Holtek HT85F2240 A/d flash 8051 core low pin count mcu Datasheet

A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Revision: V1.10
Date: ��
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Table of Contents
1 Features.................................................................................................................. 11
CPU Features.................................................................................................................... 11
Peripheral Features............................................................................................................ 12
3 Selection Table....................................................................................................... 14
4 Block Diagram........................................................................................................ 15
5 Pin Assignment...................................................................................................... 16
6 Pin Descriptions.................................................................................................... 17
7 Absolute Maximum Ratings.................................................................................. 19
8 D.C. Characteristics............................................................................................... 19
9 A.C. Characteristics............................................................................................... 21
10 ADC Electrical Characteristics........................................................................... 22
11 Comparator Electrical Characteristics............................................................... 23
12 Power on Reset Electrical Characteristics........................................................ 24
13 System Architecture............................................................................................ 24
14 Program Counter................................................................................................. 25
15 Stack..................................................................................................................... 25
16 Arithmetic and Logic Unit – ALU........................................................................ 26
17 Flash Program Memory....................................................................................... 27
Structure............................................................................................................................. 27
Special Vectors.................................................................................................................. 27
In-Circuit Programming – ICP............................................................................................ 28
On-Chip Debug Support – OCDS...................................................................................... 28
In-Application Programming – IAP..................................................................................... 29
Flash Program Memory Resisters...................................................................................... 29
Flash Memory Read/Write Operations............................................................................... 33
Unlocking the Flash Memory......................................................................................................... 33
Page Erase Operation................................................................................................................... 34
Byte Read Operation..................................................................................................................... 35
Byte Write Operation..................................................................................................................... 36
Program Memory Protection.............................................................................................. 38
Memory Protection Control Bytes.................................................................................................. 38
Rev. 1.10
2 of 147
July 31, 2015
Table of Contents
2 General Description .............................................................................................. 13
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
18 RAM Data Memory............................................................................................... 41
Structure............................................................................................................................. 41
Register Banks................................................................................................................... 44
Bit Addressable Space....................................................................................................... 44
Special Function Registers................................................................................................ 46
19 Oscillators............................................................................................................ 51
System Oscillator Overview............................................................................................... 51
System Clock Configuration............................................................................................... 51
External High Speed Crystal Oscillator – HXT.............................................................................. 51
Internal High Speed RC Oscillator – HIRC.................................................................................... 52
Internal Low Speed RC Oscillator – LIRC..................................................................................... 52
20 Operating Modes and System Clocks............................................................... 53
System Clocks Description................................................................................................ 53
Operation Modes................................................................................................................ 57
NORMAL Mode............................................................................................................................. 58
IDLE Mode.................................................................................................................................... 58
Power - Down Mode...................................................................................................................... 58
Power Control Register...................................................................................................... 58
Standby Current Considerations........................................................................................ 59
Wake-up............................................................................................................................. 59
21 Watchdog Timer................................................................................................... 60
Watchdog Registers........................................................................................................... 61
Watchdog Timer Clock Source........................................................................................... 64
Watchdog Timer Operation................................................................................................ 64
22 Low Voltage Detector – LVD............................................................................... 66
LVD Register...................................................................................................................... 66
LVD Operation.................................................................................................................... 66
Rev. 1.10
3 of 147
July 31, 2015
Table of Contents
ACC Register – Accumulator......................................................................................................... 47
B Register ..................................................................................................................................... 47
SP Register – Stack Pointer.......................................................................................................... 47
DPL, DPH, DPL1, DPH1 Registers – Data Pointer Registers....................................................... 47
Data Pointer Select Registers....................................................................................................... 48
Data Pointer Control Register....................................................................................................... 48
Program Status Word.................................................................................................................... 50
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
23 Reset and Initialisation........................................................................................ 67
Reset Overview.................................................................................................................. 67
Reset Operations............................................................................................................... 68
Reset Initial Conditions...................................................................................................... 74
24 Interrupts.............................................................................................................. 79
Interrupt Registers.............................................................................................................. 79
Interrupt Operation............................................................................................................. 85
Interrupt Priority.................................................................................................................. 86
Priority Levels................................................................................................................................ 86
Priority Control Registers.............................................................................................................. 87
External Interrupt................................................................................................................ 90
A/D Converter Interrupt...................................................................................................... 90
Timer/Counter Interrupt...................................................................................................... 90
Time Base Interrupts.......................................................................................................... 91
LVD Interrupt...................................................................................................................... 92
Interrupt Wake-up Function................................................................................................ 93
Programming Considerations............................................................................................. 93
25 Input/Output Ports............................................................................................... 94
Input/Output Port Overview................................................................................................ 94
Register Description........................................................................................................... 95
PnM0/PnM1 Registers – Port Mode Registers.............................................................................. 96
P0WAKE Register – Port 0 Wake-up............................................................................................ 98
SRCR Register – Slew Rate Control............................................................................................. 99
Pin-remapping Function..................................................................................................... 99
PRM Register – Pin-remapping Control Register.......................................................................... 99
I/O Pin Structures............................................................................................................. 100
Quasi-bidirectional I/O ................................................................................................................ 100
Push-pull Output ......................................................................................................................... 101
Open-drain Output ...................................................................................................................... 101
Input Only ................................................................................................................................... 101
Programming Considerations........................................................................................... 102
Rev. 1.10
4 of 147
July 31, 2015
Table of Contents
Reset Source Register – RSTSRC............................................................................................... 68
Power-on Reset............................................................................................................................. 69
RESET Pin Reset.......................................................................................................................... 70
Low Voltage Reset – LVR.............................................................................................................. 71
Watchdog Reset ........................................................................................................................... 72
Software Resets............................................................................................................................ 72
SRST Register Software Reset..................................................................................................... 73
WDTCR Register Software Reset................................................................................................. 73
LVRCR Register Software Reset................................................................................................... 74
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
26 Timer/Event Counters....................................................................................... 103
Timer/Event Counter Summary........................................................................................ 103
27 Timer/Event Counters 0, 1................................................................................ 104
Introduction...................................................................................................................... 104
Timer 0/Timer 1Register Description................................................................................ 104
Mode 1 – 16-bit Counter/Timer Mode Operation.............................................................. 110
Mode 2 – 8-bit Auto-reload Counter/Timer Mode Operation.............................................111
Mode 3 – Two 8-Bit Timers/Counters Mode Operation – Timer 0 Only............................ 112
28 Timer 2 with Additional 2-channel PCA........................................................... 113
Introduction...................................................................................................................... 113
Timer 2............................................................................................................................. 114
Timer function...............................................................................................................................114
Event Counter function.................................................................................................................114
Gated Timer function....................................................................................................................115
Timer 2 with PCA.............................................................................................................. 115
Timer 2 Register Description............................................................................................ 116
Capture Modes................................................................................................................. 118
Capture On Edge Mode...............................................................................................................118
Capture On Write Mode................................................................................................................118
Compare Modes............................................................................................................... 119
Compare Mode 0..........................................................................................................................119
Compare Mode 1......................................................................................................................... 120
Reload Mode.................................................................................................................... 122
Programmable Clock Output Mode.................................................................................. 123
29 Analog to Digital Converter – ADC .................................................................. 124
A/D Overview................................................................................................................... 124
A/D Converter Register Description................................................................................. 125
A/D Converter Data Registers – ADRL, ADRH................................................................ 125
A/D Converter Control Registers – ADCR0, ADCR1, ADCR2, ADPGA........................... 125
A/D Operation.................................................................................................................. 129
A/D Converter Clock Source............................................................................................ 130
A/D Input Pins.................................................................................................................. 130
Temperature Sensor......................................................................................................... 131
A/D Reference Voltage Source........................................................................................ 131
Summary of A/D Conversion Steps.................................................................................. 132
A/D Conversion Timing.................................................................................................... 133
Programming Considerations........................................................................................... 133
A/D Transfer Function...................................................................................................... 134
Rev. 1.10
5 of 147
July 31, 2015
Table of Contents
Mode 0 – 13-bit Counter/Timer Mode Operation.............................................................. 109
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
30 Voltage Reference Generator........................................................................... 135
Voltage Reference Generator Operation.......................................................................... 135
31 Instruction Set.................................................................................................... 136
Introduction...................................................................................................................... 136
Read-Modify-Write Instruction.......................................................................................... 141
20-pin SOP (300mil) Outline Dimensions......................................................................... 143
20-pin SSOP (150mil) Outline Dimensions...................................................................... 144
24-pin SOP (300mil) Outline Dimensions......................................................................... 145
24-pin SSOP (150mil) Outline Dimensions...................................................................... 146
Rev. 1.10
6 of 147
July 31, 2015
Table of Contents
32 Package Information......................................................................................... 142
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
List of Tables
Rev. 1.10
7 of 147
July 31, 2015
List of Tables
Program Memory Register List................................................................................................................. 29
FMAR0 Register – Flash Program Memory Address Register 0.............................................................. 29
FMAR1 Register – Flash Program Memory Address Register 1.............................................................. 30
FMAR2 Register – Flash Program Memory Address Register 2.............................................................. 30
FMDR Register – Flash Program Memory Data Register ....................................................................... 30
FMCR Register – Flash Program Memory Control Register ................................................................... 31
FMKEY Register – Flash Program Memory Unlock Key Data Register .................................................. 32
FMSR Register – Flash Program Memory Status Register ..................................................................... 32
HT85F2240 Program Memory Contents................................................................................................... 39
HT85F2230 Program Memory Contents................................................................................................... 39
Security Bytes........................................................................................................................................... 40
General Purpose Data RAM, 20H~2FH, Bit Address Map....................................................................... 44
Special Function Register Bit Addresses Map.......................................................................................... 45
Special Function Register Map................................................................................................................. 46
DPS Register – Data Pointer Select Register........................................................................................... 48
DPC Register – Data Pointer Control Register......................................................................................... 49
PSW Register – Program Status Word Register...................................................................................... 50
Crystal Recommended Capacitor Values................................................................................................. 52
System Clock Control Register – SCCR................................................................................................... 55
High Speed Oscillator Control Register – HSOCR................................................................................... 56
HIRC Frequency Select Control Register – HFSCR................................................................................. 56
Low Speed Oscillator Control Register – LSOCR.................................................................................... 57
PCON Register – Power Control Register................................................................................................ 58
WDT Register Contents............................................................................................................................ 61
IEN0 Register........................................................................................................................................... 61
IEN1 Register........................................................................................................................................... 62
WDTREL Register.................................................................................................................................... 62
WDTCR Register...................................................................................................................................... 63
IP0 Register.............................................................................................................................................. 63
Watchdog Timer Enable/Disable Control.................................................................................................. 64
LVDCR Register ...................................................................................................................................... 66
Reset Source Summary............................................................................................................................ 67
RSTSRC Register..................................................................................................................................... 68
LVRCR Register ...................................................................................................................................... 71
IP0 Register.............................................................................................................................................. 72
T2CON1 Register..................................................................................................................................... 73
Software Reset Summary......................................................................................................................... 73
SRST Register.......................................................................................................................................... 74
WDTCR Register...................................................................................................................................... 74
LVRCR Register....................................................................................................................................... 75
Interrupt Register Bit Naming Conventions.............................................................................................. 80
Interrupt Register Contents....................................................................................................................... 80
IEN0 Register .......................................................................................................................................... 81
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Rev. 1.10
8 of 147
July 31, 2015
List of Tables
IEN1 Register........................................................................................................................................... 81
IEN2 Register .......................................................................................................................................... 82
IEN3 Register........................................................................................................................................... 82
IRCON Register........................................................................................................................................ 83
T2CON Register ...................................................................................................................................... 84
IRCON2 Register...................................................................................................................................... 84
TCON Register ........................................................................................................................................ 85
Low byte of Interrupt Priority Register 0: IP0 ........................................................................................... 88
High byte of Interrupt Priority Register 0: IP0H......................................................................................... 88
Low byte of Interrupt Priority Register 1: IP1 ........................................................................................... 89
High byte of Interrupt Priority Register 1: IP1H ........................................................................................ 89
Low byte of Interrupt Priority Register 2: IP2 ........................................................................................... 89
High byte of Interrupt Priority Register 2: IP2H ........................................................................................ 90
Low byte of Interrupt Priority Register 3: IP3 ........................................................................................... 90
How byte of Interrupt Priority Register 3: IP3H ........................................................................................ 90
External Interrupt Trigger Type................................................................................................................. 91
TBCR Register.......................................................................................................................................... 93
I/O Port Function Summary...................................................................................................................... 95
I/O Register List........................................................................................................................................ 96
P0 Register............................................................................................................................................... 96
P1 Register............................................................................................................................................... 96
P3 Register............................................................................................................................................... 97
P0M0 Register.......................................................................................................................................... 97
P0M1 Register.......................................................................................................................................... 97
P1M0 Register.......................................................................................................................................... 98
P1M1 Register.......................................................................................................................................... 98
P2M0 Register.......................................................................................................................................... 98
P2M1 Register.......................................................................................................................................... 98
P3M0 Register.......................................................................................................................................... 98
P3M1 Register.......................................................................................................................................... 98
P0WAKE Register..................................................................................................................................... 99
SRCR Register....................................................................................................................................... 100
PRM Register......................................................................................................................................... 100
Timer Function Summary........................................................................................................................ 104
Timer0/Timer1 Register List.................................................................................................................... 105
TL0 Register .......................................................................................................................................... 106
TH0 Register .......................................................................................................................................... 106
TL1 Register .......................................................................................................................................... 107
TH1 Register .......................................................................................................................................... 107
TMOD Register....................................................................................................................................... 108
TCON Register ...................................................................................................................................... 109
TMPRE Register......................................................................................................................................110
13-bit Counter Data.................................................................................................................................110
Timer 2 with PCA Modules Operating Modes Summary..........................................................................114
Timer 2 with PCA Modules I/O Pins.........................................................................................................114
Timer 2 Register List................................................................................................................................117
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Rev. 1.10
9 of 147
July 31, 2015
List of Tables
CCEN Register........................................................................................................................................117
T2CON Register .....................................................................................................................................118
T2CON1 Register ...................................................................................................................................118
A/D Converter Register List.................................................................................................................... 126
A/D Data Registers................................................................................................................................. 126
ADCR0 Register .................................................................................................................................... 127
ADCR1 Register..................................................................................................................................... 128
ADCR2 Register..................................................................................................................................... 129
ADPGA Register..................................................................................................................................... 130
A/D Clock Period Examples ................................................................................................................... 131
A/D Converter Voltage Reference Select............................................................................................... 132
Internal Voltage Reference Enable/Disable Control............................................................................... 136
Notes on Data Addressing Modes.......................................................................................................... 137
Notes on Program Addressing Modes.................................................................................................... 137
Arithmetic Operations............................................................................................................................. 138
Logic Operations..................................................................................................................................... 139
Data transfer Operations........................................................................................................................ 140
Program Branches.................................................................................................................................. 141
Boolean Manipulation............................................................................................................................. 142
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
List of Figures
Rev. 1.10
10 of 147
July 31, 2015
List of Figures
Stack Block Diagram................................................................................................................................ 25
Program Memory Structure...................................................................................................................... 27
Unlock Procedure Flowchart..................................................................................................................... 33
Page Erase Flowchart.............................................................................................................................. 34
Byte Read Flowchart................................................................................................................................ 35
Byte Write Flowchart (FMCR.0=1, FMCR.6=0)........................................................................................ 36
Byte Write Flowchart (FMCR.0=1, FMCR.6=1)........................................................................................ 37
Internal Data Memory Structure................................................................................................................ 42
HT85F2240/HT85F2230 XDATA............................................................................................................... 43
DPTRn Registers Control Block Diagram................................................................................................. 47
Crystal/Resonator Oscillator – HXT.......................................................................................................... 52
System Clock Configurations.................................................................................................................... 54
Watchdog Timer........................................................................................................................................ 60
Watchdog Timer Refresh Operation......................................................................................................... 65
Power-On Reset Timing ........................................................................................................................... 69
Interrupt Structure..................................................................................................................................... 85
Quasi-bidirectional I/O Structure............................................................................................................. 100
Push-pull Output Structure..................................................................................................................... 101
Open-drain Output Structure.................................................................................................................. 101
Input Only Structure................................................................................................................................ 101
Mode 0 and Mode 1 Block Diagram – Timer 0, 1....................................................................................110
Mode 2 Block Diagram – Timer 0, 1........................................................................................................111
Mode 3 Block Diagram – Timer 0............................................................................................................112
Timer 2 with PCA Modules Block Diagram..............................................................................................114
Capture Modes Block Diagram................................................................................................................118
Compare Mode 0 – Module 0~1..............................................................................................................119
Compare Match Mode 0 Timing Diagram – T2CM=0............................................................................. 120
Compare Mode 1 – Module0~1.............................................................................................................. 120
Compare Match Mode 1 Timing Diagram – T2CM=1............................................................................. 121
Reload Mode – Module 0........................................................................................................................ 122
Timer2 Clock Output Block Diagram....................................................................................................... 123
Programmable Clock Output Timing Diagram – Module 0..................................................................... 123
A/D Converter Structure......................................................................................................................... 124
Temperature vs Voltage Diagram........................................................................................................... 131
A/D Conversion Timing........................................................................................................................... 133
Ideal A/D Transfer Function (PGA Gain=1)............................................................................................. 134
Voltage Reference Generator Block Diagram......................................................................................... 135
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
1
Features
CPU Features
Features
■■ Operating Voltage:
●● fSYS=8MHz: 2.2V~5.5V
●● fSYS=12MHz: 2.7V~5.5V
●● fSYS=16MHz: 3.3V~5.5V
●● fSYS=24MHz: 4.5V~5.5V
■■ High performance 1-T architecture 8051 core
■■ Up to 24MIPS with 24MHz system clock at VDD=5V
■■ Flexible Power-down and wake-up functions to reduce power consumption
■■ Oscillator types:
●● External high frequency crystal – HXT
●● Internal high frequency RC – HIRC
●● Internal low frequency RC – LIRC
■■ Multi-mode operation: Normal, Idle and Power-Down Modes
■■ Fully integrated internal 12/16/20MHz oscillator requires no external components
■■ 8051 compatible instruction set
■■ Dual 16-bit data pointers with addition arithmetic operation
Rev. 1.10
11 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Peripheral Features
■■ Program Memory Capacity: 2K×8 ~ 4K×8
■■ Data Memory Capacity: 352×8
■■ Watchdog Timer function
■■ Up to 21 bidirectional I/O lines
Features
■■ Two pin-shared external interrupts
■■ Three 16-bit programmable Timer/Counters
■■ 16-bit Programmable Counter Array with 2 Capture/Compare Modules
■■ Multi-channel 12-bit resolution A/D converter
■■ Single Time-Base function for generation of fixed time interrupt signal
■■ Internal Temperature Sensor
■■ Low voltage reset function
■■ Low voltage detect function
■■ Wide range of available package types
Rev. 1.10
12 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
2
General Description
The device’s main features include a multi-channel 12-bit A/D Converter and multiple timers which
provide timing, capture, event counting and programmable clock output functions. Protective
features such as an internal Watchdog Timer, Low Voltage Reset and Low Voltage Detector and
excellent noise immunity and ESD protection ensure that reliable operation is maintained in hostile
electrical environments.
