3.0x2.5mm SURFACE MOUNT LED LAMP Part Number: APBL3025SRQGCPR-F01 Super Bright Red Green Features Descriptions 3.0mmx2.5mm SMT LED, 1.4mm thickness. The Super Bright Red source color devices are made with Gallium Aluminum Arsenide Red Light Emitting Diode. Low power consumption. The Green source color devices are made with Gallium Wide viewing angle. Ideal for back light and indicator. Phosphide Green Light Emitting Diode. Inner lens type. Moisture sensitivity level : level 3. Package : 2000pcs / reel. RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAF1333 REV NO: V.5A DATE: FEB/07/2015 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203000916 Selection Guide Part No. Dice Iv (mcd) [2] @ 20mA Lens Type Viewing Angle [1] Min. Typ. 100 150 *20 *50 12 20 *12 *20 2θ1/2 Super Bright Red (GaAlAs) APBL3025SRQGCPR-F01 100° Water Clear Green (GaP) Notes: 1.θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2.Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Red Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 655 560 nm IF=20mA Super Bright Red Green 640 565 nm IF=20mA Spectral Line Half-width Super Bright Red Green 20 30 nm IF=20mA C Capacitance Super Bright Red Green 45 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Red Green 1.85 2.15 2.5 2.5 V IF=20mA IR Reverse Current Super Bright Red Green 10 10 uA VR = 5V Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Red Green Units Power dissipation 75 62.5 mW DC Forward Current 30 25 mA Peak Forward Current [1] 155 130 mA Reverse Voltage 5 V Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAF1333 REV NO: V.5A DATE: FEB/07/2015 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203000916 APBL3025SRQGCPR-F01 Super Bright Red SPEC NO: DSAF1333 REV NO: V.5A DATE: FEB/07/2015 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203000916 Green SPEC NO: DSAF1333 REV NO: V.5A DATE: FEB/07/2015 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203000916 APBL3025SRQGCPR-F01 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAF1333 REV NO: V.5A DATE: FEB/07/2015 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203000916 PACKING & LABEL SPECIFICATIONS APBL3025SRQGCPR-F01 Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF1333 REV NO: V.5A DATE: FEB/07/2015 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.M.Chen ERP: 1203000916