CS4328 18-Bit, Stereo D/A Converter for Digital Audio Features General Description • The CS4328 is a complete stereo digital-to-analog output system. In addition to the traditional D/A function, the CS4328 includes an 8× digital interpolation filter followed by a 64× oversampled delta-sigma modulator. The modulator output controls the reference voltage input to an ultra-linear analog low-pass filter. This architecture allows for infinite adjustment of sample rate between 1 kHz and 50 kHz while maintaining linear phase response simply by changing the master clock frequency. Complete Stereo DAC System 8× Interpolation Filter 64× Delta-Sigma DAC Analog Post Filter System Sampling Rates • Adjustable including 32kHz, 44.1kHz & 48kHz • 120 dB Signal-to-Noise Ratio • Low Clock Jitter Sensitivity Filtered Line-Level Outputs • Completely Linear Phase Filtering Zero Phase Error Between Channels No External Components Needed Serial Interface for Either 16 • Flexible or 18 bit Input Data LRCK BICK SDATAI TST RST DIF0 DIF1 13 12 20 19 18 VD+ The CS4328 also includes an extremely flexible serial port utilizing two select pins to support four different interface modes. The master clock can be either 256 or 384 times the input word rate, supporting various audio environments. ORDERING INFORMATION: CS4328-KP 0 to 70 °C 28-pin Plastic CS4328-KS 0 to 70 °C 28-pin Plastic CS4328-BP -40 to +85 °C 28-pin Plastic CS4328-BS -40 to +85 °C 28-pin Plastic CDB4328 CS4328 Evaluation Board DGND 16 AGND1 17 VA- VA+ 5 3 1 Serial Input Interface 28 Voltage Reference -VREF 8x Interpolator Delta-Sigma Delta-Sigma Modulator Modulator DAC Analog Low-Pass Filter MOSFET Output Stage 2 8x Interpolator Interpolator Delta-Sigma Delta-Sigma Modulator Modulator DAC Analog Low-Pass Filter MOSFET Output Stage 26 10 DIP SOIC DIP SOIC AOUTL 9 Calibration Microcontroller 21 CALO S R A M 8 CMPI Crystal Semiconductor Corporation P.O. Box 17847, Austin, TX 78760 (512) 445-7222 FAX: (512) 445-7581 http://www.crystal.com Clock Osc/ Divider 24 27 XTI XTO CKS ACKO ACKI CALI 15 11 4 25 22 14 AOUTR AGND2 AGND3 6 CMPO Copyright Crystal Semiconductor Corporation 1993 (All Rights Reserved) OCT ’93 DS62F3 1 CS4328 ANALOG CHARACTERISTICS (TA = 25°C for K grade, TA = -40 to +85 °C for B grade; VA+,VD+ = 5V; VA- = -5V; Logic "1" = VD+; Logic "0" = DGND; Full-Scale Output Sinewave, 991 Hz; Input Word Rate = 48 kHz; Input Data = 18 Bits; BICK = 3.072 MHz; RL = 10kΩ; Measurement Bandwidth is 10 Hz to 20 kHz, unweighted; unless otherwise specified.) Parameter* Symbol Specified Temperature Range TA Resolution CS4328-K Min Typ Max 0 CS4328-B Min Typ Max +70 -40 Units +85 °C 16 - - 16 - - Bits 120 - - 120 - - dB Total Harmonic Distortion + Noise (A-Weighted) THD+N 0 dB Output, -20 dB Output, -60 dB Output, - -93 -77 -37 -90 -73 -33 - -88 -75 -35 -85 -70 -30 dB dB dB Deviation From Linear Phase Dynamic Performance Signal-to-Noise Ratio Passband: (A-weighted) (Note 1) SNR (Note 2) - - ± 0.5 - - ± 0.5 - deg to -3 dB corner (Notes 3, 4) - 0 to 23.5 0 to 23.5 kHz to 0.00025 dB corner (Notes 3, 4) 0 to 21.6 0 to 21.6 kHz Frequency Response 10 Hz to 20 kHz (Note 2) - -0.05 +0.1 +0.2 -0.05 +0.1 +0.2 dB Passband Ripple (Note 4) - - - 0.00025 - - 0.00025 dB StopBand (Note 3) - 26.4 - - 26.4 - - kHz StopBand Attenuation (Note 2) - 90 - - 90 - - dB tgd - 33/IWR - - 33/IWR - s - -100 -110 - -95 -105 - dB Interchannel Gain Mismatch - - 0.1 - - 0.1 - dB Gain Error - - - ±5 - - ±5 % Gain Drift - - 150 - - 150 - ppm/°C Offset Error (after calibration) - - - ±1 - - ±1 mV VOUT 3.8 4.0 4.2 3.8 4.0 4.2 Vpp IA+ IAID+ - 40 -40 50 55 -55 60 - 40 -40 50 55 -55 60 mA mA mA - - 650 850 - 650 850 mW PSRR - 50 - - 50 - dB Group Delay (IWR = Input Word Rate) Interchannel Isolation (1 kHz) dc Accuracy Analog Output Full Scale Output Voltage Power Supplies Power Supply Current: VA+ VAVD+ Power Dissipation Power Supply Rejection Ratio (1 kHz) Notes: 1. Idle channel, digital input all zeros. 2. Combined digital and analog filter characteristics. 3. The passband and stopband edges scale with frequency. For input word rates, IWR, other than 48 kHz, the 0.00025 dB passband edge is 0.45×IWR and the stopband edge is 0.55×IWR. 4. Digital filter characteristics. * Definitions are at the end of this data sheet. 2 Specifications are subject to change without notice. DS62F3 CS4328 DIGITAL CHARACTERISTICS (TA = 25 °C; VA+ ,VD+ = 5V ± 5%; VA- = -5V ± 5%) Symbol Min Typ Max Units High-Level Input Voltage Parameter VIH 70%VD+ - - V Low-Level Input Voltage VIL - - 30%VD+ V High-Level Output Voltage at Io = -20µA VOH 4.4 - - V Low-Level Output Voltage at Io = 20µA VOL - - 0.1 V Iin - - 1.0 µA Input Leakage Current (Note 5) Note: 5. TST, DIF0 & DIF1 have internal pull-down devices, nominally 90kΩ. ABSOLUTE MAXIMUM RATINGS (AGND1-3, DGND = 0V, all voltages with respect to ground.) Parameter DC Power Supplies: Symbol Min Positive Digital VD+ -0.3 6.0 V Positive Analog Negative Analog VA+ VA- -0.3 0.3 6.0 -6.0 V V - 0.4 V Iin - ±10 mA VIND -0.3 (VD+)+0.4 V TA -55 125 °C Tstg -65 150 °C |VA+ - VD+| Input Current, Any Pin Except Supplies Digital Input Voltage Ambient Operating Temperature (power applied) Storage Temperature Max Units WARNING: Operation at or beyond these limits may result in permanent damage to the device Normal operation is not guaranteed at these extremes. RECOMMENDED OPERATING CONDITIONS (AGND1, AGND2, AGND3, DGND = 0V; all voltages with respect to ground) Parameter DC Power Supplies: Symbol Min Typ Max Units Positive Digital VD+ 4.75 5.0 5.25 V Positive Analog Negative