APL5155 High Input Voltage, Low Quiescent Current, 150mA LDO Regulator Features General Description • Wide Input Voltage Range: 5.4V to 25V • Ultra Low Ground Current: 10µA The APL5155 is a low ground current linear regulator, which operates with input voltage from 5.4V to 25V and • High Output Accuracy: ±2.5% • Excellent Load/Line Transient • Low Dropout Voltage: 750mV @ 150mA • Fixed Output Voltages for 5V/3.3V or Adjustable delivers output current up to 150mA. Typical dropout voltage is only 750mV at 150mA loading. This combination of the high voltage and the low ground current makes the APL5155 ideal for USB and portable devices, using 2cell or 3-cell Li-Ion battery inputs. The APL5155 is stable with aluminum, tantalum, and Voltage • Built-In Current-Limit Protection • Built-In Over-Temperature Protection • Zero Shutdown Current • Internal Soft-Start Function • POR Scheme to Prevent VOUT Spike • SOT-23-5, SOT-89, and SOP-8P Packages • Lead Free and Green Devices Available ceramic capacitors. It requires a 1µF or greater capacitor for stability. The APL5155 has many protection functions, including over-temperature, current-limit and short circuit current limit protections, which prevent the device from thermal over-load and current over-load. The APL5155 regulator is available in miniature SOT-235, SOT-89, and SOP-8P packages. (RoHS Compliant) Pin Configuration Applications • USB Power Supply • Keep-Alive Supply in Notebook and Portable VIN 1 GND 2 EN 3 5 VOUT 4 NC/ADJ Computers • Logic Supply for High-Voltage Batteries • Battery Powered Systems SOT-23-5 (Top View) GND 1 VIN 2 TAB : VIN VOUT 3 SOT-89 (Top View) VOUT NC NC NC/ADJ 1 2 3 4 8 7 6 5 VIN GND NC EN SOP-8P (Top View) = Thermal Pad (connected to GND plane for better heat dissipation) ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 1 www.anpec.com.tw APL5155 Ordering and Marking Information Package Code B : SOT-23-5 D : SOT-89 KA : SOP-8P Operating Ambient Temperature Range I : -40 to 85 oC Handling Code TR : Tape & Reel Voltage Code 33 : 3.3V 50 : 5.0V Blank : Adjustable Version Assembly Material G : Halogen and Lead Free Device APL5155 Assembly Material Handling Code Temperature Range Package Code Voltage Code APL5155 B : L55X X - Date Code APL5155 33B : 55RX X - Date Code ; R - 3.3V APL5155 50B : 55ZX X - Date Code ; Z - 5.0V APL5155 D : APL5155 XXXXX XXXXX - Date Code APL5155 KA : APL5155 XXXXX XXXXX - Date Code Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for MSL classification at lead-free peak reflow temperature. ANPEC defines “Green” to mean lead-free (RoHS compliant) and halogen free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight). Absolute Maximum Ratings Symbol VIN, VEN VOUT, VADJ TJ TSTG TSDR (Note 1) Parameter Rating Unit VIN, EN to GND Voltage - 0.3 to 27 V VOUT, ADJ to GND Voltage - 0.3 to 27 Maximum Junction Temperature Storage Temperature Maximum Lead Soldering Temperature, 10 Seconds V 150 o -65 to 150 o 260 o C C C Note1: Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Thermal Characteristics Symbol Parameter Typical Value Unit Thermal Resistance-Junction to Ambient (Note 2) θJA