NSC LM78L62ACZ 3-terminal positive regulator Datasheet

LM78LXX Series
3-Terminal Positive Regulators
General Description
The LM78LXX series of three terminal positive regulators is
available with several fixed output voltages making them
useful in a wide range of applications. When used as a zener
diode/resistor combination replacement, the LM78LXX usually results in an effective output impedance improvement of
two orders of magnitude, and lower quiescent current. These
regulators can provide local on card regulation, eliminating
the distribution problems associated with single point regulation. The voltages available allow the LM78LXX to be used in
logic systems, instrumentation, HiFi, and other solid state
electronic equipment.
The LM78LXX is available in the plastic TO-92 (Z) package,
the plastic SO-8 (M) package and a chip sized package
(8-Bump micro SMD) using National’s micro SMD package
technology. With adequate heat sinking the regulator can deliver 100 mA output current. Current limiting is included to
limit the peak output current to a safe value. Safe area pro-
tection for the output transistors is provided to limit internal
power dissipation. If internal power dissipation becomes too
high for the heat sinking provided, the thermal shutdown circuit takes over preventing the IC from overheating.
Features
n LM78L05 in micro SMD package
n Output voltage tolerances of ± 5% over the temperature
range
n Output current of 100 mA
n Internal thermal overload protection
n Output transistor safe area protection
n Internal short circuit current limit
n Available in plastic TO-92 and plastic SO-8 low profile
packages
n No external components
n Output voltages of 5.0V, 6.2V, 8.2V, 9.0V, 12V, 15V
Connection Diagrams
SO-8 Plastic (M)
(Narrow Body)
(TO-92)
Plastic Package (Z)
DS007744-3
DS007744-2
Bottom View
Top View
8-Bump micro SMD
micro SMD Marking Orientation
DS007744-24
Top View
(Bump Side Down)
DS007744-33
Top View
© 2000 National Semiconductor Corporation
DS007744
www.national.com
LM78LXX Series 3-Terminal Positive Regulators
January 2000
LM78LXX Series
Absolute Maximum Ratings (Note 1)
Operating Junction Temperature
SO-8
micro SMD
Soldering Information
Infrared or Convection (20 sec.)
Wave Soldering (10 sec.)
ESD Susceptibility (Note 2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Power Dissipation (Note 5)
Input Voltage
Storage Temperature
Internally Limited
35V
−65˚C to +150˚C
0˚C to 125˚C
−40˚C to 85˚C
235˚C
260˚C (lead time)
1kV
LM78LXX Electrical Characteristics
Limits in standard typeface are for TJ = 25˚C, Bold typeface applies over 0˚C to 125˚C for SO-8 package and −40˚C to 85˚C for micro SMD package. Limits are guaranteed by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods. Unless otherwise specified: IO
= 40 mA, CI = 0.33 µF, CO = 0.1 µF.
LM78L05
Unless otherwise specified, VIN = 10V
Symbol
VO
∆VO
∆VO
Parameter
Line Regulation
Load Regulation
IQ
Quiescent Current
∆IQ
Quiescent Current Change
Vn
Conditions
Output Voltage
Output Noise Voltage
Ripple Rejection
Min
Typ
Max
4.8
5
5.2
7V ≤ VIN ≤ 20V
1 mA ≤ IO ≤ 40 mA
(Note 3)
4.75
5.25
1 mA ≤ IO ≤ 70 mA
(Note 3)
4.75
5.25
7V ≤ VIN ≤ 20V
18
75
8V ≤ VIN ≤ 20V
10
54
1 mA ≤ IO ≤ 100 mA
20
60
1 mA ≤ IO ≤ 40 mA
5
30
3
1.0
1 mA ≤ IO ≤ 40 mA
f = 10 Hz to 100 kHz
(Note 4)
f = 120 Hz
8V ≤ VIN ≤ 16V
0.1
Peak Output Current
IPK
Average Output Voltage Tempco
VIN (Min)
Minimum Value of Input Voltage
Required to Maintain Line Regulation
θJA
Thermal Resistance
(8-Bump micro SMD)
IO = 5 mA
V
mV
5
8V ≤ VIN ≤ 20V
47
Units
mA
40
µV
62
dB
140
mA
−0.65
mV/˚C
6.7
7
230.9
V
˚C/W
LM78L62AC
Unless otherwise specified, VIN = 12V
Symbol
VO
∆VO
∆VO
www.national.com
Parameter
Conditions
Output Voltage
Line Regulation
Load Regulation
Min
Typ
Max
5.95
6.2
6.45
8.5V ≤ VIN ≤ 20V
1 mA ≤ IO ≤ 40 mA