A full choice of external and internal low and high speed oscillator functions are provided with
the internal oscillators requiring no external components for their implementation. The ability to
operate and switch dynamically between a range of operating modes using different clock sources
gives users the ability to optimise microcontroller operation and minimise power consumption.
The inclusion of flexible I/O programming features and Time-Base function along with many
other features ensure that the devices will find excellent use in applications such as sensor signal
processing, motor driving, industrial control, consumer products and subsystem controllers in
addition to many others.
As these MCUs are Flash memory type devices, they offer offer the advantages of easy and
effective in-circuit program updates. In addition, an EV chip, in the form of the HT85V2240
device, with its OCDS (On-Chip Debug Support) interface, is supplied for full in-circuit emulation
purposes.
Rev. 1.10
13 of 147
July 31, 2015
General Description
The HT85F2230 and HT85F2240 are A/D Flash type low pin count 1-T architecture 8051 based
microcontrollers. These devices are designed for general use, however in having an internal A/D
converter, they can directly interface to analog signals, such as those from sensors. Offering users
the convenience of Flash Memory multi-programming features, these devices also include a wide
range of functions and features.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
3
Selection Table
Most features are common to all devices, the main feature distinguishing them are Program
Memory capacity, I/O count and package types. The following table summarises the main features
of each device.
VDD
HT85F2230
2.2V~
5.5V
2K×8
HT85F2240
2.2V~
5.5V
4K×8
I/O
Ext.
Interrupt
A/D
Temp.
Sensor
16-bit
Timer
16-bit
PCA
Time
Base
Package
352×8
17
2
12-bit
×9
√
3
CCU×2
1
20
SOP/SSOP
352×8
21
2
12-bit
×9
√
3
CCU×2
1
20/24
SOP/SSOP
Note: CCU stands for Compare/Capture Unit.
Rev. 1.10
14 of 147
July 31, 2015
Selection Table
Program
Data
Memory Memory
Part No.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
4
Block Diagram
The following block diagram illustrates the main functional blocks.
F�ash Programming
Circ�itr� (ICP/OCDS)
F�ash
Program
Memor�
IAP
Externa� RC
Osci��ator
Low Vo�tage
Detect
RAM Data
Memor�
80�1
Based
MCU
Core
Watchdog
Timer
Reset
Circ�it
Interr�pt
Contro��er
Interna� RC
Osci��ators
1�-bit A/D
Converter
I/O
Rev. 1.10
Timer×3
PCA
Time
Base
15 of 147
PGA
Temperat�re
Sensor
July 31, 2015
Block Diagram
Low Vo�tage
Reset
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
5
Pin Assignment
1
�0
P0.0/ICPDA/TDA
P0.6
�
19
P0.1/OSC1
�
18
P0.�/OSC�
4
17
RESET/ICPCK/TCK
P0.7/[CC0]
P1.0/[CC1]
P�.0/CC0
�
16
P�.�/INT0
VDD
6
1�
VSS
7
14
P0.�
8
1�
P0.4
9
1�
10
11
P�.�/INT1/VREF
P�.4/T0/AIN1
P�.�/T1/AIN�
P�.6/T�/AIN�
P�.7/T�EX/AIN4
P�.1/CC1/AIN�
Pin Assignment
P0.�
HT85F2240/HT85F2230/HT85V2240
20 SOP-A/SSOP-A
P0.�
1
�4
P0.0/ICPDA/TDA
P0.6
�
��
P0.1/OSC1
�
��
RESET/ICPCK/TCK
P0.7/[CC0]
P0.�/OSC�
4
�1
P�.0/CC0
�
�0
P1.0/[CC1]
P1.1
VDD
6
19
P�.�/INT0
VSS
7
18
P0.�
8
17
P0.4
P�.�/INT1/VREF
P1.�/AIN0
P�.4/T0/AIN1
P�.�/T1/AIN�
P�.6/T�/AIN�
P�.7/T�EX/AIN4
9
16
P1.4/AIN7
10
1�
P1.�/AIN6
11
14
P�.1/CC1/AIN�
1�
1�
HT85F2240/HT85V2240
24 SOP-A/SSOP-A
Note: 1. If the pin-shared pin functions have multiple outputs simultaneously, its pin names at the right side of
the “/” sign can be used for higher priority.
2. Both real IC and OCDS EV IC share the same package.
3. The TDA and TCK pins are the OCDS delicated pins and only available for the HT85V2240 device
which is the OCDS EV chip for both the HT85F2240 and HT85F2230 devices.
Rev. 1.10
16 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
6
Pin Descriptions
Pin Name
P0.0/ICPDA/TDA
P0.1/OSC1
P0.2/OSC2
P0.3~P0.6
P0.7/[CC0]
P1.0/[CC1]
P1.1
P1.2/AIN0
Function
OPT
P0.0
P0M0
P0M1
P0WAKE
ICPDA
P3.0/CC0
Rev. 1.10
ST
CMOS
Description
General purpose I/O. Register selected I/O mode and wake-up.
ICP Data Input/Output
—
P0.1
P0M0
P0M1
P0WAKE
ST
OSC1
HSOCR
HXT
P0.2
P0M0
P0M1
P0WAKE
ST
OSC2
HSOCR
—
P0M0
P0.3~P0.6
P0M1
P0WAKE
ST
CMOS General purpose I/O. Register selected I/O mode and wake-up.
P0M0
P0M1
P0WAKE
ST
CMOS General purpose I/O. Register selected I/O mode and wake-up.
CC0
PRM
ST
CMOS Compare/Capture input/output for PCA module 0
P1.0
P1M0
P1M1
ST
CMOS General purpose I/O. Register selected I/O mode
CC1
PRM
ST
CMOS Compare/Capture input/output for PCA module 1
P1.1
P1M0
P1M1
ST
CMOS General purpose I/O. Register selected I/O mode
ST
CMOS General purpose I/O. Register selected I/O mode
P0.7
P1.2
P1.3
AIN6
P1.4/AIN7
O/T
TDA
AIN0
P1.3/AIN6
—
I/T
P1.4
P1M0
P1M1
ADCR2
P1M0
P1M1
ADCR2
P1M0
P1M1
Debug Data Input/Output, only for EV chip
AN
ST
AN
ST
CMOS General purpose I/O. Register selected I/O mode and wake-up.
—
HXT pin
CMOS General purpose I/O. Register selected I/O mode and wake-up.
HXT
—
HXT pin
ADC Input Channel 0
CMOS General purpose I/O. Register selected I/O mode
—
ADC Input Channel 6
CMOS General purpose I/O. Register selected I/O mode
AIN7
ADCR2
AN
P3.0
P3M0
P3M1
—
ADC Input Channel 7
ST
CMOS General purpose I/O. Register selected I/O mode.
CC0
PRM
ST
CMOS Compare/Capture input/output for PCA module 0
17 of 147
July 31, 2015
Pin Descriptions
With the exception of the power pins, all pins on these devices can be referenced by their Port
name, e.g. P0.0, P0.1 etc, which refer to the digital I/O function of the pins. However these Port
pins are also shared with other function such as the Analog to Digital Converter etc. The function
of each pin is listed in the following table, however the details behind how each pin is configured is
contained in other sections of the datasheet.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Pin Name
P3.1/CC1/AIN5
Function
OPT
I/T
P3.1
P3M0
P3M1
ST
CMOS General purpose I/O. Register selected I/O mode.
CC1
PRM
ST
CMOS Compare/Capture input/output for PCA module 1
AIN5
ADCR2
AN
P3.2
P3M0
P3M1
ST
INT0
IEN0
TCON
ST
P3.3
P3M0
P3M1
ST
INT1
IEN0
TCON
ST
—
External Interrupt 1 Input
VREF
ADCR1
AN
—
Reference Voltage for ADC
P3.4
P3M0
P3M1
ST
T0
—
ST
—
Timer 0 External Input
AIN1
ADCR2
AN
—
ADC Input Channel 1
P3.5
P3M0
P3M1
ST
T1
—
ST
—
Timer 1 External Input
AIN2
ADCR2
AN
—
ADC Input Channel 2
P3.6
P3M0
P3M1
ST
P3.2/INT0
P3.4/T0/AIN1
P3.5/T1/AIN2
P3.6/T2/AIN3
P3.7/T2EX/AIN4
—
Description
ADC Input Channel 5
CMOS General purpose I/O. Register selected I/O mode.
—
External Interrupt 0 Input
CMOS General purpose I/O. Register selected I/O mode.
CMOS General purpose I/O. Register selected I/O mode.
CMOS General purpose I/O. Register selected I/O mode.
CMOS General purpose I/O. Register selected I/O mode.
T2
—
ST
—
Timer 2 External Input
AIN3
ADCR2
AN
—
ADC Input Channel 3
P3.7
P3M0
P3M1
ST
T2EX
—
ST
—
Timer 2 capture trigger
CMOS General purpose I/O. Register selected I/O mode.
AIN4
ADCR2
AN
—
ADC Input Channel 4
RESET
—
ST
—
Reset pin
ICPCK
—
ST
—
ICP Clock Input
TCK
—
ST
—
Debug Clock Input, only for EV chip
VDD
VDD
—
PWR
—
Positive Power supply for CORE
VSS
VSS
—
PWR
—
Negative Power supply
RESET/ICPCK/
TCK
Note: I/T: Input type;
O/T: Output type
OPT: Optional by register option
PWR: Power; ST: Schmitt Trigger input
CMOS: CMOS output;
AN: Analog input pin
HXT: high frequency crystal oscillator
Where devices exist in more than one package type the table reflects the situation for the package with the
largest number of pins. For this reason not all pins described in the table may exist on all package types.
Rev. 1.10
18 of 147
July 31, 2015
Pin Descriptions
P3.3/INT1/VREF
O/T
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
7
Absolute Maximum Ratings
Note: These are stress ratings only. Stresses exceeding the range specified under “Absolute
Maximum Ratings” may cause substantial damage to the device. Functional operation of
this device at other conditions beyond those listed in the specification is not implied and
prolonged exposure to extreme conditions may affect device reliability.
8
D.C. Characteristics
Ta=25°C
Symbol
VDD1
VDD2
Parameter
Operating Voltage
(High Frequency Internal RC
OSC)
Operating Voltage
(Crystal OSC)
Test Conditions
VDD
—
—
3V
IDD1
Operating Current
(High Frequency Internal RC
OSC)
5V
Rev. 1.10
Stanby Current
(Power-Down Mode)
(HIRC off, HXT off)
fOSC=fSYS=12MHz
HFSCR[1:0]=00b
2.7
—
5.5
fOSC=fSYS=16MHz
HFSCR[1:0]=10b
3.3
—
5.5
fOSC=fSYS=20MHz
HFSCR[1:0]=11b
4.5
—
5.5
fOSC=fSYS=8MHz
2.2
—
5.5
fOSC=fSYS=12MHz
2.7
—
5.5
fOSC=fSYS=16MHz
3.3
—
5.5
fOSC=fSYS=24MHz
4.5
—
5.5
No load, fOSC=fSYS=12MHz,
ADC off, WDT enable
—
8
12
—
16
25
Unit
V
V
mA
—
20
30
mA
5V
No load, fOSC=fSYS=20MHz,
ADC off, WDT enable
—
28
40
mA
No load, fOSC=fSYS=8MHz,
ADC off, WDT enable
—
6.0
8.5
—
12.5
20
No load, fOSC=fSYS=12MHz,
ADC off, WDT enable
—
8
12
—
16
25
3V
ISTB1
Max.
No load, fOSC=fSYS=16MHz,
ADC off, WDT enable
5V
IDD2
Typ.
5V
3V
Operating Current
(Crystal OSC)
Min.
Conditions
5V
mA
mA
5V
No load, fOSC=fSYS=16MHz,
ADC off, WDT enable
—
20
30
mA
5V
No load, fOSC=fSYS=24MHz,
ADC off, WDT enable
—
28
40
mA
—
—
1.5
—
—
2.5
3V
5V
No load, All peripherals off
19 of 147
μA
July 31, 2015
Absolute Maximum Ratings
Supply Voltage ................................................................................................. VSS-0.3V to V DD+6.0V
Input Voltage .................................................................................................... VSS-0.3V to V DD+0.3V
Storage Temperature ....................................................................................................-50°C to 125°C
Operating Temperature ................................................................................................. -40°C to 85°C
IOL Total .......................................................................................................................................150mA
IOH Total.................................................................................................................................... -100mA
Total Power Dissipation ............................................................................................................500mW
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
—
1.5
2.5
5V
No load, fOSC=4MHz (Crystal OSC)
fSYS off, ADC off, LVD/LVR disable,
WDT enable
—
3.5
5.0
VDD
3V
Conditions
Unit
ISTB2
Stanby Current (Idle)
(HIRC off, HXT on)
VIL1
Input Low Voltage
(except RESET pin)
—
quasi-bidirection mode
0
—
0.2VDD
V
VIH1
Input High Voltage
(except RESET pin)
—
quasi-bidirection mode
0.8VDD
—
VDD
V
VIL2
Input Low Voltage
(RESET pin)
—
—
0
—
0.4VDD
V
VIH2
Input High Voltage
(RESET pin)
—
—
0.9VDD
—
VDD
V
2.2V
3.0
6.0
—
IOL
I/O Port Sink Current
3.3V VOL=0.4V
4.5
9.0
—
5.0V
6.0
12.0
—
2.2V
-0.5
-1.0
—
3.3V VOH=0.9VDD
-1.0
-2.0
—
5.0V
-2.0
-4.0
—
2.2V
-20
-40
—
3.3V VOH=0.9VDD
-40
-80
—
5.0V
-80
-160
—
I/O Port Source Current
(Push-pull Mode)
mA
mA
IOH2
I/O Port Source Current
(Quasi-bidirection Mode)
IIL
Logical 0 Input Current
(Quasi-bidirection Mode)
5V
VIN=0.4V
—
—
-50
μA
ITL
Logical 1 to 0 Transition
Current (Quasi-bidirection Mode)
5V
VIN=2.4V
—
—
-950
μA
ILI
Input Leakage Current
(Input Mode)
5V
0.45V<VIN<VDD-0.3
—
—
±1
μA
VBG
Bandgap Reference with
Buffer Voltage
—
—
-3%
1.1
+3%
V
IBG
Additional Power Consumption
if Reference with Buffer is Used
—
—
—
200
300
μA
ILVR
Additional Power
Consumption if LVR is Used
3V
—
75
100
—
75
100
ILVD
Additional Power
Consumption if LVD is Used
3V
—
75
100
—
75
100
5V
5V
VLVR1
VLVR2
VLVR3
LVR enable
LVD enable
LVR Enable, 2.1V select
Low Voltage Reset Voltage
—
LVR Enable, 2.55V select
LVR Enable, 3.15V select
-5%
2.55
3.15
LVR Enable, 4.0V select
4.0
VLVD1
LVD Enable, 2.0V Select
2.0
VLVD2
LVD Enable, 2.2V Select
2.2
VLVD3
LVD Enable, 2.4V Select
2.4
VLVD5
Low Voltage Detector Voltage
—
LVD Enable, 2.7V Select
LVD Enable, 3.0V Select
-5%.
2.7
3.0
VLVD6
LVD Enable, 3.3V Select
3.3
VLVD7
LVD Enable, 3.6V Select
3.6
VLVD8
LVD Enable, 4.2V Select
4.2
Rev. 1.10
20 of 147
μA
μA
2.1
VLVR4
VLVD4
μA
+5%
V
+5%
V
July 31, 2015
D.C. Characteristics
IOH1
mA
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
9
A.C. Characteristics
Ta=25°C
Symbol
System Clock
(Crystal OSC)
Test Conditions
Min.
Typ.
2.2V~5.5V
0.4
—
8
2.7V~5.5V
0.4
—
12
0.4
—
16
0.4
—
24
VDD
Conditions
—
3.3V~5.5V
4.5V~5.5V
fSYS2
System Clock
(High Frequecny Internal RC
Oscillator)
fLIRC
32kHz Internal RC Oscillator
fHIRC
12/16/20MHz Internal RC
Oscillator
fTIMER
Timer Input Frequency
(T0~T2)
2.7V~5.5V
Ta=25°C
HFSCR[1:0]=00b
3.3V~5.5V
Ta=25°C
HFSCR[1:0]=10b
4.5V~5.5V
Ta=25°C
HFSCR[1:0]=11b
5V
Ta=25°C
Max.