Analog VA+ VA- 4.75 -4.75 5.0 -5.0 5.25 -5.25 V V - - 0.4 V |VA+ - VD+| DS62F3 3 CS4328 SWITCHING CHARACTERISTICS (TA = 25 °C; VA+, VD+ = 5V ± 5%; VA- = -5V ± 5%; Inputs: Logic 0 = 0V, Logic 1 = VD+, CL = 20 pF) Parameter Symbol Min Typ Max Units XTI/XTO - 10.7 7.1 - 19.2 13.9 MHz MHz XTI/XTO - 0.384 0.256 - 19.2 13.9 MHz MHz XTI/XTO Pulse Width Low - 21 - - ns XTI/XTO Pulse Width High - 21 - - ns BICK Pulse Width Low tbickl 30 - - ns BICK Pulse Width High tbickh 30 - - ns BICK Period tbickw 80 - - ns Master Clock Frequency using Internal Oscillator: CKS=H CKS=L Master Clock Frequency using External Clock: CKS=H CKS=L BICK rising to LRCK edge delay (Note 6) tblrd 35 - - ns BICK rising to LRCK edge setup time (Note 6) tblrs 35 - - ns SDATAI valid to BICK rising setup time (Note 6) tsbs 35 - - ns BICK rising to SDATAI hold time (Note 6) tbsh 35 - - ns RST Minimum Pulse Width Low Note: 2 periods of XTI/XTO 6. "BICK rising" refers to modes 0, 1, and 3. For mode 2, replace "BICK rising" with "BICK falling." LRCK LRCK t blrs t blrd t blrs t bickl t bickh BICK BICK t sbs t bsh Serial Input Timing (Modes 0, 1, &3) t bsh t sbs SDATAI SDATAI 4 t t bickl bickh t blrd MSB MSB-1 Serial Input Timing (Mode 2) DS62F3 CS4328 +5V Digital 10 µF + 16 VD+ 20 Audio Data Processor 19 18 optional crystal oscillator 7 23 74HC device 1.2 M 15 10 pF 15 pF 22 24 External Clock 11 Mode Select Power Up/ Cal. Control 13 12 9 10 µF 0.1 µF VA+ VA- LRCK 5 0.1 µF BICK SDATAI VREFNC + -5V Analog 10 µF 28 0.1 µF CS4328 D/A CONVERTER NC 10 µF + XTO AOUTL 14 + 0.1 µF 3 0.1 µF +5V Analog XTI AOUTR 2 51Ω 26 51Ω ACKO 10 nF NPO 10 nF NPO ACKI CMPO CKS CMPI DIF0 CALO DIF1 CALI 6 8 21 27 RST TST DGND 10 17 AGND3 AGND2 25 AGND1 4 1 Figure 1. Typical Connection Diagram DS62F3 5 CS4328 GENERAL DESCRIPTION The CS4328 is a complete stereo digital-to-analog system designed for digital audio. The system accepts data at standard audio frequencies, such as 48 kHz, 44.1 kHz, and 32 kHz; and produces line-level outputs. The architecture includes an 8× oversampling filter followed by a 64× oversampled one-bit delta-sigma modulator. The output from the one bit modulator controls the polarity of a reference voltage which is then passed through an ultralinear analog low-pass filter. The result is line-level outputs with no need for further filtering. SYSTEM DESIGN Very few external components are required to support the DAC. Normal power supply decoupling components and voltage reference bypass capacitors are all that’s required. System Clock Input The master clock (XTI/XTO) input to the DAC is used to operate the digital interpolation filter and the delta-sigma modulator. The master clock can be either a crystal placed across the XTI and XTO pins, or an external clock input to the XTI pin with the XTO pin left floating. The frequency of XTI/XTO is determined by the desired Input Word Rate, IWR, and the setting of the Clock Select pin, CKS. IWR is the frequency at which words for each channel are input to the DAC and is equal to LRCK frequency. Setting CKS low selects an XTI/XTO frequency of 256× IWR while setting CKS high selects 384× IWR. The ACKO pin will always be 128× IWR and is used by the analog low-pass smoothing filter. Table 1 illustrates various audio word rates and corresponding frequencies used in the DAC. 6 LRCK (kHz) 32 CKS low XTI/XTO (MHz) 8.192 ACKO (MHz) 4.096 32 high 12.288 4.096 44.1 low 11.2896 5.6448 44.1 high 16.9344 5.6448 48 low 12.288 6.144 48 high 18.432 6.144 Table 1. Common Clock Frequencies The remaining system clocks, LRCK and BICK, must be synchronously derived from XTI/XTO. If the CS4328 internal oscillator is used, the circuit must be configured and XTO buffered as shown in Figure 1. XTI/XTO can be divided to produce LRCK and BICK using a synchronous counter such as 74HC590. Notice that the value of the capacitor on XTO is 10 pF and the XTI capacitor is 15 pF, which allows for 5 pF of gate and stray capacitance. It is also possible to divide ACKO, 128× IWR, to derive BICK and LRCK. However, external circuitry must be used to apply a "kick-start" pulse to LRCK in order to activate ACKO. The sequence for the cancellation of RESET, beginning of calibration and activation of ACKO is shown in Figure 2 with the required transitions indicated by arrows. A momentary loss of XTI/XTO or power will require a "kick-start" pulse to resume operation. Serial Data Interface Data is input to the CS4328 via three serial input pins; SDATAI is the serial data input, BICK is the serial data clock and LRCK defines the channel and delineation of data. The DAC supports four serial data formats which are selected via the digital input format pins DIF0 and DIF1. The different formats control the relationship of LRCK to SDATAI and the edge of BICK used to DS62F3 CS4328 RST 40 ns minimum 40 ns minimum LRCK "Kickstart" XTI/XTO ACK0 Reset Status Exit Reset Figure 2. RESET Cancellation Timing latch data. Table 2 lists the four formats, along with the associated figure number. Format 0 is compatible with existing 16-bit D/A converters and digital filters. Format 1 is an 18-bit version of format 0. Format 2 is similar to Crystal ADCs and many DSP serial ports. Format 3 is compatible with the I2S serial data protocol. Formats 2 and 3 support 18-bit input or 16-bit followed by two zeros. In all four serial input modes, the serial data is MSB-first and 2’s-complement format. Formats 0, 2 and 3 will operate with 16-bit data and 16 BICK pulses as well. See Figure 6 for 16-bit timing. However, the use of BICK = 64× IWR is