Artesyn AIF04ZPFC-01NL Up to 1600 w output power Datasheet

POWER
AIF - PFC Series
1600 Watts
Data Sheet
Total Power: 1600 Watts
120 - 370 VDC (Configurable)
Input Voltage: 85 - 264 VAC
# of Outputs: Single
SPECIAL FEATURES
ƒƒ Unity power factor
ƒƒ High efficiency - up to 95%
ƒƒ Universal input voltage and
frequency range
ƒƒ Up to 1600 W output power
ƒƒ Positive and Negative enable
function
ƒƒ Parallelable with accurate current
sharing
ƒƒ <10% harmonic distortion conforming to IEC1000-3-2 Compliance
ƒƒ 100°C baseplate operating
temperature
ƒƒ DC Input option
ƒƒ Power fail warning signal
ƒƒ Enable output to control DC-DC
Converter
ƒƒ EEPROM data storage via I2C
Interface
ƒƒ External inrush current limited
protection
ƒƒ Power density up to 290 W/in3
ƒƒ Two year warranty
SAFETY
ƒƒ UL
ƒƒ cUL
ƒƒ TUV
60950 Recognized
60950 Recognized
EN60950 Licensed
Electrical Specifications
Input
Input range
85 - 264 Vac / 120 - 370 Vdc (configurable)
Input surge
290 Vac / 1s
Input Frequency
50/60 Hz
Efficiency
95% @ 230 Vac, 1600 W (typical)
Total Harmonic Distortion
Less than 10%
Power Factor
0.99 typical (Po ± 500 W); 0.97 typical (Po ± 1000 W)
Output
Output Voltage
380V typical (Io =4.2 A / Vi > 180 Vac); 393 V typical (Io = 0A)
Note: Vin peak must always be lower than Vout
Current Share Accuracy
10% max
Overvoltage Protection
430 max
Power Limit for AC input
for DC input
Vin = 85 Vac, Pmax = 1000W; Vin = 230 Vac, Pmax = 1600W Case;
Vin = 370 Vdc, Pmax =1600W
Control
Power Fail Warning
Direct drive output to opto-isolator
Power Fail Warning Adjust
195 to 355 Vdc adjustable
LD Enable
Direct drive output to opto-isolator
PFC Enable
TTL compatiable
Voltage Adjust
76% to 100% Vo
DC Input Enable
Clock Input (external sync)
6 Vp-p typical @ 1 MHz ± 5%
Clock Output (int. clock)
6 Vp-p typical @ 1 MHz ± 5%
Temperature Monitor Output 10 mV/°C
Current Monitor Output
0 to 1 mA (1 mA = 4.2 A output)
I2C Interface
Notes: Nominal values apply with sense pins disconnected and other control pin unconnected.
AIF-PFC Series Data Sheet
Environmental Specifications
Operating temperature
-20 °C to +100 °C (baseplate temperature)
Startup temperature
-40 °C to +100 °C (baseplate temperature)
Storage temperature
-40 °C to +120 °C
Overtemperature protection
120 °C max
MTBF
1million hours
Ordering Information
Model Number
Description
Notes
AIF04ZPFC-01L 1600 W Low Profile PC Module
For parallel operation the total input current must be <16Arms.
AIF04ZPFC-02L 1600 W Low Profile PC Module
Designed for parallel operation where the total input current >16Arms, requires external
rail rectifiers.
AIF04ZPFC-01NL
Negative Enable
AIF04ZPFC-01NL
Negative Enable
1. Fon Non-thread hole, add suffix “-NT”.
Pin Assignments
Input (AC)
Output
Control Pins
31. L1
21. Positive
1. PV Aux -
32. L1
22. Positive
2. Temp Mon
33. L2
23. Negative
3. C Mon
34. L2
24. Negative
4. C Share
5. Clk Out
6. Clk In
7. PV Aux +
8. SDA
9. SCL
10. DC Enable
11. V Adj
12. PFW Adj
13. S Gnd
14. PFW
15. LD Enable
16. PF Enable
AIF-PFC Series Data Sheet
Mechanical Drawings
WORLDWIDE OFFICES
Americas
Europe (UK)
Asia (HK)
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded
Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or
for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo
are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are
trade names, trademarks, or registered trademarks of their respective owners.
© 2015 Artesyn Embedded Technologies, Inc.
www.artesyn.com
For more information: www.artesyn.com/power
For support: [email protected]
AIF-PFC Series-DS 11Feb2015
Similar pages