SL Power CENB1030A4803F01 Ite switch-mode power supply Datasheet

CENB1030
Universal 30 Watt Series
ITE Switch-Mode Power Supply
3 Year Warranty
•100-240VAC Universal Input
•Meets EISA2007, CEC Efficiency Level V,
EU (EC) No 278/2009 Phase II
nd
•Certified to UL/EN60950-1, 2
Edition
•5Vto 48V outputs, up to 32W
•Modified and Custom Designs Available
•Regulated Output with Low Ripple
•Impact-Resistant Polycarbonate Enclosure
•No load Power Consumption <0.3W
•Limited Power Source
•Desktop & Wall Plug Styles
RoHS
All Specifications are typical at nominal input, full load at 25°C unless otherwise stated.
Specifications
AC Input
Input Current
100-240VAC, -/-10%, 47-63 Hz, 1∅
100VAC: 0.9A
Inrush Current
Input Fuse
Efficiency
Output Voltage
60A peak, 264Vac, cold start
3.15A Internal Primary Current Fuse is provided
Meets EISA2007, CEC Efficiency Level V,
and EU(EC) No. 278/2009 Phase II requirements
See chart
Output Power
See chart
Ripple and Noise
1% pk-pk max., 20MHz BW
Line & Load Voltage Regulation
Transient Response
LPS
Line: +/- 1%, Load: +/-5%
500μs max., 50% load step, typical
Minimum Load
Not required
Case Material:
Black 94V0 Polycarbonate
Case Dimensions:
Output Connector:
95 x 54 x 31mm. See outline drawing
Weight = 200g
2.5mm barrel type (Ault #3) connector,
center contact (+). Other options available
MTBF
>100,000 hours calculated
Hold-up Time
18 ms min. @ 115VAC, 60 msec @ 230VAC
Turn-on Time
2 seconds, max.
Topology
Switching – Fixed Frequency Flyback
Overload Protection
Hiccup Mode
Short Circuit Protection
Hiccup Mode
EMC
See chart below
Safety Standards
Dielectric Withstand
Operating Temperature
Storage Temperature
Relative Humidity
EN/IEC/CSA/UL60950-1, 2nd Edition, LPS
Input-Output: 4,242VDC, Input-GND: 1,500 Vac,
Output-GND: 500Vdc
0° to 40°C, no derating
-40° to +85°C
5% to 95%, non-condensing
Altitude
Output Cable:
0 to 10,000 ft
5V – 9V models: #18AWG (SPT-1), 1,500mm, 2 conductor
12V – 48V models: #18AWG (UL1185), 1,500mm, 2 conductor
EMC Specifications
Conducted Emissions
Radiated Emissions
Line Frequency Harmonics
Voltage Fluctuations/Flicker
Static Discharge Immunity
Radiated RF Immunity
EFT/Burst Immunity
Line Surge Immunity
Conducted RF Immunity
Power Frequency Magnetic Field Immunity
Voltage Dip Immunity
EN55022 Class B, FCC Part 15, Class B.
EN55022 Class B, FCC Part 15, Class B.
EN61000-3-2, Class A
EN61000-3-3
EN61000-4-2, 6kV Contact Discharge, 8kV air discharge
EN61000-4-3, 3V/m.
EN61000-4-4, 2kV/5kHz.
EN61000-4-5, 1kV differential, 2kV common-mode
EN61000-4-6, 3Vrms
EN61000-4-8, 3A/m
EN61000-4-11, Criteria B
______________________________________________________________________________________________________________________________
SL Power Electronics Corp • 6050 King Drive Ventura, CA 93003 • Phone 805.486.4565 • Fax 858.712.2040 • Email: [email protected] • www.slpower.com
1 of 2
CENB1030
Universal 30 Watt Series
ITE Switch Mode Power Supply
3 Year Warranty
Model Number
Volts (V)
Output Current (max)
Max Watts
Ripple (Vp-p max)
CENB1030A0503F01
CENB1030A0703F01
CENB1030A0903F01
CENB1030A1203F01
CENB1030A1403F01
CENB1030A1503F01
CENB1030A1803F01
CENB1030A2403F01
CENB1030A4803F01
5V
7.5 V
9V
12 V
14 V
15 V
18 V
24 V
48 V
4.00 A
3.00 A
3.00 A
2.50 A
2.10 A
2.00 A
1.67 A
1.33 A
0.67 A
20.0 W
22.5 W
27.0 W
30.0 W
29.4 W
30.0 W
30.0 W
31.9 W
32.1 W
50 mV
75 mV
90 mV
120 mV
140 mV
150 mV
180 mV
240 mV
480 mV
Notes: Part numbers above include #3 output connector and IEC320 C14 grounded input receptacle. See below for other options.
Model Number Key
CENB 1 030 A VV 03 F 01
Model
Input Connector:
Output Connector:
Output Voltage:
Model
Output Pow er:
# of Outputs
Product Fam ily:
"01" = Standard. "02" and higher indicates a m odified m odel.
"F" = IEC320 C14 grounded, Other options available, see below
"03" = 2.5m m Barrel Type Connector. Other options available, contact factory.
"05" = 5Vdc, "12" = 12Vdc, "24" = 24Vdc, etc.
"A" = Original Configuration
"030" = 30 Watts
"1" = Single Output
"C" = Comm ercial/ITE/Industrial, "E" = External, "NB" = Model Series Designator
AC Input Receptacle Options
Desktop
IEC320 - C14
Class I
Grounded
IEC320 - C18
Class II
Ungro unde d
IEC320 - C8
Class II
"Shaver"
(F)
(Q)
(N)
Notes:
Output Connector
Wall-Plug
N. Am erica
Japan
N. Am erica
Japan
Int erc ha ngable
Fixed
(C)
(B)
Europe
Australia
Fixed
United
Kingdom
Fixed
(M)
(G)
(H)
Fixed
1. For desktop options, choose applicable letter above.
Notes:
2. For Wall-Plug options, choose the applicable letter above and the unit w ill be fitted w ith
the receptacle chosen. The N. A. blade version (C) w ill be an interchangeable blade.
The other options (B), (M), (G), and (H) w ill be fixed blades m olded in the case.
3. Blade Kit is available w hich w ill include one each of a EU, UK, and Australian blade. Kit part #
is KT1027K. These can be used w ith the (C) version, to allow blades to be changed.
1. Ault #3 Connector, center contact (+).
2. Connector is Sw itchcraft 760 plug or equivalent.
Mating connector is Sw itchcraft 712A or equivalent.
3. Other connector options are available. Contact your local
SL Pow er Representative for details.
Outline Drawings
DATE
CODE
Desktop Style
Wall-plug Style “C” Option Shown (with KT1027K interchangeable blade kit)
Data Sheet © 2014 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication.
Rev. 9-22-14
However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice.
______________________________________________________________________________________________________________________________ 2 of 2
SL Power Electronics Corp • 6050 King Drive Ventura, CA 93003 • Phone 805.486.4565 • Fax 858.712.2040 • Email: [email protected] • www.slpower.com
Similar pages