Click on Series name for product info on aimtec.com Series AM2B-NZ 2 Watt | DC-DC Converter FEATURES: 6000 VDC Isolation Low Profile DIP 16 Package Industry Standard Pinout MTBF>3,500,000 hours Unregulated Single Output Models Operating Temperature: -40°C to +105°C High Efficiency up to 81% RoHS Compliant Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Efficiency (%) AM2B-0505SH60-NZ 4.5-5.5 5 400 6000 77 AM2B-0512SH60-NZ 4.5-5.5 12 167 6000 81 AM2B-0515SH60-NZ 4.5-5.5 15 133 6000 80 AM2B-1205SH60-NZ 10.8-13.2 5 400 6000 77 *AM2B-1215SH60-NZ 10.8-13.2 15 133 6000 81 AM2B-2405SH60-NZ 21.6-26.4 5 400 6000 78 AM2B-2415SH60-NZ 21.6-26.4 15 133 6000 80 *Not recommended for new design NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Nominal Typical 5 12 24 4.5-5.5 10.8-13.2 21.6-26.4 Conditions Typical Maximum Units VDC Isolation Specifications Parameters Tested I/O voltage Capacitance Resistance 60 sec 500VDC Rated Units 6000 VDC pF MOhm 10 >1000 Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy See Tolerance Graph ±5 % Short circuit protection Continuous Short Circuit restart Auto Recovery Line voltage regulation For a 1% change of Vin ±1.2 % Load voltage regulation From 10% load to 100% load 12 % Temperature coefficient At 100% load ±0.03 %/oC Ripple & Noise* 20MHz Bandwidth 150 mV p-p Minimum load current** 10 % of Max * Test ripple & noise by “Parallel Cable Method” as described in Application Note “Ripple and Noise Measurement of Brick & POL DC-DC Converters” available at www.aimtec.com ** If the operating output current is less than 10% of maximum it is recommended to install a load resister in parallel with the load to ensure the actual load current meets the minimum load current requirement. www.aimtec.com F 051e R12.G Tel: +1 514 620 2722 1 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM2B-NZ 2 Watt | DC-DC Converter General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Conditions Typical 100% load, nominal input 50 ‡ Maximum Units 100 KHz oC oC oC 95 % RH -40 to + 85 ‡ -55 to + 125 Free Air Convection Plastic(UL94-V0) 3.8 0.94 x 0.60 x 0.32 inches 23.86 x 15.24 x 8.00mm > 3,500,000 hours (MIL-HDBK -217F, Ground Benign, t=+25ºC) 1.5mm from case for 10 seconds 300 g oC Safety Specifications Parameters Agency approvals Standards Pin Out Specifications Pin CE EN 60601-1-1; EN 60601-1-2 Load Accuracy Tolerance Graph Single 1 - V in 2 No Pin 3 No Pin 4 No Pin 5 No Pin 6 No Pin 7 NC 8 NC 9 +V out 10 -V out 11 No Pin 12 No Pin 13 No Pin 14 No Pin 15 No Pin 16 +V in NC: not connected www.aimtec.com F 051e R12.G Tel: +1 514 620 2722 2 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM2B-NZ 2 Watt | DC-DC Converter Typical Efficiency Example Charts Eff % AM2B‐0505S‐NZ Efficiency vs. Loading 100 90 80 70 60 50 40 30 20 10 0 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 90% 100% 90% 100% Loading % Eff % AM2B‐1205S‐NZ Efficiency vs. Loading 100 90 80 70 60 50 40 30 20 10 0 10% 20% 30% 40% 50% 60% 70% 80% Loading % Eff % AM2B‐2412S‐NZ Efficiency vs. Loading 100 90 80 70 60 50 40 30 20 10 0 10% 20% 30% 40% 50% 60% 70% 80% Loading % www.aimtec.com F 051e R12.G Tel: +1 514 620 2722 3 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM2B-NZ 2 Watt | DC-DC Converter Dimensions Top View 16 15.24 (0.60) Bottom View 10 1 9 13.70 (0.54) 8 10 9 Bottom View 7 1 16 8 15.24 (0.60) 2.54 (0.10) 2.54 (0.10) Side View Front View 23.86 (0.94) 8.00 (0.32) 7 7.50 (0.30) 13.10 (0.52) 15.24 (0.60) 3.00 (0.20) Derating Free Air Convection 100 ºC Output Power % 100 80 60 Safe Operating Area 40 20 105 0 -40 -20 0 20 40 60 80 100 Ambient Temperature º C www.aimtec.com F 051e R12.G Tel: +1 514 620 2722 4 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM2B-NZ 2 Watt | DC-DC Converter Recommended Filter Circuit L Single Output L +Vout + Vin + Cin + DC DC - Vin Cout - Vin If it is required to decrease the input/output ripple an “LC” filter network can be installed on the input and output of the converter (see above). It should be noted that the inductance and the resonant frequency of the “LC” filtering network should differ from the DC/DC converter switching frequency to avoid mutual interference. The capacitance of the output filter capacitor must not exceed the values in the Table below to avoid startup problems and ensure safe and reliable operation. It’s not recommended to connect any external capacitor in the application field when output loading is less than 0.5 watt. External Capacitor Tables Input Capacitor (Cin) Vin (VDC) Cin (uF) 5 12 24 4.7 2.2 1 Output Capacitor (Cout) Single Vout (VDC) 5 12 15 Cout (uF) 10 2.2 1 NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.G Tel: +1 514 620 2722 5 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only