SOT-23-5 SOT-89 SOP-8P 235 180 50 SOT-23-5 SOT-89 SOP-8P 130 38 20 o C/W Thermal Resistance-Junction to Ambient (Note 2) θJC o C/W Note 2: θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 2 www.anpec.com.tw APL5155 Recommended Operating Conditions (Note 3) Symbol Parameter Range Unit VIN VIN to GND Voltage 5.4 to 25 V IOUT VOUT Source Current 0 to 150 mA VOUT Adjustable Output Voltage 1.24 to 20 V V VEN EN Pin Input Voltage 0 to 25 COUT Output Capacitance 1 to 4.7 µF ESR The ESR of Output Capacitance 5 to 50 mΩ TA TJ Ambient Temperature Junction Temperature -40 to 85 o -40 to 125 o C C Note 3: Refer to the typical application circuit. Electrical Characteristics Unless otherwise noted, these specifications apply over VIN=VOUT+3V, CIN=1µF, COUT=2.2µF, TA=-40 to 85oC. Symbol Parameter Test Conditions APL5155 Min. Typ. Max. Unit POWER-ON-RESET (POR) AND SUPPLY CURRENT VIN Input Voltage 5.4 - 25 V Rising VIN POR Threshold 4.5 5 5.25 V - 200 - mV IOUT=0mA, EN=high, Adj mode - 10 20 IOUT=0mA, EN=high, Fix Mode - 15 25 EN=Low, VIN=19V - 1 3 µA - 1.24 - V -2.5 - 2.5 % ppm VIN POR Hysteresis IQ IQSHDN Quiescent Current Shutdown Supply Current µA REFERENCE AND OUTPUT VOLTAGE VREF Reference Voltage VREF Voltage Accuracy VREF Temperature Coefficient VOUT Output Voltage Output Voltage Accuracy IOUT Adjustable Voltage Version o IOUT=10mA, TA=25 C o TJ=-40 to 125 C - 50 - Fixed Voltage Version - 3.3 - Fixed Voltage Version - 5.0 - IOUT=10mA, TA=25oC -2.5 - 2.5 % 0 - 150 mA - 0.1 0.5 % % Load Current Range V REGLINE Line Regulation VOUT+3V<VIN<25V, IOUT=1mA, VOUT=5V REGLOAD Load Regulation 0.1mA<IOUT<150mA, VOUT=5V - 0.6 1.4 IOUT=30mA, VOUT=20V - 160 240 IOUT=100mA, VOUT=20V - 500 750 IOUT=150mA, VOUT=20V - 750 1125 IOUT=10mA, VOUT=5V - 150 225 TJ rising - 150 - °C - 30 - °C VDROP Dropout Voltage mV PROTECTIONS TOTP Over-Temperature Threshold Over-Temperature Hysteresis Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 3 www.anpec.com.tw APL5155 Electrical Characteristics (Cont.) Unless otherwise noted, these specifications apply over VIN=VOUT+3V, CIN=1µF, COUT=2.2µF, TA=-40 to 85oC. Symbol Parameter Test Conditions APL5155 Min. Unit Typ. Max. 200 - 400 mA - 50 - mA PROTECTIONS (CONT.) ILIMIT Current-Limit VIN=VOUT +3V, to 25V ISHORT Short-Circuit Current VOUT=0V, only for Fix mode SOFT-START AND SHUTDOWN TSS IEN Soft-Start Interval From VEN rising to VOUT=90% EN Input Logic HIGH IC is enabled EN Input Logic LOW IC is shut down EN Input Logic Hysteresis VOUT+3V<VIN<25V - 0.2 - V EN Pin Input Bias Current VEN=25V - 0.1 1 µA Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 4 - 1 - ms 2.5 - - V 0 - 0.6 V www.anpec.com.tw APL5155 Typical Operating Characteristics Quiescent Current vs. Input Voltage Quiescent Current vs. Output Current 300 12 VIN =12V 11 Quiescent Current (µA) Quiescent Current (µA) No Load 10 9 8 7 250 200 150 100 50 6 0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 Input Votlage (V) 0 125 150 1.0 14 VIN =8V, No Load VOUT=20V 0.9 12 0.8 Dropout Voltage (V) Quiescent Current (µA) 50 75 100 Output Current (mA) Dropout Voltage vs. Output Current Quiescent Current vs. Junction