Elpida HM51W16405LS-5 16 m edo dram (4-mword â´ 4-bit) 4 k refresh/2 k refresh Datasheet

16 M EDO DRAM (4-Mword × 4-bit)
4 k Refresh/2 k Refresh
LP
EO
Description
HM51W16405 Series
HM51W17405 Series
E0152H10 (Ver. 1.0)
(Previous ADE-203-647D (Z))
Jul. 6, 2001 (K)
The HM51W16405 Series, HM51W17405 Series are CMOS dynamic RAMs organized 4,194,304-word ×
4-bit. They employ the most advanced CMOS technology for high performance and low power. The
HM51W16405 Series, HM51W17405 Series offer Extended Data Out (EDO) Page Mode as a high speed
access mode.They have package variations of standard 300-mil 26-pin plastic SOJ and 300-mil 26-pin
plastic TSOP.
ro
Features
ct
du
• Single 3.3 V (±0.3 V)
• Access time: 50 ns/60 ns/70 ns (max)
• Power dissipation
 Active mode : 324 mW /288 mW /252 mW (max) (HM51W16405 Series)
: 360mW/324 mW/288 mW (max) (HM51W17405 Series)
 Standby mode : 7.2 mW (max)
: 0.36 mW (max) (L-version)
• EDO page mode capability
• Long refresh period
 4096 refresh cycles : 64 ms (HM51W16405 Series)
: 128 ms (L-version)
 2048 refresh cycles : 32 ms (HM51W17405 Series)
: 128 ms (L-version)
• 4 variations of refresh
 RAS-only refresh
 CAS-before-RAS refresh
 Hidden refresh
 Self refresh (L-version)
Elpida Memory, Inc. is a joint venture DRAM company of NEC Corporation and Hitachi, Ltd.
EO
HM51W16405 Series, HM51W17405 Series
• Battery backup operation (L-version)
• Test function
 16-bit parallel test mode
Ordering Information
Access time
Package
HM51W16405S-5
HM51W16405S-6
HM51W16405S-7
50 ns
60 ns
70 ns
300-mil 26-pin plastic SOJ
(CP-26/24DB)
HM51W16405LS-5
HM51W16405LS-6
HM51W16405LS-7
HM51W17405S-5
HM51W17405S-6
HM51W17405S-7
HM51W17405LS-5
HM51W17405LS-6
HM51W17405LS-7
50 ns
60 ns
70 ns
50 ns
60 ns
70 ns
50 ns
60 ns
70 ns
50 ns
60 ns
70 ns
300-mil 26-pin plastic TSOP II
(TTP-26/24DA)
HM51W16405LTS-5
HM51W16405LTS-6
HM51W16405LTS-7
50 ns
60 ns
70 ns
HM51W17405TS-5
HM51W17405TS-6
HM51W17405TS-7
50 ns
60 ns
70 ns
HM51W17405LTS-5
HM51W17405LTS-6
HM51W17405LTS-7
50 ns
60 ns
70 ns
ct
du
ro
HM51W16405TS-5
HM51W16405TS-6
HM51W16405TS-7
LP
Type No.
Data Sheet E0152H10
2
EO
HM51W16405 Series, HM51W17405 Series
Pin Arrangement
HM51W16405S/LS Series
HM51W16405TS/LTS Series
1
26
VSS
VCC
1
26
VSS
I/O1
2
25
I/O4
I/O1
2
25
I/O4
I/O2
3
24
I/O3
I/O2
3
24
I/O3
WE
4
23
CAS
WE
RAS
A11
A10
A0
A1
A2
VCC
4
23
CAS
5
22
OE
RAS
5
22
OE
6
21
A9
A11
6
21
A9
8
19
A8
A10
8
19
A8
9
18
A7
A0
9
18
A7
10
17
A6
A1
10
17
A6
11
16
A5
A2
11
16
A5
12
15
A4
A3
12
15
A4
13
14
VSS
13
14
VSS
(Top view)
Pin Description
Function
A0 to A11
Address input
— Row/Refresh address A0 to A11
— Column address
A0 to A9
I/O1 to I/O4
Data input/Data output
RAS
Row address strobe
CAS
Column address strobe
WE
Read/Write enable
OE
Output enable
VCC
Power supply
VSS
Ground
(Top view)
ct
Pin name
VCC
du
ro
A3
LP
VCC
Data Sheet E0152H10
3
EO
HM51W16405 Series, HM51W17405 Series
Pin Arrangement
HM51W17405S/LS Series
VCC
HM51W17405TS/LTS Series
1
26
VSS
I/O1
2
25
I/O4
I/O3
I/O2
3
24
I/O3
WE
4
23
CAS
1
26
VSS
I/O1
2
25
I/O4
I/O2
3
24
RAS
NC
A10
A0
A1
A2
VCC
23
CAS
5
22
OE
RAS
5
22
OE
6
21
A9
NC
6
21
A9
8
19
A8
A10
8
19
A8
9
18
A7
A0
9
18
A7
