ADVANCE INFORMATION MX27C8000A 8M-BIT [1M x8] CMOS EPROM FEATURES • • • • • • • Operating current: 60mA • Standby current: 100uA • Package type: 1M x 8 organization Single +5V power supply +12.5V programming voltage Fast access time: 90/100/120/150 ns Totally static operation Completely TTL compatible - 32 pin plastic DIP 32 pin PLCC 32 pin SOP 32 pin TSOP GENERAL DESCRIPTION The MX27C8000A is a 5V only, 8M-bit, ultraviolet Erasable Programmable Read Only Memory. It is organized as 1M words by 8 bits per word, operates from a single +5 volt supply, has a static standby mode, and features fast single address location programming. All programming signals are TTL levels, requiring a single pulse. For programming outside from the system, existing EPROM programmers may be used. The MX27C8000A supports a intelligent fast programming algorithm which can result in programming time of less than two minutes. This EPROM is packaged in industry standard 32 pin dual-in-line packages, 32 lead PLCC, 32 lead SOP and 32 lead TSOP packages. A7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 P/N: PM00764 VCC 1 32 A17 A19 4 30 29 A14 A6 A13 A5 A8 A9 A4 A3 9 MX27C8000A 25 A11 A2 OE/VPP A1 A10 CE A0 21 20 Q5 Q4 Q3 17 Q7 Q6 13 14 GND Q0 PIN DESCRIPTION 32 TSOP A11 A9 A8 A13 A14 A17 A18 VCC A19 A16 A15 A12 A7 A6 A5 A4 5 A16 A12 VCC A18 A17 A14 A13 A8 A9 A11 OE/VPP A10 CE Q7 Q6 Q5 Q4 Q3 Q2 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 Q1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 MX27C8000A A19 A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 Q0 Q1 Q2 GND A15 32 PLCC 32 PDIP/SOP A18 PIN CONFIGURATIONS MX27C8000A 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 SYMBOL PIN NAME OE/VPP A10 CE Q7 Q6 Q5 Q4 Q3 GND Q2 Q1 Q0 A0 A1 A2 A3 A0~A19 Address Input Q0~Q7 Data Input/Output CE Chip Enable Input OE/VPP Output Enable Input/Program Supply Voltage 1 VCC Power Supply Pin (+5V) GND Ground Pin REV. 1.2, JUL. 19, 2001 MX27C8000A BLOCK DIAGRAM CE OE/VPP . CONTROL OUTPUT LOGIC BUFFERS Y-DECODER A0~A19 . . . . . Programming of multiple MX27C8000As in parallel with different data is also easily accomplished by using the Program Inhibit Mode. Except for CE and OE, all like inputs of the parallel MX27C8000A may be common. A TTL low-level program pulse applied to an MX27C8000A CE input with OE/VPP = 12.5 ± 0.5 Vwill program that MX27C8000A. A high-level CE input inhibits the other MX27C8000As from being programmed. Q0~Q7 Y-SELECT . . . . ADDRESS INPUTS PROGRAM INHIBIT MODE . X-DECODER . . . . . 8M BIT CELL MAXTRIX PROGRAM VERIFY MODE VCC Verification should be performed on the programmed bits to determine that they were correctly programmed. The verification should be performed with OE /VPPand CE, at VIL, data should be verified tDV after the falling edge of CE. GND FUNCTIONAL DESCRIPTION THE PROGRAMMING OF THE MX27C8000A AUTO IDENTIFY MODE When the MX27C8000A is delivered, or it is erased, the chip has all 8M bits in the "ONE" or HIGH state. "ZEROs" are loaded into