规格书编号： SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDBF15620A62 SF6-2 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2010-7-5 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子股份有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 6 SAW FILTER HDBF15620A62 SF6-2 更改内容描述 Modify Content 备注 Remark 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 2 of 6 SAW FILTER HDBF15620A62 SF6-2 1. SCOPE This specification shall cover the characteristics of SAW filter HD BF15620A62 2. ELECTRICAL SPECIFICATION Max Incident Power in Passband Max voltage between any 2 terminals Storage Temperature Range 10 dBm 30 VDC -50 to +125 ℃ 2.2Electronic Characteristics Parameter Center Frequency Insertion Loss -1dB Bandwidth -3dB Bandwidth -40dB Bandwidth Amplitude Ripple (146~166MHz) Group Delay Ripple(146~166MHz) Absolute Delay Input VSWR Output VSWR Stopband Rejection 0~123MHz, 190MHz~1GHz Input/Output Impedance Operating Temperature Range Material Temperature coefficient www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 Min 20.0 21.0 45 Typ 156 10.0 22.0 24.0 27.0 1.0 30 1.13 1.4 1.4 Max 12.0 30.0 1.8 100 1.5 2 2 Units MHz dB MHz MHz MHz dB ns us 50 dB 50 ohm ℃ ppm/℃ -40 +85 -94 E-mail:[email protected] Page 3 of 6 SAW FILTER www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 HDBF15620A62 E-mail:[email protected] SF6-2 Page 4 of 6 SAW FILTER HDBF15620A62 SF6-2 3. DIMENSION 4.TEST CIRCUIT L1 = 56nH, L2 = 56nH C1 =27pF, C2 = 33pF * Component values may vary due to actual PCB layout and parasitics. 5. ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 6 SAW FILTER HDBF15620A62 SF6-2 5-2 Low temperature exposure Subject the device to -20℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-3 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +80℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in 2.2. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in t2.2. 5-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 2.2. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 2.2. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2.2. 6. REMARK 7.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 7.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 7.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 6