10
17
A6
A1
10
17
A6
11
16
A5
A2
11
16
A5
12
15
A4
A3
12
15
A4
13
14
VSS
13
14
VSS
ro
A3
4
LP
WE
VCC
(Top view)
Pin Description
A0 to A10
Address input
— Row/Refresh address A0 to A10
— Column address
A0 to A10
I/O1 to I/O4
Data input/Data output
RAS
Row address strobe
CAS
Column address strobe
WE
Read/Write enable
OE
Output enable
VCC
Power supply
VSS
Ground
NC
No connection
ct
Function
Data Sheet E0152H10
4
(Top view)
du
Pin name
VCC
EO
HM51W16405 Series, HM51W17405 Series
Block Diagram(HM51W16405 Series)
A1
•
•
•
address
Column decoder
4M array
buffers
Row
buffers
4M array
I/O buffers
4M array
I/O1
to
I/O4
ro
address
A11
OE
Column
•
•
•
A9
A10
WE
Timing and control
Row decoder
to
CAS
LP
A0
RAS
4M array
ct
du
Data Sheet E0152H10
5
EO
HM51W16405 Series, HM51W17405 Series
Block Diagram(HM51W17405 Series)
A1
WE
OE
Timing and control
Column decoder
Column
•
•
•
A10
•
•
•
address
4M array
buffers
Row
buffers
4M array
I/O buffers
4M array
ro
address
Row decoder
to
CAS
LP
A0
RAS
4M array
ct
du
Data Sheet E0152H10
6
I/O1
to
I/O4
EO
HM51W16405 Series, HM51W17405 Series
Absolute Maximum Ratings
Symbol
Value
Unit
Voltage on any pin relative to V SS
VT
–0.5 to VCC + 0.5 (≤ +4.6 V (max))
V
Supply voltage relative to VSS
VCC
–0.5 to +4.6
V
Short circuit output current
Iout
50
mA
Power dissipation
PT
1.0
W
Operating temperature
Topr
0 to +70
°C
–55 to +125
°C
LP
Parameter
Storage temperature
Tstg
Recommended DC Operating Conditions (Ta = 0 to +70˚C)
Parameter
Supply voltage
Input high voltage
Input low voltage
Note:
Symbol
Min
Typ
Max
Unit
Notes
VCC
3.0
3.3
3.6
V
1, 2
VIH
2.0
—
VCC + 0.3
V
1
VIL
–0.3
—
0.8
V
1
1. All voltage referred to VSS .
ct
du
ro
Data Sheet E0152H10
7
EO
HM51W16405 Series, HM51W17405 Series
DC Characteristics
(Ta = 0 to +70˚C, VCC = 3.3 V ± 0.3 V, VSS = 0 V) (HM51W16405 Series)
HM51W16405
-5
-7
Min Max Min Max Min Max Unit
Test conditions
I CC1
—
90
—
80
—
70
mA
t RC = min
Standby current
I CC2
—
2
—
2
—
2
mA
TTL interface
RAS, CAS = VIH
Dout = High-Z
—
1
—
1
—
1
mA
CMOS interface
RAS, CAS ≥ VCC – 0.2 V
Dout = High-Z
Standby current
(L-version)
I CC2
—
100 —
100 —
100 µA
CMOS interface
RAS, CAS ≥ VCC – 0.2 V
Dout = High-Z
I CC3
—
90
—
80
—
70
mA
t RC = min
I CC5
—
5
—
5
—
5
mA
RAS = VIH
CAS = VIL
Dout = enable
I CC6
—
EDO page mode current*1, * 3 I CC7
—
Battery backup current
I CC10
—
Self refresh mode current
(L-version)
I CC11
—
Input leakage current
I LI
–10 10
–10 10
–10 10
µA
0 V ≤ Vin ≤ 4.6 V
Output leakage current
I LO
–10 10
–10 10
–10 10
µA
0 V ≤ Vin ≤ 4.6 V
Dout = disable
Output high voltage
VOH
2.4
VCC 2.4
VCC 2.4
VCC
V
High Iout = –2 mA
Output low voltage
VOL
0
0.4
0.4
0.4
V
Low Iout = 2 mA
Operating current* , *
1
2
RAS-only refresh current*2
1
Standby current*
CAS-before-RAS refresh
current
ro
Symbol
LP
Parameter
-6
90
—
80
—
70
mA
t RC = min
80
—
70
—
65
mA
t HPC = min
300 —
300 µA
CMOS interface
Dout = High-Z, CBR
refresh: tRC = 31.3 µs
t RAS ≤ 0.3 µs
200 —
200 —
200 µA
CMOS interface
RAS, CAS ≤ 0.2 V
Dout = High-Z
0
du
300 —
0
ct
Notes : 1. I CC depends on output load condition when the device is selected. ICC max is specified at the
output open condition.
