputs of the LTC2209. In many applications, a filter like this is desirable to limit the wideband noise of the amplifier. This is especially true in high performance 16-bit designs. The minimum recommended network between the LTC6417 and the ADC is simply two 10Ω series resistors, which are used to help eliminate resonances associated with the stray capacitance of PCB traces and the stray inductance of the internal bond wires at the ADC input pins and the driver output pins. Single-Ended Signals GAIN (V/V) 1 2.3 Interfacing the LTC6417 to A/D Converters 4 400 6417 F13 Figure 13. LTC4617 Output and Input Noise Density and NF vs Termination Resistance For best linearity, the LTC6417 should have a positive supply of V+ = 5V. For ESD protection, the LTC6417 has an internal edge-triggered supply voltage clamp. The timing mechanism of the clamp enables the LTC6417’s protection circuit during ESD events. This internal clamp can also be activated by voltage overshoot and rapid slew rate on the positive supply V+ pin. The LTC6417 should not be hot-plugged into a powered socket because there is a risk of activating this internal ESD clamp circuit. Bypass capacitors of 680pF and 0.1µF should be connected to the V+ pin, as close as possible to the LTC6417. Interfacing the LTC6417 with Active Mixers for Ultrawide IF Bandwidth The LTC6417 is an excellent interface amplifier for use with active downconverting mixers like the LTC5567. By using 6417f 24 LTC6417 Applications Information the LTC6417 as a post-amplifier for the LTC5567, it is possible to achieve IF bandwidths in excess of 500MHz, while adding bandpass filtering. A key to achieving this extremely wide IF bandwidth is the use of pre-emphasis inductors in series with the LTC6417 inputs to compensate for the inherent rolloff caused by the LTC6417 input capacitance interacting with the interface impedance. In the example seen in Figure 14, a value of 33nH for each pre-emphasis inductor gives excellent wideband performance. Figure 15 shows performance for various values of L. For L = 33nH, overall conversion gain remains within 1dB from 90MHz to 590MHz, resulting in 500MHz of IF bandwidth. demonstration circuit for the LTC6417. The board layout and the schematic are shown in Figures 16 and 17. These circuits include a 1:4 input balun and a 1:1 output balun for single-ended-to-differential conversion, allowing direct analysis using a 2-port network analyzer. Including the input and output baluns, the –3dB bandwidth is approximately 600MHz. A 1:4 input balun before the LTC6417 inputs provides 6dB of voltage gain, but results in better noise figure performance compared to a 1:1 input balun. Noise figure measurements for both input baluns can be found in the graphs. Test circuit B is DC1685A. It consists of an LTC6417 driving an LTC2209 16-bit 153.6Msps ADC. It is intended for use in conjunction with DC890B (computer interface board) and proprietary Linear Technology evaluation software to evaluate the performance of both parts together. Both the DC1685A board