IDT709199L HIGH-SPEED 128K x 9 SYNCHRONOUS PIPELINED DUAL-PORT STATIC RAM Features ◆ ◆ ◆ ◆ ◆ ◆ ◆ True Dual-Ported memory cells which allow simultaneous access of the same memory location High-speed clock to data access – Commercial: 7.5/9/12ns (max.) Low-power operation – IDT709199L Active: 1.2W (typ.) Standby: 2.5mW (typ.) Flow-Through or Pipelined output mode on either Port via the FT/PIPE pins Counter enable and reset features Dual chip enables allow for depth expansion without additional logic ◆ ◆ ◆ Full synchronous operation on both ports – 4ns setup to clock and 0ns hold on all control, data, and address inputs – Data input, address, and control registers – Fast 7.5ns clock to data out in the Pipelined output mode – Self-timed write allows fast cycle time – 12ns cycle time, 83MHz operation in Pipelined output mode TTL- compatible, single 5V (±10%) power supply Industrial temperature range (–40°C to +85°C) is available for selected speeds Available in a 100-pin Thin Quad Flatpack (TQFP) package Functional Block Diagram R/WL OEL R/WR OER CE0L CE1L FT/PIPEL 0/1 1 0 0 I/O0L - I/O8L 1 0/1 FT/PIPER I/O0R - I/O8R I/O Control I/O Control A16L A0L CLKL ADSL CNTENL CNTRSTL CE0R CE1R 1 0 0/1 1 0 0/1 A16R Counter/ Address Reg. MEMORY ARRAY Counter/ Address Reg. A0R CLKR ADSR CNTENR CNTRSTR 4847 drw 01 JANUARY 2001 1 ©2000 Integrated Device Technology, Inc. DSC-4847/3 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Description The IDT709199 is a high-speed 128K x 9 bit synchronous DualPort RAM. The memory array utilizes Dual-Port memory cells to allow simultaneous access of any address from both ports. Registers on control, data, and address inputs provide minimal setup and hold times. The timing latitude provided by this approach allows systems to be designed with very short cycle times. With an input data register, the IDT709199 has been optimized for applications having unidirectional or bidirectional data flow in bursts. An automatic power down feature, controlled by CE0 and CE1, permits the on-chip circuitry of each port to enter a very low standby power mode. Fabricated using IDT’s CMOS high-performance technology, these devices typically operate on only 1.2W of power. NC NC A6L A5L A4L A3L A2L A1L A0L CNTENL CLKL ADSL GND GND ADSR CLKR CNTENR A0R A1R A2R A3R A4R A5R A6R NC Pin Configurations(1,2,3) Index NC NC A7L A8L A9L A10L A11L A12L A13L A14L A15L A16L VCC NC NC NC NC CE0L CE1L CNTRSTL R/WL OEL FT/PIPEL NC NC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 2 74 3 73 4 72 1 5 71 6 7 70 69 8 68 9 10 67 11 IDT709199PF PN100-1(4) 66 100-Pin TQFP Top View(5) 63 12 13 14 65 64 62 15 61 16 17 60 18 59 58 19 57 20 56 21 55 22 23 54 53 24 52 51 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 NC NC A7R A8R A9R A10R A11R A12R A13R A14R A15R A16R GND NC NC NC NC CE0R CE1R CNTRSTR R/WR OER FT/PIPER GND NC GND I/O8L I/O7L I/O6L I/O5L I/O4L I/O3L I/O2L GND I/O1L I/O0L VCC GND I/O0R I/O1R I/O2R VCC I/O3R I/O4R I/O5R I/O6R I/O7R I/O8R NC NC 4847 drw 02 NOTES: 1. All VCC pins must be connected to power supply. 2. All GND pins must be connected to ground. 3. Package body is approximately 14mm x 14mm x 1.4mm 4. This package code is used to reference the package diagram. 