2. Address can be changed once or less while RAS = VIL.
3. Address can be changed once or less while CAS = VIH.
Data Sheet E0152H10
8
EO
HM51W16405 Series, HM51W17405 Series
DC Characteristics
(Ta = 0 to +70˚C, VCC = 3.3 V ± 0.3 V, VSS = 0 V) (HM51W17405 Series)
Parameter
HM51W17405
-5
-6
-7
Symbol
Min Max Min Max Min Max Unit
Test conditions
Operating current* , * 2
I CC1
—
100 —
90
—
80
mA
t RC = min
Standby current
I CC2
—
2
—
2
—
2
mA
TTL interface
RAS, CAS = VIH
Dout = High-Z
—
1
—
1
—
1
mA
CMOS interface
RAS, CAS ≥ VCC – 0.2 V
Dout = High-Z
I CC2
—
100 —
100 —
100 µA
CMOS interface
RAS, CAS ≥ VCC – 0.2 V
Dout = High-Z
I CC3
—
100 —
90
—
80
mA
t RC = min
I CC5
—
5
5
—
5
mA
RAS = VIH
CAS = VIL
Dout = enable
I CC6
—
100 —
90
—
80
mA
t RC = min
EDO page mode current*1, * 3 I CC7
—
90
80
—
75
mA
t HPC = min
Battery backup current
I CC10
—
Self refresh mode current
(L-version)
I CC11
—
Input leakage current
I LI
–10 10
–10 10
–10 10
µA
0 V ≤ Vin ≤ 4.6 V
Output leakage current
I LO
–10 10
–10 10
–10 10
µA
0 V ≤ Vin ≤ 4.6 V
Dout = disable
Output high voltage
VOH
2.4
VCC 2.4
VCC 2.4
VCC
V
High Iout = –2 mA
Output low voltage
VOL
0
0.4
0.4
0.4
V
Low Iout = 2 mA
1
RAS-only refresh current*2
1
Standby current*
CAS-before-RAS refresh
current
—
ro
LP
Standby current
(L-version)
—
300 —
300 µA
CMOS interface
Dout = High-Z, CBR
refresh: tRC = 62.5 µs
t RAS ≤ 0.3 µs
200 —
200 —
200 µA
CMOS interface
RAS, CAS ≤ 0.2 V
Dout = High-Z
0
du
300 —
0
ct
Notes : 1. I CC depends on output load condition when the device is selected. ICC max is specified at the
output open condition.
2. Address can be changed once or less while RAS = VIL.
3. Address can be changed once or less while CAS = VIH.
Data Sheet E0152H10
9
EO
HM51W16405 Series, HM51W17405 Series
Capacitance (Ta = 25˚C, VCC = 3.3 V ± 0.3 V)
Parameter
Symbol
Typ
Max
Unit
Notes
Input capacitance (Address)
CI1
—
5
pF
1
Input capacitance (Clocks)
CI2
—
7
pF
1
Output capacitance (Data-in, Data-out)
CI/O
—
7
pF
1, 2
Notes : 1. Capacitance measured with Boonton Meter or effective capacitance measuring method.
2. CAS = VIH to disable Dout.
ct
du
ro
LP
Data Sheet E0152H10
10
EO
HM51W16405 Series, HM51W17405 Series
AC Characteristics (Ta = 0 to +70˚C, VCC = 3.3 V ± 0.3 V, VSS = 0 V) *1, *2, *18
Test Conditions
Input rise and fall time: 2 ns
Input levels: VIL = 0 V, V IH = 3 V
Input timing reference levels: 0.8 V, 2.0 V
Output timing reference levels: 0.8 V, 2.0 V
Output load: 1 TTL gate + C L (100 pF) (Including scope and jig)
LP
•
•
•
•
•
Read, Write, Read-Modify-Write and Refresh Cycles (Common parameters)
Parameter
HM51W16405/HM51W17405
-5
-6
-7
Min
Max
Min
Max
Min
Max
Unit
Random read or write cycle time
t RC
84
—
104
—
124
—
ns
RAS precharge time
t RP
30
—
40
—
50
—
ns
CAS precharge time
t CP
8
—
10
—
13
—
ns
RAS pulse width
t RAS
50
10000 60
10000 70
10000 ns
8
10000 10
10000 13
10000 ns
0
—
0
—
0
—
ns
8
—
10
—
10
—
ns
0
—
0
—
0
—
ns
8
—
10
—
13
—
ns
12
37
14
45
14
52
ns
3
12
30
12
35
ns
4
13
—
13
—
ns
40
—
45
—
ns
5
—
5
—
ns
15
—
18
—
ns
5
0
—
0
—
ns
6
0
—
0
—
ns
6
2
50
2
t CAS
Row address setup time
t ASR
Row address hold time
t RAH
Column address setup time
t ASC
Column address hold time
t CAH
RAS to CAS delay time
t RCD
RAS to column address delay time
t RAD
10
25
RAS hold time
t RSH
10
—
CAS hold time
t CSH
35
—
CAS to RAS precharge time
t CRP
5
—
OE to Din delay time
t OED
13
—
OE delay time from Din
t DZO
0
—
CAS delay time from Din
t DZC
0
—
Transition time (rise and fall)
tT
2
50
ct
CAS pulse width
du
ro
Symbol
50
ns
Notes
7
Data Sheet E0152H10
11
EO
HM51W16405 Series, HM51W17405 Series
Read Cycle
HM51W16405/HM51W17405
-5
-6
-7
Symbol
Min
Max
Min
Max
Min
Max
Unit
Notes
Access time from RAS
t RAC
—
50
—
60
—
70
ns
8, 9, 20
Access time from CAS
t CAC
—
13
—
15
—
18
ns
9, 10, 17,
20
Access time from address
t AA
—
25
—
30
—
35
ns
9, 11, 17,
20
Access time from OE
t OEA
—
13
—
15
—
18
ns
9, 20
Read command setup time
t RCS
0
—
0
—
0
—
ns