Unit
MHz
12
-3%
16
+3%
MHz
20
-10%
32
+10%
-50%
32
+60%
-3%
12
+3%
2.2V~5.5V fSYS=8MHz
0
—
2
3.3V~5.5V fSYS=16MHz
0
—
4
4.5V~5.5V fSYS=24MHz
0
—
6
1
3.3
5
μs
—
1024
—
tSYS
32
64
ms
2.2V~5.5V Ta= -40°C~85°C
2.2V~5.5V
Ta=25°C
HFSCR[1:0]=00b
kHz
MHz
MHz
tRES
External Reset Minimum Low
Pulse width
—
tSST
System Start-up Timer Period
(Power-up or Wake-up from
Power-Down Mode when the
Main Oscillator is off or System
Clock is Switching between HXT
and HIRC)
—
tRSTD
System Reset Delay Time
(LVR Reset)
—
—
16
tSRESET
Software Reset Width to Reset
—
—
45
90
120
μs
tHTO
HIRC Turn On Period
—
200
—
μs
tINT
External Interrupt Minimum Pulse
Width
—
—
4
—
tSYS
tLVR
Low Voltage Width to Reset
—
120
240
480
μs
Rev. 1.10
—
fSYS =HXT or HIRC
2.2V~5.5V HIRC OFF → ON
MCU is in normal mode or
Idle mode
—
21 of 147
July 31, 2015
A.C. Characteristics
fSYS1
Parameter
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
10
ADC Electrical Characteristics
Ta=25°C
Symbol
AVDD
Parameter
A/D Converter Operating Voltage
Test Conditions
VDD
Conditions
—
—
Min.
Typ.
Max.
Unit
V
—
5.5
VREF available
0
—
VREF
—
VREF not available
0
—
AVDD
—
2
—
AVDD
V
VADI
A/D Converter Input Voltage
VREF
A/D Converter Reference Voltage
—
DNL
Differential Non-linearity
—
AVDD=5V
VREF=AVDD
tADCK=0.5μs
-2
—
+2
LSB
INL
Integral Non-linearity
—
AVDD=5V
VREF=AVDD
tADCK =0.5μs
-4
—
+4
LSB
IADC
Additional Power Consumption if
A/D Converter is used
3V
—
1.00
1.40
mA
—
1.30
2.00
mA
tADCK
A/D Converter Clock Period
—
0.5
—
10
μs
tADC
A/D Conversion Time (Include
Sample and Hold Time)
—
—
16
—
tADCK
tADS
A/D Converter Sampling Time
—
—
—
4
—
tADCK
tON2ST
ADC on to ADC start
—
—
2
—
—
μs
Rev. 1.10
5V
No load,
tADCK=0.5μs
—
12 bit ADC
22 of 147
V
July 31, 2015
ADC Electrical Characteristics
2.7
—
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
11
Comparator Electrical Characteristics
Ta=25°C
Symbol
—
Parameter
Comparator operating voltage
Test Conditions
VDD
Conditions
—
—
Min.
Typ.
Max.
Unit
—
5.5
V
—
—
10
μA
—
—
0.1
μA
—
Comparator operating current
5V
—
Comparator power-down current
5V
Comparator disable
VCMPOS
Comparator input offset voltage
5V
-10
—
+10
mV
VHP1
Positive Hysteresis 1
5V
CP0HP[1:0]=00b
—
0
1
mV
VHP2
Positive Hysteresis 2
5V
CP0HP[1:0]=01b
3
6
10
mV
VHP3
Positive Hysteresis 3
5V
CP0HP[1:0]=10b
6
13
20
mV
VHP4
Positive Hysteresis 4
5V
CP0HP[1:0]=11b
12
25
40
mV
VHN1
Negative Hysteresis 1
5V
CP0HN[1:0]=00b
—
0
1
mV
VHN2
Negative Hysteresis 2
5V
CP0HN[1:0]=01b
3
6
10
mV
VHN3
Negative Hysteresis 3
5V
CP0HN[1:0]=10b
6
13
20
mV
VHN4
Negative Hysteresis 4
5V
CP0HN[1:0]=11b
12
25
40
mV
VCM
Comparator common mode
voltage range
—
—
VSS
—
VDD1.4V
V
AOL
Comparator open loop gain
—
—
60
80
—
dB
tPD
Comparator response time
—
4
—
μs
3V
5V
—
With 100mV overdrive (Note)
Note: Measured with comparator one input pin at VCM=(VDD-1.4)/2 while the other pin input transition from VSS to
(VCM +100mV) or from VDD to (VCM -100mV).
Rev. 1.10
23 of 147
July 31, 2015
Comparator Electrical Characteristics
2.2
LVDCR=00h, ADCR1=08h, i.e.
select internal bandgap voltage
output (x2) as VREFI
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
12
Power on Reset Electrical Characteristics
Ta=25°C
Symbol
Test Conditions
Parameter
VDD
Conditions
Min.
Typ.
Max.
Unit
VDD Start Voltage to ensure Power-on Reset
—
—
—
—
100
mV
RRPOR
VDD Rising Rate to ensure Power-on Reset
—
—
0.035
—
—
V/ms
tPOR
Minimum Time for VDD stays at VPOR to ensure
Power-on Reset
—
—
1
—
—
ms
13
System Architecture
A key factor in the high-performance features of the Holtek range of microcontrollers is attributed
to their internal system architecture. The range of devices take advantage of the usual features
found within 8051-based microcontrollers providing increased speed of operation and enhanced
performance. The pipelining scheme is implemented in such a way that instruction fetching and
instruction execution are overlapped, hence most instructions are effectively executed in one clock
cycle, with the exception of branch or call instructions. Compared with classic MCU architecture,
the 8051-based core runs at a much higher speed and with greatly reduced power consumption. An
8-bit wide ALU is used in practically all operations of the 8051 compatible instruction set. It carries
out arithmetic operations, logic operations, rotation, increment, decrement, branch decisions, etc.
The internal data path is simplified by moving data through the Accumulator and the ALU. Certain
internal registers are implemented in the Data Memory and can be directly or indirectly addressed.
The simple addressing methods of these registers along with additional architectural features
ensure that a minimum of external components is required to provide a functional I/O and A/D
control system with maximum reliability and flexibility.
Rev. 1.10
24 of 147
July 31, 2015
Power on Reset Electrical Characteristics
VPOR
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
14
Program Counter
During program execution, the Program Counter is used to keep track of the address of the
next instruction to be executed. It is automatically incremented by one each time an instruction
is executed except for instructions, such as “JMP” or “CALL” that demand a jump to a nonconsecutive Program Memory address.
15
Stack
This is a special part of the memory which is used to save the contents of the Program Counter
only. The stack is located in the 256 byte Internal Data Memory; therefore, the depth can be
extended up to 256 levels. The activated level is indexed by the Stack Pointer, SP, and is neither
readable nor writeable. At a subroutine call or interrupt acknowledge signal, the contents of the
Program Counter are pushed onto the stack. At the end of a subroutine or an interrupt routine,
signaled by a return instruction, RET or RETI, the Program Counter is restored to its previous
value from the stack. After a device reset, the Stack Pointer will point to the location 0x07, the top
of the stack. Note that if the data memory has been used as the stack area, it should not be used as
general purpose Data RAM.
P ro g ra m
T o p o f S ta c k
S ta c k L e v e l 1
S ta c k L e v e l 2
S ta c k
P o in te r
B o tto m
C o u n te r
S ta c k L e v e l 3
o f S ta c k
P ro g ra m
M e m o ry
S ta c k L e v e l 2 5 6
Stack Block Diagram
If the stack is full and an enabled interrupt takes place, the interrupt request flag will be recorded
but the acknowledge signal will be inhibited. When the Stack Pointer is decremented, by RET or
RETI, the interrupt will be serviced. This feature prevents stack overflow allowing the programmer
to use the structure more easily. However, when the stack is full, a CALL subroutine instruction
can still be executed which will result in a stack overflow. Precautions should be taken to avoid
such cases which might cause unpredictable program branching.
Rev. 1.10
25 of 147
July 31, 2015
Program Counter
When executing instructions requiring jumps to non-consecutive addresses such as a jump
instruction, a subroutine call, interrupt or reset, etc., the microcontroller manages program control
by loading the required address into the Program Counter. For conditional skip instructions, once
the condition has been met, the next instruction, which has already been fetched during the present
instruction execution, is discarded and a dummy cycle takes its place while the correct instruction
is obtained.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
16
Arithmetic and Logic Unit – ALU
■■ Arithmetic operations: ADD, ADDC, SUBB, DA, MUL, DIV
■■ Logic operations: ANL, ORL, XRL, CLR, CPL
■■ Rotation: RL, RLC, RR, RRC, SWAP
■■ Increment and Decrement: INC, DEC
■■ Branch decision: JC, JNC, JB, JNB, JBC, ACALL, LCALL, RET, RETI, AJMP, SJMP, JMP, JZ,
JNZ, CJNE, DJNZ
Rev. 1.10
26 of 147
July 31, 2015
Arithmetic and Logic Unit – ALU
The arithmetic-logic unit or ALU is a critical area of the microcontroller that carries out arithmetic
and logic operations of the instruction set. Connected to the main microcontroller data bus,
the ALU receives related instruction codes and performs the required arithmetic or logical
operations after which the result will be placed in the specified register. As these ALU calculation
or operations may result in carry, borrow or other status changes, the status register will be
correspondingly updated to reflect these changes. The ALU supports the following functions:
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
17
Flash Program Memory
Structure
The Program Memory has a capacity from 2K×8 to 4K×8. The Program Memory is addressed by
the Program Counter and also contains data, table information and interrupt entries. Table data,
which can be setup in any location within the Program Memory, is addressed by a separate table
pointer register.
Special Vectors
Within the Program Memory, certain locations are reserved for the reset and interrupts. The
location 0000H is reserved for use by the device reset for program initialisation. After a device
reset is initiated, the program will jump to this location and begin execution.
HT8�F��0 HT8�F��40
000H
00�H
Reset
Reset
Interr�pt
Vector
Interr�pt
Vector
08BH
7FFH
8 bits
FFFH
8 bits
Program Memory Structure
Rev. 1.10
27 of 147
July 31, 2015
Flash Program Memory
The Program Memory is the location where the user code or program is stored. For these devices
the Program Memory is Flash type, which means it can be programmed and re-programmed
a large number of times, allowing the user the convenience of code modification on the same
device. By using the appropriate programming tools, these Flash devices offer users the flexibility
to conveniently debug and develop their applications while also offering a means of field
programming and updating.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
In-Circuit Programming – ICP
The Holtek Flash MCU to Writer Programming Pin correspondence table is as follows:
Holtek Writer Pins
MCU Programming Pins
Function
ICPDA
P0.0/ICPDA
ICPCK
RESET/ICPCK
Programming Serial Data/Address
VDD
VDD
Power Supply
VSS
VSS
Ground
Programming Serial Clock
The Program Memory can be programmed serially in-circuit using the interface on pins ICPDA
and ICPCK. Data is downloaded and uploaded serially on a single pin with an additional line for the
clock. Two additional lines are required for the power supply. The technical details regarding the
in-circuit programming of the device are beyond the scope of this document and will be supplied in
supplementary literature. The Flash Program Memory Read/Write function is implemented using a
series of registers.
On-Chip Debug Support – OCDS
An EV chip, HT85V2240, is provided which includes all the HT85F2240 functions as well as
an “On-Chip Debug” interface for emulation of the HT85F2240/2230 devices. To minimise
the difference between the real IC (the volume-production version) and the EV chip (the device
with the debug interface), a protocol converter is implemented to translate the external 2-wire
connections (TCK and TDA) into 4 internal JTAG signals (TCK, TMS, TDI and TDO) and vice
versa. Users can use the EV chip device to emulate the real chip device behavior by connecting
the TDA and TCK pins to the related Holtek development tools. The TDA pin is the OCDS Data/
Address input/output pin while the TCK pin is the OCDS clock input pin. When users use the EV
chip for debugging, other functions which are shared with the TDA and TCK pins in the actual
MCU device will have no effect in the EV chip. However, the two OCDS pins which are pin-shared
with the ICP programming pins are still used as the Flash Memory programming pins for ICP. For
a more detailed OCDS description, refer to the corresponding user’s guide.
Rev. 1.10
28 of 147
July 31, 2015
Flash Program Memory
The provision of Flash type Program Memory provides the user with a means of convenient
and easy upgrades and modifications to their programs on the same device. As an additional
convenience, Holtek has provided a means of programming the microcontroller in-circuit using
a four-line serial interface. This provides manufacturers with the possibility of manufacturing
their circuit boards complete with a programmed or un-programmed microcontroller, and then
programming or upgrading the program at a later stage. This enables product manufacturers to
easily keep their manufactured products supplied with the latest program releases without removal
and re-insertion of the device.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
In-Application Programming – IAP
An In-Application Programming interface is provided to allow the end user’s application to erase
and reprogram the user code memory. No extra code memory block (bootloader) is required to
update the firmware or non-volatile data. Firmware for the IAP and the code memory to be updated
are physically on the same IP. Users could update firmware or non-volatile data except for the sector
where IAP is located and run. A firmware library is used to provide APIs for flash programming.
With regard to the Flash Program Memory registers, there are three address registers, one 8-bit
data register and three control registers, located in the Special Function Registers. Read and Write
operations to the Flash memory are carried out in 8-bit data operations using the address and data
registers and the control registers. The address registers are named FMAR0, FMAR1 and FMAR2,
the data register is named FMDR, and the three control registers are named FMKEY, FMCR
and FMSR. As these registers are located in Special Function Register area, they can be directly
accessed in the same way as any other Special Function Register.
Program Memory Register List
Bit
Register
Name
7
6
5
4
3
2
1
0
FMAR0
FADDR7
FADDR6
FADDR5
FADDR4
FADDR3
FADDR2
FADDR1
FADDR0
FMAR1
FADDR15
FADDR14
FADDR13
FADDR12
FADDR11
FADDR10
FADDR9
FADDR8
FMAR2
INBLK
FADDR22
FADDR21
FADDR20
FADDR19
FADDR18
FADDR17
FADDR16
FMDR
FDAT7
FDAT6
FDAT5
FDAT4
FDAT3
FDAT2
FDAT1
FDAT0
FMKEY
FMKEY7
FMKEY6
FMKEY5
FMKEY4
FMKEY3
FMKEY2
FMKEY1
FMKEY0
FMCR
FMCR.7
FMCR.6
—
—
—
FMCR.2
FMCR.1
FMCR.0
FMSR
UNLOCK
—
—
—
FMPF
FMSEF
FMBF
FMBUSY
FMAR0 Register – Flash Program Memory Address Register 0
SFR Address: FAh
Bit
7
6
5
4
3
2
1
0
Name
FADDR7
FADDR6
FADDR5
FADDR4
FADDR3
FADDR2
FADDR1
FADDR0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
Rev. 1.10
Flash Program Memory address
Flash Program Memory address bit 7~bit 0
29 of 147
July 31, 2015
Flash Program Memory
Flash Program Memory Resisters
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
FMAR1 Register – Flash Program Memory Address Register 1
SFR Address: FBh
Bit
7
6
5
4
3
2
1
0
Name
FADDR15
FADDR14
FADDR13
FADDR12
FADDR11
FADDR10
FADDR9
FADDR8
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
FMAR2 Register – Flash Program Memory Address Register 2
SFR Address: FCh
Bit
7
6
5
4
3
2
1
0
Name
INBLK
FADDR22
FADDR21
FADDR20
FADDR19
FADDR18
FADDR17
FADDR16
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
INBLK: Flash memory access block selection
0: Main Flash program memory area
1: Information block area
Bit 6~0
Flash Program Memory address
Flash Program Memory address bit 22~bit 16
When writing to the Flash Memory Address Registers, they must be written in the order of
FMAR2 register first and FMAR0 register last.
Bit 7
FMDR Register – Flash Program Memory Data Register
SFR Address: FDh
Bit
7
6
5
4
3
2
1
0
Name
FDAT7
FDAT6
FDAT5
FDAT4
FDAT3
FDAT2
FDAT1
FDAT0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
Rev. 1.10
Flash Program Memory Data register
Flash Program Memory Data bit 7~bit 0
30 of 147
July 31, 2015
Flash Program Memory
Flash Program Memory address
Flash Program Memory address bit 15~bit 8
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
FMCR Register – Flash Program Memory Control Register
SFR Address: F8h
Bit
7
6
5
4
3
2
1
0
Name
FMCR.7
FMCR.6
—
—
—
FMCR.2
FMCR.1
FMCR.0
R/W
R/W
R/W
—
—
—
R/W
R/W
R/W
POR
0
1
—
—
—
0
0
0
Bit 7
Bit 5~3
Bit 2
Bit 1
Bit 0
Note that the valid combinations for FMCR.2~FMCR.0 are 100, 010 and 001, all other combinations
should be ignored.
Rev. 1.10
31 of 147
July 31, 2015
Flash Program Memory
Bit 6
FMCR.7: Flash Memory Read/Write/Erase enable control bit
0: Disable
1: Enable
As this bit is cleared automatically by hardware soon after a command is initiated, when
the MCU reads this bit it will always obtain a zero value.
FMCR.6: Flash Memory Byte Write/Page Erase control bit
0: For an un-written byte with a value of 0xFF within a page, a write operation is
allowed. But for those written bytes with any values except for 0xFF, a re-write
operation is prohibited to avoid Flash errors. The writing time is shorter.
1: Before the main program executes a byte write operation, a page erase operation
is automatically executed. Any location within the page is then rewritable, but the
write time is longer. Note that each of the security bytes 00h~1Fh in the ID block
page 0 can only be written once, the only method to release the protected bytes is
by “ICP Whole Chip Erase”.
Unimplemented, read as “0”.
FMCR.2: Flash Memory Page Erase control bit
0: Disable
1: Enable
This bit should be cleared using the application program.
FMCR.1: Flash Memory Byte Read control bit
0: Disable
1: Enable
This bit should be cleared using the application program.