recommended to minimize the possibility of performance degradation resulting from BICK coupling into VREF-. DIF1 0 DIF0 0 Mode 0 Figure 3 0 1 1 3 1 0 2 4 1 1 3 5 Table 2. Digital Input Formats DS62F3 Reset and Offset Calibration RST is an active low signal that resets the digital filter and the delta-sigma modulator, synchronizes LRCK with internal control signals and starts an offset calibration cycle upon exiting reset. When RST goes low, CALO goes high and stays high until the end of an offset calibration cycle. An offset calibration cycle takes 1024 IWR cycles to complete. CALO must be connected to CALI and CMPO must be connected to CMPI for offset calibration. During an offset calibration the analog output is forced to zero. Power-Up Considerations Upon initial application of power to the DAC, offset calibration and digital filter registers will be indeterminate. RST should be low during power-up to activate an internal mute and prevent this erroneous information from being output from the DAC. Bringing RST high will begin a calibration cycle and initialize these registers. Muting There are two types of mutes that can be implemented with the CS4328. The first is a -50 dB 7 CS4328 Right Channel Left Channel LRCK BICK SDATAI Mode 0 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 SDATAI Mode 1 1 0 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Figure 3. Digital Input Formats 0 & 1 Right Channel Left Channel LRCK BICK SDATAI 16 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 SDATAI 18 Bit 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 17 Figure 4. Digital Input Format 2 Left Channel LRCK Right Channel BICK SDATAI 16 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 SDATAI 18 Bit 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Figure 5. Digital Input Format 3 Left Channel LRCK Right Channel BICK SDATAI Mode 2 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 BICK SDATAI Mode 0 * SDATAI Mode 3 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 * LRCK must be inverted. Figure 6. Digital Input Formats 0, 2 and 3 with 16 BICK Periods 8 DS62F3 CS4328 CS4328 21 27 MUTE CALO CALI Figure 7. -50dB Muting mute which can be activated by forcing the CALI pin high. Figure 7 shows how to implement a -50 dB mute using an OR gate. The propagation of the gate will be the only delay in moving the CS4328 to a muted state. _____ MUTE DATA CS4328 18 SDATAI Figure 8. -120 dB Muting The second mute option is a two stage operation which involves forcing SDATAI to 0 using an AND gate as shown in Figure 8. The first mute occurs following 33 LRCK cycles when the 0 input data propagates to the output of the DAC. The rms noise present at the output will typically be 93 dB below fullscale. Following a total of 4096 LRCK cycles with 0 input data the output of the CS4328 will mute and lower the output rms noise to a minimum of 120 dB below fullscale. Upon release of the MUTE command and non-zero input data the CS4328 output mute will immediately release. However, 33 LRCK cycles are required for input data to propagate to the output of the CS4328. Grounding and Power Supply Decoupling As with any high resolution converter, the CS4328 requires careful attention to power supply and grounding arrangements to optimize performance. Figure 1 shows the recommended power arrangements with VA+ connected to a clean +5 volt supply and VA- connected to a DS62F3 clean -5 volt supply. VD+, which powers the digital interpolation filter and delta-sigma modulator, may be powered from the system +5 volt logic supply. Decoupling capacitors should be located as near to the CS4328 as possible. The printed circuit board layout should have separate analog and digital regions with individual ground planes. The CS4328 should straddle the ground plane break as shown on the CDB4328 Evaluation board. Optional jumpers for connecting these planes should be included near the DAC, where power is brought on to the board and near the regulators. All signals, especially clocks, should be kept away from the VREF- pin to avoid unwanted coupling into the CS4328. The VREF- decoupling capacitors, particularly the 0.1 µF, must be positioned to minimize the electrical path from VREF- to Pin 1 AGND and to minimize the path between VREF- and the capacitors. Extensive use of ground plane fill on both the analog and digital sections of the circuit board will yield large reductions in radiated noise effects. An application note "Layout and Design Rules for Data Converters" is printed in the Application Note section of this book. Analog Output and Filtering Full scale analog output for each channel is typically 4V peak-to-peak. The analog outputs can drive load impedances as low as 600Ω and are short-circuit protected to 20mA. The CS4328 analog filter is a 5th order switched-capacitor filter followed by a secondorder continuous-time filter. The switched-capacitor filter is clock dependent and will scale with the IWR frequency. The continuous-time filter is fixed and not related to IWR. A low-pass filter consisting of a 51Ω resistor and a .01 µF NPO capacitor is recommended on the analog outputs. 