Read command hold time to CAS
t RCH
0
—
0
—
0
—
ns
Read command hold time from
RAS
t RCHR
50
—
60
—
70
—
ns
Read command hold time to RAS
t RRH
0
—
0
—
0
—
ns
Column address to RAS lead time
t RAL
25
—
30
—
35
—
ns
Column address to CAS lead time
t CAL
15
—
18
—
23
—
ns
CAS to output in low-Z
t CLZ
0
—
0
—
0
—
ns
Output data hold time
t OH
3
—
3
—
3
—
ns
Output data hold time from OE
t OHO
3
—
3
—
3
—
ns
Output buffer turn-off time
t OFF
—
13
—
15
—
15
ns
13, 22
Output buffer turn-off to OE
t OEZ
—
13
—
15
—
15
ns
13
CAS to Din delay time
t CDD
13
—
15
—
18
—
ns
5
Output data hold time from RAS
t OHR
3
—
3
—
3
—
ns
22
Output buffer turn-off to RAS
t OFR
—
13
22
Output buffer turn-off to WE
t WEZ
—
13
WE to Din delay time
t WED
13
—
RAS to Din delay time
t RDD
13
—
RAS next CAS delay time
t RNCD
50
—
du
ro
LP
Parameter
—
15
—
15
ns
—
15
—
15
ns
15
—
18
—
ns
15
—
18
—
ns
60
—
70
—
ns
ct
Data Sheet E0152H10
12
12
12
22
EO
HM51W16405 Series, HM51W17405 Series
Write Cycle
HM51W16405/HM51W17405
-5
-6
-7
Symbol
Min
Max
Min
Max
Min
Max
Unit
Notes
Write command setup time
t WCS
0
—
0
—
0
—
ns
14
Write command hold time
t WCH
8
—
10
—
13
—
ns
Write command pulse width
t WP
8
—
10
—
10
—
ns
Write command to RAS lead time
t RWL
8
—
10
—
13
—
ns
Write command to CAS lead time
t CWL
8
—
10
—
13
—
ns
Data-in setup time
t DS
0
—
0
—
0
—
ns
15
t DH
8
—
10
—
13
—
ns
15
Notes
Data-in hold time
LP
Parameter
Read-Modify-Write Cycle
-5
-6
-7
Symbol
Min
Max
Min
Max
Min
Max
Unit
Read-modify-write cycle time
t RWC
111
—
135
—
161
—
ns
RAS to WE delay time
t RWD
67
—
79
—
92
—
ns
14
CAS to WE delay time
t CWD
30
—
34
—
40
—
ns
14
Column address to WE delay time
t AWD
42
—
49
—
57
—
ns
14
OE hold time from WE
t OEH
13
—
15
—
18
—
ns
Refresh Cycle
du
ro
Parameter
HM51W16405/HM51W17405
HM51W16405/HM51W17405
-5
Parameter
Symbol
-6
-7
Max
Min
Max
Min
Max
Unit
CAS setup time (CBR refresh cycle) t CSR
5
—
5
—
5
—
ns
CAS hold time (CBR refresh cycle) t CHR
8
—
10
—
10
—
ns
WE setup time (CBR refresh cycle) t WRP
0
—
0
—
0
—
ns
WE hold time (CBR refresh cycle)
t WRH
8
—
10
—
10
—
ns
RAS precharge to CAS hold time
t RPC
5
—
5
—
5
—
ns
Notes
ct
Min
Data Sheet E0152H10
13
EO
HM51W16405 Series, HM51W17405 Series
EDO Page Mode Cycle
HM51W16405/HM51W17405
-5
-6
-7
Symbol
Min Max
Min Max
Min Max
Unit
Notes
EDO page mode cycle time
t HPC
20
—
25
30
ns
21
EDO page mode RAS pulse width
t RASP
—
100000 —
100000 —
100000 ns
16
Access time from CAS precharge
t CPA
—
30
—
35
—
40
ns
9, 17, 20
RAS hold time from CAS precharge t CPRH
30
—
35
—
40
—
ns
Output data hold time from CAS low t DOH
3
—
3
—
3
—
ns
CAS hold time referred OE
t COL
8
—
10
—
13
—
ns
CAS to OE setup time
t COP
5
—
5
—
5
—
ns
Read command hold time from
CAS precharge
t RCHC
30
—
35
—
40
—
ns
LP
Parameter
—
—
9, 17
EDO Page Mode Read-Modify-Write Cycle
HM51W16405/HM51W17405
ro
-5
Parameter
Symbol
EDO page mode read- modify-write t HPRWC
cycle time
WE delay time from CAS precharge t CPW
-6
-7
Max
Min
Max
Min
57
—
68
—
79
ns
45
—
54
—
62
ns
14
Notes
Test Mode Cycle *19
du
Min
Max
Unit
Notes
HM51W16405/HM51W17405
-5
-6
-7
Parameter
Symbol
Min
Max
Min
Max
Min
Max
Unit
Test mode WE setup time
t WTS
0
—
0
—
0
—
ns
Test mode WE hold time
t WTH
8
—
10
—
10
—
ns
Parameter
Symbol
Max
Refresh period
t REF
64
Refresh period (L-version)
t REF
128
Data Sheet E0152H10
14
ct
Refresh (HM51W16405 Series)
Unit
Notes
ms
4096 cycles
ms
4096 cycles
EO
HM51W16405 Series, HM51W17405 Series
Refresh (HM51W17405 Series)
Parameter
Symbol
Max
Unit
Notes
Refresh period
t REF
32
ms
2048 cycles
Refresh period (L-version)
t REF
128
ms
2048 cycles
Self Refresh Mode (L-version)
LP
Parameter
HM51W16405L/HM51W17405L
-5
-6
-7
Symbol
Min
Max
Min
Max
Min
Max
Unit
RAS pulse width (self refresh)
t RASS
100
—
100
—
100
—
µs
RAS precharge time (self refresh)
t RPS
90
—
110
—
130
—
ns
CAS hold time (self refresh)
t CHS
–50
—
–50
—
–50
—
ns
Notes
ct
du
ro
Notes: 1. AC measurements assume t T = 2 ns.
