10A005 THRU 10A10 10.0 AMP SILICON RECTIFIERS VOLTAGE RANGE 50 TO 1000 Volts CURRENT 10.0 Amperes FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability R-6 .360(9.1) .340(8.6) DIA. 1.0(25.4) MIN. MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Axial leads, solderable per MIL-STD-202, method 208 guranteed * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 1.65 grams .360(9.1) .340(8.6) 1.0(25.4) MIN. .052(1.3) .048(1.2) DIA. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current 10A05 10A1 10A2 10A4 10A6 10A8 10A10 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 UNITS V V V .375"(9.5mm) Lead Length at Ta=60 C Peak Forward Surge Current, 8.3 ms single half sine-wave 10.0 A superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 10.0A Maximum DC Reverse Current Ta=25 C 400 A V µA 1.0 10.0 at Rated DC Blocking Voltage Ta=100 C Typical Junction Capacitance (Note 1) Typical Thermal Resistance RθJA (Note 2) Operating and Storage Temperature Range TJ, TSTG 400 100 10 -65 NOTES: 1. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 2. Thermal Resistance from Junction to Ambient .375" (9.5mm) lead length. 128 +150 µA pF C/W C RATING AND CHARACTERISTIC CURVES (10A005 THRU 10A10) FIG.1-TYPICAL FORWARD FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) 12 100 40 10 10 8 Single Phase 6 Half Wave 60Hz Resistive Or Inductive Load 4 0.375"(9.5mm) Lead Length 2 0 0 20 40 60 80 100 120 140 160 180 200 Tj=25 C AMBIENT TEMPERATURE,( C) Pulse Width 300us 1% Duty Cycle 1 .6 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE,(V) FIG.3 - TYPICAL REVERSE CHARACTERISTICS PEAK FORWARD SURGE CURRENT,(A) INSTANTANEOUS FORWARD CURRENT,(A) 500 500 400 300 8.3ms Single Half Tj=25 C Sine Wave 200 JEDEC method 100 0 100 1 5 50 10 100 NUMBER OF CYCLES AT 60Hz Tj=100 C FIG.5 - TYPICAL THERMAL RESISTANCE VS. LEAD LENGTH 1.0 Tj=25 C .1 .01 0 THERMAL RESISTANCE, ( C/W) REVERSE LEAKAGE CURRENT, ( µA) 10 20 40 60 80 100 120 140 25 20 15 10 5 0 .1 .2 .3 .4 .5 .6 .7 .8 .9 EQUAL LEAD LENGTH TO HEAT SINK, INCHES PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) 129 1.0