5. This text does not indicate orientation of the actual part-marking. 2 6.42 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Pin Names Left Port Right Port Names CE0L, CE1L CE0R, CE1R Chip Enables R/WL R/WR Read/Write Enable OEL OER Output Enable A0L - A16L A0R - A16R Address I/O0L - I/O8L I/O0R - I/O8R Data Input/Output CLK L CLKR Clock ADSL ADSR Address Strobe CNTENL CNTENR Counter Enable CNTRSTL CNTRSTR Counter Reset FT/PIPEL FT/PIPER Flow-Through/Pipeline VCC Power GND Ground 4847 tbl 01 Truth Table IRead/Write and Enable Control(1,2,3) OE CLK CE0 CE1 R/W I/O0-8 X ↑ H X X High-Z Deselected—Power Down X ↑ X L X High-Z Deselected—Power Down X ↑ L H L DATA IN Write L ↑ L H H DATAOUT Read H X L H X High-Z Mode Outputs Disabled 4847 tbl 02 NOTES: 1. "H" = VIH, "L" = VIL, "X" = Don't Care. 2. ADS, CNTEN, CNTRST = X. 3. OE is an asynchronous input signal. Truth Table IIAddress Counter Control(1,2,6) Address Previous Address Addr Used CLK ADS CNTEN CNTRST I/O(3) X X 0 ↑ X X L DI/O(0) Counter Reset to Address 0 X H DI/O(n) External Address Utilized H DI/O(p) External Address Blocked—Counter Disabled (Ap reused) H DI/O(p+1) An X An ↑ L An Ap Ap ↑ H Ap + 1 ↑ X Ap H (4) H L (5) Mode Counter Enable—Internal Address Generation NOTES: 1. "H" = VIH, "L" = VIL, "X" = Don't Care. 2. CE0 and OE = VIL; CE1 and R/W = VIH. 3. Outputs configured in Flow-Through Output mode: if outputs are in Pipelined mode the data out will be delayed by one cycle. 4. ADS is independent of all other signals including CE0 and CE1. 5. The address counter advances if CNTEN = V IL on the rising edge of CLK, regardless of all other signals including CE0 and CE1. 6. While an external address is being loaded (ADS = VIL), R/W = VIH is recommended to ensure data is not written arbitrarily. 6.42 3 4847 tbl 03 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Recommended Operating Recommended DC Operating (1) Temperature and Supply Voltage Conditions Grade Commercial Industrial Symbol Ambient Temperature(2) GND Vcc 0OC to +70OC 0V 5.0V + 10% -40OC to +85OC 0V 5.0V + 10% Parameter VCC Supply Voltage GND Ground VIH Input High Voltage Min. Typ. Max. Unit 4.5 5.0 5.5 V 0 0 0 V 2.2 ____ (1) 6.0 V 4847 tbl 04 NOTES: 1. Industrial temperature: for specific speeds, packages and powers contact your sales office. 2. This is the parameter TA. This is the "instant on" case temperature. (2) V TERM Rating Terminal Voltage with Respect to GND Commercial & Industrial Unit -0.5 to +7.0 V -0.5 0.8 V 4847 tbl 05 NOTES: 1. VTERM must not exceed V cc + 10%. 2. VIL > -1.5V for pulse width less than 10ns. (TA = +25°C, f = 1.0MHz) Symbol CIN COUT(3) TBIAS Temperature Under Bias -55 to +125 o TSTG Storage Temperature -65 to +150 o IOUT DC Output Current 50 Input Low Voltage ____ Capacitance(1) Absolute Maximum Ratings(1) Symbol VIL (2) C Parameter Input Capacitance Output Capacitance Conditions(2) Max. Unit VIN = 3dV 9 pF VOUT = 3dV 10 pF 4847 tbl 07 NOTES: 1. These parameters are determined by device characterization, but are not production tested. 2. 