FMCR.0: Flash Memory Byte Write control bit
0: Disable
1: Enable
This bit should be cleared using the application program.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
FMKEY Register – Flash Program Memory Unlock Key Data Register
SFR Address: F9h
Bit
7
6
5
4
3
2
1
0
Name
FMKEY7
FMKEY6
FMKEY5
FMKEY4
FMKEY3
FMKEY 2
FMKEY 1
FMKEY 0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
FMSR Register – Flash Program Memory Status Register
SFR Address: E2h
Bit
7
6
5
4
3
2
1
0
Name
UNLOCK
—
—
—
FMPF
FMSEF
FMBF
FMBUSY
R/W
R
—
—
—
R
R
R
R
POR
0
—
—
—
0
0
0
0
Bit 7
Bit 6~4
Bit 3
Bit 2
Bit 1
Bit 0
Rev. 1.10
UNLOCK: Flash memory Control Registers Unlock flag
0: Indicated Flash Memory Controller is locked
1: Indicated Flash Memory Controller is unlocked
Unimplemented, read as “0”
FMPF: Flash Memory Controller Procedure flag
0: The Flash Memory Controller Procedure Flag is cleared to 0 if FMSEF=1,
or if FMBF=1 or if the IAP Procedure has ended.
1: Flash Memory Controller Procedure is corrected
FMSEF: Flash Memory Controller Security Error Flag
0: Manipulation of Flash Memory does not violate the security rules
1: Manipulation of Flash Memory violates the security rules
After a flash memory manipulation, this bit must be checked to determine if the Flash
Memory manipulation has violated the security rule or not. The security rule means
to write a FFH value to SECURITY1[N] or SECURITY2[N] to set the sector N in the
unprotected mode before a flash memory manipulation. Otherwise, the manipulation
violates the security rule and the FMSEF flag will be set.
FMBF: Flash Memory Controller Break Flag
0: Manipulation of Flash Memory does not violate the security rules or lock rules or
FMCR mode change
1: Manipulation of Flash Memory violates the security rules or lock rules or FMCR
mode change
FMBUSY: Flash Memory Controller Status indication bit
0: Not erasing or rewriting
1: Busy
32 of 147
July 31, 2015
Flash Program Memory
Flash Memory Unlock Key Data register Unlock Data bits 7~bit 0
The FMKEY register is the Flash Memory Unlock key data register. If a correct key
data sequence has been written into this register, the Flash memory will release its
locked status; otherwise, the Flash memory will remain in its locked status. The correct
sequence to be written is 55H, AAH, 00H and then FFH. It is recommended to write
the key data sequence to the FMKEY register in four consecutive instructions. When
the program memory is in an unlocked status, writing any data to the FMKEY register
will result in the program memory being locked again. If there is no need to update the
program memory, it’s strongly recommended to lock the program memory at all times.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Flash Memory Read/Write Operations
The flash memory can be read from and written to using register operations. To ensure protection
of application data certain protection measures have to be first carried out before any read and
write operations are executed on the Flash Memory.
Unlocking the Flash Memory
START
Bit UNLOCK is 0
F�ash memor� is in
�ocked state
FMKEY = 0x��;
FMKEY = 0xAA;
FMKEY = 0x00;
FMKEY = 0xFF;
For examp�e� 4 consec�tive
statements in C �ang�age
Bit UNLOCK is 1
F�ash memor� is in
�n�ocked state
END
Unlock Procedure Flowchart
Rev. 1.10
33 of 147
July 31, 2015
Flash Program Memory
Before writing data to the Flash Memory it must first be unlocked. This is implemented by writing
a correct data sequence to the Flash Memory Unlock key register, FMKEY. It is recommended
to write the data sequence to the FMKEY register in 4 consecutive instructions. The following
flowchart illustrates the unlock procedure.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Page Erase Operation
The Flash Memory must be first unlocked before implementing a page erase procedure. The
flash memory address is setup using the control registers, FMAR0, FMAR1 and FMAR2. The
Flash Memory Page Erase function is selected by the control bit, FMCR.2, in the FMCR register.
Setting the FMCR.7 bit high will start the Page Erase procedure. When the procedure has finished,
the MCU will continue to run automatically. The following flowchart illustrates the Page Erase
procedure.
Flash Program Memory
F�ash memor� contro��er m�st be
In �n�ocked state
START
FMCR Bit � = 1
Write FMAR�
Write FMAR1
Write FMAR0
FMCR Bit 7 = 1
This wi�� trigger page-erasing action
Check FMSR Bit 1 = 1
Yes
No
MCU waits for page-erasing finished.
Then MCU contin�es to r�n.
END
Page Erase Flowchart
Rev. 1.10
34 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Byte Read Operation
The Flash memory must be first unlocked before implementing a byte read procedure. The flash
memory address is setup using the control registers, FMAR0, FMAR1 and FMAR2. The Flash
Memory Page Read function is selected by the control bit, FMCR.1, in the FMCR register. When
the FMCR.7 bit is set high the Byte Read procedure will be initiated. When the procedure is ready,
the MCU will continue to run automatically. The following flowchart illustrates the Byte Read
procedure.
Flash Program Memory
F�ash memor� contro��er m�st be
In �n�ocked state
START
FMCR Bit 1 = 1
Write FMAR�
Write FMAR1
Write FMAR0
FMCR Bit 7 = 1
This wi�� trigger b�te-reading action
Check FMSR Bit 1 = 1
Yes
No
Read FMDR
No
End Reading
Yes
END
Byte Read Flowchart
Rev. 1.10
35 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Byte Write Operation
START
F�ash memor� contro��er
m�st be In �n�ocked state
FMCR Bit 0 = 1 and
FMCR Bit 6 = 0 (*)
Write FMAR�
Write FMAR1
Write FMAR0
Update the Page B�ffer
B� writing FMDR
Enter memor�
d�mp proced�re
MCU waits for memor�
d�mp finished and then
MCU contin�es to r�n.
FMARx reach the
page bo�ndar�?
Yes
No
More Data?
Yes
No
FMCR Bit 7 = 1
Yes
Check FMSR Bit 1 = 1
No
MCU waits for b�te-writing
finished and then
MCU contin�es to r�n.
Write next page
if desired
Byte Write Flowchart (FMCR.0=1, FMCR.6=0)
Rev. 1.10
36 of 147
July 31, 2015
Flash Program Memory
The Flash Memory must be first unlocked before implementing a Byte Write procedure. The first
step is to assign the target memory page and erase it. Refer to the Page Erase Operation section
for details. The Flash Memory Byte Write function is controlled by the control bits, FMCR.0 and
FMCR.6, in the FMCR register. Data is first written into the FMDR register to update the Page
Buffer. The Flash memory will check if the memory address has reached the page boundary. If the
boundary has been reached or there is no more data, then set the FMCR.0 bit to high to enable the
Byte Write function. When the FMCR.7 bit is set high the Byte Write procedure will be executed.
When the procedure is ready, the MCU will continue to run automatically. The following flowchart
illustrates the Byte Write procedure.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
START
F�ash memor� contro��er
m�st be In �n�ocked state
FMCR Bit 0 = 1 and
FMCR Bit 6 = 1 (*)
Flash Program Memory
Write FMAR�
Write FMAR1
Write FMAR0
Update the Page B�ffer
B� writing FMDR
Enter memor�
d�mp proced�re
MCU waits for memor�
d�mp finished and then
MCU contin�es to r�n.
FMARx reach the
page bo�ndar�?
Yes
No
More Data?
Yes
No
FMCR Bit 7 = 1
Yes
Check FMSR Bit 1 = 1
No
MCU waits for b�te-writing
finished and then
MCU contin�es to r�n.
Write next page
if desired
Byte Write Flowchart (FMCR.0=1, FMCR.6=1)
Rev. 1.10
37 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Program Memory Protection
Memory Protection Control Bytes
The protection of program code memory is categorised to two types: Security Type 1 and Security
Type 2.
■■ Security Type 1
Take the HT85F2240 as an example, its inhibit bytes SECURITY1[0:3] are located at the
address 0x00~0x03 of the ID block page 0. If a value, with the exception of 0FFH, has been
written to SECURITY1[N], this sector can not be programmed, erased or read when in the ICP
mode or when executing the OCDSINSTR instruction in the OCDS mode.
With regard to the IAP program, in the OCDS mode, when using the OCDSINSTR instruction
to execute the IAP program, any sector with a security mechanism can be protected from being
programmed, erased or read. If the IAP program is executed when running the main program, all
sectors with security or not, can be programmed, erased or read.
With regard to the MOVC instruction, in the OCDS mode, when using the OCDSINSTR
instruction to execute the MOVC instruction, any sector with security mechanism can not be
read. When executing the MOVC instruction in the main program, all sectors with security or
not, can be read.
The following table illustrates the protection status in the OCDS/ICP/IAP/MOVC modes when
the SECURITY1[0:3] bytes are written with a value other than 0FFH:
SECURITY1[N]
N=0~3
ICP
IAP
M
O
V
C
OCDS
(5)
Main Program
Program
Erase
Read
Protect
Sector #
Remove
Protection
X
X
N/A(1)
N
Erase All
(3)
X
X
X(4)
N
Erase All
O(3)
O
O
N
Erase All
OCDS(5)
N/A(2)
X(4)
N
Erase All
Main Program
N/A(2)
O
N
Erase All
Note: (1) “N/A” means no path to read ROM code.
(2) “N/A” means without this function
(3) “X” stands for inhibited; “O” stands for enabled.
(4) If a read operation is inhibited, reading the Flash will return a fixed Flash code of 00H.
(5) In the OCDS mode, only when executing the OCDSINSTR instruction will the sectors be
protected.
Rev. 1.10
38 of 147
July 31, 2015
Flash Program Memory
The flash program memory is partitioned into two memory blocks. One is the main memory block
and the other is the ID block. The ID block size is 32 bytes and is used to setup the protected
sectors. This memory protection function is used to protect the Program Memory from improper
Program, Erase or Read operations. The flash program memory is divided into several sectors
according to the memory size. Each sector has a capacity of 1K bytes. The memory protection
function is implemented by register control. If a value, with the exception of 0FFH, is written into
the corresponding control register, the corresponding sector program memory protection function
will be enabled. This program memory sector will then be unable to be programmed, erased or read
by corresponding instructions. In this way, the user can select which block of the flash memory is
to be protected.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
■■ Security Type 2
Take the HT85F2240 as an example, its inhibit bytes SECURITY2[0:3] are located at the
addresses 0x10~0x0B of the ID block page 0. If a value, with the exception of 0FFH, is written
to SECURITY2[N], this sector can not be programmed, erased or read when in any mode.
The following table illustrates the protection state in the OCDS/ICP/IAP/MOVC modes when
the SECURITY2[0:3] bytes are written with a value other than 0FFH:
ICP
IAP
M
O
V
C
OCDS(5)
Main Program
OCDS
(5)
Main Program
Program
Erase
Read
Protect
Sector #
Remove
Protection
X
X
N/A(1)
N
Erase All
X(3)
X
X(4)
N
Erase All
X
X
X
N
Erase All
N/A
(4)
X
N
Erase All
N/A(2)
X(4)
N
Erase All
(3)
(2)
(4)
Note: (1) “N/A” means no path to read ROM code.
(2) “N/A” means without this function.
(3) “X” stands for inhibited; “O” stands for enabled.
(4) If a read operation is inhibited, reading to the Flash will return a fixed Flash code of 00H.
(5) In the OCDS mode, only when executing the OCDSINSTR instruction will the sectors be
protected.
The following tables illustrate the corresponding address ID sectors and the inhibited bytes.
HT85F2240 Program Memory Contents
The HT85F2240 program memory is divided into 4 sectors, each with a capacity of 1k bytes.
Page
0
1
Address
Description
0x00~0x03
SECURITY1[0]~ SECURITY1[3]
0x04~0x07
Not used
0x08~0x0B
SECURITY2[0]~ SECURITY2[3]
0x0C~0x0F
Not used
0x10~0x1F
Reserved
0x20~0x2F
Reserved
0x30~0x3F
Reserved
HT85F2230 Program Memory Contents
The HT85F2230 program memory is divided into 2 sectors, each with a capacity of 1k bytes.
Page
0
1
Rev. 1.10
Address
Description
0x00~0x01
SECURITY1[0]~ SECURITY1[1]
0x02~0x07
Not used
0x08~0x09
SECURITY2[0]~ SECURITY2[1]
0x0A~0x0F
Not used
0x10~0x1F
Reserved
0x20~0x2F
Reserved
0x30~0x3F
Reserved
39 of 147
July 31, 2015
Flash Program Memory
SECURITY2[N]
N=0~3
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Security Bytes
Name
Description
SECURITY1[N]
Sector N Program/Erase Inhibited Bytes
0xFF: unprotected
Else: protected
SECURITY2[N]
Sector N Access Inhibited Bytes
0xFF: unprotected
Else: protected
These two types of flash memory inhibited bytes, SECURITY1[N] and SECURITY2[N], are used
for Program Memory protection. However, the SECURITY2[N] bytes have the higher priority. If
data has be written to the SECURITY2[N] bytes, the corresponding sectors will be protected and
can not be read from or written to, no matter what data is in the SECURITY1[N] bytes. Note that
the Flash Memory protect function will not affect the instruction fetched by the MCU core. The
accompanying table illustrates the inhibited bytes priority.
SECURITY2[N]
0FFH
0FFH
Other values
except 0FFH
SECURITY1[N]
0FFH
Privilege
Sector N is not protected
Can be erased and programmed.
Can be read via flash control registers (IAP and OCDS(note1)) or the
MOVC instructions.
Other values
except 0FFH
Sector N is inhibited from Programming/Erasing
Can not be erased and programmed via ICP or flash control registers
(OCDS(note1)).
Can be erased and programmed via flash control registers (IAP).
Can be read via flash control registers (IAP) or the MOVC instructions.
X
Sector N is inhibited from Programming/Erasing/Accessing (instruction
fetch is still allowed)
Can not be erased and programmed via ICP or flash control registers
(IAP and OCDS(note1)).
Can not be read via ICP or flash control registers (IAP and OCDS(note1))
or the MOVC instructions.
Note: 1. Here “OCDS” stands for executing the OCDSINSTR instruction when in the OCDS mode.
2. Once SECURITY1[N] or SECURITY2[N] is protected, the only method to return to “unprotected state” is by “ICP Whole Chip Erase”.
Rev. 1.10
40 of 147
July 31, 2015
Flash Program Memory
Note: N=0~3
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
18
RAM Data Memory
Structure
The Data Memory is subdivided into two blocks, Internal Data RAM (IDATA) and On-Chip
External Data RAM (XDATA), which are implemented in 8-bit wide RAM. The IDATA is
subdivided into two sections, known as the Upper section and the Lower section. The Upper section
includes two blocks, the Special Function Registers, SFR, and the 128-byte General Purpose RAM.
The Special Function Register can be accessed using direct addressing methods while the 128-byte
General Purpose RAM must be accessed using indirect addressing methods.
The upper section 128-byte RAM has an address range of 80H to FFH, and is assigned to both
the General Purpose memory and the Special Function Registers. Although the address range is
identical these two RAM sections are physically separate, they are distinguished by their different
addressing methodology. Using direct addressing instructions will point to the SFR registers while
indirect addressing instructions will point to the upper 128-byte General Purpose RAM.
The lower section 128-byte RAM is dedicated to the General Purpose RAM, and consists of an 80byte General Purpose RAM section, four 8-byte register banks and 16-bytes of Bit- Addressable
Space. The lower section can be accessed both by Indirect and Direct addressing methods. The
16-byte Bit-Addressable Space, which can be addressed by both byte format and 128-bit location
format, is located from at the address range, 20H to 2FH. The four register banks, each of which
contains eight bytes of general purpose registers, are located at the address range 00H to 1FH.
The XDATA is assigned as General Purpose Data RAM and can only be accessed using indirect
addressing. The HT85F2240 and HT85F2230 have 96-bytes of XDATA.
Note that the internal data memory is also used as a software stack. The designer must initiate the
stack pointer register, namely SP, in the application program.
The following diagram illustrates the memory structure and their various access methods.
Rev. 1.10
41 of 147
July 31, 2015
RAM Data Memory
The Data Memory is a volatile area of 8-bit wide RAM internal memory and is the location where
temporary information is stored. Divided into several sections, the first of these is an area of RAM
where special function registers are located. These registers have fixed locations and are necessary
for correct operation of the devices. Many of these registers can be read and written to directly
under program control, however, some remain protected from user manipulation. The second area
of Data Memory is reserved for general purpose use. All locations within this area are read and
write accessible under program control. The Data Memory also includes the Bit-Addressable Space
and four Register Banks.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
FFH
…
…
…
Upper 128 Bytes
General Purpose RAM
(Indirect Access)
Special Function Registers
(Direct Access)
RAM Data Memory
Upper
Section
(128 bytes)
80H
…
7FH
…
…
Lower
Section
(128 bytes)
Lower 80 Bytes
General Purpose RAM
30H
Bit-Addressable Space
20H
18H
10H
08H
00H
Both direct and
indirect access
Register Bank 3
Register Bank 2
Register Bank 1
Register Bank 0
8-bit
Internal Data Memory Structure
Rev. 1.10
42 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
FFFFH
RAM Data Memory
(RESERVED)
0060H
005FH
…
…
RAM (96 bytes)
0000H
8-bit
HT85F2240/HT85F2230 XDATA
Rev. 1.10
43 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Register Banks
There are four register banks, with addresses from 00H to 1FH, with each bank containing eight
bytes. The active bank is selected by the control bits, RS1 and RS0, in the PSW register. It should
be noted that only one bank can be enabled at any time. This total of 32 bytes are used as General
Purpose data memory, which can be accessed by either direct or indirect instructions.