the MX27C8000A through the procedure of programming. The auto identify mode allows the reading out of a binary code from an EPROM that will identify its manufacturer and device type. This mode is intended for use by programming equipment for the purpose of automatically matching the device to be programmed with its corresponding programming algorithm. This mode is functional in the 25°C ± 5°C ambient temperature range that is required when programming the MX27C8000A. For programming, the data to be programmed is applied with 8 bits in parallel to the data pins. Vcc must be applied simultaneously or before Vpp, and removed simultaneously or after Vpp. When programming an MXIC EPROM, a 0.1uF capacitor is required across Vpp and ground to suppress spurious voltage transients which may damage the device. To activate this mode, the programming equipment must force 12.0 ± 0.5 V on address line A9 of the device. Two identifier bytes may then be sequenced from the device outputs by toggling address line A0 from VIL to VIH. All other address lines must be held at VIL during auto identify mode. FAST PROGRAMMING Byte 0 ( A0 = VIL) represents the manufacturer code, and byte 1 (A0 = VIH), the device identifier code. For the MX27C8000A, these two identifier bytes are given in the Mode Select Table. All identifiers for manufacturer and device codes will possess odd parity, with the MSB (Q7) defined as the parity bit. The device is set up in the fast programming mode when the programming voltage OE/VPP = 12.75V is applied, with VCC = 6.25 V (Algorithm is shown in Figure 1). The programming is achieved by applying a single TTL low level 50us pulse to the CE input after addresses and data line are stable. If the data is not verified, an additional pulse is applied for a maximum of 25 pulses. This process is repeated while sequencing through each address of the device. When the programming mode is completed, the data in all address is verified at VCC = 5V ± 10%. P/N: PM00764 READ MODE The MX27C8000A has two control functions, both of which must be logically satisfied in order to obtain data at the outputs. Chip Enable (CE) is the power control and 2 REV.1.2, JUL. 19, 2001 MX27C8000A 2. Assurance that output bus contention will not occur. should be used for device selection. Output Enable (OE) is the output control and should be used to gate data to the output pins, independent of device selection. Assuming that addresses are stable, address access time (tACC) is equal to the delay from CE to output (tCE). Data is available at the outputs tOE after the falling edge of OE's, assuming that CE has been LOW and addresses have been stable for at least tACC - tOE. It is recommended that CE be decoded and used as the primary device-selecting function, while OE be made a common connection to all devices in the array and connected to the READ line from the system control bus. This assures that all deselected memory devices are in their low-power standby mode and that the output pins are