Temperature 10 8 6 4 0.7 0.6 0.5 0.4 0.3 0.2 2 0 0.1 -40 -20 0 20 40 60 80 0 100 120 0 25 50 75 100 Junction Temperature ( oC) Output Current (mA) Reference Voltage vs. Junction Temperature PSRR vs. Frequency 1.260 1.255 125 150 0 VIN =8V -10 VIN=12V, VIN=3.3V, CIN=1µF, COUT=2.2µF -20 1.250 -30 1.245 PSRR (dB) Reference Voltage (V) 25 1.240 1.235 -40 -50 -60 -70 1.230 -80 1.225 1.220 -40 -20 -90 0 20 40 60 80 -100 0.1 100 120 o Junction Temperature ( C) Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 5 1 10 100 Frequency (kHz) 1000 www.anpec.com.tw APL5155 Operating Waveforms The test condition is TA=25oC unless otherwise specified. Turn On Response Turn Off Response VE N VE N 1 1 VOUT V OUT 2 2 VIN=12V, VOUT=3.3V, ROUT=33Ω, CIN=1µF/X7R, COUT=2.2µF/X7R CH1: VEN, 5V/Div, DC CH2: VOUT, 1V/Div, DC TIME: 0.2ms/Div VIN=12V, VOUT=3.3V, ROUT=33Ω, CIN=1µF/X7R, COUT=2.2µF/X7R CH1: VEN, 5V/Div, DC CH2: VOUT, 1V/Div, DC TIME: 0.5ms/Div Power On Power Off VIN VIN VOUT VOUT 1,2 1,2 VIN=12V, VOUT=3.3V, ROUT=33Ω, CIN=1µF/X7R, COUT=2.2µF/X7R VIN=12V, VOUT=3.3V, ROUT=33Ω, CIN=1µF/X7R, COUT=2.2µF/X7R CH1: VIN, 2V/Div, DC CH2: VOUT, 1V/Div, DC TIME:5ms/Div Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 CH1: VIN, 2V/Div, DC CH2: VOUT, 1V/Div, DC TIME:5ms/Div 6 www.anpec.com.tw APL5155 Operating Waveforms (Cont.) The test condition is TA=25oC unless otherwise specified. Load Transient Response Line Transient Response VOUT 1 VIN 1 V OUT 2 IOUT 2 VIN=12V, VOUT=3.3V, CIN=1µF/X7R, COUT=2.2µF/X7R, IOUT=3-150-3mA, Falling/Rising Slew Rate=1A/µs CH1: VOUT, 100mV/Div, offset=3.3V CH2: IOUT, 100mA/Div, DC TIME: 50µs/Div VIN=11.5-12.5-11.5V, Falling/Rising=1µs, VOUT=3.3V, IOUT=10mA, CIN=1µF/X7R, COUT=2.2µF/X7R CH1: VIN, 1V/Div, Offset=11.5V CH2: VOUT, 50mV/Div, Offset=3.3V TIME: 50µs/Div Pin Description PIN FUNCTION NO. NAME SOT-23-5 SOT-89 SOP-8P 1 2 8 VIN Voltage Supply Input Pin. 2 1 7 GND Ground. 3 - 5 EN 4 - 4 NC/ADJ 5 3 1 VOUT - - 2, 3, 6 NC Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 Enable Input Pin. Logic low=shutdown; logic high=enable. NC: No Connection (fixed output voltage version). ADJ: Output Voltage Feedback Pin (adjust output voltage version). Regulator Output Pin. No Connection. 7 www.anpec.com.tw APL5155 Block Diagram 1. Adjust Output Voltage (SOT-23-5/SOP-8P) VIN CurrentLimit POR EN Control Logic VREF 1.24V SoftStart VOUT OTP Short-Circuit Current-Limit ADJ GND 2. Fixed Output Voltage (SOT-23-5/SOP-8P) VIN CurrentLimit POR EN Control Logic VREF 1.24V SoftStart VOUT OTP Short-Circuit Current-Limit GND Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 8 www.anpec.com.tw APL5155 Block Diagram (Cont.) 3. Fixed Output Voltage (SOT-89) VIN CurrentLimit POR Control Logic VREF 1.24V SoftStart VOUT OTP Short-Circuit Current-Limit GND Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 9 www.anpec.com.tw APL5155 Typical Application Circuit 1. Adjust Output Voltage (SOT-23-5/SOP-8P) VIN CIN 1µF VOUT VIN APL5155 VOUT B APL5155 EN KA ADJ R1 GND R2 ON COUT 2.2µF OFF VOUT=1.24V x (R1+R2)/R2 2. Fixed Output Voltage (SOT-23-5/SOP-8P) VIN VOUT VIN VOUT CIN 1µF ON COUT EN 2.2µF GND OFF 3. Fixed