TI1 LP38841 0.8a ultra low dropout linear regulators stable with ceramic output capacitor Datasheet

LP38841
www.ti.com
SNVS289B – DECEMBER 2004 – REVISED SEPTEMBER 2006
LP38841 0.8A Ultra Low Dropout Linear Regulators
Stable with Ceramic Output Capacitors
Check for Samples: LP38841
FEATURES
•
•
1
•
•
2
•
•
•
•
•
•
•
Ideal for conversion from 1.8V or 1.5V inputs
Designed for use with low ESR ceramic
capacitors
0.8V, 1.2V and 1.5V standard voltages
available
Ultra low dropout voltage (75mV @ 0.8A typ)
1.5% initial output accuracy
Load regulation of 0.1%/A (typical)
30nA quiescent current in shutdown (typical)
Low ground pin current at all loads
Over temperature/over current protection
Available in 5 lead TO220 and TO263 packages
−40°C to +125°C junction temperature range
APPLICATIONS
•
•
•
•
ASIC Power Supplies In:
– - Desktops, Notebooks, and Graphics
Cards, Servers
– - Gaming Set Top Boxes, Printers and
Copiers
Server Core and I/O Supplies
DSP and FPGA Power Supplies
SMPS Post-Regulator
DESCRIPTION
The LP38841 is a high current, fast response regulator which can maintain output voltage regulation with
minimum input to output voltage drop. Fabricated on a CMOS process, the device operates from two input
voltages: Vbias provides voltage to drive the gate of the N-MOS power transistor, while Vin is the input voltage
which supplies power to the load. The use of an external bias rail allows the part to operate from ultra low Vin
voltages. Unlike bipolar regulators, the CMOS architecture consumes extremely low quiescent current at any
output load current. The use of an N-MOS power transistor results in wide bandwidth, yet minimum external
capacitance is required to maintain loop stability.
The fast transient response of these devices makes them suitable for use in powering DSP, Microcontroller Core
voltages and Switch Mode Power Supply post regulators. The parts are available in TO-220 and TO-263
packages.
Dropout Voltage: 75 mV (typ) @ 0.8A load current.
Quiescent Current: 30 mA (typ) at full load.
Shutdown Current: 30 nA (typ) when S/D pin is low.
Precision Output Voltage: 1.5% room temperature accuracy.
Typical Application Circuit
LP38841
IN
IN
BIAS
5V ± 10%
4.7 PF*
BIAS
0.1 PF
OUT
OUT
10 PF
Ceramic
S/D
S/D
GND
GND
GND
* Minimum value required if Tantalum capacitor is used (see Application Hints).
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2006, Texas Instruments Incorporated
LP38841
SNVS289B – DECEMBER 2004 – REVISED SEPTEMBER 2006
www.ti.com
Connection Diagram
Figure 1. TO-220, Top View
Figure 2. TO-263, Top View
Pin Functions
Pin Descriptions
Pin Name
BIAS
OUTPUT
GND
INPUT
SHUTDOWN
Description
The bias pin is used to provide the low current bias voltage to the chip which operates the internal circuitry and
provides drive voltage for the N-FET.
The regulated output voltage is connected to this pin.
This is both the power and analog ground for the IC. Note that both pin three and the tab of the TO-220 and TO263 packages are at ground potential. Pin three and the tab should be tied together using the PC board copper
trace material and connected to circuit ground.
The high current input voltage which is regulated down to the nominal output voltage must be connected to this
pin. Because the bias voltage to operate the chip is provided seperately, the input voltage can be as low as a
few hundered millivolts above the output voltage.
This provides a low power shutdown function which turns the regulated output OFF. Tie to VBIAS if this function is
not used.
Block Diagram
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LP38841
LP38841
www.ti.com
SNVS289B – DECEMBER 2004 – REVISED SEPTEMBER 2006
Absolute Maximum Ratings
(1)
−65°C to +150°C
Storage Temperature Range
Lead Temp. (Soldering, 5 seconds)
ESD Rating
Human Body Model
Machine Model (3)
Power Dissipation
260°C
(2)
2 kV
200V
(4)
Internally Limited
VIN Supply Voltage (Survival)
−0.3V to +6V
VBIAS Supply Voltage (Survival)
−0.3V to +7V
−0.3V to +7V
Shutdown Input Voltage (Survival)
IOUT (Survival)
Internally Limited
−0.3V to +6V
Output Voltage (Survival)
−40°C to +150°C
Junction Temperature
(1)
(2)
(3)
(4)
Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for
which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications, see
Electrical Characteristics. Specifications do not apply when operating the device outside of its rated operating conditions.