9 CS4328 Performance Plots The following collection of CS4328 measurement plots (IWR = 48 kHz) were taken with an Audio Precision Dual Domain System One. All FFT plots are 16,384 point. Figure 9 shows the frequency response with a 48 kHz input word rate. The response is very flat out to half the input word rate. Figure 10 shows the muted noise with all zeros data into the CS4328. This plot is dominated by the noise floor of the System One. Figure 11 shows the unmuted noise. This data was taken by feeding the CS4328 continuous zeros, but pulling CALI low. This unmutes the output stage of the CS4328. This plot shows the noise shaping characteristics of the delta-sigma modulator combined with the analog filter. Figure 12 shows the A-weighted THD+N vs signal amplitude for a dithered 1kHz input signal. Notice that there is no increase in distortion as the signal level decreases. This indicates very good low-level linearity, one of the key benefits of the delta-sigma technique. Figure 13 shows the fade-to-noise linearity test result using track 20 of the CBS CD-1. The input test signal is a dithered 500 Hz sine wave which gradually fades from -60 dB level to -120 dB. During the fading, the output level from the CS4328 is measured and compared to the ideal level. Notice the very close tracking of the output level to the ideal, even at low level inputs of -90 dB. The gradual shift of the plot away from zero at signal levels < -100 dB is caused by the background noise starting to dominate the measurement. Figure 15 shows a 16K FFT plot result, with a 1 kHz -90 dB dithered input. Notice the complete lack of distortion components and tones. Figure 16 shows a bandlimited, 10 Hz to 22 kHz, time domain plot of the CS4328 output with a 1 kHz, -90 dB dithered input. Notice the clear residual sine wave shape, in the presence of noise. Figure 17 shows the monotonicity test result plot. The input data to the CS4328 is +1 LSB, -1 LSB four times, then +2 LSB, -2 LSB four times and so on, until +10 LSB, -10 LSB. This data pattern is taken from track 21 of the CD-1 test disk. Notice the increasing staircase envelope, with no decreasing elements. Notice also the clear resolution of the LSB. For this test, one LSB is a 16-bit LSB. The following tests were done by filtering the analog output of the CS4328 with the System One analyzer 1 kHz notch filter to reduce the peak signal level. The resulting signal was then amplified and applied to the DSP module, avoiding distortion in the System One A/D converter. Figure 18 shows a 16K FFT Plot with a 1 kHz, 0 dB input. Notice the low order harmonic distortion at < -100 dB. Figure 19 shows a 16K FFT Plot with a 1 kHz, -10 dB input. Notice the almost complete absence of distortion, with a small residual 2nd harmonic at -110 dB. Figure 14 shows the impulse response, taken from the single positive full scale value on track 17 of the CD-1 test disk. Notice the high degree of symmetry, indicating good phase linearity. 10 DS62F3 CS4328 CRYSTAL 2.0 AMPL(dBr) vs GENFRQ(Hz) FRQRSP48 CRYSTAL THDAM18A -80 THD+N(dBr) vs GENAMP(dBFS) -82 1.5 -84 1.0 -86 0.5 -88 -90 0.0 -92 -0.5 -94 -1.0 -96 -1.5 -98 -2.0 10 100 1k 10k 30k Figure 9. Frequency Response (48 kHz word rate) AMP1(dBr) & AMP1(dBr) vs FREQ(kHz) CRYSTAL NOISE 0 -100 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 Figure 12. THD+N vs 18-bit Input Signal Level BANDPASS(dBr) CRYSTAL TR20R 10 vs LEVEL(dBr) 8 -20 6 -40 4 -60 2 0 -80 -2 -100 -4 -120 -6 -140 -160 0.02 -8 9.82 19.6 29.4 39.2 49.0 58.8 68.6 78.4 88.2 98.0 -10 -120 Figure 10. Muted Idle Channel Noise AMP1(dBr) CRYSTAL NOISEUNM 0 vs -110 -100 -90 -80 -70 -60 Figure 13. Fade-to-Noise Linearity FREQ(kHz) CRYSTAL 2.000 AMP1(V) vs TIME(usec) IMPULSE -20 1.583 -40 1.167 -60 -80 0.750 -100 0.333 -120 -0.083 -140 -160 0.02 9.82 19.6 29.4 39.2 49.0 58.8 68.6 78.4 Figure 11. Unmuted Idle Noise DS62F3 88.2 98.0 -0.500 0.0 95.8 192 287 383 479 575 670 766 862 Figure 14. Impulse Response 11 CS4328 CRYSTAL M90DB1K 0 AMP1(dBr) vs FREQ(kHz) CRYSTAL 800 AMP1(uV) MONOTON vs TIME(msec) 640 -20 480 -40 320 160 -60 0 -80 -160 -320 -100 -480 -120 -640 -140 -800 20 100 1k 10k 20k 0 Figure 15. 1 kHz, -90 dB Input FFT Plot CRYSTAL 250 AMP1(uV) M90TIME 5 10 15 20 25 30 35 40 45 50 Figure 17. Monotonicity Test (16-bit data) vs TIME(msec) CRYSTAL 1k 0dBFFT 0 AMP1(dBr) vs FREQ(Hz) 200 -20 150 -40 100 50 -60 0 -80 -50 -100 -100 -150 -120 -200 -250 -140 0.0 0.50 1.00 1.50 2.00 2.50 3.00 20 Figure 16. 1 kHz, -90 dB Input Time Domain Plot CRYSTAL 0 1KM10DB 100 1k 10k 20k Figure 18. 1 kHz, 0 dB Input FFT Plot AMP1(dBr) vs FREQ(Hz) -20 -40 -60 -80 -100 -120 -140 20 100 1k 10k 20k Figure 19. 1 kHz, -10 dB Input FFT Plot 12 DS62F3 CS4328 8x Interpolator Audio Data Digital Delta Sigma Modulator 8 X S/H Switched Continuous Cap Time LPF Filter Analog Filter DAC Analog Output Figure 20. CS4328 Architecture THEORY OF OPERATION The CS4328 architecture can be considered in five blocks: Interpolation, sample/hold, deltasigma modulation, D/A conversion, and analog filtering. Audio data is input to the CS4328 digital interpolation filter which removes images of the input signal that are present at multiples of the input sample frequency, Fs (Figure 21). Following the interpolation stage, the resulting frequency spectrum has images of the input signal at multiples of eight times the input sample frequency, 8× Fs (Figure 22). Eliminating the images between Fs and 8× Fs greatly relaxes the requirements of the analog filtering, allowing the suppression of images while leaving the audio band of interest unaltered. (dB) 24 Fs 2Fs tiples. The sinx/x zeros completely attenuate signals at 8× Fs and largely suppress the remaining energy of the images (Figure 23). The 8× interpolation followed by the 8× sample-and(dB) 24 8Fs 16Fs f (kHz) Figure 23. Spectrum After S/H hold results in data at a rate of 64× Fs. The delta-sigma modulator takes in the 64× Fs data (3.072 MHz for 48kHz sampled systems) and performs fifth-order noise shaping. In the digital modulator of the CS4328, 18-bit audio data is modulated to a 1-bit, 64× Fs signal. The 5th-order noise shaper allows 1-bit quantization to support 18-bit audio processing by suppressing quantization noise in the bandwidth of f (kHz) Figure 21. Input Data Spectrum (dB) 24 (dB) f(kHz) Figure 24. Modulator Output Spectrum 24 8Fs 16Fs f (kHz) Figure 22. 