3dV references the interpolated capacitance when the input and output switch from 0V to 3V or from 3V to 0V. 3. COUT also references CI/O. C mA 4847 tbl 06 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VTERM must not exceed Vcc + 10% for more than 25% of the cycle time or 10ns maximum, and is limited to < 20mA for the period of VTERM > Vcc + 10%. DC Electrical Characteristics Over the Operating Temperature Supply Voltage Range (VCC = 5.0V ± 10%) 709199L Symbol Parameter Test Conditions Min. Max. Unit |ILI| Input Leakage Current(1) VCC = 5.5V, VIN = 0V to V CC ___ 5 µA |ILO| Output Leakage Current CE0 = VIH or CE1 = VIL, VOUT = 0V to V CC ___ 5 µA IOL = +4mA ___ 0.4 V 2.4 ___ V VOL VOH Output Low Voltage Output High Voltage IOH = -4mA 4847 tbl 08 NOTE: 1. At Vcc < 2.0V input leakages are undefined. 4 6.42 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(3,6) (VCC = 5V ± 10%) 709199L7 Com'l Only Symbol ICC ISB1 ISB2 ISB3 ISB4 Parameter Test Condition Version 709199L9 Com'l Only 709199L12 Com'l Only Typ.(4) Max. Typ.(4) Max. Typ.(4) Max. Unit mA Dynamic Operating Current (Both Ports Active) CEL and CER= VIL Outputs Disabled f = fMAX(1) COM'L L 275 465 250 400 230 355 IND L ____ ____ ____ ____ ____ ____ Standby Current (Both Ports - TTL Level Inputs) CEL = CER = VIH f = fMAX(1) COM'L L 95 150 80 135 70 110 IND L ____ ____ ____ ____ ____ ____ Standby Current (One Port - TTL Level Inputs) CE"A" = VIL and CE"B" = VIH(3) Active Port Outputs Disabled, f=fMAX(1) COM'L L 200 295 175 275 150 240 IND L ____ ____ ____ ____ ____ ____ Full Standby Current (Both Ports CMOS Level Inputs) Both Ports CER and CEL > VCC - 0.2V VIN > VCC - 0.2V or VIN < 0.2V, f = 0(2) COM'L L 0.5 3 0.5 3 0.5 3 IND L ____ ____ ____ ____ ____ ____ Full Standby Current (One Port CMOS Level Inputs) CE"A" < 0.2V and CE"B" > VCC - 0.2V(5) VIN > VCC - 0.2V or VIN < 0.2V, Active Port Outp uts Disabled, f = fMAX(1) COM'L L 190 290 170 270 140 225 L ____ ____ ____ ____ ____ ____ IND mA mA mA mA 4847 tbl 09 NOTES: 1. At f = f MAX, address and control lines (except Output Enable) are cycling at the maximum frequency clock cycle of 1/tCYC , using "AC TEST CONDITIONS" at input levels of GND to 3V. 2. f = 0 means no address, clock, or control lines change. Applies only to input at CMOS level standby. 3. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 4. Vcc = 5V, TA = 25°C for Typ, and are not production tested. I CC DC(f=0) = 150mA (Typ). 5. CE X = VIL means CE0X = VIL and CE1X = VIH CE X = VIH means CE0X = VIH or CE1X = V IL CE X < 0.2V means CE0X < 0.2V and CE1X > VCC - 0.2V CE X > VCC - 0.2V means CE0X > VCC - 0.2V or CE1X < 0.2V "X" represents "L" for left port or "R" for right port. 6. Industrial temperature: for specific speeds, packages and powers contact your sales office. 6.42 5 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Test Conditions Input Pulse Levels GND to 3.0V Input Rise/Fall Times 3ns Max. Input Timing Reference Levels 1.5V Output Reference Levels 1.5V Output Load Figures 1,2 and 3 4847 tbl 10 5V 5V 893Ω 893Ω DATAOUT DATAOUT 30pF 347Ω 4847 drw 04 4847 drw 05 Figure 1. AC Output Test load. 8 7 Figure 2. Output Test Load (For tCKLZ , tCKHZ, tOLZ, and tOHZ). *Including scope and jig. - 10pF is the I/O capacitance of this device, and 30pF is the AC Test Load Capacitance 6 tCD1, tCD2 (Typical, ns) 5 4 3 2 1 0 -1 5pF* 347Ω 20 40 60 80 100 120 140 160 180 200 Capacitance (pF) 4847 drw 06 Figure 3. Typical Output Derating (Lumped Capacitive Load). 