2. An initial pause of 200 µs is required after power up followed by a minimum of eight initialization
cycles (any combination of cycles containing RAS-only refresh or CAS-before-RAS refresh). If
the internal refresh counter is used, a minimum of eight CAS-before-RAS refresh cycles are
required.
3. Operation with the tRCD (max) limit insures that tRAC (max) can be met, tRCD (max) is specified as a
reference point only; if t RCD is greater than the specified tRCD (max) limit, then access time is
controlled exclusively by tCAC .
4. Operation with the tRAD (max) limit insures that tRAC (max) can be met, tRAD (max) is specified as a
reference point only; if t RAD is greater than the specified tRAD (max) limit, then access time is
controlled exclusively by tAA .
5. Either t OED or tCDD must be satisfied.
6. Either t DZO or tDZC must be satisfied.
7. VIH (min) and VIL (max) are reference levels for measuring timing of input signals. Also, transition
times are measured between V IH (min) and VIL (max).
8. Assumes that t RCD ≤ tRCD (max) and tRAD ≤ tRAD (max). If tRCD or tRAD is greater than the maximum
recommended value shown in this table, t RAC exceeds the value shown.
9. Measured with a load circuit equivalent to 1 TTL loads and 100 pF.
10. Assumes that t RCD ≥ tRCD (max) and tRCD + tCAC (max) ≥ tRAD + tAA (max).
11. Assumes that t RAD ≥ tRAD (max) and tRCD + tCAC (max) ≤ tRAD + tAA (max).
12. Either t RCH or tRRH must be satisfied for a read cycles.
13. t OFF (max) and tOEZ (max) define the time at which the outputs achieve the open circuit condition
and are not referred to output voltage levels.
14. t WCS , t RWD, t CWD, t AWD and t CPW are not restrictive operating parameters. They are included in the
data sheet as electrical characteristics only; if t WCS ≥ tWCS (min), the cycle is an early write cycle
and the data out pin will remain open circuit (high impedance) throughout the entire cycle; if tRWD
≥ tRWD (min), tCWD ≥ tCWD (min), and tAWD ≥ tAWD (min), or tCWD ≥ tCWD (min), tAWD ≥ tAWD (min) and tCPW ≥
t CPW (min), the cycle is a read-modify-write and the data output will contain data read from the
selected cell; if neither of the above sets of conditions is satisfied, the condition of the data out
(at access time) is indeterminate.
Data Sheet E0152H10
15
EO
HM51W16405 Series, HM51W17405 Series
ct
du
ro
LP
15. These parameters are referred to CAS leading edge in early write cycles and to WE leading
edge in delayed write or read-modify-write cycles.
16. t RASP defines RAS pulse width in EDO page mode cycles.
17. Access time is determined by the longest among t AA , t CAC and t CPA.
18. In delayed write or read-modify-write cycles, OE must disable output buffer prior to applying data
to device.
19. The 16M DRAM offers a 16-bit time saving parallel test mode. Address CA0 and CA1 for the 4M
×4 are don’t care during test mode. Test mode is set by performing a WE-and-CAS-before-RAS
(WCBR) cycle. In 16-bit parallel test mode, data is written into 4 bits in parallel at each I/O (I/O1
to I/O4) and read out from each I/O.
If 4 bits of each I/O are equal (all 1s or 0s), data output pin is a high state during test mode read
cycle, then the device has passed. If they are not equal, data output pin is a low state, then the
device has failed.
Refresh during test mode operation can be performed by normal read cycles or by WCBR
refresh cycles.
To get out of test mode and enter a normal operation mode, perform either a regular CASbefore-RAS refresh cycle or RAS-only refresh cycle.
20. In a test mode read cycle, the value of tRAC , t AA , t CAC and t CPA is delayed by 2 ns to 5 ns for the
specified value. These parameters should be specified in test mode cycles by adding theabove
value to the specified value in this data sheet.
21. t HPC (min) can be achieved during a series of EDO page mode write cycles or EDO page mode
read cycles. If both write and read operation are mixed in a EDO page mode RAS cycle (EDO
page mode mix cycle (1), (2)), minimum value of CAS cycle (tCAS + tCP + 2 tT) becomes greater
than the specified t HPC (min) value. The value of CAS cycle time of mixed EDO page mode is
shown in EDO page mode mix cycle (1) and (2).
22. Data output turns off and becomes high impedance from later rising edge of RAS and CAS.
Hold time and turn off time are specified by the timing specifications of later rising edge of RAS
and CAS between t OHR and t OH , and between t OFR and t OFF.
23. Please do not use tRASS timing, 10 µs ≤ tRASS ≤ 100 µs. During this period, the device is in
transition state from normal operation mode to self refresh mode. If t RASS > 100 µs, then RAS
precharge time should use tRPS instead of tRP.