(Note 3)
5.9
6.5
1 mA ≤ IO ≤ 70 mA
(Note 3)
5.9
6.5
8.5V ≤ VIN ≤ 20V
65
175
9V ≤ VIN ≤ 20V
55
125
1 mA ≤ IO ≤ 100 mA
13
80
1 mA ≤ IO ≤ 40 mA
6
40
2
Units
V
mV
(Continued)
Unless otherwise specified, VIN = 12V
Symbol
Parameter
IQ
Quiescent Current
∆IQ
Quiescent Current Change
Vn
Output Noise Voltage
Ripple Rejection
Conditions
Min
Average Output Voltage Tempco
VIN (Min)
Max
2
5.5
8V ≤ VIN ≤ 20V
1.5
1 mA ≤ IO ≤ 40 mA
f = 10 Hz to 100 kHz
(Note 4)
f = 120 Hz
10V ≤ VIN ≤ 20V
0.1
40
Peak Output Current
IPK
Typ
IO = 5 mA
Minimum Value of Input Voltage
Required to Maintain Line Regulation
Units
mA
50
µV
46
dB
140
mA
−0.75
mV/˚C
7.9
V
LM78L82AC
Unless otherwise specified, VIN = 14V
Symbol
VO
Parameter
Conditions
Output Voltage
Min
Typ
Max
7.87
8.2
8.53
11V ≤ VIN ≤ 23V
1 mA ≤ IO ≤ 40 mA
(Note 3)
7.8
8.6
1 mA ≤ IO ≤ 70 mA
(Note 3)
7.8
8.6
∆VO
Line Regulation
11V ≤ VIN ≤ 23V
80
175
12V ≤ VIN ≤ 23V
70
125
∆VO
Load Regulation
1 mA ≤ IO ≤ 100 mA
15
80
IQ
Quiescent Current
∆IQ
Quiescent Current Change
1 mA ≤ IO ≤ 40 mA
Vn
Output Noise Voltage
Ripple Rejection
Average Output Voltage Tempco
VIN (Min)
40
5.5
12V ≤ VIN ≤ 23V
1.5
1 mA ≤ IO ≤ 40 mA
f = 10 Hz to 100 kHz
(Note 4)
f = 120 Hz
12V ≤ VIN ≤ 22V
0.1
39
Peak Output Current
IPK
8
2
IO = 5 mA
Minimum Value of Input Voltage
Required to Maintain Line Regulation
Units
V
mV
mA
60
µV
45
dB
140
mA
−0.8
mV/˚C
9.9
V
LM78L09AC
Unless otherwise specified, VIN = 15V
Symbol
VO
Parameter
Conditions
Output Voltage
Min
Typ
Max
8.64
9.0
9.36
11.5V ≤ VIN ≤ 24V
1 mA ≤ IO ≤ 40 mA
(Note 3)
8.55
9.45
1 mA ≤ IO ≤ 70 mA
(Note 3)
8.55
9.45
3
Units
V
www.national.com
LM78LXX Series
LM78L62AC
LM78LXX Series
LM78L09AC
(Continued)
Unless otherwise specified, VIN = 15V
Symbol
∆VO
Parameter
Line Regulation
∆VO
Load Regulation
IQ
Quiescent Current
∆IQ
Quiescent Current Change
Vn
Typ
Max
11.5V ≤ VIN ≤ 24V
Conditions
Min
100
200
13V ≤ VIN ≤ 24V
90
150
1 mA ≤ IO ≤ 100 mA
20
90
1 mA ≤ IO ≤ 40 mA
10
45
2
5.5
11.5V ≤ VIN ≤ 24V
1.5
1 mA ≤ IO ≤ 40 mA
0.1
Output Noise Voltage
Ripple Rejection
f = 120 Hz
15V ≤ VIN ≤ 25V
38
Peak Output Current
IPK
Average Output Voltage Tempco
VIN (Min)
IO = 5 mA
Minimum Value of Input Voltage
Required to Maintain Line Regulation
Units
mV
mA
70
µV
44
dB
140
mA
−0.9
mV/˚C
10.7
V
LM78L12AC
Unless otherwise specified, VIN = 19V
Symbol
VO
∆VO
Parameter
Conditions
Output Voltage
Line Regulation
∆VO
Load Regulation
IQ
Quiescent Current
∆IQ
Quiescent Current Change
Min
Typ
Max
11.5
12
12.5
14.5V ≤ VIN ≤ 27V
1 mA ≤ IO ≤ 40 mA
(Note 3)
11.4
12.6
1 mA ≤ IO ≤ 70 mA
(Note 3)
11.4
12.6
14.5V ≤ VIN ≤ 27V
30
180
16V ≤ VIN ≤ 27V
20
110
1 mA ≤ IO ≤ 100 mA
30
100
1 mA ≤ IO ≤ 40 mA
10
50
3
5
16V ≤ VIN ≤ 27V
1
1 mA ≤ IO ≤ 40 mA
Vn
IPK
Peak Output Current
Average Output Voltage Tempco
VIN (Min)
www.national.com
f = 120 Hz
15V ≤ VIN ≤ 25
IO = 5 mA
Minimum Value of Input Voltage
Required to Maintain Line Regulation
mV
mA
40
80
µV
54
dB
140
mA
−1.0
mV/˚C
13.7
4
V
0.1
Output Noise Voltage
Ripple Rejection
Units
14.5
V
Unless otherwise specified, VIN = 23V
Symbol
VO
Parameter
Conditions
Output Voltage
∆VO
Line Regulation
∆VO
Load Regulation
IQ
Quiescent Current
∆IQ
Quiescent Current Change
Min
Typ
Max
14.4
15.0
15.6
17.5V ≤ VIN ≤ 30V
1 mA ≤ IO ≤ 40 mA
(Note 3)
14.25
15.75
1 mA ≤ IO ≤ 70 mA
(Note 3)
14.25
15.75
17.5V ≤ VIN ≤ 30V
37
250
20V ≤ VIN ≤ 30V
25
140
1 mA ≤ IO ≤ 100 mA
35
150
1 mA ≤ IO ≤ 40 mA
12
75
3
5
20V ≤ VIN ≤ 30V
Vn
f = 120 Hz
18.5V ≤ VIN ≤ 28.5V
Peak Output Current
IPK
Average Output Voltage Tempco
VIN (Min)
IO = 5 mA
Minimum Value of Input Voltage
Required to Maintain Line Regulation
mV
0.1
Output Noise Voltage
Ripple Rejection
V
mA
1
1 mA ≤ IO ≤ 40 mA
Units
37
90
µV
51
dB
140
mA
−1.3
mV/˚C
16.7
17.5
V
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device
outside of its stated operating conditions.