6 6.42 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature Range (Read and Write Cycle Timing)(3,4) (VCC = 5V ± 10%, TA = 0°C to +70°C) 709199L7 Com'l Only Symbol tCYC1 tCYC2 tCH1 Parameter (2) Clock Cycle Time (Flow-Through) (2) Clock Cycle Time (Pipelined) (2) Clock High Time (Flow-Through) (2) Min. Max. 22 ____ 12 ____ 7.5 ____ 709199L9 Com'l Only Min. Max. 25 ____ 15 ____ 12 ____ 709199L12 Com'l Only Min. Max. Unit 30 ____ ns 20 ____ ns 12 ____ ns ns 7.5 ____ 12 ____ 12 ____ tCH2 (2) Clock High Time (Pipelined) 5 ____ 6 ____ 8 ____ ns tCL2 Clock Low Time (Pipelined)(2) 5 ____ 6 ____ 8 ____ ns tR Clock Rise Time ____ 3 ____ 3 ____ 3 ns Clock Fall Time ____ 3 ____ 3 ____ 3 ns 4 ____ 4 ____ 4 ____ ns 0 ____ 1 ____ 1 ____ ns 4 ____ 4 ____ 4 ____ ns 0 ____ 1 ____ 1 ____ ns ns tCL1 tF tSA tHA tSC tHC Clock Low Time (Flow-Through) Address Setup Time Address Hold Time Chip Enable Setup Time Chip Enable Hold Time tSW R/W Setup Time 4 ____ 4 ____ 4 ____ tHW R/W Hold Time 0 ____ 1 ____ 1 ____ ns tSD Input Data Setup Time 4 ____ 4 ____ 4 ____ ns 0 ____ 1 ____ 1 ____ ns 4 ____ 4 ____ 4 ____ ns 0 ____ 1 ____ 1 ____ ns 4 ____ 4 ____ 4 ____ ns 0 ____ 1 ____ 1 ____ ns 4 ____ 4 ____ 4 ____ ns 0 ____ 1 ____ 1 ____ ns ____ 9 ____ 12 ____ 12 ns 2 ____ 2 ____ 2 ____ ns tHD Input Data Hold Time tSAD ADS Setup Time tHAD ADS Hold Time tSCN CNTEN Setup Time tHCN CNTEN Hold Time tSRST CNTRST Setup Time tHRST CNTRST Hold Time tOE tOLZ Output Enable to Data Valid (1) Output Enable to Output Low-Z (1) tOHZ Output Enable to Output High-Z 1 7 1 7 1 7 ns tCD1 Clock to Data Valid (Flow-Through)(2) ____ 18 ____ 20 ____ 25 ns tCD2 Clock to Data Valid (Pipelined)(2) ____ 7.5 ____ 9 ____ 12 ns 2 ____ 2 ____ 2 ____ ns 2 9 2 9 2 9 ns 2 ____ 2 ____ 2 ____ ns Write Port Clock High to Read Data Delay ____ 28 ____ 35 ____ 40 ns Clock-to-Clock Setup Time ____ 10 ____ 15 ____ 15 tDC tCKHZ tCKLZ Data Output Hold After Clock High (1) Clock High to Output High-Z (1) Clock High to Output Low-Z Port-to-Port Delay tCWDD tCCS ns 4847 tbl 11 NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). This parameter is guaranteed by device characterization, but is not production tested. 2. The Pipelined output parameters (tCYC2, tCD2 ) to either the Left or Right ports when FT/PIPE = VIH. Flow-Through parameters (tCYC1, tCD1) apply when FT/PIPE = VIL for that port . 3. All input signals are synchronous with respect to the clock except for the asynchronous Output Enable (OE), FT/PIPER and FT/PIPEL. 4. Industrial temperature: for specific speeds, packages and powers contact your sales office. 6.42 7 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Read Cycle for Flow-Through Output (FT/PIPE"X" = VIL)(3,6) tCYC1 tCH1 tCL1 CLK CE0 tSC tSC tHC (4) CE1 R/W tSW tHW tSA tHA (5) ADDRESS An An + 1 An + 2 An + 3 tDC tCD1 tCKHZ (1) Qn DATAOUT Qn + 1 tCKLZ (1) OE tHC tOHZ Qn + 2 (1) tOLZ tDC (1) (2) tOE 4847 drw 07 Timing Waveform of Read Cycle for Pipelined Operation (FT/PIPE"X" = VIH)(3,6) tCYC2 tCH2 tCL2 CLK CE0 tSC tSC tHC tHC (4) CE1 R/W (5) ADDRESS tSW tHW tSA tHA An An + 1 (1 Latency) An + 2 tDC tCD2 DATAOUT Qn tCKLZ An + 3 (1) Qn + 1 tOHZ (1) Qn + 2 tOLZ (6) (1) (2) OE tOE 4847 drw 08 NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). 