layout and the schematic can be seen Figures 18 and 19. Test Circuits Due to the fully differential design of the LTC6417 and its usefulness in applications both with and without ADCs, two test circuits have been used to generate the information in this data sheet. Test circuit A is DC1660B, a two-port LO 1.65GHz 1nF IF+ LTC5567 249Ω RF 1.69GHz TO 2.39GHz L 390n VCC 10nF 249Ω 390n IF– 23.2Ω 127Ω 1nF 1:1 IFOUT 50Ω LTC6417 127Ω L 23.2Ω 1nF 1nF 6417 F14 Figure 14 2 L = 33nH 1 L = 18nH 0 GC (dB) –1 LPF –2 L = 0nH –3 –4 –5 –6 –7 40 140 240 340 440 540 IF FREQUENCY (MHz) 640 740 6417 F15 Figure 15 6417f 25 LTC6417 Applications Information Figure 16. Demo Board DC1660B Layout 6417f 26 A B C D J2 C24 C23 OPT 0603 TCM4-19+ T1 3 2 1 V+ 5 1. ALL RESISTORS AND CAPACITORS ARE 0402 R5 0 C18 680pF C15 0.1uF R4 0 C16 680pF 10 9 8 7 GND IN- IN+ GND U1 LTC6417CUDC CUSTOMER NOTICE V+ C13 0.1uF R6 100 R2 100 C4 0.1uF GND GND OUT- OUT+ GND 4 C21 0.1uF R8 OPT 2 SCALE = NONE DATE: N/A SIZE C9 0.1uF 2 C3 0.1uF 5 DATE 09-12-11 C11 0.1uF 0603 E1 J4 J3 GND VCM OUT- OUT+ V+ 4.75V - 5.25V C6 OPT 0603 E3 E2 C20 0.1uF V+ JOHN C. DEMO CIRCUIT 1660B LTC6417CUDC ADC BUFFER 1 SHEET 1 OF 1 2 REV. 1630 McCarthy Blvd. Milpitas, CA 95035 Phone: (408)432-1900 www.linear.com Fax: (408)434-0507 LTC Confidential-For Customer Use Only 1 Monday, September 12, 2011 IC NO. V+ C14 0.1uF 2 1 APPROVED T2 C5 MABA-007159-000000 0.1uF 3 4 C2 680pF 2ND PROTOTYPE DESCRIPTION REVISION HISTORY TECHNOLOGY REV 2 JOHN C. TITLE: SCHEMATIC LT C22 680pF R3 0 R7 OPT R1 0 __ ECO Figure 17. Demo Board DC1660B Schematic (Test Circuit A) 3 THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS. 21 17 18 19 20 APPROVALS LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO PCB DES. VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APP ENG. APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. C10 0.1uF C7 0.1uF V+ NOTE: UNLESS OTHERWISE SPECIFIED OR J5 4 5 C1 0.1uF C17 0.1uF C19 0.1uF C12 0.1uF 0603 C8 OPT 0603 0.1uF E4 SHUT E7 DOWN IN- IN+ J1 PWRADJ CL HI 11 E5 6 V+ V+ 5 12 NC 13 PWRADJ 3 14 OR 4 15 SHUTDOWN 4 NC 3 GND 2 CL HI VCM 1 V+ V+ 16 5 A B C D LTC6417 Applications Information 6417f 27 LTC6417 Applications Information Figure 18. Demo Board DC1685A Layout 6417f 28 A B C D 5 4 3 2 1 TECHNOLOGY 1 2 Figure 19. Demo Board DC1685A Schematic (Test Circuit B) 3 4 5 A B C D LTC6417 Applications Information 6417f 29 A B C D E 5 4 3 2 1 1 TECHNOLOGY 2 3 Figure 19 (Continued). Demo Board DC1685A Schematic (Test Circuit B) 4 30 5 A B C D E LTC6417 Applications Information 6417f LTC6417 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UDC Package 20-Lead Plastic QFN (3mm × 4mm) (Reference LTC DWG # 05-08-1742 Rev Ø) 0.70 ±0.05 3.50 ± 0.05 2.10 ± 0.05 1.50 REF 2.65 ± 0.05 1.65 ± 0.05 PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC 2.50 REF 3.10 ± 0.05 4.50 ± 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 3.00 ± 0.10 0.75 ± 0.05 1.50 REF 19 R = 0.05 TYP PIN 1 NOTCH R = 0.20 OR 0.25 × 45° CHAMFER 20 0.40 ± 0.10 1 PIN 1 TOP MARK (NOTE 6) 4.00 ± 0.10 2 2.65 ± 0.10 2.50 REF 1.65 ± 0.10 (UDC20) QFN 1106 REV Ø 0.200 REF 0.00 – 0.05 R = 0.115 TYP 0.25 ± 0.05 0.50 BSC BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 6417f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 31 LTC6417 Typical Application DC1685A Simplified Schematic with Suggested Output Termination for Driving an LTC2209 16-Bit ADC at 140MHz 3.3V 5V 680pF 0.1µF 2.2µF C43 27pF 1,6, 11,16 T1 WBC4-14LB 4 3 2 50Ω + – 6 • 0.01µF • 1 8 100Ω 100Ω 0.01µF 5 V+ PWRADJ IN+ LTC6417 19 OUT+ OUT – V IN 18 VCM OR 14 SHDN 15 GND 12 1k 3,7,10, 17, 20,21 9 E3 75nH R36 60.4Ω 2 CLHI E1 51nH R12 60.4Ω – C44 27pF C45 18pF R42 300Ω C41 12pF E5 51nH E2 51nH 10Ω C40 12pF C10 12pF R53 120Ω R43 300Ω E3 75nH 10Ω AIN+ AIN– LTC2209 VCM C46 18pF 16 PGA = 0 CLOCK (153.6MHz) 6417 TA02 2.2µF Related Parts PART NUMBER DESCRIPTION COMMENTS Fixed Gain IF Amplifiers/ADC Drivers LTC6400-8/LTC6400-14/ 1.8GHz Low Noise, Low Distortion Differential LTC6400-20/LTC6400-26 ADC Drivers LTC6420-20 Dual 1.8GHz Low Noise, Low Distortion Differential ADC Drivers LTC6401-8/LTC6401-14/ 1.3GHz Low Noise, Low Distortion Differential LTC6401-20/LTC6401-26 ADC Drivers LTC6421-20 Dual 1.3GHz Low Noise, Low Distortion Differential ADC Drivers IF Amplifiers/ADC Drivers with Variable Gain LTC6412 800MHz, 31dB Range Analog-Controlled VGA LT5554 High Dynamic Range 7-Bit Digitally Controlled IF VGA/ADC Driver LT5514 Ultra-Low Distortion IF Amplifier/ADC Driver with Digitally Controlled Gain LT5524 Low Distortion IF Amplifier/ADC Driver with Digitally Controlled Gain Baseband Differential Amplifiers LT6416 2GHz Low Noise Differential 16-Bit ADC Buffer LTC6409 10GHz 1.1nV√Hz ADC Driver LTC6406 3GHz Rail-to-Rail Input Differential Amplifier/ ADC Driver LTC6404-1/LTC6404-2/ Low Noise Rail-to-Rail Output Differential LTC6404-4 Amplifier/ADC Driver LTC6403-1 Low Noise Rail-to-Rail Output Differential Amplifier/ADC Driver ADCs LTC2209 16-Bit 160Msps ADC LTC2208 16-Bit 130Msps ADC –71dBc IM3 at 240MHz 2VP-P Composite, IS = 90mA, AV = 8dB, 14dB, 20dB, 26dB Dual Version of the LTC6400-20, AV = 8dB, 14dB, 20dB, 26dB –74dBc IM3 at 140MHz 2VP-P Composite, IS = 50mA, AV = 8dB, 14dB, 20dB, 26dB Dual Version of the LTC6401-20, AV = 8dB, 14dB, 20dB, 26dB Continuously Adjustable Gain Control, –14dB to 17dB Linear-in-dB Gain Range OIP3 = 46dBm at 200MHz, Gain Range 1.725 to 17.6dB 0.125dB Steps OIP3 = 47dBm at 100MHz, Gain Range 10.5dB to 33dB 1.5dB Steps OIP3 = 40dBm at 100MHz, Gain Range 4.5dB to 37dB 1.5dB Steps –84dBc IM3 at 160MHz 2VP-P Composite, AV = 1, en = 1.8nV/√Hz, 42mA AC- or DC-Coupled 0MHz to 100MHz –65dBc IM3 at 50MHz 2VP-P Composite, Rail-to-Rail Inputs, en = 1.6nV/√Hz, 18mA 16-Bit SNR and SFDR at 10MHz, Rail-to-Rail Outputs, en = 1.5nV/√Hz, LTC6404-1 is Unity-Gain Stable, LTC6404-2 is Gain-of-2 Stable 16-Bit SNR and SFDR at 3MHz, Rail-to-Rail Outputs, en = 2.8nV/√Hz 77.3dBFS Noise Floor, 100dB SFDR 78dBFS Noise Floor, 100dB SFDR 6417f 32 Linear Technology Corporation LT 0712 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2012