only active when data is desired from a particular memory device. STANDBY MODE The MX27C8000A has a CMOS standby mode which reduces the maximum VCC current to 100 uA. It is placed in CMOS standby when CE is at VCC ± 0.3 V. The MX27C8000A also has a TTL-standby mode which reduces the maximum VCC current to 1.5 mA. It is placed in TTL-standby when CE is at VIH. When in standby mode, the outputs are in a high-impedance state, independent of the OE input. SYSTEM CONSIDERATIONS During the switch between active and standby conditions, transient current peaks are produced on the rising and falling edges of Chip Enable. The magnitude of these transient current peaks is dependent on the output capacitance loading of the device. At a minimum, a 0.1 uF ceramic capacitor (high frequency, low inherent inductance) should be used on each device between VCC and GND to minimize transient effects. In addition, to overcome the voltage drop caused by the inductive effects of the printed circuit board traces on EPROM arrays, a 4.7 uF bulk electrolytic capacitor should be used between VCC and GND for each eight devices. The location of the capacitor should be close to where the power supply is connected to the array. TWO-LINE OUTPUT CONTROL FUNCTION To accommodate multiple memory connections, a twoline control function is provided to allow for: 1. Low memory power dissipation, MODE SELECT TABLE PINS MODE CE OE/VPP A0 A9 OUTPUTS Read VIL VIL X X DOUT Output Disable VIL VIH X X High Z Standby (TTL) VIH X X X High Z Standby (CMOS) VCC±0.3V X X X High Z Program VIL VPP X X DIN Program Verify VIL VIL X X DOUT Program Inhibit VIH VPP X X High Z Manufacturer Code(3) VIL VIL VIL VH C2H Device Code(3) VIL VIL VIH VH 02H NOTES: 1. VH = 12.0 V ± 0.5 V 2. X = Either VIH or VIL 3. A1 - A8 = A10 - A19 = VIL (For auto select) 4. See DC Programming Characteristics for VPP voltage during programming P/N: PM00764 3 REV.1.2, JUL. 19, 2001 MX27C8000A FIigure 1. FAST PROGRAMMING FLOW CHART START ADDRESS = FIRST LOCATION VCC = 6.25V OE/VPP = 12.75V PROGRAM ONE 50 us PULSE NO INCREMENT ADDRESS LAST ADDRESS ? YES ADDRESS = FIRST LOCATION X=0 INCREMENT ADDRESS NO LAST ADDRESS ? PASS VERIFY BYTE FAIL INCREMENT X YES NO PROGRAM ONE 50us PULSE YES VCC = 5.25V OE/VPP = VIL COMPARE ALL BYTES TO ORIGINAL DATA X = 25 ? FAIL DEVICE FAILED PASS DEVICE PASSED P/N: PM00764 4 REV.1.2, JUL. 19, 2001 MX27C8000A SWITCHING TEST CIRCUITS 1.8K ohm DEVICE +5V UNDER TEST DIODES = IN3064 CL OR EQUIVALENT 6.2K ohm CL = 100 pF including jig capacitance SWITCHING TEST WAVEFORMS 2.0V 2.0V TEST POINTS AC driving levels 0.8V 0.8V OUTPUT INPUT AC TESTING: AC driving levels are 2.4V/0.4V for commercial grade. Input pulse rise and fall times are < 10ns. P/N: PM00764 5 REV.1.2, JUL. 19, 2001 MX27C8000A ABSOLUTE MAXIMUM RATINGS RATING VALUE Ambient Operating Temperature -40oC to 85oC Storage Temperature -65oC to 125oC Applied Input Voltage -0.5V to 7.0V Applied Output Voltage -0.5V to VCC + 0.5V VCC to Ground Potential -0.5V to 7.0V A9 & VPP -0.5V to 13.5V NOTICE: Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended period may affect reliability. NOTICE: Specifications contained within the following tables are subject to change. DC/AC OPERATING CONDITION FOR READ OPERATION MX27C8000A Operating Temperature Industrial -90 -10 -12 -15 -40°C to 85°C -40°C to 85°C -40°C to 85°C -40°C to 85°C 5V ± 10% 5V ± 10% 5V ± 10% 5V ± 10% Vcc Power Supply DC CHARACTERISTICS SYMBOL PARAMETER MIN. VOH Output High Voltage 2.4 VOL Output Low Voltage VIH Input High Voltage VIL MAX. UNIT CONDITIONS V IOH = -0.4mA 0.4 V IOL = 2.1mA 2.0 VCC + 0.5 V Input Low Voltage -0.3 0.8 V ILI Input Leakage Current -10 10 uA VIN = 0 to 5.5V ILO Output Leakage Current -10 10 uA VOUT = 0 to 5.5V ICC3 VCC Power-Down Current 100 uA CE = VCC ± 0.3V ICC2 VCC Standby Current 1.5 mA CE = VIH ICC1 VCC Active Current 60 mA CE = VIL, f=5MHz, Iout = 0mA IPP VPP Supply Current Read 10 uA CE = OE = VIL, VPP = 5.5V CAPACITANCE TA = 25oC, f = 1.0 MHz (Sampled only) SYMBOL PARAMETER TYP. MAX. UNIT CONDITIONS CIN Input Capacitance 8 12 pF VIN = 0V COUT Output Capacitance 8 12 pF VOUT = 0V CVPP VPP Capacitance 18 25 pF VPP = 0V P/N: PM00764 6 REV.1.2, JUL. 19, 2001 MX27C8000A AC CHARACTERISTICS 27C8000A-90 27C8000A-10 27C8000A-12 27C8000A-15 Symbol PARAMETER MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. Unit Conditions tACC Address to Output Delay 90 100 120 150 ns CE=OE=VIL tCE Chip Enable to Output Delay 90 100 120 150 ns OE=VIL tOE Output Enable to Output Delay 40 40 50 65 ns CE=VIL tDF OE High to Output Float, 50 ns 0 30 0 30 0 35 0 0 0 or CE High to Output Float tOH Output Hold from Address,CE or 0 0 ns OE which ever occurred first DC PROGRAMMING CHARACTERISTICS TA = 25oC ± 5oC SYMBOL PARAMETER MIN. VOH Output High Voltage 2.4 VOL Output Low Voltage VIH Input High Voltage VIL MAX. UNIT CONDITIONS V IOH = -0.40mA 0.4 V IOL = 2.1mA 2.0 VCC + 0.5 V Input Low Voltage -0.3 0.8 V ILI Input Leakage Current -10 10 uA VH A9 Auto Select Voltage 11.5 12.5 V ICC3 VCC Supply Current (Program & Verify) 50 mA IPP2 VPP Supply Current(Program) 30 mA VCC1 Fast Programming Supply Voltage 6.00 6.50 V VPP1 Fast Programming Voltage 12.5 13.0 V VIN = 0 to 5.5V CE = VIL AC PROGRAMMING CHARACTERISTICS TA = 25oC ± 5oC SYMBOL PARAMETER MIN. tAS Address Setup Time 2.0 us tDS Data Setup Time 2.0 us tAH Address Hold Time 0 us tDH Data Hold Time 2.0 us tDFP Chip Enable to Output Float Delay 0 tVPS VPP Setup Time 2.0 tPW CE Program Pulse Width 10 tVCS VCC Setup Time 2.0 tDV Data Valid from CE tOEH OE/VPP Hold Time 2.0 us tVR OE/VPP Recovery Time 2.0 us P/N: PM00764 TYP. MAX. 130 ns us 50 us us 150 7 UNIT ns REV.1.2, JUL. 19, 2001 MX27C8000A WAVEFORMS READ CYCLE ADDRESS INPUTS DATA ADDRESS tACC CE tCE OE tDF DATA OUT VALID DATA tOE tOH FAST PROGRAMMING ALGORITHM WAVEFORMS PROGRAM PROGRAM VERIFY VIH Addresses VIL Hi-z tAS DATA OUT VALID DATA tDV tDS tDH tDFP VPP1 OE/VPP VIL tVPS tVR tPW VIH CE tVPS tAH VIL tVCS VCC1 VCC P/N: PM00764 VCC 8 REV.1.2, JUL. 19, 2001 MX27C8000A ORDERING INFORMATION PLASTIC PACKAGE PART NO. ACCESS TIME OPERATING STANDBY (ns) Current MAX.