8X Interpolated Data Spectrum interest. Figure 24 shows the frequency spectrum of the modulator output. The CS4328 interpolation stage is followed by a sample-and-hold function where the data points from the interpolator are held for eight (64× Fs) clock cycles. The resulting frequency response is a sinx/x characteristic with zeros at 8× Fs mulDS62F3 The CS4328’s digital modulator is followed by a D-to-A converter that translates the 1-bit signal into a series of charge packets. The magnitude of the charge in each packet is determined by sampling of a voltage reference onto a switched 13 CS4328 capacitor, where the polarity of each packet is controlled by the 1-bit signal. The result is a 1-bit D/A conversion process that is very insensitive to clock jitter. This is a major improvement over previous generations of 1-Bit D/A converters where the magnitude of charge in the D/A process is determined by switching a current reference for a period of time defined by periods of the master clock. The final stage of the CS4328 is made up of a 5th order switched-capacitor low pass filter and a 2nd order continuous time filter. The switchedcapacitor filter eliminates out-of-band energy resu lting from the n oise shaping process (Figure 25). The switched-capacitor stage scales with the master clock signal being applied to the CS4328. The final stage is a 2nd order continuous time filter that eliminates high frequency energy that appears at multiples of the 64× Fs sample rate (Figure 26). Figures 27-30 are computer simulations of the combined response of the CS4328 digital and analog filters with an input word rate of 48 kHz. Figure 27 shows the individual and combined phase response of the CS4328 filters. Notice the digital filter equalization of the analog filter to produce a linear phase response. Figures 28-30 are plots of the CS4328 magnitude response. 20 (dB) 16 64Fs f (kHz) Figure 25. Spectrum After Switched-Capacitor Filter (dB) Phase (degrees) 12 24 Analog Filter 8 4 Total Phase 0 -4 -8 Digital Filter -12 -16 24 f (kHz) -20 0 2 4 6 8 10 12 14 Frequency (kHz) 16 18 20 Figure 26. Spectrum After Continuous Time Filter Figure 27. Deviation From Linear Phase 14 DS62F3 CS4328 Magnitude (dB) 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 0 8 16 24 32 Input Frequency (kHz) 40 48 Figure 28. Combined Digital and Analog Filter Frequency Response 1 0 Magnitude (dB) -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 20 21 22 23 Input Frequency (kHz) 24 25 Figure 29. Combined Digital and Analog Filter Frequency Response 0 -10 Magnitude (dB) -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 22 23 24 25 26 27 Input Frequency (kHz) 28 29 30 Figure 30. Combined Digital and Analog Filter Transition Band DS62F3 15 CS4328 PIN DESCRIPTIONS ANALOG GROUND ANALOG LEFT CHANNEL OUTPUT ANALOG POWER ANALOG GROUND NEGATIVE ANALOG POWER COMPARATOR OUTPUT NO CONNECT COMPARATOR INPUT RESET TEST CLOCK SELECT DIGITAL INPUT FORMAT 1 DIGITAL INPUT FORMAT 0 CRYSTAL OR CLOCK INPUT AGND1 AOUTL VA+ AGND2 VACMPO NC CMPI RST TST CKS DIF1 DIF0 XTI 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 VREF- VOLTAGE REFERENCE OUTPUT CALI CALIBRATION INPUT AOUTR ANALOG RIGHT CHANNEL OUTPUT AGND3 ANALOG GROUND ACKI ANALOG CLOCK INPUT NC NO CONNECT ACKO ANALOG CLOCK OUTPUT CALO CALIBRATION OUTPUT LRCK LEFT/RIGHT CLOCK INPUT BICK SERIAL BIT CLOCK INPUT SDATAI SERIAL DATA INPUT DGND DIGITAL GROUND VD+ DIGITAL POWER XTO CRYSTAL OSCILLATOR OUTPUT Power Supply Connections VA+ - Positive Analog Power, PIN 3. Positive analog supply. Nominally +5 volts. VA- - Negative Analog Power, PIN 5. Negative analog supply. Nominally -5 volts. AGND1, AGND2, AGND3 - Analog Grounds, PINS 1, 4, 25. Analog ground reference. VD+ - Positive Digital Power, PIN 16. Positive supply for the digital section. Nominally +5 volts. DGND - Digital Ground, PIN 17. Digital ground for the digital section. Analog Outputs VREF- - Voltage Reference Output, PIN 28. Nominally -3.68 volts. Normally connected to a 0.1µF ceramic capacitor in parallel with a 10µF or larger electrolytic capacitor. Note the negative output polarity. AOUTL - Analog Left Channel Output, PIN 2. Analog output for the left channel. Typically 4V peak-to-peak for a full-scale input signal. AOUTR - Analog Right Channel Output, PIN 26. Analog output for the right channel. Typically 4V peak-to-peak for a full-scale input signal. 