2. OE is asynchronously controlled; all other inputs are synchronous to the rising clock edge. 3. ADS = VIL, CNTEN and CNTRST = VIH. 4. The output is disabled (High-Impedance state) by CE0 = V IH or CE1 = V IL following the next rising edge of the clock. Refer to Truth Table 1. 5. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 6. "X" here denotes Left or Right port. The diagram is with respect to that port. 8 6.42 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of a Bank Select Pipelined Read(1,2) tCH2 tCYC2 tCL2 CLK tSA CE0(B1) tHA A0 ADDRESS(B1) tSC tHC tSC tHC tCD2 DATAOUT(B1) A0 tSC tCD2 Q3 tCKLZ (3) tCKHZ (3) tHA A6 A5 A4 A3 A2 A1 tSC CE0(B2) tCKHZ Q1 tDC tDC ADDRESS(B2) (3) tCD2 Q0 tSA A6 A5 A4 A3 A2 A1 tHC tHC tCKHZ (3) tCD2 DATAOUT(B2) tCKLZ (3) tCD2 Q2 tCKLZ Q4 (3) 4847 drw 09 Timing Waveform of Write with Port-to-Port Flow-Through Read(4,5,7) CLK "A" tSW tHW R/W "A" tSA ADDRESS "A" NO MATCH MATCH tSD DATAIN "A" tHA tHD VALID tCCS (6) CLK "B" tCD1 R/W "B" ADDRESS "B" tSW tHW tSA tHA NO MATCH MATCH tCWDD (6) tCD1 DATAOUT "B" VALID VALID tDC tDC 4847 drw 10 NOTES: 1. B1 Represents Bank #1; B2 Represents Bank #2. Each Bank consists of one IDT709199 for this waveform, and are setup for depth expansion in this example. ADDRESS (B1) = ADDRESS(B2) in this situation. 2. OE and ADS = VIL; CE1(B1), CE 1(B2), R/W, CNTEN, and CNTRST = VIH. 3. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). 4. CE 0 and ADS = VIL; CE1, CNTEN, and CNTRST = VIH. 5. OE = VIL for the Right Port, which is being read from. OE = VIH for the Left Port, which is being written to. 6. If tCCS < maximum specified, then data from right port READ is not valid until the maximum specified for tCWDD . If tCCS > maximum specified, then data from right port READ is not valid until tCCS + tCD1. t CWDD does not apply in this case. 7. All timing is the same for both Left and Right ports. Port "A" may be either Left or Right port. Port "B" is the opposite from Port "A". 6.42 9 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Pipelined Read-to-Write-to-Read (OE = VIL)(3) tCYC2 tCH2 tCL2 CLK CE0 tSC tHC CE1 tSW tHW R/W tSW tHW (4) An tSA tHA ADDRESS An +1 An + 2 An + 3 An + 2 An + 4 tSD tHD DATAIN Dn + 2 tCD2 (2) tCKHZ (1) (1) tCKLZ tCD2 Qn + 3 Qn DATAOUT READ NOP (5) WRITE READ 4847 drw 11 Timing Waveforn of Pipelined Read-to-Write-to-Read (OE Controlled)(3) tCH2 tCYC2 tCL2 CLK CE0 tSC tHC CE1 tSW tHW R/W (4) ADDRESS tSW tHW An tSA tHA An +1 An + 2 An + 3 An + 4 An + 5 tSD tHD DATAIN Dn + 2 tCD2 (2) Dn + 3 tCKLZ(1) tCD2 Qn DATAOUT Qn + 4 (1) tOHZ OE READ WRITE READ 4847 drw 12 NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). 2. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 3. CE0 and ADS = VIL; CE 1, CNTEN, and CNTRST = VIH. "NOP" is "No Operation". 4. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 5. "NOP" is "No Operation." Data in memory at the selected address may be corrupted and should be re-written to guarantee data integrity. 