24. If you use distributed CBR refresh mode with 15.6 µs interval in normal read/write cycle, CBR
refresh should be executed within 15.6 µs immediately after exiting from and before entering
into self refresh mode.
25. If you use RAS only refresh or CBR burst refresh mode in normal read/write cycle, 4096 or 2048
cycles (4096 cycles: HM51W16405 Series, 2048 cycles: HM51W17405 Series) of distributed
CBR refresh with 15.6 µs interval should be executed within 64 or 32 ms (64 ms: HM51W16405
Series, 32 ms: HM51W17405 Series) immediately after exiting from and before entering into the
self refresh mode.
26. Repetitive self refresh mode without refreshing all memory is not allowed. Once you exit from
self fresh mode, all memory cells need to be refreshed before re-entering the self refresh mode
again.
27. XXX: H or L (H: VIH (min) ≤ VIN ≤ VIH (max), L: VIL (min) ≤ VIN ≤ VIL (max))
///////: Invalid Dout
When the address, clock and input pins are not described on timing waveforms, their pins must
be applied VIH or VIL.
Data Sheet E0152H10
16
EO
HM51W16405 Series, HM51W17405 Series
Timing Waveforms*27
Read Cycle
t RC
t RAS
t RP
RAS
LP
t CSH
t CRP
t RCD
t RSH
t CAS
tT
CAS
t RAD
t ASR
Address
t RAH
t ASC
t RAL
t CAL
t CAH
Column
Row
ro
t RRH
t RCHR
t RCS
WE
t DZC
t DZO
t OEA
OE
t RDD
t OED
t OEZ
t OHO
t OFF
t AA
ct
t CAC
t WED
t CDD
du
High-Z
Din
t RCH
t OH
t OFR
t OHR
t RAC
t CLZ
t WEZ
Dout
Dout
Data Sheet E0152H10
17
EO
HM51W16405 Series, HM51W17405 Series
Early Write Cycle
tRC
tRAS
tRP
RAS
tCSH
tCRP
LP
tRCD
tRSH
tCAS
tT
CAS
tASR
Address
tRAH
Row
tASC
tCAH
Column
ro
tWCS
WE
tWCH
Din
Din
High-Z*
ct
Dout
tDH
du
tDS
* t WCS
Data Sheet E0152H10
18
t WCS (min)
EO
HM51W16405 Series, HM51W17405 Series
Delayed Write Cycle*18
t RC
t RAS
t RP
RAS
t CSH
t CRP
LP
t RCD
t RSH
t CAS
tT
CAS
t ASR
Address
t RAH
t ASC
Row
t CAH
Column
t CWL
ro
t RCS
WE
t DZC
High-Z
Din
t DZO
t OEH
t OED
t OEZ
t CLZ
ct
OE
t DH
du
Din
t DS
t RWL
t WP
High-Z
Dout
Invalid Dout
Data Sheet E0152H10
19
EO
HM51W16405 Series, HM51W17405 Series
Read-Modify-Write Cycle *18
t RWC
t RAS
t RP
RAS
t RCD
LP
CAS
tT
t CAS
t CRP
t RAD
t ASR
Address
tRAH
t ASC
Row
WE
Column
t CWD
ro
t RCS
t CAH
tCWL
t AWD
t RWL
t RWD
t WP
t DZC
t DS
du
High-Z
Din
t DH
Din
t OED
t DZO
t OEH
t OEA
OE
t OEZ
t AA
t RAC
t OHO
Dout
Dout
t CLZ
Data Sheet E0152H10
20
ct
t CAC
High-Z
EO
HM51W16405 Series, HM51W17405 Series
RAS-Only Refresh Cycle
t RC
t RAS
t RP
RAS
t CRP
LP
CAS
tT
t ASR
Address
t RPC
t CRP
t RAH
Row
t OFR
t OFF
ct
du
!