16 DS62F3 CS4328 Digital Inputs XTI - Crystal or Clock Input, PIN 14. A crystal oscillator can be connected between this pin and XTO, or an external CMOS clock can be input on XTI. The frequency must be either 256× or 384× the input word rate based on the clock select pin, CKS. ACKI - Analog Clock Input, PIN 24. This is the master clock input for the analog section of the chip and must be 128× the input word rate. ACKI is typically connected to the Analog Clock Ouput pin, ACKO. CALI - Calibration Input, PIN 27. Input to the analog section that is used during offset calibration. Normally connected to the Calibration Output pin, CALO. CMPI - Comparator Input, PIN 8 Input to the digital section that is used during offset calibration. Normally connected to the Comparator Output pin, CMPO. LRCK - Left/Right Clock, PIN 20. This input determines which channel is currently being input on the Serial Data Input pin, SDATAI. The format of LRCK is controlled by DIF0 and DIF1. BICK - Serial Bit Input Clock, PIN19. Clocks the individual bits of the serial data in from the SDATAI pin. The edge used to latch SDATAI is controlled by DIF0 and DIF1. SDATAI - Serial Data Input, PIN 18. Two’s complement MSB-first serial data of either 16 or 18 bits is input on this pin. The data is clocked into the CS4328 via the BICK clock and the channel is determined by the LRCK clock. The format for the previous two clocks is determined by the Digital Input Format pins, DIF0 and DIF1 DIF0,DIF1 - Digital Input Format, PINS 13, 12 These two pins select one of four formats for the incoming serial data stream. These pins set the format of the BICK and LRCK clocks with respect to SDATAI. The formats are listed in Table 2. CKS - Clock Speed Select, PIN 11. Selects the clock frequency input on the XTI pin. CKS low selects 256× the input word rate (LRCK frequency) while CKS high selects 384×. RST - Reset and Calibrate, PIN 9. When reset is low the filters and modulators are held in reset. When reset goes high, an offset calibration is initiated. DS62F3 17 CS4328 Digital Outputs XTO - Crystal Oscillator Output, PIN 15. When a crystal oscillator is used, it is tied between this pin and XTI. When an external clock is input, this pin should be left floating. ACKO - Analog Clock Output, PIN 22. This output is 128× the input word rate (LRCK frequency). Normally connected to the Analog Clock Input pin, ACKI. CALO - Calibration Output, PIN 21. Used during offset calibration. Must be connected to the Calibration Input pin, CALI. CMPO - Comparator Output, PIN 6. Used during offset calibration. Must be connected to the Comparator Input pin, CMPI. Miscellaneous NC - No Connection, PINS 7, 23. These two pins are bonded out to test outputs. They must not be connected to any external component or any length of PC trace. TST -Test Input, PIN 10. Allows access to the CS4328 test modes, which are reserved for factory use. Must be tied to DGND. 18 DS62F3 CS4328 PARAMETER DEFINITIONS Total Harmonic Distortion + Noise - The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified bandwidth (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Signal-to-Noise Ratio - The ratio of the full scale rms value of the signal to the rms sum of all other spectral components over the specified bandwidth with an input of all zeros. Frequency Response - A measure of the amplitude response variation from 10 Hz to 20 kHz relative to the amplitude response at 1 kHz. Units in decibels. Interchannel Isolation - A measure of crosstalk between the left and right channels. Measured for each channel at the converter’s output with all zeros to the input under test and a full-scale signal applied to the other channel. Units in decibels. Interchannel Gain Mismatch - The gain difference between left and right channels. Units in decibels. Gain Error - The deviation from the nominal full scale analog output for a full scale digital input. Gain Drift - The change in gain value with temperature. Units in ppm/°C. Offset Error - The deviation of the mid-scale transition (111...111 to 000...000) from the ideal (AGND). Units in mV. DS62F3 19 MILLIMETERS INCHES DIM MIN NOM MAX MIN NOM MAX 3.94 4.32 5.08 0.155 0.170 0.200 A A1 0.51 0.76 1.02 0.020 0.030 0.040 0.36 0.46 0.56 0.014 0.018 0.022 B B1 1.02 1.27 1.65 0.040 0.050 0.065 C 0.20 0.25 0.38 0.008 0.010 0.015 36.45 36.83 37.21 1.435 1.450 1.465 D E1 13.72 13.97 14.22 0.540 0.550 0.560 e1 2.41 2.54 2.67 0.095 0.100 0.105 eA 15.24 15.87 0.600 0.625 L 3.18 0.150 3.81 0.125 0° 15° 15° 0° ∝ 15 28 28 pin Plastic DIP E1 1 14 D A SEATING PLANE A1 L ∝ e1 B1 B C eA NOTES: 1. POSITIONAL TOLERANCE OF LEADS SHALL BE WITHIN 0.25mm (0.010") AT MAXIMUM MATERIAL CONDITION, IN RELATION TO SEATING PLANE AND EACH OTHER. 2. DIMENSION eA TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION E1 DOES NOT INCLUDE MOLD FLASH. INCHES MIN NOM MAX 0.390 0.400 0.410 0.490 0.500 0.510 0.590 0.600 0.610 28 MILLIMETERS MIN NOM MAX 9.91 10.16 10.41 12.45 12.70 12.95 14.99 15.24 15.50 17.53 17.78 18.03 DIM MILLIMETERS MIN NOM MAX INCHES MIN NOM MAX pins 16 20 24 D SOIC E1 E A2 e b A1 A µ c L 0.690 0.700 0.710 2.54 2.67 0.095 0.100 0.105 0.300 0.005 0.012 2.41 2.54 0.090 0.095 0.100 A A1 A2 2.41 0.127 b c 0.33 0.46 0.51 0.013 0.018 0.020 0.203 0.280 0.381 0.008 0.011 0.015 see table above D E E1 e L µ 2.29 10.11 10.41 10.67 0.398 0.410 0.420 7.42 7.49 7.57 0.292 0.295 0.298 1.14 0.41 1.27 - 0° - 1.40 0.040 0.050 0.055 0.89 0.016 0.035 0° 8° 8° CDB4328 CS4328 Evaluation Board Features General Description • The CDB4328 evaluation board allows fast evaluation of the CS4328 18-bit, stereo D/A converter. The board provides an analog output interface via BNC connectors for both channels. Evaluation requires an analog signal analyzer, a digital signal source, and a power supply. Demonstrates recommended layout and grounding arrangements • CS4328 Supports multiple input formats • CS8412 Receives AES/EBU, S/PDIF, & EIAJ-340 Compatible Digital Audio Also included is a CS8412 digital audio receiver I.C., which will accept AES/EBU, S/PDIF, and EIAJ-340 compatible audio data. The CS8412 can provide the system timing necessary to operate the CS4328. The evaluation board may also be configured to accept external timing signals for operation in a user application during system development. • Digital