Output Voltage (SOT-89) VIN CIN 1µF Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 VOUT VIN APL5155 VOUT B APL5155 KAGND 10 COUT 2.2µF www.anpec.com.tw APL5155 Application Information Enable/Shutdown PD(MAX ) = The APL5155 features an active-high enable pin that allows the regulator to be disabled. Forcing the enable pin TJ − TA θJA where TJ-TA is the temperature difference between the junction and ambient air. θJA is the thermal resistance between junction and ambient air. low disables the regulator, so current consumed by the regulator goes nearly to zero. Forcing the enable pin high enables the output voltage. The enable pin can not float. For continual operation, do not exceed the absolute maximum junction temperature rating of TJ=125oC. Input Capacitor For example: In SOT-23-5 package θJA=235oC/W. When operates the The APL5155 has high input voltage up to 25V. The input capacitor must be rated to sustain voltages that may be APL5155 at TA=50 oC, the maximum power dissipation can be determined as below: used on the input. An input capacitor may be required when the device is not near the source power supply or PD(MAX)=(125oC-50oC)/(235oC/W) PD(MAX)=319.1mW when supplied by a battery. Small and surface-mounted ceramic capacitors can be used for bypassing. A larger value may be required if the source supply has high ripple. Thermal Pad Consideration Output Capacitor The SOP-8P is a cost-effective package which features a small size, like a standard SOP-8, and a bottom thermal The APL5155 requires an output capacitor for stability. The design requires 1µF or greater on the output to main- pad to minimize the thermal resistance of the package is applicable to high current applications. The thermal pad tain stability. It is optimized by using low-ESR ceramic chip capacitors. The maximum allowable ESR is 3Ω. More must be soldered down to the copper plane on circuit board. Heat can be conducted away from the thermal capacitance improves transient response. Place the out- pad through the copper plane to ambient. If the copper plane is not on the top surface of the circuit board, 4 or 6 put capacitor as close to the VOUT pin as possible. X7R/X5R dielectric-type ceramic capacitors are recom- vias should be used to thermally couple the thermal pad to the bottom plane. mended because of their temperature performance. X7R type capacitors change capacitance by 15% over their For good thermal conduction, the vias must be plated through and solder filled. The copper plane used to con- operating temperature ranges. To use a ceramic chip capacitor with Y5V dielectric, the value must be much duct heat away from the thermal pad should be as large as practical. higher than an X7R ceramic capacitor to ensure the same minimum capacitance over the equivalent operating temperature range. 0.072 0.118 No-Load Stability 0.024 The APL5155 will remain stable and in regulation with no load unlike many other voltage regulators. This is especially important in CMOS RAM keep-alive applications. 