The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin.
The machine model is a 220 pF capacitor discharged directly into each pin.
At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink thermal values.
θJ-A for TO-220 devices is 65°C/W if no heatsink is used. If the TO-220 device is attached to a heatsink, a θJ-S value of 4°C/W can be
assumed. θJ-A for TO-263 devices is approximately 35°C/W if soldered down to a copper plane which is at least 1 square inch in area. If
power dissipation causes the junction temperature to exceed specified limits, the device will go into thermal shutdown.
Operating Ratings
VIN Supply Voltage
(VOUT + VDO) to 5.5V
Shutdown Input Voltage
0 to +5.5V
IOUT
0.8A
−40°C to +125°C
Operating Junction
Temperature Range
VBIAS Supply Voltage
4.5V to 5.5V
VOUT
0.8V to 1.5V
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LP38841
3
LP38841
SNVS289B – DECEMBER 2004 – REVISED SEPTEMBER 2006
www.ti.com
Electrical Characteristics
Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range.
Unless otherwise specified: VIN = VO(NOM) + 1V, VBIAS = 4.5V, IL = 10 mA, CIN = 10 µF CER, COUT = 22 µF CER, CBIAS = 1
µF CER, VS/D = VBIAS. Min/Max limits are guaranteed through testing, statistical correlation, or design.
Symbol
VO
Parameter
Conditions
Output Voltage Tolerance
10 mA < IL < 0.8A
VO(NOM) + 1V ≤ VIN ≤ 5.5V
4.5V ≤ VBIAS ≤ 5.5V
(2)
ΔVO/ΔVIN
Output Voltage Line Regulation
ΔVO/ΔIL
Output Voltage Load Regulation
VDO
Dropout Voltage
IQ(VIN)
Quiescent Current Drawn from VIN
Supply
(3)
(4)
Min
ISC
Quiescent Current Drawn from
VBIAS Supply
Short-Circuit Current
Max
0.8
0.812
0.824
1.182
1.164
1.2
1.218
1.236
1.478
1.455
1.5
1.523
1.545
0.01
Units
V
%/V
0.1
0.4
1.3
%/A
IL = 0.8A
75
120
205
mV
10 mA < IL < 0.8A
30
35
40
mA
0.06
1
30
µA
2
4
6
mA
VS/D ≤ 0.3V
0.03
1
30
µA
VOUT = 0V
2.6
VS/D ≤ 0.3V
IQ(VBIAS)
(1)
0.788
0.776
VO(NOM) + 1V ≤ VIN ≤ 5.5V
10 mA < IL < 0.8A
Typ
10 mA < IL < 0.8A
A
Shutdown Input
VSDT
Output Turn-off Threshold
Output = ON
Output = OFF
0.7
0.3
0.7
Td (OFF)
Turn-OFF Delay
RLOAD X COUT << Td (OFF)
20
Td (ON)
Turn-ON Delay
RLOAD X COUT << Td (ON)
15
IS/D
S/D Input Current
VS/D =1.3V
1
VS/D ≤ 0.3V
−1
Junction to Ambient Thermal
Resistance
TO-220, No Heatsink
65
TO-263, 1 sq.in Copper
35
PSRR (VIN)
Ripple Rejection for VIN Input
Voltage
VIN = VOUT +1V, f = 120 Hz
80
VIN = VOUT + 1V, f = 1 kHz
65
PSRR (VBIAS)
Ripple Rejection for VBIAS Voltage
VBIAS = VOUT + 3V, f = 120 Hz
58
VBIAS = VOUT + 3V, f = 1 kHz
58
en
Output Noise Density
f = 120 Hz
Output Noise Voltage
VOUT = 1.5V
BW = 10 Hz − 100 kHz
150
BW = 300 Hz − 300 kHz
90
θJ-A
1.3
V
µs
µA
°C/W
AC Parameters
(1)
(2)
(3)
(4)
4
1
dB
µV/root−H
z
µV (rms)
Typical numbers represent the most likely parametric norm for 25°C operation.
Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage.
Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from no load
to full load.
Dropout voltage is defined as the minimum input to output differential required to maintain the output with 2% of nominal value.
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LP38841
LP38841
www.ti.com
SNVS289B – DECEMBER 2004 – REVISED SEPTEMBER 2006
Typical Performance Characteristics
Unless otherwise specified: TJ = 25°C, CIN = 10 µF CER, COUT = 22 µF CER, CBIAS = 1 µF CER,S/D Pin is tied to VBIAS, VOUT
= 1.2V, IL = 10mA, VBIAS = 5V, VIN = VOUT + 1V.
VBIAS Transient Response
Dropout Voltage Over Temperature
0.12
125oC
VBIAS = 5V
6
DROPOUT VOLTAGE (V)
VBIAS (V)
0.10
VBIAS
5
25oC
0.08
-40oC
0.06
0.04
0.02
4
10
0
IL = 10 mA
-10
0
'VOUT (mV)
VOUT
0
0.2
0.4
0.6
0.8
ILOAD (A)
VOUT = 1.2V
VIN = 1.7V
20 Ps/DIV
VOUT
vs
Temperature
VBIAS PSRR
1.55
PSRR (dB)
1.54
1.53
VOUT (V)
1.52
1.51
1.50
1.49
1.48
1.47
1.46
100
90
_
80
_
70
_
60
_
50
_
40
_
30
_
20
_
10
_
0
1000
COUT = 4.7 PF Tantalum
ILOAD = 10 mA
10000
_
100000
_
1000000_
FREQUENCY (Hz)
1.45
-40 -20
0 20 40 60 80 100 120 140
TEMPERATURE (oC)
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LP38841
5
LP38841
SNVS289B – DECEMBER 2004 – REVISED SEPTEMBER 2006
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified: TJ = 25°C, CIN = 10 µF CER, COUT = 22 µF CER, CBIAS = 1 µF CER,S/D Pin is tied to VBIAS, VOUT
= 1.2V, IL = 10mA, VBIAS = 5V, VIN = VOUT + 1V.
VBIAS PSRR
VIN PSRR
80
COUT = 4.7 PF Tantalum
70
CBIAS = 1 PF Tantalum
60
IL = 10 mA
100
80
CBIAS = 1 PF Tantalum
IL = 0
PSRR (dB)
90
VOUT = 1.2V
PSRR (dB)
70
60
50
40
30
50
40
20
30
10
20
0
1000
10
0
100
10000
100000
1000000
FREQUENCY (Hz)
1000
10000
100000
1000000
FREQUENCY (Hz)
Application Hints
EXTERNAL CAPACITORS
To assure regulator stability, input and output capacitors are required as shown in the Typical Application Circuit.
OUTPUT CAPACITOR
An output capacitor is required on the LP3884X devices for loop stability. The minimum value of capacitance
necessary depends on type of capacitor: if a solid Tantalum capacitor is used, the part is stable with capacitor
values as low as 4.7µF. If a ceramic capacitor is used, a minimum of 22 µF of capacitance must be used
(capacitance may be increased without limit). The reason a larger ceramic capacitor is required is that the output
capacitor sets a pole which limits the loop bandwidth. The Tantalum capacitor has a higher ESR than the
ceramic which provides more phase margin to the loop, thereby allowing the use of a smaller output capacitor
because adequate phase margin can be maintained out to a higher crossover frequency. The tantalum capacitor
will typically also provide faster settling time on the output after a fast changing load transient occurs, but the
ceramic capacitor is superior for bypassing high frequency noise.
The output capacitor must be located less than one centimeter from the output pin and returned to a clean
analog ground. Care must be taken in choosing the output capacitor to ensure that sufficient capacitance is
provided over the full operating temperature range. If ceramics are selected, only X7R or X5R types may be
used because Z5U and Y5F types suffer severe loss of capacitance with temperature and applied voltage and
may only provide 20% of their rated capacitance in operation.
