ASL390 Wideband Linear Amplifier MMIC Features Description 23.3 dB Gain at 500 MHz The ASL390, a wideband linear amplifier MMIC, has a high linearity and low noise over a wide range of frequency 5 MHz to 1.2 GHz, being suitable for use in the fiber receiver, distribution amplifiers and drop amplifiers of CATV systems, and in the mobile wireless repeaters and BTS. The amplifier is available in a SOT89 package and passes through the stringent DC, RF, and reliability tests. 22 dBm P1dB at 500 MHz 42 dBm Output IP3 at 500 MHz 75 Input & Output Match Bandwidth 5 ~ 1200 MHz Single Supply ASL390 Package Style: SOT89 Typical Performance (Supply Voltage = +5 V, TA = +25 C, Z0 = 75 ) Applications Parameters Units Typical Frequency MHz 5 50 500 860 Noise Figure dB 3.1 2.3 2.3 2.5 5 ~ 200 MHz (3.3 V) Gain dB 23.3 23.8 23.3 22.1 5 ~ 200 MHz S11 dB -15.0 -15.0 -20.0 -16.5 S22 dB -16.0 -18.0 -18.0 -15.5 dBm 18.5 22.0 22.0 19.5 Output P1dB Output IP3 1) 1) 2) 2) 2) dBm 37.5 39.0 42.0 41.0 Output IP21),3) dBm 521), 3) 492), 3) 502), 3) 502), 3) CSO4) dBc 66 / 60 CTB4) dBc 75 / 69 Supply Current mA 120 120 Device Voltage V +5 +5 50 ~ 1000 MHz 50 ~ 1200 MHz 50 ~ 1000 MHz (Push-Pull, 1:1 transformer) 50 ~ 1000 MHz (3.3 V) 1) OIP3 and OIP2 are measured with two tones at an output power of +7 dBm/tone separated by 1 MHz. 2) OIP3 and OIP2 are measured with two tones at an output power of +9 dBm/tone separated by 6 MHz. 3) OIP2 is measured at F1+F2 Frequency. 4) Pout=95 dBuV / 98 dBuV for 84 channels VHF signal. Product Specifications Parameters Units Testing Frequency MHz Min. Typ. Max. Gain dB S11 dB -20 -16 S22 dB -18 -15 Output IP3 dBm Noise Figure dB Output P1dB dBm Supply Current mA Device Voltage V 500 22.3 39 23.3 42 2.3 2.7 21 22 22 100 120 140 Pin Configuration +5 Absolute Maximum Ratings Parameters Rating Operating Case Temperature -40 to 85 C Pin No. Function Storage Temperature -40 to 150 C 1 RF IN Device Voltage +7 V 2 GND Operating Junction Temperature +150 C Input RF Power (CW, 75 matched)* +24 dBm 3 RF OUT & Bias Thermal Resistance 42 C/W * Please find the max. input power data from http://www.asb.co.kr/pdf/Maximum_Input_Power_Analysis.pdf 1/10 ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017 ASL390 Wideband Linear Amplifier MMIC Outline Drawing Part No. Lot No. Symbols A L b b1 C D D1 E E1 e1 H S e ASL390 Pxxxx Dimensions (In mm) MIN NOM 1.40 1.50 0.89 1.04 0.36 0.42 0.41 0.47 0.38 0.40 4.40 4.50 1.40 1.60 3.64 --2.40 2.50 2.90 3.00 0.35 0.40 0.65 0.75 1.40 1.50 Pin No. Function 1 RF IN 2 GND 3 RF OUT & Bias MAX 1.60 1.20 0.48 0.53 0.43 4.60 1.75 4.25 2.60 3.10 0.45 0.85 1.60 Mounting Recommendation (In mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of the lead pin 2 and exposed pad of the device for better RF and thermal performance, as shown in the drawing at the left side. ESD Classification & Moisture Sensitivity Level ESD Classification HBM Class 1B Voltage Level: 550 V MM Class A Voltage Level: 50 V CAUTION: ESD-sensitive device! Moisture Sensitivity Level (MSL) Level 3 at 260 C reflow 2/10 ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017 ASL390 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV Frequency (MHz) 5 50 200 Noise Figure (dB) 2.4 2.4 2.0 Magnitude S21 (dB) 23.3 23.4 23.0 Magnitude S11 (dB) -12 -16 -17 Magnitude S22 (dB) -16 -20 -20 Output P1dB (dBm) 14 18 18 Output IP3 (dBm) 30 34 35 Output IP21),2) (dBm) 48 43 43 Device Voltage (V) +3.3 Current (mA) 68 1) 5 ~ 200 MHz +3.3 V 1) OIP3 and OIP2 are measured with two tones at an output power of +3 dBm/tone separated by 1 MHz. 2) OIP2 is measured at F1+F2 Frequency. Vs=3.3 V Schematic