0.150 Thermal Consideration The thermal resistance of junction to ambient controls the APL5155's maximum power dissipation. The power 0.212 dissipation across the device is PD=IOUT (VIN-VOUT), and the maximum power dissipation is: Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 ground plane for thermal pad SOP-8P Layout Recommendation 11 www.anpec.com.tw APL5155 Application Information (Cont.) Adjustable Regulator Application SOP-8P The output voltage of APL5155 can be adjusted from 3V 0.024 7 6 5 0.138 where VREF=1.24V The resistors should be placed as close the device as possible to avoid noise. 0.118 0.212 R VOUT = VREF 1 + 1 R2 8 0.072 to 20V by using two external resistors. The resistors set the output voltage based on the following equation: Recommended Minimum Footprint 1 SOT-23-5 2 0.050 4 Unit : Inch 0.05 0.1 0.076 3 0.038 0.02 Unit : Inch SOT-89 0.067 0.104 0.140 0.076 0.059 0.022 Unit : Inch Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 12 www.anpec.com.tw APL5155 Package Information SOT-23-5 D e E E1 SEE VIEW A b c 0.25 A L 0 GAUGE PLANE SEATING PLANE A1 A2 e1 VIEW A S Y M B O L SOT-23-5 INCHES MILLIMETERS MIN. MIN. MAX. A MAX. 0.057 1.45 A1 0.00 0.15 0.000 0.006 A2 0.90 1.30 0.035 0.051 b 0.30 0.50 0.012 0.020 c 0.08 0.22 0.003 0.009 D 2.70 3.10 0.106 0.122 0.118 0.071 E 2.60 3.00 0.102 E1 1.40 1.80 0.055 e 0.95 BSC e1 1.90 BSC 0.037 BSC 0.075 BSC L 0.30 0.60 0 0° 8° 0.012 0° 0.024 8° Note : 1. Follow JEDEC TO-178 AA. 2. Dimension D and E1 do not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 10 mil per side. Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 13 www.anpec.com.tw APL5155 Package Information SOT-89 A C L H E E1 D D1 e e1 B B1 S Y M B O L A SOT-89 MILLIMETERS INCHES MIN. MAX. MIN. MAX. 1.40 1.60 0.055 0.063 0.022 B 0.44 0.56 0.017 B1 0.36 0.48 0.014 0.019 0.017 C 0.35 0.44 0.014 D 4.40 4.60 0.173 0.181 D1 1.62 1.83 0.064 0.072 E 2.29 2.60 0.090 0.102 E1 2.13 2.29 0.084 0.090 e 1.50 BSC e1 3.00 BSC 0.059 BSC 0.118 BSC H 3.94 4.25 0.155 0.167 L 0.89 1.20 0.035 0.047 Note : Follow JEDEC TO-243 AA. Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 14 www.anpec.com.tw APL5155 Package Information SOP-8P -T- SEATING PLANE < 4 mils D SEE VIEW A h X 45o E THERMAL PAD E1 E2 D1 c A1 0.25 A2 A b e GAUGE PLANE SEATING PLANE θ L VIEW A S Y M B O L A SOP-8P INCHES MILLIMETERS MAX. MIN. MIN. MAX. 1.60 A1 0.00 0.063 0.15 0.000 0.006 0.049 A2 1.25 b 0.31 0.51 0.012 0.020 c 0.17 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 D1 2.50 3.50 0.098 0.138 E 5.80 6.20 0.228 0.244 0.157 0.118 E1 3.80 4.00 0.150 E2 2.00 3.00 0.079 e 1.27 BSC 0.050 BSC h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 0o C 8o C θ 0oC 8o C Note : 1. Followed from JEDEC MS-012 BA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E" does not include inter-lead flash or protrusions. Inter-lead flash and protrusions shall not exceed 10 mil per side. Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 15 www.anpec.com.tw APL5155 Carrier Tape & Reel Dimensions P0 P2 P1 A B0 W F E1 OD0 K0 A0 A OD1 B B T SECTION A-A SECTION B-B H A d T1 Application SOT-23-5 Application SOT-89 Application SOP-8P A H T1 C d D W E1 F 178.0±2.00 50 MIN. 8.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. 