Note 2: Human body model, 1.5 kΩ in series with 100 pF.
Note 3: Power dissipation ≤ 0.75W.
Note 4: Recommended minimum load capacitance of 0.01 µF to limit high frequency noise.
Note 5: Typical thermal resistance values for the packages are:
Z Package: θJC = 60 ˚C/W, = θJA = 230 ˚C/W
M Package: θJA = 180 ˚C/W
micro SMD Package: θJA = 230.9˚C/W
5
www.national.com
LM78LXX Series
LM78L15AC
LM78LXX Series
Typical Performance Characteristics
Maximum Average Power
Dissipation (Z Package)
Dropout Voltage
Peak Output Current
DS007744-17
DS007744-16
DS007744-14
Ripple Rejection
Output Impedance
DS007744-18
DS007744-19
Quiescent Current
DS007744-21
www.national.com
Quiescent Current
6
DS007744-20
LM78LXX Series
Equivalent Circuit
LM78LXX
DS007744-7
Typical Applications
Fixed Output Regulator
DS007744-8
*Required if the regulator is located more than 3" from the power supply filter.
**See (Note 4) in the electrical characteristics table.
7
www.national.com
LM78LXX Series
Typical Applications
(Continued)
Adjustable Output Regulator
DS007744-9
VOUT = 5V + (5V/R1 + IQ) R2
5V/R1 > 3 IQ, load regulation (Lr) ≈ [(R1 + R2)/R1] (Lr of LM78L05)
Current Regulator
DS007744-10
IOUT = (VOUT/R1) + IQ
> IQ = 1.5 mA over line and load changes
5V, 500 mA Regulator with Short Circuit Protection
DS007744-11
*Solid tantalum.
**Heat sink Q1.
***Optional: Improves ripple rejection and transient response.
Load Regulation: 0.6% 0 ≤ IL ≤ 250 mA pulsed with tON = 50 ms.
± 15V, 100 mA Dual Power Supply
DS007744-12
*Solid tantalum.
www.national.com
8
LM78LXX Series
Typical Applications
(Continued)
Variable Output Regulator 0.5V-18V
DS007744-13
*Solid tantalum.
VOUT = VG + 5V, R1 = (−VIN/IQ LM78L05)
VOUT = 5V (R2/R4) for (R2 + R3) = (R4 + R5)
A 0.5V output will correspond to (R2/R4) = 0.1 (R3/R4) = 0.9
9
www.national.com
LM78LXX Series
Physical Dimensions
inches (millimeters) unless otherwise noted
NOTES: UNLESS OTHERWISE SPECIFIED
1. EPOXY COATING
2. 63Sn/37Pb EUTECTIC BUMP
3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.
4. PIN 1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE
NUMBERED COUNTERCLOCKWISE.
5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT.
6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC.
8-Bump micro SMD
Order Number LM78L05IBP or LM78L05IBPX
NS Package Number BPA08AAA
X1 = 1.285 X2 = 1.285 X3 = 0.7
www.national.com
10
LM78LXX Series
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
S.O. Package (M)
Order Number LM78L05ACM, LM78L12ACM or LM78L15ACM
NS Package Number M08A
Molded Offset TO-92 (Z)
Order Number LM78L05ACZ, LM78L09ACZ, LM78L12ACZ,
LM78L15ACZ, LM78L62ACZ or LM78L82ACZ
NS Package Number Z03A
11
www.national.com
LM78LXX Series 3-Terminal Positive Regulators
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Similar pages