Some instructions in the 8051 language allow for single bit addressing. These single bit instructions
can only be used in the bit addressable data memory area, located both in the General Purpose Data
RAM and the Special Function Register area. Note that these bit addressable registers are both byte
and bit addressable.
The 16 bytes bit addressable registers of the General Purpose Data RAM, located from 20H to
2FH, can address up to 128 individual bits. Each bit has its corresponding bit address from 00H
to 7FH. For example, bit 0 of the 20H register is mapped to the bit address 00H, bit 7 of the 20H
register is mapped to the bit address 07H and bit 7 of the 2FH register is mapped to the bit address
7FH. The accompanying table illustrates the Bit-Addressable register map description for General
Purpose Data RAM, 20H ~ 2FH. Using the bit operational instruction, such as SETB or CLR on
the bit address can implement operations on the corresponding bit of the register. For example:
SETB 00H
SETB 07H
CLR 25H
CLR 7FH
;
;
;
;
Set the bit 0
Set the bit 7
Clear the bit
Clear the bit
of the register location 20H to “1”
of the register location 20H to “1”
5 of the register location 24H to “0”
7 of the register location 2FH to “0”
General Purpose Data RAM, 20H~2FH, Bit Address Map
Rev. 1.10
Low 3-bit Address
High 5-bit
Address
0H
1H
2H
3H
4H
5H
6H
7H
78H
0x2F.0
0x2F.1
0x2F.2
0x2F.3
0x2F.4
0x2F.5
0x2F.6
0x2F.7
70H
0x2E.0
0x2E.1
0x2E.2
0x2E.3
0x2E.4
0x2E.5
0x2E.6
0x2E.7
68H
0x2D.0
0x2D.1
0x2D.2
0x2D.3
0x2D.4
0x2D.5
0x2D.6
0x2D.7
60H
0x2C.0
0x2C.1
0x2C.2
0x2C.3
0x2C.4
0x2C.5
0x2C.6
0x2C.7
58H
0x2B.0
0x2B.1
0x2B.2
0x2B.3
0x2B.4
0x2B.5
0x2B.6
0x2B.7
50H
0x2A.0
0x2A.1
0x2A.2
0x2A.3
0x2A.4
0x2A.5
0x2A.6
0x2A.7
48H
0x29.0
0x29.1
0x29.2
0x29.3
0x29.4
0x29.5
0x29.6
0x29.7
40H
0x28.0
0x28.1
0x28.2
0x28.3
0x28.4
0x28.5
0x28.6
0x28.7
38H
0x27.0
0x27.1
0x27.2
0x27.3
0x27.4
0x27.5
0x27.6
0x27.7
30H
0x26.0
0x26.1
0x26.2
0x26.3
0x26.4
0x26.5
0x26.6
0x26.7
28H
0x25.0
0x25.1
0x25.2
0x25.3
0x25.4
0x25.5
0x25.6
0x25.7
20H
0x24.0
0x24.1
0x24.2
0x24.3
0x24.4
0x24.5
0x24.6
0x24.7
18H
0x23.0
0x23.1
0x23.2
0x23.3
0x23.4
0x23.5
0x23.6
0x23.7
10H
0x22.0
0x22.1
0x22.2
0x22.3
0x22.4
0x22.5
0x22.6
0x22.7
08H
0x21.0
0x21.1
0x21.2
0x21.3
0x21.4
0x21.5
0x21.6
0x21.7
00H
0x20.0
0x20.1
0x20.2
0x20.3
0x20.4
0x20.5
0x20.6
0x20.7
44 of 147
July 31, 2015
RAM Data Memory
Bit Addressable Space
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
There are also 16 bytes of bit addressable registers located in the SFR which are both byte and bit
addressable. These bit addressable registers in the SFR are registers whose addresses end with the
low 3-bit address of “000b”, such as 80h, 88h, 90h…F8h, etc. The accompanying table illustrates
the Bit-Addressable registers in the SFR. Using special instructions, such as SETB and CLR, can
implement operations on the individual bit. For example:
SETB
CLR
ACC.3
ACC.3
; Set the bit 3 of the ACC register to “1”
; Clear the bit 3 of the ACC register to “0”
Low 3-bit Address
High 5-bit
Address
0H
1H
2H
3H
4H
5H
6H
7H
F8h
FMCR.0
FMCR.1
FMCR.2
—
—
—
FMCR.6
FMCR.7
F0h
B.0
B.1
B.2
B.3
B.4
B.5
B.6
B.7
E8h
—
—
—
—
—
—
—
—
E0h
ACC.0
ACC.1
ACC.2
ACC.3
ACC.4
ACC.5
ACC.6
ACC.7
D8h
—
—
—
—
—
—
—
—
D0h
PSW.0
PSW.1
PSW.2
PSW.3
PSW.4
PSW.5
PSW.6
PSW.7
C8h
T2CON.0
T2CON.1
T2CON.2
T2CON.3
T2CON.4
—
T2CON.6
—
C0h
—
—
IRCON.2
IRCON.3
—
—
IRCON.6
IRCON.7
B8h
IP0.0
IP0.1
IP0.2
IP0.3
—
IP0.5
IP0.6
—
B0h
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
A8h
IEN0.0
IEN0.1
IEN0.2
IEN0.3
—
IEN0.5
IEN0.6
IEN0.7
A0h
—
—
—
—
—
—
—
—
98h
—
—
—
—
—
—
—
—
90h
P1.0
P1.1
P1.2
P1.3
P1.4
—
—
—
88h
TCON.0
TCON.1
TCON.2
TCON.3
TCON.4
TCON.5
TCON.6
TCON.7
80h
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
Notes: 1. address in this table is “bit address”
2. “—” stands for unimplemented
Rev. 1.10
45 of 147
July 31, 2015
RAM Data Memory
Special Function Register Bit Addresses Map
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Special Function Registers
Special Function Register Map
Low 3-bit Address
High 5-bit
Address
0H
1H
2H
3H
4H
5H
6H
7H
F8h
FMCR
FMKEY
FMAR0
FMAR1
FMAR2
FMDR
T2CON1
RSTSRC
F0h
B
ADCR0
ADCR1
ADCR2
ADPGA
ADRL
ADRH
SRST
E8h
—
—
LVRCR
LVDCR
SCCR
—
LSOCR
HSOCR
E0h
ACC
—
FMSR
—
IP1
IP1H
IP2
IP2H
D8h
—
—
—
—
—
—
—
HFSCR
D0h
PSW
—
—
—
—
PRM
—
—
C8h
T2CON
IEN3
CRCL
CRCH
TL2
TH2
IP3
IP3H
C0h
IRCON
CCEN
CCL1
CCH1
—
—
—
—
B8h
IP0
IP0H
—
—
—
—
—
IRCON2
B0h
P3
—
TBCR
—
—
—
P3M0
P3M1
A8h
IEN0
IEN1
—
—
—
—
P2M0
P2M1
A0h
P2
—
—
—
SRCR
—
P1M0
P1M1
98h
—
—
IEN2
—
—
—
P0M0
P0M1
90h
P1
P0WAKE
DPS
DPC
—
—
WDTCR
—
88h
TCON
TMOD
TL0
TL1
TH0
TH1
—
TMPRE
80h
P0
SP
DPL
DPH
DPL1
DPH1
WDTREL
PCON
Notes: “—”: unimplemented
Most of the Special Function Registers will be described in detail under the function that they
are related to. In this section a register description is provided for those registers which are not
described elsewhere.
Rev. 1.10
46 of 147
July 31, 2015
RAM Data Memory
To ensure successful operation of the microcontroller, certain internal registers, known as Special
Function Registers or SFRs for short, are implemented in the Data Memory area. These registers
ensure correct operation of internal functions such as timers, interrupts, etc., as well as external
functions such as I/O data control. The SFRs are located at the address range 80H to FFH in the
upper section and are addressed directly. All can be addressed by byte but some are also bitaddressable. The following table shows the SFR register list. Note that some of the registers are
defined by standard 8051 protocol while others are defined by Holtek.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
ACC Register – Accumulator
B Register
The B register is used as a general purpose register for these devices. It is used during multiplying
and division instructions.
SP Register – Stack Pointer
The Stack Pointer register is 8 bits wide. It denotes the top of the Stack, which is the last used
value. The user can place the Stack anywhere in the internal scratchpad Data Memory by setting
the Stack Pointer to the desired location, although the lower bytes are normally used for working
registers. After a reset, the Stack Pointer is initialised to 07H. This causes the stack to begin at
location 08H. It is used to store the return address of the main program before executing interrupt
routines or subprograms. The SP is incremented before executing a PUSH or CALL instruction and
it is decremented after executing a POP, RET or RETI instruction.
DPL, DPH, DPL1, DPH1 Registers – Data Pointer Registers
The Data Pointer (DPTR) registers, DPL, DPH, DPL1 and DPH1, although having their locations
in normal Data Memory register space, do not actually physically exist as normal registers.
Indirect addressing instructions for Data Memory data manipulation use these Indirect Addressing
Registers and Memory Pointers, in contrast to direct memory addressing, where the actual memory
address is specified. Actions on the DPTR registers will result in no actual read or write operation
to these registers but rather to the memory location specified by their corresponding Memory
Pointer for the MOVX, MOVC or JMP instructions. The DPTR registers can be operated as two
16-bit registers or four individual 8-bit registers. There are two sets of 16-bit Data Pointer register,
DPTR1 and DPTR. The DPTR register is composed of DPL and DPH, while the DPTR1 register is
composed of DPL1 and DPH1. They are generally used to access external code or data space using
instructions such as “MOVC A,@A+DPTR” or “MOVX A,@DPTR” respectively. The selection
of DPTR or DPTR1 is controlled by the DPS0 bit. Setting the DPS0 bit high will select the DPTR1
register, otherwise the DPTR register is selected.
DPTR
DPH
DPL
0
DPTR1
DPH1
DPL1
1
DPS0
Data Memor�
DPTRn Registers Control Block Diagram
Rev. 1.10
47 of 147
July 31, 2015
RAM Data Memory
The Accumulator is central to the operation of any microcontroller and is closely related with
operations carried out by the ALU. The Accumulator is the place where all intermediate results
from the ALU are stored. Without the Accumulator it would be necessary to write the result of
each calculation or logical operation such as addition, subtraction, shift, etc., to the Data Memory
resulting in higher programming and timing overheads. Data transfer operations usually involve
the temporary storage function of the Accumulator; for example, when transferring data between
one user-defined register and another, it is necessary to do this by passing the data through the
Accumulator as no direct transfer between two registers is permitted.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Data Pointer Select Registers
The devices contain up to two data pointers, depending on configuration. Each of these registers
can be used as 16-bits address source for indirect addressing. The DPS register serves to select the
active data pointer register.
DPS Register – Data Pointer Select Register
SFR Address: 92h
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
—
DPS0
R/W
—
—
—
—
—
—
—
R/W
POR
—
—
—
—
—
—
—
0
Bit 7~1
Bit 0
Unimplemented, read as “0”
DPS0: Data Pointer Register select
0: DPTR selected
1: DPTR1 selected
This bit is used to determine if the accessing addresses are sourced from either DPTR or
DPTR1 when executing Read and Write instructions.
Data Pointer Control Register
This register is used to control whether the DPTR auto-increment/auto-decrement has a value
of either 1 or 2, and auto-switching between active DPTRs functions. The auto-switching active
DPTR function is controlled by the DPC3 bit in the DPC register. The content of this bit will be
loaded to the DPS register after a MOVX @ DPTR instruction is executed. The auto-modification
function is controlled by the DPC0 bit. When this bit is enabled, the current DPTR can be
automatically increased or decreased by 1 or 2 positions selected by the DPC1 and DPC2 bits.
There are separate DPC register controls for each DPTR, to provide flexibility during data transfer
operations. The actual DPC register is selected using the DPS register. If the DPS0 bit is set high,
then DPTR1 is selected, and the DPC register is used as the DPTR1 control register. If the DPS0 bit
is cleared to zero, the DPTR is selected, and the DPC register is used as the DPTR control register.
Rev. 1.10
48 of 147
July 31, 2015
RAM Data Memory
Bit
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
DPC Register – Data Pointer Control Register
SFR Address: 93h
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
DPC3
DPC2
DPC1
DPC0
R/W
—
—
—
—
R/W
R/W
R/W
R/W
POR
—
—
—
—
0
0
0
0
Bit 2
Bit 1
Bit 0
Rev. 1.10
Unimplemented, read as “0”
DPC3: Next Data Pointer select
The content of this bit will be loaded to the “DPS” register after each MOVX @DPTR
instruction is executed.
Note that this feature is always enabled, therefore for each of the “DPC” registers this
field has to contain a different value pointing to itself, the auto-switching does not occur
with default (reset) values.
DPC2: Auto-modification size
0: Modified size by 1
1: Modified size by 2
The current DPTR will be automatically modified by size, selected by the DPC2 bit,
after each MOVX @DPTR instruction when DPC0=1.
DPC1: The current DPTR Auto-modification direction
0: Automatically incremented
1: Automatically decremented
The current DPTR will be automatically decremented or incremented, selected by the
DPC1 bit, after each MOVX @DPTR instruction when DPC0=1.
DPC0: Auto-modification control bit
0: Disable
1: Enable
When this bit is set to high, enables auto-modification of the current DPTR after each
MOVX @DPTR instruction.
49 of 147
July 31, 2015
RAM Data Memory
Bit 7~4
Bit 3
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Program Status Word
This register contains the Parity flag (P), General purpose flag 1 (F1), overflow flag (OV), Register
bank select control bits (RS0, RS1), General purpose flag 0 (F0), Auxiliary Carry flag (AC) and
Carry flag (CY). These arithmetic/logical operation and system management flags are used to
record the status and operation of the microcontroller. Note that the Parity bit can only be modified
by hardware depending upon the ACC state.
Bit
7
6
5
4
3
2
1
0
Name
CY
AC
F0
RS1
RS0
OV
F1
P
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
POR
0
0
0
0
0
0
0
0
Bit 7
Bit 6
Bit 5
Bit 4~3
Bit 2
Bit 1
Bit 0
Rev. 1.10
CY: Carry flag
0: No carry-out
1: An operation results in a carry during arithmetic operations and accumulator for
Boolean operations.
AC: Auxiliary flag
0: No auxiliary carry
1: An operation results in a carry out of the low nibbles in addition, or no borrow
from the high nibble into the low nibble on subtraction.
F0: General Purpose Flag 0
This bit is used as a general purpose flag by the application program.
RS1~RS0: Select Data Memory Banks
00: Bank 0
01: Bank 1
10: Bank 2
11: Bank 3
Locations
(within Internal Data Area)
RS1
RS0
Selected Register Bank
0
0
Bank 0
00H – 07H
0
1
Bank 1
08H – 0FH
1
0
Bank 2
10H – 17H
1
1
Bank 3
18H – 1FH
OV: Overflow flag
0: No overflow
1: An operation results in a carry into the highest-order bit but not a carry out of the
highest-order bit or vice versa.
F1: General Purpose Flag 1
This bit is used as a general purpose flag by the application program.
P: Parity flag
0: Accumulator contains an even number of ‘1’s
1: Accumulator contains an odd number of ‘1’s
This bit is used to indicate the number of ‘1’s in the Accumulator.
50 of 147
July 31, 2015
RAM Data Memory
PSW Register – Program Status Word Register
SFR Address: D0h
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
19
Oscillators
Various oscillator options offer the user a wide range of functions according to their various
application requirements. The flexible features of the oscillator functions ensure that the best
optimisation can be achieved in terms of speed and power saving. Oscillator selections and
operation are selected using internal registers.
In addition to being the source of the main system clock, the oscillators also provide clock sources
for the Watchdog Timer and Time Base functions. One external oscillator requiring some external
components and two fully integrated internal oscillators, requiring no external components, are
provided to form a wide range of both fast and slow system oscillators. After a reset occurs the
HIRC oscillator is selected as the initial system clock but can be later switched by the application
program using the clock control register.
Type
Name
Function
External High Speed Crystal
HXT
Internal High Speed RC
HIRC High Speed System Clock
Precision High Speed System Clock
Internal Low Speed RC
LIRC
WDT and Time Base Clock
Freq.
Pins
400KHz~24MHz
OSC1/OSC2
12/16/20MHz
—
32kHz
—
System Clock Configuration
There are three oscillators, two high speed oscillators and one low speed oscillator. The high speed
oscillators are the external crystal oscillator, HXT, and the internal RC oscillator, HIRC, which are
used as the system oscillators. The low speed oscillator is the internal 32kHz RC oscillator, LIRC,
which is used as peripheral clocks for the Watchdog Timer and Time Base functions.
External High Speed Crystal Oscillator – HXT
The External High Speed Crystal Oscillator is one of the high frequency oscillator choices, which is
selected via the SCCR register. For most crystal oscillator configurations, the simple connection of
a crystal across OSC1 and OSC2 will create the necessary phase shift and feedback for oscillation.
However, for some crystals and most resonator types, to ensure oscillation and accurate frequency
generation, it is necessary to add two small value external capacitors, C1 and C2. The exact values
of C1 and C2 should be selected in consultation with the crystal or resonator manufacturer’s
specification.
For oscillator stability and to minimise the effects of noise and crosstalk, it is important to ensure
thatthe crystal and any associated resistors andcapacitors along with interconnectinglines are all
located as close to the MCU as possible.
Rev. 1.10
51 of 147
July 31, 2015
Oscillators
System Oscillator Overview
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Oscillators
Crystal/Resonator Oscillator – HXT
Crystal Recommended Capacitor Values
Crystal Oscillator C1 and C2 Values
Crystal Frequency
C1
C2
24MHz
10pF
10pF
20MHz
10pF
10pF
12MHz
10pF
10pF
8 MHz
10pF
10pF
4 MHz
20pF
20pF
400KHz
300pF
300pF
Note: C1 and C2 values are for guidance only.
Internal High Speed RC Oscillator – HIRC
The internal high speed RC oscillator is a fully integrated system oscillator requiring no external
components. The internal RC oscillator has three frequencies of either 12MHz, 16MHz or 20MHz.