and Analog Patch Areas • Operation with on-board CS8412 or externally supplied system timing ORDERING INFORMATION: CDB4328 Block Diagram Digital Audio Input Digital Patch Area Error Info/ Channel Status -15V GND GND +5V Analog Patch Area CS8412 Digital Audio Receiver 6 +15V Power Supply Regulation and Conditioning Timing Signal Selector CS4328 D/A Converter AOUTR AOUTL Offset Calibration Network L/R SCLK SDATA MCLK Crystal Semiconductor Corporation P.O. Box 17847, Austin, TX 78760 (512) 445 7222 Fax: (512) 445 7581 http://www.crystal.com AUG ’93 DS62DB2 21 CDB4328 Power Supply Circuitry Offset Calibration & Reset Circuitry Figure 1 shows the evaluation board power supply circuitry. Power is supplied to the evaluation board by five binding posts. The +5 V analog power supply inputs of the converter are derived from + 15 V using the voltage regulators U5 and U6. The +5 V digital supply for the converter and the discrete logic on the board is provided by the +5 V and DGND binding posts. D1, D2, and D3 are transient suppressors which also provide protection from incorrectly connected power supply leads. C1-C8 provide general power supply filtering for the analog supplies. As shown in Figure 2, C20-C24 provide localized decoupling for the converter VA+ and VApins. Note that C22 is connected between VAand VA+ and not VA- and AGND. The evaluation board uses both an analog and a digital ground plane which are connected at J1. This ground plane arrangement isolates the board’s digital logic from the analog circuitry. Figure 1, shows the offset calibration circuit provided on the evaluation board. Upon power-up, this circuit provides a pulse on the Digital to Analog Converter’s RST pin initiating an offset calibration cycle. Pressing and releasing S2 also initiates an offset calibration cycle. Serial Data Interface Figure 1 shows that there are two options for inputing serial data into the CS4328. Serial data can be provided via the SDATA BNC connector on the evaluation board. BNC connectors for SCLK, the serial data input clock, and L/R, the clock that defines the channel and delineates the data, are also provided on the evaluation board. This information can also be provided by the onboard CS8412. JP3 selects the source of SDATA, SCLK, and L/R that will be provided to the converter. JP3 selections are shown in Table 1. U5 IN 78L05 OUT COM +15V D2 + C3 47 uF VA+ C6 C7 0.22 uF 0.47 uF C5 C8 0.22 uF 0.47 uF J1 AGND + C4 D3 47 uF COM 79L05 OUT U6 IN -15V AGND VA- 5 D2 = D3 = 1N6276A 1.5KE D1 = P6KE-6V8P from Thomson +5V + C1 47 uF C2 0.1 uF D13 1N148 RST CS4328 R4 10kΩ 3 DGND S2 CAL 6 U7C VD+ VD+ D1 DGND 0.1uF C15 4 U7B 74HC14 Figure 1. Power Supply and Reset Circuitry 22 DS62DB2 CDB4328 VD+ 1 uF C26 + 0.1 uF C25 7 NC 23 NC U3, Pin 3 U3, Pin 6 U3, Pin 8 U3, Pin 11 TP 20 TP 19 TP 18 TP 14 16 22 VD+ ACKO 3 24 ACKI VA+ AGND1 VAAGND2 LRCK 1 C22 0.1 uF 5 C21 0.1 uF 4 AGND3 SDATAI 6 CMPO 8 CMPI 21 CALO 27 CALI 2 R5 AOUTL 51Ω XTI U1 CS4328 XTO AOUTR 26 R6 51Ω From Reset Circuit 9 VREF RST TST DGND CKS 10 17 11 JP2 DIFO 13 DIFI 12 + +5V Analog, C24 VA+ 1.0 uF -5V Analog, C20 VA+ 1.0 uF 25 BICK L/R SCLK SDATA MCLK 15 C23 0.1 uF TP C18 10 nF NPO TP C19 10 nF NPO AOUTL AOUTR 28 C16 0.1 uF C17 10 uF + R11 47kΩ VD+ VD+ Figure 2. CS4328 DAC Connections The CS4328 supports four serial data input formats. The selection of which is made via the digital input format pins DIF0 and DIF1. The different formats control the relationship of L/R to SDATA and the edge of SCLK used to latch the data. Consult the CS4328 data sheet for an explanation of the different formats. Position Input Option Selected EXT CLK SDATA,SCLK, L/R provided by an external source. 8412 SDATA,SCLK, L/R provided by the CS8412 Table 1. JP3 Selectable Options DS62DB2 System Timing The master clock input to the CS4328 can be provided by several sources. JP3 selects the source of the master clock that is to be supplied to the XTI pin of the converter. When EXT CLK is selected, the master clock is provided by one of two sources. The 12.288 MHz clock signal provided by U8 can be used as the master clock for both the CS4328 and the external system that provides the serial data to the board. The other option is for a master clock that is synchronized to the external serial data coming into the board, be used as the master clock for the CS4328 as well. However, if an external 23 CDB4328 master clock is to be used, U8 must be removed from it’s socket to prevent the two clock signals from interfering with one another. When 8412 is selected by JP3, the master clock for the CS4328 is provided by the MCK output of the CS8412. The CKS pin of the CS4328 can be pulled either high or low via JP2. This determines whether the master clock frequency has to be 384X or 256X the input word rate. Consult the CS4328 data sheet for the common master clock frequencies table. Analog Outputs The analog outputs are available at 2 BNC connectors labeled AOUTL and AOUTR. R5 and C18 remove the remaining very high frequency components from the left channel output signal while R6 and C19 do so for the right channel output signal. Digital Audio Standard Interface Included on the evaluation board is a CS8412 Digital Audio Interface Receiver. This device can receive and decode data according to the AES/EBU, S/PDIF, and EIAJ-340 interface standard. Figure 3 shows the schematic for the CS8412. The input is coupled to the device through a transformer that is included on the board. The input to the device can be configured to accept either professional or consumer