HS2AA THRU HS2MA 1.5 AMPS. High Efficient Surface Mount Rectifiers Voltage Range 50 to 1000 Volts Current 1.5 Amperes SMA/DO-214AC Features Glass passivated junction chip. For surface mounted application Low forward voltage drop Low profile package Built-in stain relief, ideal for automatic placement Fast switching for high efficiency High temperature soldering: 260℃/10 seconds at terminals Plastic material used carries Underwriters Laboratory Classification 94V-O .062(1.58) .050(1.27) .111(2.83) .090(2.29) .187(4.75) .160(4.06) .091(2.30) .078(1.99) .012(.31) .006(.15) Mechanical Data Cases: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Packing: 12mm tape per EIA STD RS-481 Weight: 0.064 gram .008(.20) .004(.10) .056(1.41) .035(0.90) .210(5.33) .195(4.95) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol HS HS HS Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current See Fig. 2 Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.5A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) VRRM VRMS VDC HS HS HS HS HS Units 2AA 2BA 2DA 2FA 2GA 2JA 2KA 2MA 50 100 200 300 400 600 800 1000 V 35 70 140 210 280 420 560 700 V 50 100 200 300 400 600 800 1000 V I(AV) 1.5 A IFSM 50 A 1.0 VF 1.3 5.0 100 IR 50 50 Trr Cj RθJA TJ 90 -55 to +150 Storage Temperature Range TSTG -55 to +150 Notes: 1. Reverse Recovery Test Conditions: I F=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied VR=4.0 Volts 3. Mounted on P.C.B. with 0.2”x0.2” ( 5 x 5 mm ) Copper Pad Areas. Maximum Thermal Resistance ( Note 3 ) Operating Temperature Range 1.7 - 308 - 75 30 V uA uA nS pF ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (HS2AA THRU HS2MA) FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 10W NONINDUCTIVE trr AVERAGE FORWARD CURRENT. (A) 50W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) 0 PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm SET TIME BASE FOR 5/ 10ns/ cm SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTH 2.5 2.0 1.5 1.0 0.5 0 0 25 50 75 100 125 150 175 o LEAD TEMPERATURE. ( C) FIG.4- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.3- TYPICAL REVERSE CHARACTERISTICS 10 10 Tj=25 0C HS 2G A 0.1 0.01 HS2J A-HS 1 1 2MA Tj=100 0C 100 HS2 AA-H S2D A INSTANTANEOUS FORWARD CURRENT. (A) 1000 INSTANTANEOUS REVERSE CURRENT. ( A) 3.0 0.1 0.001 0 20 40 60 80 100 120 0 140 0.2 0.4 70 175 60 150 8.3ms Single Half Sine Wave JEDEC Method 40 30 20 1.0 1.2 1.4 125 HS 100 HS 2 2AA JA- 75 -HS HS 2 2G A MA 50 25 10 0 1 0.8 FIG.6- TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE.(pF) PEAK FORWARD SURGE CURRENT. (A) FIG.5- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 0.6 FORWARD VOLTAGE. (V) PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 2 5 10 20 NUMBER OF CYCLES AT 60Hz 50 100 - 309 - 0 0.1 0.5 1 2 5 10 20 50 REVERSE VOLTAGE. (V) 100 200 500 1000