8.0±0.30 1.75±0.10 3.5±0.05 P0 P1 P2 D0 D1 T A0 B0 K0 2.0±0.05 1.5+0.10 -0.00 1.0 MIN. 0.6+0.00 -0.40 3.20±0.20 3.10±0.20 1.50±0.20 4.0±0.10 4.0±0.10 A H T1 C d D W E1 F 178.0±2.00 50 MIN. 12.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. 12.0±0.30 1.75±0.10 5.50±0.05 P0 P1 P2 D0 D1 T A0 B0 K0 4.0±0.10 8.0±0.10 2.0±0.05 1.5+0.10 -0.00 1.5 MIN. 0.6+0.00 -0.40 4.80±0.20 4.50±0.20 1.80±0.20 A H T1 C d D W E1 F 330.0±2.00 50 MIN. 12.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. 12.0±0.30 1.75±0.10 5.5±0.05 P0 P1 P2 D0 D1 T A0 B0 K0 2.0±0.05 1.5+0.10 -0.00 1.5 MIN. 0.6+0.00 -0.40 6.40±0.20 5.20±0.20 2.10±0.20 4.0±0.10 8.0±0.10 (mm) Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 16 www.anpec.com.tw APL5155 Devices Per Unit Package Type Unit Quantity SOT-23-5 Tape & Reel 3000 SOT-89 Tape & Reel 1000 SOP-8P Tape & Reel 2500 Taping Direction Information SOT-23-5 USER DIRECTION OF FEED SOT-89 USER DIRECTION OF FEED Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 17 www.anpec.com.tw APL5155 Taping Direction Information SOP-8P USER DIRECTION OF FEED Classification Profile Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 18 www.anpec.com.tw APL5155 Classification Reflow Profiles Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly 100 °C 150 °C 60-120 seconds 150 °C 200 °C 60-120 seconds 3 °C/second max. 3°C/second max. 183 °C 60-150 seconds 217 °C 60-150 seconds See Classification Temp in table 1 See Classification Temp in table 2 Time (tP)** within 5°C of the specified classification temperature (Tc) 20** seconds 30** seconds Average ramp-down rate (Tp to Tsmax) 6 °C/second max. 6 °C/second max. 6 minutes max. 8 minutes max. Preheat & Soak Temperature min (Tsmin) Temperature max (Tsmax) Time (Tsmin to Tsmax) (ts) Average ramp-up rate (Tsmax to TP) Liquidous temperature (TL) Time at liquidous (tL) Peak package body Temperature (Tp)* Time 25°C to peak temperature * Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum. ** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum. Table 1. SnPb Eutectic Process – Classification Temperatures (Tc) Package Thickness <2.5 mm ≥2.5 mm Volume mm <350 235 °C 220 °C 3 Volume mm ≥350 220 °C 220 °C 3 Table 2. Pb-free Process – Classification Temperatures (Tc) Package Thickness <1.6 mm 1.6 mm – 2.5 mm ≥2.5 mm Volume mm <350 260 °C 260 °C 250 °C 3 Volume mm 350-2000 260 °C 250 °C 245 °C 3 Volume mm >2000 260 °C 245 °C 245 °C 3 Reliability Test Program Test item SOLDERABILITY HOLT PCT TCT HBM MM Latch-Up Method JESD-22, B102 JESD-22, A108 JESD-22, A102 JESD-22, A104 MIL-STD-883-3015.7 JESD-22, A115 JESD 78 Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 19 Description 5 Sec, 245°C 1000 Hrs, Bias @ Tj=125°C 168 Hrs, 100%RH, 2atm, 121°C 500 Cycles, -65°C~150°C VHBM≧2KV VMM≧200V 10ms, 1tr≧100mA www.anpec.com.tw APL5155 Customer Service Anpec Electronics Corp. Head Office : No.6, Dusing 1st Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 2F, No. 11, Lane 218, Sec 2 Jhongsing Rd., Sindian City, Taipei County 23146, Taiwan Tel : 886-2-2910-3838 Fax : 886-2-2917-3838 Copyright ANPEC Electronics Corp. Rev. A.3 - Sep., 2012 20 www.anpec.com.tw