High-Z
ro
Dout
Data Sheet E0152H10
21
EO
HM51W16405 Series, HM51W17405 Series
CAS-Before-RAS Refresh Cycle
t RC
t RP
t RAS
t RP
RAS
t RPC
t CSR
t CHR
t CRP
LP
,
t RPC
tT
CAS
t CP
WE
Address
Dout
t CP
t WRH
ro
t OFR
t OFF
t WRP
High-Z
ct
du
Data Sheet E0152H10
22
EO
HM51W16405 Series, HM51W17405 Series
Hidden Refresh Cycle
t RC
t RAS
t RC
t RAS
t RP
t RC
t RP
t RAS
t RP
RAS
tT
LP
t RSH
t CHR
t CRP
t RCD
CAS
t RAD
t ASR t RAH
Address
t RAL
t ASC
Row
t CAH
Column
t WRH
t WRP
ro
t RRH
tWRH
t RCS
t WRP
WE
t DZC
t RRH
t RCH
t DZO
t OEA
OE
t CAC
t AA
t CLZ
Dout
Dout
t CDD
t RDD
t OED
t OFF
t OH
t OEZ
t WEZ
t OHO
ct
t RAC
du
High-Z
Din
t WED
t OFR
t OHR
Data Sheet E0152H10
23
EO
HM51W16405 Series, HM51W17405 Series
EDO Page Mode Read Cycle
t RP
t RNCD
RAS
tT
t CSH
Address
Row
t HPC
t CPRH
t CP
t
tCAH
Column 1
tCAS
tCAS
t RCHC
t ASC t CAH
t ASC t CAH
Column 2
Column 3
t CAL
t CRP
RSH
t RCH t RCS
LP
tASR
tRAH tASC
t CP
t CAS
t RCHR
t RCS
WE
t HPC
t CP
t CAS
CAS
t HPC
t RASP
t CAL
t RRH
t RCH
t RAL
t CAH
tASC
t WED
Column 4
t CAL
t CAL
tRDD
tCDD
tDZC
Din
High-Z
tCOL
tCOP
tOED
ro
tDZO
OE
tCPA
tOEA
tAA
tCAC
tCAC
tAA
tWEZ
Dout
Dout 1
tAA
tOEZ
tOEA
Dout 2
tDOH
du
tRAC
tOEZ
tOHO
tOFR
tOHR
tOEZ
tCPA
tCPA
tAA
tCAC
Dout 2
tOHO
Dout 3
tCAC
tOHO
tOFF
tOH
tOEA
Dout 4
ct
Data Sheet E0152H10
24
EO
HM51W16405 Series, HM51W17405 Series
EDO Page Mode Early Write Cycle
tRP
tRASP
RAS
tT
tCSH
LP
CAS
tASR
Address
tHPC
tCAS
tRCD
Row
tRAH
tASC
tCAH
Column 1
tWCH
WE
Din
Dout
tDH
Din 1
tASC
tCAH
Column 2
tWCH
tWCS
tDS
tDH
tCP
tCAS
tASC
tCRP
tCAH
Column N
tWCS
tDS
tWCH
tDH
du
tDS
tRSH
tCAS
ro
tWCS
tCP
Din 2
Din N
High-Z*
ct
* t WCS
t WCS (min)
Data Sheet E0152H10
25
EO
HM51W16405 Series, HM51W17405 Series
EDO Page Mode Delayed Write Cycle *18
t RASP
t RP
RAS
tT
t CP
LP
t CSH
t RCD
CAS
t CRP
t CP
t HPC
t CAS
t CAS
t RSH
t CAS
t RAD
t ASR
t ASC
t RAH
Address
t ASC
t CAH
Row
t ASC
t CAH
Column 1
t CAH
Column 2
t CWL
WE
t WP
t DZC t DS
t CWL
t RCS
t WP
t WP
t DZC t DS
t DZC t DS
t DH
t DZO
t DH
Din
2
Din
N
t DZO
#
t DZO
t DH
du
Din
1
Din
t CWL
t RWL
t RCS
ro
t RCS
Column N
t OED
t OEH
t OEH
OE
t CLZ
t CLZ
t OEZ
t OEH
t CLZ
t OEZ
t OEZ
ct
High-Z
Dout
Invalid Dout
Invalid Dout
Data Sheet E0152H10
26
t OED
t OED
Invalid Dout
EO
HM51W16405 Series, HM51W17405 Series
EDO Page Mode Read-Modify-Write Cycle *18
t RASP
t RP
RAS
tT
t HPRWC
t RCD
CAS
t RSH
t CP
LP
t CP
t CAS
t CAS
t CRP
t CAS
t RAD
t ASR
Address
t ASC
t RAH
Row
t ASC
t CAH
t CAH
Column 1
t RWD
Column 2
t CWL
t WP
t
t DZC DS
t CWD
t RCS
t DZO
t OED
t DH
Din
N
t OED
t DZO
t OEH
t OEH
*#
t OEH
t DH
Din
2
t OED
t DZO
t RWL
t WP
t
t DZC DS
du
Din
1
t CWL
t CWD
t WP
t
t DZC DS
t DH
Din
t CPW
t AWD
ro
t RCS
t CWL
t AWD
t RCS
WE
Column N
t CPW
t AWD
t CWD
t ASC
t CAH
OE
t OHO
t OEA
t CAC
t OHO
t OEA
t CAC
t AA
t AA
t CPA
t RAC
t AA
t CPA
t OEZ
t CLZ
t CLZ
ct
t OEZ
t CLZ
t OHO
t OEA
t CAC
t OEZ
High-Z
Dout
Dout 1
Dout 2
Dout N
Data Sheet E0152H10
27
EO
HM51W16405 Series, HM51W17405 Series
EDO Page Mode Mix Cycle (1)
t RP
t RASP
RAS
tT
t CAS
CAS
t CRP
t CP
t CP
t CP
t CAS
tCAS
tCAS
LP
t CSH
tRSH
t RCD
t WCS
WE
t ASC
tRAH
tASR
Address
Row
t WCH
tCAH
Column 1
t CAL
t DS
tCPW
tAWD
t ASC t CAH
tASC t CAH
Column 2
Column 3
t CAL
tASC
t RAL
t CAH
Column 4
t CAL
t DH
Din 1
tWP
High-Z
tRDD
tCDD
t CAL
t DH
t DS
Din 3
ro
tOED
tWED
Din
t RRH
t RCH
t RCS
t RCS
OE
tCPA
tAA
tOEA
Dout
tAA
tAA
t OEZ
t DOH
tCAC t OHO
Dout 2
Dout 3
tOEZ
tCAC
du
tCAC
tOFR
tWEZ
tCPA
tCPA
tOHO
tOEA
tOFF
tOH
Dout 4
ct
Data Sheet E0152H10
28
EO
HM51W16405 Series, HM51W17405 Series
EDO Page Mode Mix Cycle (2)
t RNCD
t RP
t RASP
RAS
tT
t CAS
t RCD
t ASC
tRAH
tASR
Address
Row
tCAS
tCAS
t RCHR
t RCS
WE
t CAS
t CRP
t CP
t CP
LP
CAS
t CSH
t RCH tWCS t WCH
