INTEGRATED CIRCUITS CBT3245A Octal bus switch Product data Supersedes data of 2002 Feb 18 Philips Semiconductors 2003 Jun 27 Philips Semiconductors Product data Octal bus switch CBT3245A FEATURES PIN CONFIGURATION — DHVQFN • Standard ’245-type pinout • 5 Ω switch connection between two ports • TTL compatible control input levels • Package options include plastic small outline (D), shrink small NC 1 outline (DB), thin shrink small outline (TSSOP) • Latch-up protection exceeds 500 mA per JESD78 • ESD protection exceeds 2000 V HBM per JESD22-A114, 150 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101 DESCRIPTION ** A1 2 19 OE A2 3 18 B1 A3 4 17 B2 A4 5 A5 6 15 A6 7 14 B5 A7 8 13 B6 A8 9 12 B7 GND* 10 The CBT3245A provides eight bits of high-speed TTL-compatible bus switching in a standard ’245 device pinout. The low on-state resistance of the switch allows connections to be made with minimal propagation delay. VCC 20 16 B3 B4 11 GND B8 * THE DIE SUBSTRATE IS ATTACHED TO THIS PAD USING CONDUCTIVE DIE ATTACH MATERIAL. IT CANNOT BE USED AS A SUPPLY PIN OR INPUT. ** PIN 1 INDICATION DOT The CBT3245A device is organized as one 8-bit switch. When enable (OE) is LOW, the switch is on and port A is connected to port B. When OE is HIGH, the switch is open and a high-impedance state exists between the two ports. Figure 2. Pin configuration — DHVQFN (top view) PIN DESCRIPTION The CBT3245A is characterized for operation from -40 to +85 °C. PIN NUMBER SYMBOL 1 NC No internal connection 19 OE Output enable input 2, 3, 4, 5, 6, 7, 8, 9 A1-A8 Inputs 18, 17, 16, 15, 14, 13, 12, 11 B1-B8 Outputs 10 GND Ground (0V) 20 VCC Positive supply voltage PIN CONFIGURATION — SO, SSOP, QSOP, AND TSSOP NC 1 20 VCC A1 2 19 OE A2 3 18 B1 A3 4 17 B2 A4 5 16 B3 A5 6 15 B4 A6 7 14 B5 A7 8 13 B6 A8 9 12 B7 11 B8 GND 10 SA00649 NAME AND FUNCTION SA00507 Figure 1. Pin configuration — SO, SSOP, QSOP, and TSSOP ORDERING INFORMATION PACKAGES TEMPERATURE RANGE ORDER CODE TOPSIDE MARK DWG NUMBER 20-Pin Plastic DHVQFN -40 to 85 °C CBT3245ABQ CT3245A SOT764-1 20-Pin Plastic TSSOP -40 to 85 °C CBT3245APW CT3245A SOT360-1 20-Pin Plastic SSOP (QSOP) -40 to 85 °C CBT3245ADS CT3245ADS SOT724-1 20-Pin Plastic SSOP -40 to 85 °C CBT3245ADB CT3245A SOT339-1 20-Pin Plastic SO -40 to 85 °C CBT3245AD CBT3245AD SOT163-1 Standard packing quantities and other packaging data is available at www.philipslogic.com/packaging. 2003 Jun 27 2 Philips Semiconductors Product data Octal bus switch CBT3245A LOGIC SYMBOL A1 A8 OE FUNCTION TABLE 2 18 9 INPUT INPUTS/OUTPUTS OE A, B L A=B H Z B1 11 B8 H = HIGH voltage level L = LOW voltage level Z = HIGH impedance “off” state 19 SA00508 ABSOLUTE MAXIMUM RATINGS1, 2 SYMBOL VCC IIK PARAMETER CONDITIONS RATING UNIT -0.5 to +7.0 V -50 mA -0.5 to +7.0 V VO < 0 -50 mA DC supply voltage DC input diode current VI < 0 voltage3 VI DC input IOK DC output diode current VOUT DC output voltage3 output in Off or HIGH state -0.5 to +7 V IOUT DC output current output in LOW state 128 mA Tstg Storage temperature range -65 to 150 °C NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150 °C. 3. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER UNIT MIN MAX VCC DC supply voltage 4.0 5.5 V VIH HIGH-level input voltage 2.0 — V VIL LOW-level input voltage — 0.8 V -40 +85 °C Tamb 2003 Jun 27 Operating free-air temperature range 3 Philips Semiconductors Product data Octal bus switch CBT3245A DC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL VIK II ICC ∆ICC CI CIO(OFF) ron3 PARAMETER Tamb = -40 to +85 °C TEST CONDITIONS UNIT MIN TYP1 MAX Input clamp voltage VCC = 4.5 V; II = -18 mA — — -1.2 V Input leakage current VCC = 5.5 V; VI = GND or 5.5 V — — ±5 µA Quiescent supply current VCC = 5.5 V; IO = 0, VI = VCC or GND — 1 3 µA Additional supply current per input pin2 VCC = 5.5 V, one input at 3.4 V, other inputs at VCC or GND — — 3.5 mA Control pins VI= 3 V or 0, OE = VCC — 3.2 — pF Pin