INPUT CAPACITOR
The input capacitor is also critical to loop stability because it provides a low source impedance for the regulator.
The minimum required input capacitance is 10 µF ceramic (Tantalum not recommended). The value of CIN may
be increased without limit. As stated above, X5R or X7R must be used to ensure sufficient capacitance is
provided. The input capacitor must be located less than one centimeter from the input pin and returned to a clean
analog ground.
BIAS CAPACITOR
The 0.1µF capacitor on the bias line can be any good quality capacitor (ceramic is recommended).
BIAS VOLTAGE
The bias voltage is an external voltage rail required to get gate drive for the N-FET pass transistor. Bias voltage
must be in the range of 4.5 - 5.5V to assure proper operation of the part.
6
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LP38841
LP38841
www.ti.com
SNVS289B – DECEMBER 2004 – REVISED SEPTEMBER 2006
UNDER VOLTAGE LOCKOUT
The bias voltage is monitored by a circuit which prevents the regulator output from turning on if the bias voltage
is below approximately 4V.
SHUTDOWN OPERATION
Pulling down the shutdown (S/D) pin will turn-off the regulator. Pin S/D must be actively terminated through a
pull-up resistor (10 kΩ to 100 kΩ) for a proper operation. If this pin is driven from a source that actively pulls high
and low (such as a CMOS rail to rail comparator), the pull-up resistor is not required. This pin must be tied to
VBIAS if not used.
POWER DISSIPATION/HEATSINKING
A heatsink may be required depending on the maximum power dissipation and maximum ambient temperature of
the application. Under all possible conditions, the junction temperature must be within the range specified under
operating conditions. The total power dissipation of the device is given by:
PD = (VIN−VOUT)IOUT+ (VIN)IGND
where IGND is the operating ground current of the device.
The maximum allowable temperature rise (TRmax) depends on the maximum ambient temperature (TAmax) of the
application, and the maximum allowable junction temperature (TJmax):
TRmax = TJmax− TAmax
The maximum allowable value for junction to ambient Thermal Resistance, θJA, can be calculated using the
formula:
θJA = TRmax / PD
These parts are available in TO-220 and TO-263 packages. The thermal resistance depends on amount of
copper area or heat sink, and on air flow. If the maximum allowable value of θJA calculated above is ≥ 60 °C/W
for TO-220 package and ≥ 60 °C/W for TO-263 package no heatsink is needed since the package can dissipate
enough heat to satisfy these requirements. If the value for allowable θJA falls below these limits, a heat sink is
required.
HEATSINKING TO-220 PACKAGE
The thermal resistance of a TO220 package can be reduced by attaching it to a heat sink or a copper plane on a
PC board. If a copper plane is to be used, the values of θJA will be same as shown in next section for TO263
package.
The heatsink to be used in the application should have a heatsink to ambient thermal resistance,
θHA≤ θJA − θCH − θJC.
In this equation, θCH is the thermal resistance from the case to the surface of the heat sink and θJC is the thermal
resistance from the junction to the surface of the case. θJC is about 3°C/W for a TO220 package. The value for
θCH depends on method of attachment, insulator, etc. θCH varies between 1.5°C/W to 2.5°C/W. If the exact value
is unknown, 2°C/W can be assumed.
HEATSINKING TO-263 PACKAGE
The TO-263 package uses the copper plane on the PCB as a heatsink. The tab of this package is soldered to
the copper plane for heat sinking. The graph below shows a curve for the θJA of TO-263 package for different
copper area sizes, using a typical PCB with 1 ounce copper and no solder mask over the copper area for heat
sinking.
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LP38841
7
LP38841
SNVS289B – DECEMBER 2004 – REVISED SEPTEMBER 2006
www.ti.com
Figure 3. θJA vs Copper (1 Ounce) Area for TO-263 package
As shown in the graph below, increasing the copper area beyond 1 square inch produces very little improvement.
The minimum value for θJA for the TO-263 package mounted to a PCB is 32°C/W.
Figure 4 shows the maximum allowable power dissipation for TO-263 packages for different ambient
temperatures, assuming θJA is 35°C/W and the maximum junction temperature is 125°C.