Device trimming during the manufacturing process and the inclusion of internal frequency
compensation circuits are used to ensure that the influence of the power supply voltage, temperature
and process variations on the oscillation frequency are minimised. If the HIRC oscillator is used as
the system oscillator, then the OSC1 and OSC2 pins should be left unconnected.
Internal Low Speed RC Oscillator – LIRC
The internal low speed oscillator, LIRC, is a fully self-contained free running on-chip RC
oscillator, used as a clock source for the Watchdog Timer and the Time Base functions. When
the microcontroller enters the IDLE Mode, the CPU clock is switched off to stop microcontroller
activity and to conserve power, however the LIRC oscillator will continue to run and can maintain
WDT and Time Base operation if it is selected as their clock source. The LIRC oscillator has a
typical frequency of 32kHz and requires no external components, however its actual frequency
may vary with temperature and supply voltage.
Rev. 1.10
52 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
20
Operating Modes and System Clocks
Present day applications require that their microcontrollers have high performance but often still
demand that they consume as little power as possible, conflicting requirements that are especially
important in battery powered portable applications. This usually requires the microcontroller can
provide a range of clock sources which can be dynamically selected.
The fast clocks required for high performance will inherently have higher power consumption
and of course vice-versa, lower speed clocks will have lower power consumption. As Holtek has
provided these devices with a range of oscillators, the user can optimise the system clock frequency
to achieve the best performance/power ratio. In addition to the two high frequency system
oscillators, a low frequency 32KHz oscillator is also provided as clock source for the WDT and
Time Base.
The MCU system clock is sourced from the high speed external crystal HXT oscillator or the
internal HIRC oscillator. These oscillators can be used directly as the system clock.
The system clock, namely f SYS, can also be used as a clock source for the peripheral functions, such
as WDT, Time Base, Timers and ADC. Refer to the related sections for the clock source selections.
Rev. 1.10
53 of 147
July 31, 2015
Operating Modes and System Clocks
System Clocks Description
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
HXTEN bit
enab�e/disab�e
M
U
X
CPU c�ock
Interna� RC
Osci��ator
HIRC
IDL bit
- enab�e/disab�e CPU c�ock
SCKS[1:0]
fSYS
HIRCEN bit
enab�e/disab�e
fSYS/16
M
U
X
Interna� RC
Osci��ator
LIRC
fWDT
Watchdog
Timer
��k
WDTCS bit
M
U
X
PD bit
- enab�e/disab�e
se�ected osci��ators
fTB
Time Base
fSYS/4 or fSYS/1�8
TBCK[1:0]
System Clock Configurations
Rev. 1.10
54 of 147
July 31, 2015
Operating Modes and System Clocks
Externa�
Cr�sta�
Osci��ator
HXT
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
There is an additional internal 32KHz low frequency clock for the peripheral circuits. It is the
internal LIRC oscillator, which is enabled using the LIRCEN bit in the LSOCR register. There is
a low frequency oscillator status bit, LIRCRDY, to indicate the “ready or not” status of the LIRC
oscillator. This bit should be monitored by the program to indicate the “ready or not” status of the
oscillator before it is used for instruction execution. This bit will be automatically cleared to zero
by hareware when the LIRC is disabled and set high once the LIRC is stable.
System Clock Control Register – SCCR
SFR Address: ECh
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
SCKS1
SCKS0
R/W
—
—
—
—
—
—
R/W
R/W
POR
—
—
—
—
—
—
0
0
Bit 7~2
Bit 1~0
Rev. 1.10
Unimplemented, read as “0”
SCKS1, SCKS0: High Frequency System clock select
00: HIRC oscillator clock source
01: HIRC oscillator clock source
10: HXT oscillator clock source
11: PLL clock source
The HIRC will be the default system clock source after a power on reset.
When switching between different clock sources an oscillator stabilisation time delay
must be provided before continuing with program execution.
55 of 147
July 31, 2015
Operating Modes and System Clocks
The main system clock source, known as f SYS, and which is used by the CPU and the peripheral
functions, can come from one of two sources. These are the internal HIRC oscillator or the external
crystal HXT oscillator. The selection is implemented using the SCKS0 and SCKS1 bits in the
SCCR register. The HXT and HIRC oscillators also have independent enable control bits, which
are the HXTEN and HIRCEN bits in the HSOCR register. There are also two oscillator status bits,
HIRCRDY and HXTRDY, in the HSOCR register to indicate whether the oscillators are ready for
operation. After power on, these status bits should be monitored by the program to indicate the
“ready or not” status of the respective oscillator before they are used with instruction execution.
After power on, the device will automatically select the HIRC oscillator as its default system clock,
which can be changed later by the application program.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
High Speed Oscillator Control Register – HSOCR
SFR Address: EFh
Bit
7
6
5
4
3
2
1
0
Name
—
—
HXTRDY
HIRCRDY
—
—
HXTEN
HIRCEN
R/W
—
—
R
R
—
—
R/W
R/W
POR
—
—
0
1
—
—
0
1
Unimplemented, read as “0”
HXTRDY: HXT oscillator ready indication bit
0: Not ready
1: Ready
This is the external high frequency oscillator, HXT, ready indication bit which indicates
if the HXT oscillator is stable or not. This bit will be cleared to zero by hardware when
the device is powered on. After power on, if the HXT oscillator is selected, the bit will
change to a high level when the external high frequency oscillator is stable.
Bit 4
HIRCRDY: HIRC oscillator ready indication bit
0: Not ready
1: Ready
This is the internal high frequency oscillator, HIRC, ready indication bit which indicates
if the HIRC oscillator is stable or not. This bit will be cleared to zero by hardware when
the HIRC function is disabled. After power on, if the HIRC oscillator is enabled, the bit
will change to a high level when the internal high frequency oscillator is stable.
Bit 3~2
Unimplemented, read as “0”
Bit 1
HXTEN: HXT control bit
0: Disable
1: Enable
Bit 0
HIRCEN: HIRC control bit
0: Disable
1: Enable
After power on, this bit will be set high thus selecting the HIRC as the initial system
oscillator.
HIRC Frequency Select Control Register – HFSCR
SFR Address: DFh
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
HFSCR1
HFSCR0
R/W
—
—
—
—
—
—
R/W
R/W
POR
—
—
—
—
—
—
0
0
Bit 7~2
Bit 1~0
Rev. 1.10
Unimplemented, read as “0”
HFSCR1~HFSCR0: HIRC Frequency Selection bit
0x: 12MHz (default frequency)
10: 16MHz
11: 20MHz
56 of 147
July 31, 2015
Operating Modes and System Clocks
Bit 7~6
Bit 5
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Low Speed Oscillator Control Register – LSOCR
SFR Address: EEh
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
LIRCRDY
—
—
LIRCEN
—
R/W
—
—
—
R
—
—
R/W
—
POR
—
—
—
1
—
—
0
—
Bit 3~2
Bit 1
Bit 0
Unimplemented, read as “0”
LIRCRDY: LIRC oscillator ready indication flag
0: Not ready
1: Ready
This is the internal low frequency oscillator, LIRC, ready indication bit which indicates
if the LIRC oscillator is stable or not. This bit will be automatically cleared to zero by
hardware when the LIRC is disabled.
Unimplemented, read as “0”
LIRCEN: LIRC oscillator select bit
0: Enable
1: Disable
Unimplemented, read as “0”
Operation Modes
There are three different modes of operation for the microcontroller, each one with its own
special characteristics and which can be chosen according to the specific performance and
power requirements of the application. There is one mode allowing normal operation of the
microcontroller, the NORMAL Mode, in which all oscillators and function remain active. There
are also two low power modes, the IDLE mode and the Power-Down Mode. In the IDLE mode,
the microcontroller CPU will stop and instruction execution will cease, however, the high speed
oscillators will continue to run and can continue to provide a clock source for the peripheral
functions such as WDT, Time Base, Timers and ADC. The slow speed oscillator will also continue
to run and keep the WDT and Time Base functions active, if its clock source is not the system
clock. In the Power-Down mode all oscillators are stopped and therefore all functions cease
operation.
Operating Mode
CPU Clock
Peripheral Clock
NORMAL Mode
IDLE Mode
Power-Down Mode
On
Off
Off
On
On
Off
Low Frequency Internal RC
Oscillator (LIRC)
On (LIRCEN=0) / Off
On (LIRCEN=0) / Off
Off
High Frequency XTAL
Oscillator (HXT)
On (HXTEN=1) / Off
On (HXTEN=1) / Off
Off
High Frequency Internal RC
Oscillator (HIRC)
On (HIRCEN=1) / Off
On (HIRCEN=1) / Off
Off
(Note)
Note: Peripheral Clock is the clock for Timer 0, Timer 1, Timer 2, PCA and ADC.
Rev. 1.10
57 of 147
July 31, 2015
Operating Modes and System Clocks
Bit 7~5
Bit 4
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
NORMAL Mode
As the name suggests this is the main operating mode where all of the selected oscillators and
clocks are active and the microcontroller has all of its functions operational and where the system
clock is provided directly by one of the high speed oscillators, HXT or HIRC.
IDLE Mode
Power - Down Mode
The Power-Down Mode is entered when the PD bit in the PCON register is set high. When the
instruction that sets the PD bit high is executed the all oscillators will stop thus inhibiting both
CPU and peripheral functions such as the WDT and Time Base if they are enabled.
Power Control Register
Two bits, PD and IDL, in the PCON register control overall mode selection.
PCON Register – Power Control Register
SFR Address: 87h
Bit
7
6
5
4
3
2
Name
SMOD
—
—
—
—
GF0
PD
IDL
R/W
R/W
—
—
—
—
R/W
R/W
R/W
POR
0
—
—
—
1
0
0
0
0
Bit 6~4
Bit 3
Bit 2
Bit 1
SMOD: Serial Port 0 double baud rate select
Described elsewhere
Unimplemented, read as “0”
Unimplemented, read as “1”
GF0: General Purpose bit
PD: Power-Down Mode control bit
Bit 0
Setting the PD bit to high will enable the Power-Down mode function. This bit will be
cleared by hardware before entering the Power-Down mode and always read as “0”.
IDL: IDLE Mode control bit
Bit 7
Rev. 1.10
1
0: No Power-Down – selected oscillators running
1: Power-Down – all oscillators stopped
0: No Idle Mode – CPU clock running
1: Idle Mode – CPU clock stopped
Setting the IDL bit to high will enable IDLE mode function. This bit will be cleared by hardware
before entering the IDLE mode and always read as “0”. Note that if the PD bit is set high, to
enable the Power-Down Mode, then the condition of the IDL bit will be overridden.
58 of 147
July 31, 2015
Operating Modes and System Clocks
The IDLE Mode is entered when the IDL bit in the PCON register is set high. When the instruction
that sets the IDL bit high is executed the CPU operation will be inhibited, however, the high
frequency clock source will continue to run and can continue to provide a clock source for the
peripheral functions if selected. The low frequency clock source will also remain operational and
can also provide a clock source for the WDT and Time Base functions, if it is enabled and if its
clock source is not selected to come from the system clock.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Standby Current Considerations
As the main reason to stop the oscillators is to keep the current consumption of the MCU to as low a
value as possible, perhaps only in the order of several micro-amps, there are other considerations which
must also be taken into account by the circuit designer if the power consumption is to be minimised.
The high speed and low speed oscillators will continue to run when in the IDLE Mode and will
thus consume some power.
Wake-up
After the system enters the IDLE or Power-Down Mode, it can be woken up from one of various
sources listed as follows:
■■ In Idle mode:
●● An external reset
●● An external low level on any P0 I/O pin
●● An external low level on INT0 and INT1 pins
●● A system interrupt
●● A WDT overflow
A system interrupt wake up can be generated by various peripheral interrupts, such as Timer 0~2
interrupt, ADC interrupt, Time base interrupt and LVD interrupt.
■■ In Power down mode:
●● An external reset
●● An external low level on any P0 I/O pin
●● An external low level on INT0 and INT1 pins
If the system is woken up by an external reset, the device will experience a full system reset,
however, if the device is woken up by a WDT overflow, a Watchdog Timer reset will be initiated.
Pins P0 [0:7] can be setup via the P0WAKE register to permit a low level on the pin to wake-up
the system. When an I/O pin wake-up occurs, the program will resume execution at the instruction
following the point where the PD or IDL control bit is set high.
If the system is woken up by an interrupt, then two possible situations may occur. The first is
where the related interrupt is disabled or the interrupt is enabled but the stack is full, in which case
the program will resume execution at the instruction following the control bits settings. In this
situation, the interrupt which woke-up the device will not be immediately serviced, but will rather
be serviced later when the related interrupt is finally enabled or when a stack level becomes free.
The other situation is where the related interrupt is enabled and the stack is not full, in which case
the regular interrupt response takes place. If an interrupt request flag is set high before entering
the IDLE or Power-Down mode, then any interrupt requests will not generate a wake-up function
and the related interrupt will be ignored. No matter what the source of the wake-up event is, once
a wake-up event occurs, the program can check if the system clock is stable or not by examining
the oscillator status bits. It is recommended that these bits are examined before proceeding with
instruction execution after a wake up.
Rev. 1.10
59 of 147
July 31, 2015
Operating Modes and System Clocks
Special attention must be made to the I/O pins on the device. All high-impedance input pins must
be connected to either a fixed high or low level as any floating input pins could create internal
oscillations and result in increased current consumption. Care must also be taken with the loads,
which are connected to I/O pins, which are setup as outputs. These should be placed in a condition
in which minimum current is drawn or connected only to external circuits that do not draw current,
such as other CMOS inputs. And for power saving purpose, all the analog modules have to be
disabled using the application program before MCU enters the IDLE or Power-Down mode.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
21
Watchdog Timer
Watchdog Co�nter Registers
fSYS
÷16
fWDT
WDTL
÷16
WDTH
WDT
Software
Reset
LIRC
WDTCS
Refresh
Contro�
Bits
WDT
SWDT
Latch
WDTREL
Refresh
Va��e
Watchdog Timer
Rev. 1.10
60 of 147
July 31, 2015
Watchdog Timer
The Watchdog Timer, also known as the WDT, is provided to inhibit program malfunctions caused
by the program jumping to unknown locations or entering endless program loops, due to certain
uncontrollable external events such as electrical noise. Its basic structure is a 16-bit timer which
when it overflows will execute an MCU reset operation. The accompanying diagram illustrates the
basic operational block diagram.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Watchdog Registers
WDT Register Contents
Bit
Register
Name
7
6
5
4
3
2
1
0
IEN0
(EAL)
WDT
(ET2)
—
(ET1)
(EX1)
(ET0)
(EX0)
IEN1
(EXEN2)
SWDT
—
—
—
—
(ECCU1)
(ECCU0)
WDTREL
D7
D6
D5
D4
D3
D2
D1
D0
WDTCR
WE4
WE3
WE2
WE1
WE0
—
—
WDTCS
IP0
—
WDTS
(PT2)
—
(PT1)
(PX1)
(PT0)
(PX0)
Note: The bit and flag names in brackets are used to manage other functions and not related to the
WDT control.
IEN0 Register
SFR Address: A8h
Bit
7
6
5
4
3
2
1
0
Name
EAL
WDT
ET2
—
ET1
EX1
ET0
EX0
R/W
R/W
R/W
R/W
—
R/W
R/W
R/W
R/W
POR
0
0
0
—
0
0
0
0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Rev. 1.10
EAL: Master interrupt global enable
Described elsewhere
WDT: Watchdog timer refresh flag
Setting this bit to “1” is the first step in initiating a Watchdog Timer refresh action. The
WDT bit must be set directly before setting the SWDT bit in the IEN1 register. The
two instructions should be executed consecutively and not have any other instruction in
between to prevent an unintentional watchdog timer refresh. This bit will be cleared by
hardware automatically. This bit is always read as “0”.
ET2: Timer 2 interrupt enable
Described elsewhere
Unimplemented, read as “0”
ET1: Timer 1 overflow interrupt enable
Described elsewhere
EX1: External interrupt 1 enable
Described elsewhere
ET0: Timer 0 overflow interrupt enable
Described elsewhere
EX0: External interrupt 0 enable
Described elsewhere
61 of 147
July 31, 2015
Watchdog Timer
There are several registers for overall watchdog timer operation. The WDTREL register is used to
setup the reload value of the Watchdog Timer. The remaining four registers are control registers
which setup the operating and control function of the WDT function. The WDTCR register
controls the WDT enable/disable operation, software reset and clock source select functions. The
WDT and SWDT bits, located in the IEN0 and IEN1 registers respectively, are used to refresh the
WDT counter to prevent the WDT overflow and reset the device. The WDTS bit in the IP0 register
is used to indicate that a WDT software reset has been generated. For details regarding the WDT
software reset function, refer to the datasheet Reset section for details.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
IEN1 Register
SFR Address: A9h
Bit
7
6
5
4
3
2
1
0
Name
EXEN2
SWDT
—
—
—
—
ECCU1
ECCU0
R/W
R/W
R/W
—
—
—
—
R/W
R/W
POR
0
0
—
—
—
—
0
0
Bit 7
Bit 5~2
Bit 1
Bit 0
WDTREL Register
SFR Address: 86h
Bit
7
6
5
4
3
2
1
0
Name
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
Rev. 1.10
Watchdog reload value
Reload value for the highest 8 bits of the watchdog timer.
This value is loaded to the Watchdog Timer when a refresh is triggered by the
consecutive setting of bits, WDT and SWDT.
62 of 147
July 31, 2015
Watchdog Timer
Bit 6
EXEN2: Timer 2 external reload interrupt enable
Described elsewhere
SWDT: Watchdog timer start/refresh flag
This bit is used to activate and refresh the watchdog timer.
When this bit is set to “1” directly after the WDT bit is set, a watchdog timer refresh
will be enabled. This bit is immediately cleared by hardware. This bit is always read as
“0”.