capacitance (OFF state) VO = 3 V or 0 — 6.6 — pF VCC = 4.5 V; V1 = 0 V; II = 64 mA — 5 7 VCC = 4.5 V; V1 = 0 V; II = 30 mA — 5 7 VCC = 4.5 V; V1 = 2.4 V; II = 15 mA — 10 15 On-resistance Ω NOTES: 1. All typical values are at VCC = 5 V, Tamb = 25 °C 2. This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND 3. Measured by the voltage drop between the A and the B terminals at the indicated current through the switch. On-state resistance is determined by the lowest voltage of the two (A or B) terminals. AC CHARACTERISTICS GND = 0 V; tR; CL = 50 pF CBT3245A SYMBOL PARAMETER tpd Propagation ten tdis delay1 FROM (INPUT) TO (OUTPUT) Tamb = -40 to +85 °C VCC = +5.0 V ±0.5 V MIN MAX UNIT A or B B or A — 0.25 ns Output enable time to HIGH and LOW level OE A or B 1.0 5.9 ns Output disable time from HIGH and LOW level OE A or B 1.0 6.0 ns NOTES: 1. This parameter is warranted but not production tested. The propagation delay is based on the RC time constant of the typical on-state resistance of the switch and a load capacitance of 50 pF, when driven by an ideal voltage source (zero output impedance). 2003 Jun 27 4 Philips Semiconductors Product data Octal bus switch CBT3245A AC WAVEFORMS VM = 1.5 V, VIN = GND to 3.0 V 3V 3V 1.5 V Output Control (Low-level enabling ) 1.5 V INPUT 1.5 V 1.5 V 0V tPLH 0V tPLZ tPZL tPHL 3.5 V Output Waveform 1 S1 at 7 V (see Note) VOH 1.5 V 1.5 V OUTPUT 1.5 V Output Waveform 2 S1 at Open (see Note) SA00028 Waveform 1. Input to Output Propagation Delays VOL tPHZ tPZH VOL VOL + 0.3 V VOH VOH - 0.3 V 1.5 V 0V Note: Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. SA00029 Waveform 2. 3-State Output Enable and Disable Times TEST CIRCUIT AND WAVEFORMS 7V 500 Ω From Output Under Test S1 Open GND 500 Ω CL = 50 pF Load Circuit TEST S1 tpd open tPLZ/tPZL 7V tPHZ/tPZH open DEFINITIONS CL = Load capacitance includes jig and probe capacitance; see AC CHARACTERISTICS for value. SA00012 NOTES: 1. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. 2. The outputs are measured one at a time with one transition per measurement. 2003 Jun 27 5 Philips Semiconductors Product data Octal bus switch CBT3245A DHVQFN20: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 20 terminals; body 2.5 x 4.5 x 0.85 mm 2003 Jun 27 6 SOT764-1 Philips Semiconductors Product data Octal bus switch CBT3245A TSSOP20: plastic thin shrink small outline package; 20 leads; body width 4.4 mm 2003 Jun 27 7 SOT360-1 Philips Semiconductors Product data Octal bus switch CBT3245A SSOP20: plastic shrink small outline package; 20 leads; body width 3.9 mm; lead pitch 0.635 mm 2003 Jun 27 8 SOT724-1 Philips Semiconductors Product data Octal bus switch CBT3245A SSOP20: plastic shrink small outline package; 20 leads; body width 5.3 mm 2003 Jun 27 9 SOT339-1 Philips Semiconductors Product data Octal bus switch CBT3245A SO20: plastic small outline package; 20 leads; body width 7.5 mm 2003 Jun 27 10 SOT163-1 Philips Semiconductors Product data Octal bus switch REVISION HISTORY Rev Date CBT3245A Description _2 20030627 Product data (9397 750 11679); ECN 853-2313 30017 dated 11 Jun 2003. Supersedes data of 2002 Feb 18 (9397 750 09462). Modifications: • Addition of QSOP and DHVQFN package types. _1 20020218 Product data (9397 750 09462); ECN 853-2313 27745 of 18 Feb 2002. 2003 Jun 27 11 Philips Semiconductors Product data Octal bus switch CBT3245A Data sheet status Level Data sheet status[1] Product status[2] [3] Definitions I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes in the products—including circuits, standard cells, and/or software—described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Koninklijke Philips Electronics N.V. 2003 All rights reserved. Printed in U.S.A. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Date of release: 06-03 For sales offices addresses send e-mail to: [email protected]. Document order number: Philips Semiconductors 2003 Jun 27 12 9397 750 11679