Board Layout (FR4, 40x40 mm2, 0.8T) C3=10 F L1=22 H (LQH32MN220J23) C2=1 F C1=1 nF RF IN RF OUT ASL390 L2=4.7 H R1=150 30 0 25 -5 20 -10 S11 (dB) Gain (dB) S-parameters 15 -15 10 -20 5 -25 0 -30 0 50 100 150 200 0 50 100 150 200 Frequency (MHz) Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 -30 0 50 100 150 200 Frequency (MHz) 3/10 ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017 ASL390 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV Frequency (MHz) 5 50 200 Noise Figure (dB) - 2.3 2.3 Magnitude S21 (dB) 23.2 23.7 23.5 Magnitude S11 (dB) -20 -18 -20 Magnitude S22 (dB) -19 -20 -20 Output P1dB (dBm) 17.5 21.0 21.0 Output IP3 (dBm) 34.0 41.0 41.5 Output IP21),2) (dBm) 55 54 51 Device Voltage (V) +5 Current (mA) 120 1) 5 ~ 200 MHz +5 V 1) OIP3 and OIP2 are measured with two tones at an output power of +3/+9 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. Schematic Board Layout (FR4, 40x40 mm2, 0.8T) Vdevice=+5 V C3=10 F L1=22 H (LQH32MN220J23) C2=1 F C1=10 nF RF IN RF OUT ASL390 L2=3.3 H L3=3.3 H R1=150 R2=330 30 0 25 -5 20 -10 S11 (dB) Gain (dB) S-parameters 15 -15 10 -20 5 -25 -30 0 0 50 100 Frequency (MHz) 150 0 50 100 Frequency (MHz) 150 200 0 50 100 Frequency (MHz) 150 200 0 -5 S22 (dB) -10 -15 -20 -25 -30 4/10 200 ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017 ASL390 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV Frequency (MHz) 50 500 860 Noise Figure (dB) 2.3 2.3 2.5 Magnitude S21 (dB) 23.8 23.3 22.1 Magnitude S11 (dB) -15.0 -20.0 -16.5 Magnitude S22 (dB) -18.0 -18.0 -15.5 Output P1dB (dBm) 22.0 22.0 19.5 Output IP3 (dBm) 39 42 41 Output IP21),2) (dBm) 49 50 50 1) 50 ~ 1000 MHz +5 V 3) CSO (dBc) 66, 60 CTB3) (dBc) 75, 69 Device Voltage (V) +5 Current (mA) 120 1) OIP3 and OIP2 are measured with two tones at an output power of +9 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. 3) Pout=95 dBuV / 98 dBuV for 84 channels VHF signal Schematic Board Layout (FR4, 40x40 mm2, 0.8T) Vs=5 V C4=10 uF L1=1 H (LQH31CN1R0M03) C1=1 F RF IN L2=12 nH C2=1 F RF OUT ASL390 C3=1 pF S-parameters 30 0 25 -5 o -40 c o 25 c o 85 c -10 20 15 S11 (dB) Gain (dB) o -40 c o 25 c o 85 c -15 10 -20 5 -25 -30 0 0 100 200 300 400 500 600 700 800 900 1000 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Frequency (MHz) 0 -5 o -40 c o 25 c o 85 c -10 S22 (dB) -15 -20 -25 -30 -35 -40 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 5/10 ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017 ASL390 Wideband Linear Amplifier MMIC Gain vs. Temperature 140 25 130 24 120 23 Gain (dB) Current (mA) Current vs. Temperature 110 22 Frequency = 860 MHz 21 100 90 -60 -40 -20 0 20 40 60 80 20 -60 100 -40 -20 0 20 40 60 80 100 o Temperature ( C) o Temperature ( C) P1dB vs. Temperature NF vs. Temperature 2.8 24 2.6 22 2.4 NF (dB) P1dB (dBm) 2.2 20 18 2.0 1.8 1.6 Frequency = 860 MHz 16 Frequency = 500 MHz 1.4 1.2 14 -60 -40 -20 0 20 40 60 80 100 1.0 -60 -40 -20 0 20 40 60 80 100 o o Temperature ( C) Temperature ( C) NF vs. Frequency 3.00 2.75 NF (dB) 2.50 2.25 2.00 1.75 1.50 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 Frequency (GHz) Output IP3 vs. Tone Power (Frequency = 860 MHz) Output IP2 vs. Tone Power (Frequency = 860 MHz) MHz) 50 60 o o -40 c o 25 c o 85 c -40 c o 25 c o 85 c 55 40 Output IP2 (dBm) Output IP3 (dBm) 45 35 30 50 45 40 35 25 30 20 7 8 9 10 11 12 13 14 15 7 8 6/10 9 10 11 12 13 14 15 Pout per Tone (dBm) Pout per Tone (dBm) ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017 ASL390 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV 50 ~ 1200 MHz Frequency (MHz) 50 500 860 1200 Noise Figure (dB) 3.2 2.5 2.5 2.5 Magnitude