Unimplemented, read as “0”
ECCU1: CCU1 interrupt enable
Described elsewhere
ECCU0: CCU0 interrupt enable
Described elsewhere
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
WDTCR Register
SFR Address: 96h
Bit
7
6
5
4
3
2
1
0
Name
WE4
WE3
WE2
WE1
WE0
—
—
WDTCS
R/W
R/W
R/W
R/W
R/W
R/W
—
—
R/W
POR
0
1
0
1
0
—
—
0
Bit 7~3
WE4 ~ WE0: WDT function software control
Bit 2~1
Bit 0
Unimplemented, read as “0”
WDTCS: Watchdog clock (f WDT) selection
0: LIRC
1: fSYS / 16
Note that the WDTCR value will default to 01010000B after any reset resource which means
that the WDT will be enabled after any reset takes place. For more details regarding the reset
operation, refer to the Reset section.
IP0 Register
SFR Address: B8h
Bit
7
6
5
4
3
2
1
0
Name
—
WDTS
PT2
—
PT1
PX1
PT0
PX0
R/W
—
R/W
R/W
—
R/W
R/W
R/W
R/W
POR
—
0
0
—
0
0
0
0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Unimplemented, read as “0”
WDTS: Watchdog timer reset indication flag
0: No Watchdog timer reset
1: Watchdog timer reset
This bit must be cleared by the application program as it will not be automatically
cleared by hardware.
PT2: Timer 2 Interrupt priority low
Described elsewhere
Unimplemented, read as “0”
PT1: Timer 1 Interrupt priority low
Described elsewhere
Bit 2
PX1: External interrupt 1 priority low
Described elsewhere
Bit 1
PT0: Timer 0 Interrupt priority low
Described elsewhere
Bit 0
PX0: External interrupt 0 priority low
Described elsewhere
Rev. 1.10
63 of 147
July 31, 2015
Watchdog Timer
10101: Disable
01010: Enable - default
Other values: Reset MCU
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Watchdog Timer Clock Source
Watchdog Timer Operation
The Watchdog Timer operates by providing a device reset when its 16-bit timer overflows. The
WDT is formed of two 8-bit registers, WDTL and WDTH, both of which are inaccessible to the
application program. The WDTH register of the Watchdog Timer is reloaded with the contents of
the WDTREL register. In the application program and during normal operation the user has to
strategically clear the Watchdog Timer before it overflows to prevent the Watchdog Timer from
executing a reset. This is done by setting the WDT and SWDT bits. If the program malfunctions
for whatever reason, jumps to an unknown location, or enters an endless loop, these clear-bit
instructions will not be executed in the correct manner as setup up by the user, in which case the
Watchdog Timer will overflow and reset the device. There are five bits, WE4~WE0, in the WDTCR
register to enable/disable the Watchdog Timer. The WE4~WE0 bits must be set to a specific value
of “10101” to disable the WDT. A value of “01010” will enable the WDT while any other value will
execute an MCU reset. Using this methodology, enhanced device protection is provided. After
power on, these bits will have a value of “01010” which is the WDT enable setup value, and the
WDT function will be enabled and began counting. The application program can disable the WDT
at the beginning of the program if it is not required.
Watchdog Timer Enable/Disable Control
WE4 ~ WE0 Bits
WDT Function
01010B
Enable
10101B
Disable
Other values
Reset MCU
The watchdog timer must be refreshed regularly to prevent the reset request signal, WDTS,
from becoming active. This requirement imposes an obligation on the programmer to issue two
consecutive instructions. The first instruction is to set the WDT bit of the IEN0 register and the
second one is to set the SWDT bit in the IEN1 register. The maximum allowed delay time between
setting the WDT and SWDT bits is one instruction cycle, which means the instructions which set
the both bits should not be separated by any other instruction. If these instructions are not executed
consecutively then the WDT refresh procedure is incomplete and an unexpected WDT reset will
take place.
After the application program has set both the WDT and SWDT bits and the WDT refreshed, the
WDT bit as well the SWDT bit will be automatically cleared by hardware. The 8 high-order bits
of the Watchdog Timer are re-loaded with the contents of the WDTREL register. The larger the
WDTREL value, the shorter the WDT time out will be. For the maximum WDT time out value, the
WDTREL register should be cleared to zero.
Rev. 1.10
64 of 147
July 31, 2015
Watchdog Timer
The Watchdog Timer clock source is provided by an internal clock which is in turn supplied
by one of two sources selected by the WDTCS bit in the WDTCR register: a 32KHz clock or
f SYS/16. The 32KHz clock is sourced from the LIRC oscillator. The Watchdog Timer source clock
is then subdivided by a ratio of 16 to give a longer timeout. The LIRC internal oscillator has an
approximate period of 32KHz at a supply voltage of 5V. However, it should be noted that this
specified internal clock period can vary with V DD, temperature and process variations. The other
Watchdog Timer clock source option is the f SYS/16 clock.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
WDT running
Program sets WDT bit
Must not insert other
instructions here
Watchdog Timer
Program sets SWDT bit
WDT loaded with WDTREL
register value
H/W auto Clear WDT bit
H/W auto Clear SWDT bit
WDT continues running
Watchdog Timer Refresh Operation
Rev. 1.10
65 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
22
Low Voltage Detector – LVD
LVD Register
The Low Voltage Detector function is controlled using a single register with the name LVDCR.
Three bits in this register, LVDS2~LVDS0, are used to select one of eight fixed voltages below
which a low voltage condition will be determined. The LVDEN bit is used to control the overall on/
off function of the low voltage detector. Setting the bit high will enable the low voltage detector.
Clearing the bit to zero will switch off the internal low voltage detector circuits. As the low voltage
detector will consume a certain amount of power, it may be desirable to switch off the circuit when
not in use, an important consideration in power sensitive battery powered applications.
LVDCR Register
SFR Address: EBh
Bit
7
6
5
4
3
2
1
0
Name
LVDEN
—
—
—
—
LVDS2
LVDS1
LVDS0
R/W
R/W
—
—
—
—
R/W
R/W
R/W
POR
0
—
—
—
—
0
0
0
Bit 7
LVDEN: LVD Function Control
Bit 6~3
Bit 2~0
Unimplemented, read as “0”
LVDS2 ~ LVDS0: Select LVD Voltage
0: Disable
1: Enable
000: 2.0V
001: 2.2V
010: 2.4V
011: 2.7V
100: 3.0V
101: 3.3V
110: 3.6V
111: 4.2V
LVD Operation
The Low Voltage Detector function operates by comparing the power supply voltage, V DD, with
a pre-specified voltage level stored in the LVDCR register. This has a range of between 2.0V and
4.2V. When the power supply voltage, V DD, falls below this pre-determined value and if the LVD
interrupt function is enabled, the LVD interrupt will take place and the interrupt request flag,
LVDF, in the IRCON2 register, will be set high. The LVDF bit will be cleared to low by hardware
automatically. The LVD interrupt can cause the device to wake-up from the IDLE Mode. If the
Low Voltage Detector wake up function is not required then the LVDF flag should be first set high
and disable the LVD interrupt function before the device enters the IDLE Mode. When the device
is powered down the low voltage detector will be disabled to reduce the power consumption.
Rev. 1.10
66 of 147
July 31, 2015
Low Voltage Detector – LVD
Each device has a Low Voltage Detector function, also known as LVD. This enables the device
to monitor the power supply voltage, V DD, and provide an interrupt should it fall below a certain
level. This function may be especially useful in battery applications where the supply voltage will
gradually reduce as the battery ages, as it allows a battery low early warning signal to be generated.
The LVD function can also generate an interrupt signal if required.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
23
Reset and Initialisation
Reset Overview
The most important reset condition is after power is first applied to the microcontroller. In this
case, internal circuitry will ensure that the microcontroller, after a short delay, will be in a well
defined state and ready to execute the first program instruction. After this power-on reset, certain
important internal registers will be set to defined states before the program instructions commence
execution. One of these registers is the Program Counter, which will be reset to zero forcing the
microcontroller to begin program execution from the lowest Program Memory address.
The devices provide several reset sources to generate the internal reset signal, providing extended
MCU protection. The different types of resets are listed in the accompanying table.
Reset Source Summary
No.
Rev. 1.10
Reset Name
1
Power-On Reset
2
Reset Pin
3
Low-Voltage Reset
4
LVRCR Register Setting
Software Reset
5
Watchdog Reset
6
WDTCR Register Setting
Software Reset
7
SRST Register Setting
Software Reset
Abbreviation
Indication Bit
Register
POR
PORF
RSTSRC
Auto generated at power on
RESET
XRSTF
RSTSRC
Hardware Reset
LVR
LVRF
RSTSRC
Low VDD voltage
—
LRF
RSTSRC
Write to LVRCR register
WDT
WDTS
IP0
—
WRF
RSTSRC
—
SRSTREQ
SRST
67 of 147
Notes
Watchdog overflow
Write to WDTCR register
Write to SRST register
July 31, 2015
Reset and Initialisation
A reset function is a fundamental part of any microcontroller ensuring that the device can be set to
some predetermined condition irrespective of outside parameters. A hardware reset will of course
be automatically implemented after the device is powered-on, however there are a number of other
hardware and software reset sources that can be implemented dynamically when the device is
running.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Reset Operations
After the initial power on reset, there are many ways in which a microcontroller reset can occur,
through events occurring both internally and externally.
Reset Source Register – RSTSRC
All of the bits in the RSTSRC register are read only and can therefore not be cleared by the
application program after one of the relevant reset occurs. After one of these reset occurs and the
relevant bit is high to indicate its occurrence, the bit can only be cleared by hardware when another
different reset type occurs.
RSTSRC Register
SFR Address: FFh
Bit
7
6
5
4
3
2
1
0
Label
—
LRF
WRF
—
—
LVRF
XRSTF
PORF
R/W
—
R
R
—
—
R
R
R
POR
—
0
0
—
—
x
0
1
Bit 7
Bit 6
Bit 5
Bit 4~3
Bit 2
Bit 1
Bit 0
Rev. 1.10
Unimplemented, read as “0”
LRF: LVRCR Register Setting Software Reset Indication Flag
0: No LVRCR Setting Software Reset
1: LVRCR Software Reset
WRF: WDTCR Register Setting Software Reset Indication Flag
0: No WDTCR Setting Software Reset
1: WDTCR Setting Software Reset
Unimplemented, read as “0”
LVRF: Low-Voltage Reset Indication Flag
0: No Low-Voltage Reset
1: Low-Voltage Reset
XRSTF: External Pin Reset Indication Flag
0: No External Reset
1: External Reset
PORF: Power-on Reset Indication Flag
0: No Power-on Reset
1: Power-on Reset
68 of 147
July 31, 2015
Reset and Initialisation
After a reset occurs the device will be reset to some initial condition. Several registers are used to
indicate which actual reset type caused the device to reset. Six of the possible reset sources will be
indicated by the reset source register, RSTSRC. The additional reset sources are indicated by the
SRSTREQ bit in the SRST register for the Software Reset and the WDTS bit in the IP0 register for
the Watchdog reset.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Power-on Reset
The most fundamental and unavoidable reset is the one that occurs after power is first applied to
the microcontroller. As well as ensuring that the Program Memory begins execution from the first
memory address, a power-on reset also ensures that certain other registers are preset to known
conditions. The entire I/O data and port mode registers will power up to ensure that all pins will be
first set to the quasi-bidirection structure.
VDD
tSST
SST Time-o�t
Chip Reset
Power-On Reset Timing
Rev. 1.10
69 of 147
July 31, 2015
Reset and Initialisation
Although the microcontroller has an internal RC reset function, if the VDD power supply rise
time is not fast enough or does not stabilise quickly at power-on, the internal reset function may be
incapable of providing proper reset operation. For this reason it is recommended that an external
RC network is connected to the RESET pin, whose additional time delay will ensure that the
RESET pin remains low for an extended period to allow the power supply to stabilise. During this
time delay, normal operation of the microcontroller will be inhibited. After the RESET line reaches
a certain voltage value, the reset delay time of tSST, which is equal to 1024 system clock pulses, is
invoked to provide an extra delay time after which the microcontroller will begin normal operation.
The abbreviation SST in the figures stands for System Start-up Timer. When the Power-on reset
takes place, the PORF bit in the RSTSRC register will be set high to indicate this reset.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
RESET Pin Reset
For most applications a resistor connected between VDD and the RESET pin and a capacitor
connected between VSS and the RESET pin will provide a suitable external reset circuit. Any
wiring connected to the RESET pin should be kept as short as possible to minimise any stray noise
interference. For applications that operate within an environment where more noise is present the
Enhanced Reset Circuit shown is recommended.
Reset and Initialisation
VDD
100kO
RESET
0.1µF
Basic Reset Circuit
VDD
100kO
0.01µF
RESET
10kO
0.1µF
Enhanced Reset Circuit
This type of reset occurs when the microcontroller is already running and the RESET pin is
forcefully pulled low by external hardware such as an external switch. In this case as in the case
of other resets, the Program Counter will reset to zero and program execution initiated from this
point. Note that, during the power-up sequence, the reset circuit should make sure that the external
reset to be released after the internal power-on reset is over plus a suitable delay time. To improve
the noise immunity, the low portion of external reset signal must be greater than that specified by
tRES in the A.C. characteristics, for the internal logic to recognise a valid reset. When a RESET pin
reset takes place, the XRSTF bit in the RSTSRC register will be set high to indicate this reset.
Rev. 1.10
70 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Low Voltage Reset – LVR
The microcontroller contains a low voltage reset circuit in order to monitor the supply voltage of
the device and provide an MCU reset should the value fall below a certain predefined level.
LVRCR Register
SFR Address: EAh
Bit
7
6
5
4
3
2
1
0
Name
LVS7
LVS6
LVS5
LVS4
LVS3
LVS2
LVS1
LVS0
R/W
R/W
R/W
R/W
R/W
R
R
R/W
R/W
POR
0
0
1
1
0
0
1
1
Bit 7 ~ 0
Rev. 1.10
LVS7 ~ LVS0: LVR Voltage Select control
01010101: 2.1V
00110011: 2.55V (default)
10011001: 3.15V
10101010: 4.0V
Any other value: Generates MCU reset – register is reset to POR value
When an actual low voltage condition occurs, as specified by the above defined LVR voltage
value, an MCU reset will be generated. The reset operation will be activated after 2~3 LIRC
clock cycles. In this situation this register contents will remain the same after such a reset occurs.
Any register value, other than the four defined values above, will also result in the generation of
an MCU reset. The reset operation will be activated after 2~3 LIRC clock cycles. However in this
situation this register contents will be reset to the POR value.
71 of 147
July 31, 2015
Reset and Initialisation
The LVR function is always enabled with a specific LVR voltage, V LVR. If the supply voltage of
the device drops to within a range of 0.9V~V LVR such as might occur when changing the battery
in battery powered applications, the LVR will automatically reset the device internally and the
LVRF bit in the RSTSRC register will also be set high. For a valid LVR signal, a low voltage, i.e.,
a voltage in the range between 0.9V~ V LVR must exist for greater than the value tLVR specified in
the A.C. characteristics. If the low voltage state does not exceed this value, the LVR will ignore the
low supply voltage and will not perform a reset function. The actual VLVR value can be selected by
the LVSn bits in the LVRCR register. If the LVS7~LVS0 bits are changed to some different values
by the environmental noise, the LVR will reset the device after 2~3 LIRC clock cycles. When this
happens, the LRF bit in the RSTSRC register will be set high. After power on the register will have
the value of 00110011B. Note that the LVR function will be automatically disabled when the device
enters the power-down mode.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Watchdog Reset
All devices contain a Watchdog Timer which is used as a protection feature. The Watchdog
Timer has to be periodically cleared by the application program and prevented from overflowing
during normal MCU operation. However should the program enter an endless loop or should
external environmental conditions such as noise causes the device to jump to unpredicted program
locations, the Watchdog Timer will overflow and generate an MCU reset. Refer to the Watchdog
Timer section for more details regarding the Watchdog Timer operation.
IP0 Register
SFR Address: B8h
Bit
7
6
5
4
3
2
1
0
Name
—
WDTS
PT2
—
PT1
PX1
PT0
PX0
R/W
—
R/W
R/W
—
R/W
R/W
R/W
R/W
POR
—
0
0
—
0
0
0
0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Unimplemented, read as “0”
WDTS: Watchdog timer reset indication flag
0: No Watchdog timer reset
1: Watchdog timer reset
This bit must be cleared by the application program as it will not be automatically
cleared by hardware.
PT2: Timer 2 Interrupt priority
Described elsewhere
Unimplemented, read as “0”
PT1: Timer 1 Interrupt priority
Described elsewhere
Bit 2
PX1: External interrupt 1 priority
Described elsewhere
Bit 1
PT0: Timer 0 Interrupt priority
Described elsewhere
Bit 0
PX0: External interrupt 0 priority
Described elsewhere
Software Resets
There are three ways to generate Software Reset, each of which are generated by writing certain
values to the SRST register, the WDTCR register or the LVRCR register.
Software Reset Summary
Software Reset Name
Operation
Register
Bit
SRST
SRSTREQ
Write two successive “1” values to this bit
WDTCR Register setting
WDTCR
WE4~WE0
Write value other than “10101” or “01010”
LVRCR Register setting
LVRCR
LVS7~LVS0
Write value other than “01010101”, “00110011”,
“011001” or “10101010”
SRST Register setting
Rev. 1.10
Operation Objects
72 of 147
July 31, 2015
Reset and Initialisation
When a Watchdog Reset occurs the WDTS bit in the IP0 register will be set to indicate the reset
source. Note that this bit must be reset by the application program.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
SRST Register Software Reset
A software reset will be generated after two consecutive instructions to write a high value to the
SRSTREQ bit in the SRST register. The same bit can be used to identify the reset source.