(mA) Current MAX.(uA) MX27C8000APC-90 90 30 100 0°C to 70°C 32 Pin DIP MX27C8000AQC-90 90 30 100 0°C to 70°C 32 Pin PLCC MX27C8000AMC-90 90 30 100 0°C to 70°C 32 Pin SOP MX27C8000ATC-90 90 30 100 0°C to 70°C 32 Pin TSOP MX27C8000APC-10 100 30 100 0°C to 70°C 32 Pin DIP MX27C8000AQC-10 100 30 100 0°C to 70°C 32 Pin PLCC MX27C8000AMC-10 100 30 100 0°C to 70°C 32 Pin SOP MX27C8000ATC-10 100 30 100 0°C to 70°C 32 Pin TSOP MX27C8000APC-12 120 30 100 0°C to 70°C 32 Pin DIP MX27C8000AQC-12 120 30 100 0°C to 70°C 32 Pin PLCC MX27C8000AMC-12 120 30 100 0°C to 70°C 32 Pin SOP MX27C8000ATC-12 120 30 100 0°C to 70°C 32 Pin TSOP MX27C8000APC-15 150 30 100 0°C to 70°C 32 Pin DIP MX27C8000AQC-15 150 30 100 0°C to 70°C 32 Pin PLCC MX27C8000AMC-15 150 30 100 0°C to 70°C 32 Pin SOP MX27C8000ATC-15 150 30 100 0°C to 70°C 32 Pin TSOP MX27C8000API-90 90 30 100 -40°C to 85°C 32 Pin DIP MX27C8000AQI-90 90 30 100 -40°C to 85°C 32 Pin PLCC MX27C8000AMI-90 90 30 100 -40°C to 85°C 32 Pin SOP MX27C8000ATI-90 90 30 100 -40°C to 85°C 32 Pin TSOP MX27C8000API-10 100 30 100 -40°C to 85°C 32 Pin DIP MX27C8000AQI-10 100 30 100 -40°C to 85°C 32 Pin PLCC MX27C8000AMI-10 100 30 100 -40°C to 85°C 32 Pin SOP MX27C8000ATI-10 100 30 100 -40°C to 85°C 32 Pin TSOP MX27C8000API-12 120 30 100 -40°C to 85°C 32 Pin DIP MX27C8000AQI-12 120 30 100 -40°C to 85°C 32 Pin PLCC MX27C8000AMI-12 120 30 100 -40°C to 85°C 32 Pin SOP MX27C8000ATI-12 120 30 100 -40°C to 85°C 32 Pin TSOP MX27C8000API-15 150 30 100 -40°C to 85°C 32 Pin DIP MX27C8000AQI-15 150 30 100 -40°C to 85°C 32 Pin PLCC MX27C8000AMI-15 150 30 100 -40°C to 85°C 32 Pin SOP MX27C8000ATI-15 150 30 100 -40°C to 85°C 32 Pin TSOP P/N: PM00764 9 OPERATING PACKAGE TEMPERATURE REV.1.2, JUL. 19, 2001 MX27C8000A PACKAGE INFORMATION 32-PIN PLASTIC DIP(600 mil) P/N: PM00764 10 REV.1.2, JUL. 19, 2001 MX27C8000A 32-PIN PLASTIC LEADED CHIP CARRIER (PLCC) P/N: PM00764 11 REV.1.2, JUL. 19, 2001 MX27C8000A 32-PIN PLASTIC SOP (450 mil) P/N: PM00764 12 REV.1.2, JUL. 19, 2001 MX27C8000A 32-PIN PLASTIC TSOP P/N: PM00764 13 REV.1.2, JUL. 19, 2001 MX27C8000A REVISION HISTORY Revision No. Description 1.1 To change data sheet title to Advance Information To added access time 90ns and 32SOP/TSOP type package To changed ID Code from 35H to 02H 1.2 To modify Package Information P/N: PM00764 14 Page P1 P1,6,7,9,11 P6 P10~13 Date MAR/15/2001 JUL/19/2001 REV.1.2, JUL. 19, 2001 MX27C8000A MACRONIX INTERNATIONAL CO., LTD. HEADQUARTERS: TEL:+886-3-578-6688 FAX:+886-3-563-2888 EUROPE OFFICE: TEL:+32-2-456-8020 FAX:+32-2-456-8021 JAPAN OFFICE: TEL:+81-44-246-9100 FAX:+81-44-246-9105 SINGAPORE OFFICE: TEL:+65-348-8385 FAX:+65-348-8096 TAIPEI OFFICE: TEL:+886-2-2509-3300 FAX:+886-2-2509-2200 MACRONIX AMERICA, INC. TEL:+1-408-453-8088 FAX:+1-408-453-8488 CHICAGO OFFICE: TEL:+1-847-963-1900 FAX:+1-847-963-1909 http : //www.macronix.com MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 15