10 6.42 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Flow-Through Read-to-Write-to-Read (OE = VIL)(3) tCH1 tCYC1 tCL1 CLK CE0 tSC tHC CE1 tSW tHW R/W tSW tHW (4) ADDRESS tSA An tHA An +1 An + 2 An + 4 An + 3 An + 2 tSD tHD DATAIN Dn + 2 tCD1 (2) tCD1 Qn DATAOUT tCD1 tCD1 Qn + 3 Qn + 1 tDC tCKHZ (5) NOP READ (1) tCKLZ WRITE (1) tDC READ 4847 drw 13 Timing Waveform of Flow-Through Read-to-Write-to-Read (OE Controlled)(3) tCYC1 tCH1 tCL1 CLK CE0 tSC tHC CE1 tSW tHW R/W tSW tHW (4) ADDRESS tSA An tHA An +1 An + 2 DATAIN Dn + 3 Dn + 2 (2) DATAOUT An + 3 An + 4 An + 5 tSD tHD tDC tCD1 Qn tOE tCD1 (1) tCKLZ tOHZ (1) tCD1 Qn + 4 tDC OE READ WRITE READ 4847 drw 14 NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with the Output Test Load (Figure 2). 2. Output state (High, Low, or High-impedance is determined by the previous cycle control signals. 3. CE 0 and ADS = VIL; CE 1, CNTEN, and CNTRST = V IH. "NOP" is "No Operation". 4. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 5. "NOP" is "No Operation." Data in memory at the selected address may be corrupted and should be re-written to guarantee data integrity. 6.42 11 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Pipelined Read with Address Counter Advance(1) tCH2 tCYC2 tCL2 CLK tSA ADDRESS tHA An tSAD tHAD ADS tSAD tHAD CNTEN tSCN tHCN tCD2 DATAOUT Qx - 1(2) Qn + 2(2) Qn + 1 Qn Qx Qn + 3 tDC READ EXTERNAL ADDRESS READ WITH COUNTER COUNTER HOLD READ WITH COUNTER 4847 drw 15 Timing Waveform of Flow-Through Read with Address Counter Advance(1) tCH1 tCYC1 tCL1 CLK tSA ADDRESS tHA An tSAD tHAD ADS tSAD tHAD tSCN tHCN CNTEN tCD1 DATAOUT Qx(2) Qn Qn + 1 Qn + 2 Qn + 3(2) Qn + 4 tDC READ EXTERNAL ADDRESS READ WITH COUNTER COUNTER HOLD READ WITH COUNTER 4847 drw 16 NOTES: 1. CE0 and OE = VIL; CE 1, R/W, and CNTRST = VIH. 2. If there is no address change via ADS = VIL (loading a new address) or CNTEN = VIL (advancing the address), i.e. ADS = VIH and CNTEN = VIH, then the data output remains constant for subsequent clocks. 12 6.42 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Write with Address Counter Advance (Flow-Through or Pipelined Outputs)(1) tCH2 tCYC2 tCL2 CLK tSA tHA An ADDRESS INTERNAL(3) ADDRESS An(7) An + 2 An + 1 An + 4 An + 3 tSAD tHAD ADS CNTEN tSD tHD Dn + 1 Dn DATAIN WRITE EXTERNAL ADDRESS Dn + 1 Dn + 4 Dn + 3 Dn + 2 WRITE WRITE WITH COUNTER COUNTER HOLD WRITE WITH COUNTER 4847 drw 17 Timing Waveform of Counter Reset (Pipelined Outputs)(2) tCH2 tCYC2 tCL2 CLK tSA tHA ADDRESS(4) INTERNAL(3) ADDRESS An Ax (6) 0 1 An + 2 An + 1 An + 1 An tSW tHW R/W ADS CNTEN tSRST tHRST CNTRST tSD tHD D0 DATAIN Qn Q1 Q0 DATAOUT(5) . COUNTER(6) RESET WRITE ADDRESS 0 READ ADDRESS 0 READ ADDRESS 1 READ ADDRESS n READ ADDRESS n+1 4847 drw 18 NOTES: 1. CE0 and R/W = VIL; CE1 and CNTRST = VIH. 2. CE0 = VIL; CE1 = VIH. 3. The "Internal Address" is equal to the "External Address" when ADS = VIL and equals the counter output when ADS = VIH. 4. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 5. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 6. No dead cycle exists during counter reset. A READ or WRITE cycle may be coincidental with the counter reset cycle. 