input modes. Consult the CS8412 data sheet for an explanation of the two input modes. The LEDs, D4-D8, perform two functions. When S1 is in the Channel Status position, the LEDs display the channel status information for the channel selected by JP1. When S1 is in the Error Information position, the LEDs D4-D6, display encoded error information that can be decoded by consulting the CS8412 data sheet. Encoded sample frequency information is displayed on LEDs D7-D9 provided a proper clock is being applied to the FCK pin of JP1. When an LED is lit, this indicates a "1" on the corre24 sponding pin located on the CS8412. When an LED is off, this indicates a "0" on the corresponding pin. Neither the L or R option should be selected if the FCK pin of JP1 is being driven by a clock signal. Serial Output Interface The SDATA, SCLK, L/R, and MCLK BNC connectors can also be used to provide a serial output interface for the CS8412. With JP3 in the 8412 position, the outputs from the CS8412 can be brought off the board to an external evalution system. This data can be configured in one of seven selectable formats. These formats are outlined in the CS8412 data sheet. CDB5336/7/8/9 Interface to CDB4328 Many users find it informative to evaluate a combined ADC and DAC system connected together yielding analog input and analog output. This can be accomplished by interconnecting a CDB5326/7/8/9 or CDB5336/7/8/9 to a CDB4328 evaluation board. The following information contains several techniques to accomplish this goal. There are two general points which need to be mentioned. An analog input of ± 3.68 V will produce a full scale digital output from the CS5336/7/8/9 and the CS5326/7/8/9. A full scale digital input to the CS4328 will produce a full scale output of ± 2 V resulting in an overall loss of approximately 5.2 dB from input to output. Also it is recommended that the power connections for each board are brought directly from the power supply and not in a "daisy-chain" manner from board to board. Connecting the CDB4328 to the CDB5336/7/8/9 can be accomplished using one of two methods: DS62DB2 DS62DB2 FCK R7 JP1 VD+ L R 47 k VD+ D7 D8 12 D9 560 560 560 4 2 110 R8 Ce/F2 Cd/F1 Cc/F0 Cb/E2 Ca/E1 RXN 19 M0 23 24 M1 18 M2 17 M3 MCK SDATA 26 SCK 12 VD+ 0.1 uF C11 7 R9 10 22 +5V Analog 21 FILT 20 8 DGND VD+ AGND VA+ 10 U2 CS8412 CSLR/FCK 15 CBL RXP 9 13 27 2 3 4 5 16 25 1 14 28 SEL ERF C U VERF FSYNC 11 6 C0/E0 TP 1k VD+ 1.0 uF 12 9 5 0.1 uF C10 + 8 6 7 13 1.0 uF C9 12 10 13 11 U7 D,E,F 7 JP3 9 7 5 3 1 VD+ 8 14 Pin 18, U1 Pin 19, U1 Pin 20, U1 0.1 uF R3 47k 0.1 uF U3 74HC126 11 10 4 0.047 uF 1 C29 14 2 3 C12 VD+ 47 k R12 47 k R13 47 k R1 47 k R2 R10 Error Information Channel Status VD+ S1 TP TP TP U7A 1 Figure 3. CS8412 Digital Audio Receiver Connections 3 TP U4 74HC04 1 13 3 11 5 C27 0.1 uF 9 1 1:1 7 2 4 Schott 67125450 Pulse PE65612 Digital Input D6 10 560 6 D5 560 8 D4 560 RP1 7 Pin SIP VD+ 2 8 1 NC U6 12.288 MHz VCC GND 7 14 + C14 C13 EXT CLK 8412 0.1 uF C28 Pin 14, U1 8 6 4 2 VD+ CDB4328 25 CDB4328 the trace at the SDATA BNC connector and place a jumper between the SDATA BNC and U8 pin 11. CMODE is set LOW for a master clock of 256 times the sample rate. P7 must have both the internal and external jumpers installed. This will route the master clock to the EXTCLKIN BNC fo r co nn ection to the CDB4328 MCLK. If a CS5336/8 is installed an additional modification is required to invert the SCLK prior to transmission to the CDB4328. This can be implemented as follows: cut the trace at the SCLK BNC and install a jumper between U7 pin 4 and the SCLK BNC. CDB5336/7/8/9 and CDB4328 Interconnection for Method 2 Shielded coaxial cables with BNC connectors should be used to make the following connections: L/R to L/R, SCLK to SCLK, SDATA to SDATA, EXTCKIN to MCLK. CDB4328 Interfacing to the CDB5326/7/8/9 be removed to access the multiple clocks from the CDB5326/7/8/9. Remove the 12.288 MHz oscillator (U8). CDB5326/7/8/9 Configuration Remove the clock source jumper (P2). Remove the 6.144 MHz oscillator (U2) and replace with the 12.288 MHz oscillator from the CDB4328. Install a divide by 2 function on the CDB5326/7/8/9 digital patch area. Use a 74HC74 with the D input connected to the Q output. Connect the oscillator output to the 74HC74 clock input. Connect the Q output to U1 pin 23. Position P2 to connect the oscillator output to the EXTCLKIN. CDB5326/7/8/9 and CDB4328 Interconnection Shielded coaxial cables with BNC connectors should be used to make the following connections: L/R to L/R, SCLK to SCLK, SDATA to SDATA, EXTCLKIN to MCLK. A method of interfacing the CDB5326/7/8/9 and the CDB4328 requires a direct interface through the EXTCLKIN, SCLK, SDATA, and L/R BNC connectors. This technique requires modifications to the CDB5326/7/8/9 to derive the proper clock frequencies. This is done by utilizing a 12.288 MHz clock and supplying a clock to the CDB5326/7/8/9 at 6.144 MHz. CDB4328 Configuration The CS4328 must be set to receive data in format 2 (DIF1 high and DIF0 low). Modify the jumpers located near pins 12 and 13 of the CS4328. JP2 sets the clock to sample frequency ratio (CKS) on the CS4328 and is set low for a 256 ratio. JP3 selects the source of SDATA, SCLK and L/R that will be provided to the converter and should DS62DB2 27 CDB4328 Figure 4. Top Ground Plane Layer (NOT TO SCALE) 28 DS62DB2 CDB4328 Figure 5. Bottom Trace Layer (NOT TO SCALE) DS62DB2 29 CDB4328 Figure 5. Silk Screen Layer (NOT TO SCALE) 30 DS62DB2 • Notes • Smart AnalogTM is a Trademark of Crystal Semiconductor Corporation