S21 (dB) 23.0 22.8 22.8 21.2 Magnitude S11 (dB) -16.0 -13.0 -13.0 -12.0 Magnitude S22 (dB) -14.5 -16.0 -15.0 -17.0 Output P1dB (dBm) 23.0 21.0 19.5 19.5 Output IP31) (dBm) 41.0 42.5 40.0 41.0 52 55 46 53 Output IP2 +5 V 1),2) (dBm) Device Voltage (V) +5 Current (mA) 120 1) OIP3 and OIP2 are measured with two tones at an output power of +9 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. Schematic Board Layout (FR4, 40x40 mm2, 0.8T) Vdevice=+5 V C5=10 F L1=1 H (LQH31CN1R0M03) R1=16 RF IN C1=1 F L2=6.8 nH L3=5.6 nH C2=1 F RF OUT ASL390 C3=1 pF C4=33 pF S-parameters 0 30 25 S11 (dB) Gain (dB) -5 20 15 -10 10 -15 5 0 -20 0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200 Frequency (MHz) Frequency (MHz) 0 S22 (dB) -5 -10 -15 -20 0 200 400 600 800 1000 1200 Frequency (MHz) 7/10 ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017 ASL390 Wideband Linear Amplifier MMIC Frequency (MHz) 50 500 860 Noise Figure (dB) 3.2 2.6 2.5 Magnitude S21 (dB) 19.2 18.6 17.8 Magnitude S11 (dB) -17 -13 -14 CATV Push-Pull Magnitude S22 (dB) -17 -11 -13 1 : 1 transformer Output P1dB (dBm) 25 26 26 Output IP3 (dBm) 39 43 42 Output IP21) (dBm) 70 63 56 CSO (dBc)2) 66 CTB (dBc) 2) 63 Device Voltage (V) +5 Current (mA) 240 APPLICATION CIRCUIT 1) 50 ~ 1000 MHz +5 V . 1) OIP3 and OIP2 are measured with two tones at an output power of +9 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. 3) Pout=102.5 dBuV for 60 channels VHF signal. Vs=5 V Schematic Board Layout (FR4, 40x40 mm2, 0.8T) Note: MABA-007159 1:1 impedance transformers are used. C5=10 uF L1=1 uH (LQH31CN1R0M03) C1=1 uF C2=1 uF ASL390 RF OUT C4=1 uF 1:1 transformer RF IN C3=0.5 pF 1:1 transformer R1=820 C6=1 uF C7=1 uF ASL390 C9=1 uF C8=0.5 pF L2=1 uH (LQH31CN1R0M03) R2=820 C10=10 uF Vs=5 V 30 0 25 -5 20 -10 S11 (dB) Gain (dB) S-parameters 15 -15 10 -20 5 -25 0 -30 0 100 200 300 400 500 600 700 800 900 1000 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Frequency (MHz) 0 -5 S22 (dB) -10 -15 -20 -25 -30 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 8/10 ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017 ASL390 Wideband Linear Amplifier MMIC APPLICATION CIRCUIT CATV 50 ~ 1000 MHz Frequency (MHz) 50 500 860 Noise Figure (dB) 2.0 2.2 2.4 Magnitude S21 (dB) 23.6 22.9 21.7 Magnitude S11 (dB) -15.0 -18.0 -14.0 Magnitude S22 (dB) -18.0 -18.0 -14.0 Output P1dB (dBm) 18.0 18.0 17.5 Output IP31) (dBm) 37.0 35.5 33.0 50 47 42 Output IP2 +3.3 V 1),2) (dBm) Device Voltage (V) +3.3 Current (mA) 74 1) OIP3 and OIP2 are measured with two tones at an output power of +4 dBm/tone separated by 6 MHz. 2) OIP2 is measured at F1+F2 Frequency. Schematic Board Layout (FR4, 40x40 mm2, 0.8T) Vs=5 V C4=10 uF L1=1 H (LQH31CN1R0M03) C1=1 F RF IN L2=12 nH C2=1 F RF OUT ASL390 C3=1 pF 30 0 25 -5 20 -10 S11 (dB) Gain (dB) S-parameters 15 -15 10 -20 5 -25 0 0 100 200 300 400 500 600 Frequency (MHz) 100 200 300 400 500 600 Frequency (MHz) 700 800 900 1000 -30 0 100 200 300 400 500 600 Frequency (MHz) 700 800 900 1000 0 -5 -10 S22 (dB) -15 -20 -25 -30 -35 -40 0 9/10 700 800 900 1000 ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017 ASL390 Wideband Linear Amplifier MMIC Recommended Soldering Reflow Profile 260 C Ramp-up (3 C/sec) 20~40 sec Ramp-down (6 C/sec) 200 C 150 C 60~180 sec Copyright 2012-2017 ASB Inc. All rights reserved. Datasheet subject to change without notice. ASB assumes no responsibility for any errors which may appear in this datasheet. No part of the datasheet may be copied or reproduced in any form or by any means without the prior written consent of ASB. 10/10 ASB Inc. [email protected] Tel: +82-42-528-7225 April 2017