tCAH
Column 1
t ASC t CAH
Column 2
Column 3
t DS
t CAH
tASC
Column 4
t CAL
t DS
t DH
tRDD
tCDD
t DH
Din 2
tOED
t RAL
t CAL
ro
High-Z
Din
t CAL
t RRH
t RCH
tWP
tCPW
t ASC t CAH
t CAL
tRSH
t RCS
t RCS
Din 3
tOED
tCOP
tWED
tCOL
OE
tAA
tOEA
tCAC
tOEZ
tCPA
tAA
Dout 1
tOEZ
du
t OHO
tOFR
tWEZ
tCPA
tCAC
tRAC
Dout
t OEA
t OHO
Dout 3
tAA
tCAC
tOEZ
tOEA
tOFF
tOH
tOHO
Dout 4
ct
Data Sheet E0152H10
29
EO
HM51W16405 Series, HM51W17405 Series
Test Mode Cycle *19
Set Cycle**
Test Mode Cycle
*,**
Reset Cycle
Normal Mode
RAS
WE
LP
CAS
* CBR or RAS-only refresh
** Address, Din, OE: H or L
ct
du
ro
Data Sheet E0152H10
30
EO
HM51W16405 Series, HM51W17405 Series
Test Mode Set Cycle
t RC
t RP
t RAS
t RP
RAS
Address
t WTH
t CP
High-Z
ct
du
t CRP
ro
t OFF
t RPC
ÃCÃ,ƒÀ‚C€B@,À€@
t WTS
t OFR
Dout
t CHR
tT
t CP
WE
t CSR
LP
CAS
t RPC
Data Sheet E0152H10
31
EO
HM51W16405 Series, HM51W17405 Series
Self Refresh Cycle (L-version)* 23, *24, * 25, * 26
t RASS
t RP
t RPS
RAS
tT
t CP
CAS
t CSR
t WRP
WE
t CRP
LP
,
,
t RPC
t CHS
t WRH
$%&+,
t OFR
t OFF
ro
Dout
High-Z
ct
du
Data Sheet E0152H10
32
EO
HM51W16405 Series, HM51W17405 Series
Package Dimensions
HM51W16405S/LS Series
HM51W17405S/LS Series (CP-26/24DB)
Unit: mm
1.30 Max
ro
0.43 ± 0.10
0.41 ± 0.08
8.51 ± 0.13
7.62 ± 0.13
13
1.27
2.54
Dimension including the plating thickness
Base material dimension
2.65 ± 0.12
6 8
0.74
0.80 +0.25
–0.17
1
14
3.50 ± 0.26
LP
26
16.90
17.27 Max
21 19
+ 0.19
6.79 – 0.18
0.10
Hitachi Code
JEDEC
EIAJ
Weight (reference value)
CP-26/24DB
Conforms
Conforms
0.8 g
ct
du
Data Sheet E0152H10
33
EO
HM51W16405 Series, HM51W17405 Series
HM51W16405TS/LTS Series
HM51W17405TS/LTS Series (TTP-26/24DA)
Unit: mm
13
0.80
0.21 M
9.22 ± 0.20
0.10
Dimension including the plating thickness
Base material dimension
0.145 ± 0.05
0.125 ± 0.04
2.54
0° – 5°
0.50 ± 0.10
Hitachi Code
JEDEC
EIAJ
Weight (reference value)
TTP-26/24DA
Conforms
—
0.30 g
ct
du
ro
1.20 Max
1.15 Max
0.68
0.42 ± 0.08
0.40 ± 0.06
6 8
1.27
0.13 ± 0.05
1
7.62
14
LP
26
17.14
17.54 Max
21 19
Data Sheet E0152H10
34
EO
HM51W16405 Series, HM51W17405 Series
Cautions
ct
du
ro
LP
1. Elpida Memory, Inc. neither warrants nor grants licenses of any rights of Elpida Memory, Inc.’s or any
third party’s patent, copyright, trademark, or other intellectual property rights for information contained
in this document. Elpida Memory, Inc. bears no responsibility for problems that may arise with third
party’s rights, including intellectual property rights, in connection with use of the information contained
in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, contact Elpida Memory, Inc. before using the product in an application that demands
especially high quality and reliability or where its failure or malfunction may directly threaten human
life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control,
transportation, traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Elpida Memory,
Inc. particularly for maximum rating, operating supply voltage range, heat radiation characteristics,
installation conditions and other characteristics. Elpida Memory, Inc. bears no responsibility for failure
or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider
normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic
measures such as fail-safes, so that the equipment incorporating Elpida Memory, Inc. product does not
cause bodily injury, fire or other consequential damage due to operation of the Elpida Memory, Inc.
product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Elpida Memory, Inc..
7. Contact Elpida Memory, Inc. for any questions regarding this document or Elpida Memory, Inc.
semiconductor products.
Data Sheet E0152H10
36
Similar pages