7. CNTEN = VIL advances Internal Address from ‘An’ to ‘An +1’. The transition shown indicates the time required for the counter to advance. The ‘An +1’ Address is written to during this cycle. 6.42 13 IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges A Functional Description Depth and Width Expansion The IDT709199 provides a true synchronous Dual-Port Static RAM interface. Registered inputs provide minimal set-up and hold times on address, data, and all critical control inputs. All internal registers are clocked on the rising edge of the clock signal, however, the self-timed internal write pulse is independent of the LOW to HIGH transition of the clock signal. An asynchronous output enable is provided to ease asynchronous bus interfacing. Counter enable inputs are also provided to stall the operation of the address counters for fast interleaved memory applications. CE0 = VIH or CE1 = VIL for one clock cycle will power down the internal circuitry to reduce static power consumption. Multiple chip enables allow easier banking of multiple IDT709199's for depth expansion configurations. When the Pipelined output mode is enabled, two cycles are required with CE0 = VIL and CE1 = VIH to reactivate the outputs. The IDT709199 features dual chip enables (refer to Truth Table I) in order to facilitate rapid and simple depth expansion with no requirements for external logic. Figure 4 illustrates how to control the various chip enables in order to expand two devices in depth. The 709199 can also be used in applications requiring expanded width, as indicated in Figure 4. Since the banks are allocated at the discretion of the user, the external controller can be set up to drive the input signals for the various devices as required to allow for 18-bit or wider applications. A17 CE0 IDT709199 CE1 CE1 CE1 VCC IDT709199 VCC CE1 CE0 CE0 Control Inputs CE0 Control Inputs Control Inputs IDT709199 IDT709199 Control Inputs 4847 drw 19 Figure 4. Depth and Width Expansion with IDT709199 14 6.42 CNTRST CLK ADS CNTEN R/W OE IDT709199L High-Speed 128K x 9 Synchronous Pipelined Dual-Port Static RAM Industrial and Commercial Temperature Ranges Ordering Information IDT XXXXX A 99 A A Device Type Power Speed Package Process/ Temperature Range Blank I(1) Commercial (0°C to +70°C) Industrial (-40°C to +85°C) PF 100-pin TQFP (PN100-1) 7 9 12 Commercial Only Commercial Only Commercial Only L Low Power Speed in nanoseconds 709199 1152K (128K x 9-Bit) Synchronous Dual-Port RAM 4847 drw 20 NOTE: 1. Industrial temperature range is available. For specific speeds, packages and powers contact your sales office. Datasheet Document History 9/30/99: 11/10/99: 12/22/99: 1/5/01: Initial Public Release Replaced IDT logo Page 1 Added missing diamond Page 3 Changed information in Truth Table II Page 4 Increased storage temperature parameter Clarified TA parameter Page 5 DC Electrical parameters–changed wording from "open" to "disabled" Put overbar on CE in notes Changed ±200mV to 0mV in notes Deleted Preliminary CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 6.42 15 for Tech Support: 831-754-4613 [email protected]