Figure 4. Maximum power dissipation vs ambient temperature for TO-263 package
8
Submit Documentation Feedback
Copyright © 2004–2006, Texas Instruments Incorporated
Product Folder Links: LP38841
MECHANICAL DATA
KTT0005B
TS5B (Rev D)
BOTTOM SIDE OF PACKAGE
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
9-Mar-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LP38841S-0.8
ACTIVE
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LP38841S
-0.8
LP38841S-0.8/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP38841S
-0.8
LP38841S-1.2
ACTIVE
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LP38841S
-1.2
LP38841S-1.2/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP38841S
-1.2
LP38841S-1.5
ACTIVE
DDPAK/
TO-263
KTT
5
45
TBD
Call TI
Call TI
-40 to 125
LP38841S
-1.5
LP38841S-1.5/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
45
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP38841S
-1.5
LP38841SX-0.8
ACTIVE
DDPAK/
TO-263
KTT
5
500
TBD
Call TI
Call TI
-40 to 125
LP38841S
-0.8
LP38841SX-0.8/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP38841S
-0.8
LP38841SX-1.2
ACTIVE
DDPAK/
TO-263
KTT
5
500
TBD
Call TI
Call TI
-40 to 125
LP38841S
-1.2
LP38841SX-1.2/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP38841S
-1.2
LP38841SX-1.5
ACTIVE
DDPAK/
TO-263
KTT
5
500
TBD
Call TI
Call TI
-40 to 125
LP38841S
-1.5
LP38841SX-1.5/NOPB
ACTIVE
DDPAK/
TO-263
KTT
5
500
Pb-Free (RoHS
Exempt)
CU SN
Level-3-245C-168 HR
-40 to 125
LP38841S
-1.5
LP38841T-0.8
ACTIVE
TO-220
KC
5
45
TBD
Call TI
Call TI
-40 to 125
LP38841T
-0.8
LP38841T-0.8/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP38841T
-0.8
LP38841T-1.2
ACTIVE
TO-220
KC
5
45
TBD
Call TI
Call TI
-40 to 125
LP38841T
-1.2
LP38841T-1.2/LF03
ACTIVE
TO-220
NDH
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
LP38841T-1.2/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
Addendum-Page 1
LP38841T
-1.2
-40 to 125
LP38841T
-1.2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
9-Mar-2013
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LP38841T-1.5
ACTIVE
TO-220
KC
5
45
TBD
Call TI
Call TI
-40 to 125
LP38841T
-1.5
LP38841T-1.5/NOPB
ACTIVE
TO-220
KC
5
45
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
-40 to 125
LP38841T
-1.5
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Only one of markings shown within the brackets will appear on the physical device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Nov-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LP38841SX-0.8
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP38841SX-0.8/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP38841SX-1.2
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP38841SX-1.2/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP38841SX-1.5
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
LP38841SX-1.5/NOPB
DDPAK/
TO-263
KTT
5
500
330.0
24.4
10.75
14.85
5.0
16.0
24.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
17-Nov-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP38841SX-0.8
DDPAK/TO-263
KTT
5
500
358.0
343.0
63.0
LP38841SX-0.8/NOPB
DDPAK/TO-263
KTT
5
500
358.0
343.0
63.0
LP38841SX-1.2
DDPAK/TO-263
KTT
5
500
358.0
343.0
63.0
LP38841SX-1.2/NOPB
DDPAK/TO-263
KTT
5
500
358.0
343.0
63.0
LP38841SX-1.5
DDPAK/TO-263
KTT
5
500
358.0
343.0
63.0
LP38841SX-1.5/NOPB
DDPAK/TO-263
KTT
5
500
358.0
343.0
63.0
Pack Materials-Page 2
MECHANICAL DATA
NDH0005D
www.ti.com
MECHANICAL DATA
KTT0005B
TS5B (Rev D)
BOTTOM SIDE OF PACKAGE
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LP38841EVAL LP38841MR-ADJ LP38841MRX-ADJ LP38841S-0.8 LP38841SX-0.8 LP38841SX-1.2 LP38841SX1.5 LP38841T-0.8 LP38841T-1.2 LP38841T-1.5