SRST Register
SFR Address: F7h
7
6
5
4
3
2
1
0
—
—
—
—
—
—
—
SRSTREQ
R/W
—
—
—
—
—
—
—
R/W
POR
—
—
—
—
—
—
—
0
Bit 7~1
Bit 0
Unimplemented, read as “0”
SRSTREQ: Software reset request.
Writing a ‘0’ value to this bit will have no effect.
A single ‘1’ value write to this bit will have no effect.
Two consecutive ‘1’ value writes to this bit will generate a software reset.
Reading this bit can indicate the last reset source:
0: No software reset
1: Software reset
This bit must be cleared by the application program as it will not be automatically
cleared by hardware.
WDTCR Register Software Reset
A WDTCR software reset will be generated when a value other than “10101” or “01010”, exist in
the highest five bits of the WDTCR register. The WRF bit in the RSTSRC register will be set high
when this occurs, thus indicating the generation of a WDTCR software reset.
WDTCR Register
SFR Address: 96h
Bit
7
6
5
4
3
2
1
0
Name
WE4
WE3
WE2
WE1
WE0
—
—
WDTCS
R/W
R/W
R/W
R/W
R/W
R/W
—
—
R/W
POR
0
1
0
1
0
—
—
0
Bit 7~ 3
WE4 ~ WE0: WDT function software control
10101: Disable
01010: Enable - default
Other values: Reset MCU
If the MCU reset is caused by WE[4:0] in WDTC software reset, the WRF flag of
RSTSRC register will be set.
Bit 2~1
Bit 0
Unimplemented, read as “0”
WDTCS: Watchdog clock (f WDT) selection
Described elsewhere
Rev. 1.10
73 of 147
July 31, 2015
Reset and Initialisation
Bit
Label
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
LVRCR Register Software Reset
An LVRCR software reset will be generated when a value other than “01010101”, “00110011”,
“10011001” and “10101010”, exist in the LVRCR register. The LRF bit in the RSTSRC register
will be set high when this occurs, thus indicating the generation of a LVRCR software reset. The
LVRCR register value will be rest to a value of 00110011B after any reset other than the LVR reset,
and will remain unchanged after an LVR reset.
Bit
7
6
5
4
3
2
1
0
Name
LVS7
LVS6
LVS5
LVS4
LVS3
LVS2
LVS1
LVS0
R/W
R/W
R/W
R/W
R/W
R
R
R/W
R/W
POR
0
0
1
1
0
0
1
1
Bit 7 ~ 0
LVS7 ~ LVS0: LVR Voltage Select control
01010101: 2.1V
00110011: 2.55V (default)
10011001: 3.15V
10101010: 4.0V
Any other value: Generates MCU reset – register is reset to POR value
Reset Initial Conditions
The different types of reset described affect the reset flags in different ways. The following table
indicates the way in which the various components of the microcontroller are affected after a
power-on reset occurs.
Item
Condition After Reset
Program Counter
Reset to zero
Interrupts
All interrupts will be disabled
WDT
Clear after reset, WDT begins counting
Timer/Even Counters
Timer/Even Counters will be turned off
Input/Output Ports
I/O ports will be setup as a quasi-bidirection structure
Stack Pointer
Set to 007H value
The different kinds of resets all affect the internal registers of the microcontroller in different ways.
To ensure reliable continuation of normal program execution after a reset occurs, it is important to
know what condition the microcontroller is in after a particular reset occurs. The following table
describes how each type of reset affects each of the microcontroller internal registers.
Rev. 1.10
74 of 147
July 31, 2015
Reset and Initialisation
LVRCR Register
SFR Address: EAh
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
External Reset
WDT Time-out
Reset
Software Reset
0000h
0000h
0000h
0000h
P0
1111_1111b
1111_1111b
1111_1111b
1111_1111b
SP
0000_0111b
0000_0111b
0000_0111b
0000_0111b
DPL
0000_0000b
0000_0000b
0000_0000b
0000_0000b
DPH
0000_0000b
0000_0000b
0000_0000b
0000_0000b
DPL1
0000_0000b
0000_0000b
0000_0000b
0000_0000b
DPH1
0000_0000b
0000_0000b
0000_0000b
0000_0000b
WDTREL
0000_0000b
0000_0000b
uuuu_uuuub
0000_0000b
PCON
0---_1000b
0---_1000b
0---_1000b
0---_1000b
TCON
0000_0000b
0000_0000b
0000_0000b
0000_0000b
TMOD
0000_0000b
0000_0000b
0000_0000b
0000_0000b
TL0
0000_0000b
0000_0000b
0000_0000b
0000_0000b
TL1
0000_0000b
0000_0000b
0000_0000b
0000_0000b
TH0
0000_0000b
0000_0000b
0000_0000b
0000_0000b
TH1
0000_0000b
0000_0000b
0000_0000b
0000_0000b
TMPRE
--00_0000b
--00_0000b
--00_0000b
--00_0000b
P1
- - - 1 _ 1111 b
- - - 1 _ 1111 b
- - - 1 _ 1111 b
- - - 1 _ 1111 b
P0WAKE
0000_0000b
0000_0000b
0000_0000b
0000_0000b
DPS
----_---0b
----_---0b
----_---0b
----_---0b
DPC
----_0000b
----_0000b
----_0000b
----_0000b
WDTCR
0101_0--0b
0101_0--0b
0101_0--ub
0101_0--0b
IEN2
----_--0-b
----_--0-b
----_--0-b
----_--0-b
P0M0
0000_0000b
0000_0000b
0000_0000b
0000_0000b
P0M1
0000_0000b
0000_0000b
0000_0000b
0000_0000b
SRCR
----_0000b
----_0000b
----_0000b
----_0000b
SPPRE
- - - - _ - - 11 b
- - - - _ - - 11 b
- - - - _ - - 11 b
- - - - _ - - 11 b
P1M0
---0_0000b
---0_0000b
---0_0000b
---0_0000b
P1M1
---0_0000b
---0_0000b
---0_0000b
---0_0000b
IEN0
000-_0000b
000-_0000b
000-_0000b
000-_0000b
IEN1
00--_--00b
00--_--00b
00--_--00b
00--_--00b
P3
1111_1111b
1111_1111b
1111_1111b
1111_1111b
TBCR
0 - 0 0 _ - 111 b
0 - 0 0 _ - 111 b
0 - 0 0 _ - 111 b
0 - 0 0 _ - 111 b
P3M0
0000_0000b
0000_0000b
0000_0000b
0000_0000b
P3M1
0000_0000b
0000_0000b
0000_0000b
0000_0000b
IP0
-00-_0000b
-00-_0000b
-10-_0000b
-00-_0000b
IP0H
--0-_0000b
--0-_0000b
--0-_0000b
--0-_0000b
IRCON2
----_00-0b
----_00-0b
----_00-0b
----_00-0b
IRCON
00--_00--b
00--_00--b
00--_00--b
00--_00--b
CCEN
----_0000b
----_0000b
----_0000b
----_0000b
CCL1
0000_0000b
0000_0000b
0000_0000b
0000_0000b
CCH1
0000_0000b
0000_0000b
0000_0000b
0000_0000b
T2CON
-0-0_0000b
-0-0_0000b
-0-0_0000b
-0-0_0000b
Program Counter
Rev. 1.10
75 of 147
July 31, 2015
Reset and Initialisation
Power-On Reset
Register Name
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
External Reset
WDT Time-out
Reset
Software Reset
IEN3
----_00--b
----_00--b
----_00--b
----_00--b
CRCL
0000_0000b
0000_0000b
0000_0000b
0000_0000b
CRCH
0000_0000b
0000_0000b
0000_0000b
0000_0000b
TL2
0000_0000b
0000_0000b
0000_0000b
0000_0000b
TH2
0000_0000b
0000_0000b
0000_0000b
0000_0000b
IP3
----_00--b
----_00--b
----_00--b
----_00--b
IP3H
----_00--b
----_00--b
----_00--b
----_00--b
PSW
0000_0000b
0000_0000b
0000_0000b
0000_0000b
PRM
----_---0b
----_---0b
----_---0b
----_---0b
HFSCR
----_--00b
----_--00b
----_--00b
----_--00b
ACC
0000_0000b
0000_0000b
0000_0000b
0000_0000b
FMSR
0---_0000b
0---_0000b
0---_0000b
0---_0000b
IP1
----_--00b
----_--00b
----_--00b
----_--00b
IP1H
----_--00b
----_--00b
----_--00b
----_--00b
IP2
----_--0-b
----_--0-b
----_--0-b
----_--0-b
IP2H
----_--0-b
----_--0-b
----_--0-b
----_--0-b
LVRCR
0011_0011b
0011_0011b
0011_0011b
0011_0011b
LVDCR
0---_-000b
0---_-000b
0---_-000b
0---_-000b
SCCR
----_--00b
----_--00b
----_--00b
----_--00b
LSOCR
---1_--0-b
---1_--0-b
---1_--0-b
---1_--0-b
HSOCR
--01_--01b
--01_--01b
--01_--01b
--01_--01b
B
0000_0000b
0000_0000b
0000_0000b
0000_0000b
ADCR0
0110_0000b
0110_0000b
0110_0000b
0110_0000b
ADCR1
00-0_0000b
00-0_0000b
00-0_0000b
00-0_0000b
ADCR2
0000_0000b
0000_0000b
0000_0000b
0000_0000b
ADPGA
----_-000b
----_-000b
----_-000b
----_-000b
ADRL(ADRFS=0)
0000_----b
0000_----b
0000_----b
0000_----b
ADRH(ADRFS=0)
0000_0000b
0000_0000b
0000_0000b
0000_0000b
SRST
----_---0b
----_---0b
----_---0b
----_---1b
FMCR
01--_-000b
01--_-000b
01--_-000b
01--_-000b
FMKEY
0000_0000b
0000_0000b
0000_0000b
0000_0000b
FMAR0
0000_0000b
0000_0000b
0000_0000b
0000_0000b
FMAR1
0000_0000b
0000_0000b
0000_0000b
0000_0000b
FMAR2
0000_0000b
0000_0000b
0000_0000b
0000_0000b
FMDR
0000_0000b
0000_0000b
0000_0000b
0000_0000b
T2CON1
---0_10--b
---u_10--b
---u_10--b
---u_10--b
RSTSRC
-000_-x01b
-000_-010b
-000_-000b
-000_-000b
Rev. 1.10
76 of 147
July 31, 2015
Reset and Initialisation
Power-On Reset
Register Name
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Register Name
LVR Reset
LVRCR Reset
0000h
0000h
0000h
P0
1111_1111b
1111_1111b
1111_1111b
SP
0000_0111b
0000_0111b
0000_0111b
DPL
0000_0000b
0000_0000b
0000_0000b
DPH
0000_0000b
0000_0000b
0000_0000b
DPL1
0000_0000b
0000_0000b
0000_0000b
DPH1
0000_0000b
0000_0000b
0000_0000b
WDTREL
0000_0000b
0000_0000b
0000_0000b
PCON
0---_1000b
0---_1000b
0---_1000b
TCON
0000_0000b
0000_0000b
0000_0000b
TMOD
0000_0000b
0000_0000b
0000_0000b
TL0
0000_0000b
0000_0000b
0000_0000b
TL1
0000_0000b
0000_0000b
0000_0000b
TH0
0000_0000b
0000_0000b
0000_0000b
TH1
0000_0000b
0000_0000b
0000_0000b
TMPRE
--00_0000b
--00_0000b
--00_0000b
P1
- - - 1 _ 1111 b
- - - 1 _ 1111 b
- - - 1 _ 1111 b
P0WAKE
0000_0000b
0000_0000b
0000_0000b
DPS
----_---0b
----_---0b
----_---0b
DPC
----_0000b
----_0000b
----_0000b
WDTCR
0101_0--0b
0101_0--0b
0101_0--0b
IEN2
----_--0-b
----_--0-b
----_--0-b
P0M0
0000_0000b
0000_0000b
0000_0000b
P0M1
0000_0000b
0000_0000b
0000_0000b
P2
----_---1b
----_---1b
----_---1b
SRCR
----_0000b
----_0000b
----_0000b
P1M0
---0_0000b
---0_0000b
---0_0000b
P1M1
---0_0000b
---0_0000b
---0_0000b
IEN0
000-_0000b
000-_0000b
000-_0000b
IEN1
00--_--00b
00--_--00b
00--_--00b
P3
1111_1111b
1111_1111b
1111_1111b
TBCR
0 - 0 0 _ - 111 b
0 - 0 0 _ - 111 b
0 - 0 0 _ - 111 b
P3M0
0000_0000b
0000_0000b
0000_0000b
P3M1
0000_0000b
0000_0000b
0000_0000b
IP0
-00-_0000b
-00-_0000b
-00-_0000b
IP0H
--0-_0000b
--0-_0000b
--0-_0000b
IRCON2
----_00-0b
----_00-0b
----_00-0b
IRCON
00--_00--b
00--_00--b
00--_00--b
CCEN
----_0000b
----_0000b
----_0000b
CCL1
0000_0000b
0000_0000b
0000_0000b
CCH1
0000_0000b
0000_0000b
0000_0000b
T2CON
-0-0_0000b
-0-0_0000b
-0-0_0000b
IEN3
----_00--b
----_00--b
----_00--b
Rev. 1.10
77 of 147
July 31, 2015
Reset and Initialisation
WDTCR Reset
Program Counter
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Register Name
LVR Reset
LVRCR Reset
CRCL
0000_0000b
0000_0000b
0000_0000b
CRCH
0000_0000b
0000_0000b
0000_0000b
TL2
0000_0000b
0000_0000b
0000_0000b
TH2
0000_0000b
0000_0000b
0000_0000b
IP3
----_00--b
----_00--b
----_00--b
IP3H
----_00--b
----_00--b
----_00--b
PSW
0000_0000b
0000_0000b
0000_0000b
PRM
----_---0b
----_---0b
----_---0b
HFSCR
----_--00b
----_--00b
----_--00b
ACC
0000_0000b
0000_0000b
0000_0000b
FMSR
0---_0000b
0---_0000b
0---_0000b
IP1
----_--00b
----_--00b
----_--00b
IP1H
----_--00b
----_--00b
----_--00b
IP2
----_--0-b
----_--0-b
----_--0-b
IP2H
----_--0-b
----_--0-b
----_--0-b
LVRCR
0011_0011b
uuuu_uuuub
0011_0011b
LVDCR
0---_-000b
0---_-000b
0---_-000b
SCCR
----_--00b
----_--00b
----_--00b
LSOCR
---1_--0-b
---1_--0-b
---1_--0-b
HSOCR
--01_--01b
--01_--01b
--01_--01b
B
0000_0000b
0000_0000b
0000_0000b
ADCR0
0110_0000b
0110_0000b
0110_0000b
ADCR1
00-0_0000b
00-0_0000b
00-0_0000b
ADCR2
0000_0000b
0000_0000b
0000_0000b
ADPGA
----_-000b
----_-000b
----_-000b
ADRL(ADRFS=0)
0000_----b
0000_----b
0000_----b
ADRH(ADRFS=0)
0000_0000b
0000_0000b
0000_0000b
SRST
----_---0b
----_---0b
----_---0b
FMCR
01--_-000b
01--_-000b
01--_-000b
FMKEY
0000_0000b
0000_0000b
0000_0000b
FMAR0
0000_0000b
0000_0000b
0000_0000b
FMAR1
0000_0000b
0000_0000b
0000_0000b
FMAR2
0000_0000b
0000_0000b
0000_0000b
FMDR
0000_0000b
0000_0000b
0000_0000b
T2CON1
---u_10--b
---u_10--b
---u_10--b
RSTSRC
-010_-000b
-000_ -100b
-100_-000b
Note: "-" not implement
"u" stands for "unchanged"
"x" stands for "unknown"
Rev. 1.10
78 of 147
July 31, 2015
Reset and Initialisation
WDTCR Reset
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
24
Interrupts
Interrupt Registers
Overall interrupt control, which means interrupt enabling, priority and request flag setting, is
controlled using several registers. By controlling the appropriate enable bits in these registers each
individual interrupt can be enabled or disabled. Also when an interrupt occurs, the corresponding
request flag will be automatically set by the microcontroller. The global enable control bit if cleared
to zero will disable all interrupts.
Overall interrupt control, which basically means the setting of request f lags when certain
microcontroller conditions occur and the setting of interrupt enable bits by the application program,
is controlled by a series of registers, located in the Special Function Registers, as shown in the
accompanying table. Each register contains a number of enable bits to enable or disable individual
registers as well as interrupt flags to indicate the presence of an interrupt request.
Interrupt Register Bit Naming Conventions
Function
Global
INTn Pin
A/D Converter
Enable Bit
Request Flag
Notes
EAL
—
—
EXn
IEn
n=0~1
EADC
IADC
—
Time Base
ETB
TBF
—
LVD
ELVD
LVDF
—
Timer n
ETn
TFn
n=0~2
CCUn
ECCUn
CCUnF
n=0~1
Timer 2 External Reload
EXEN2
EXF2
—
Interrupt Register Contents
Register
Name
Bit
7
6
5
4
3
2
1
0
IEN0
EAL
(WDT)
ET2
—
ET1
EX1
ET0
EX0
IEN1
EXEN2
(SWDT)
—
—
—
—
ECCU1
ECCU0
IEN2
—
—
—
—
—
—
ELVD
—
IEN3
—
—
—
—
ETB
EADC
—
—
IRCON
EXF2
TF2
—
—
CCU1F
CCU0F
—
—
IRCON2
—
—
—
—
LVDF
TBF
—
IADC
TCON
TF1
(TR1)
TF0
(TR0)
IE1
IT1
IE0
IT0
T2CON
—
I3FR
—
(T2R1)
(T2R0)
(T2CM)
(T2I1)
(T2I0)
Note: The bits in brackets are used to manage other functions and not related to the interrupt control.
Rev. 1.10
79 of 147
July 31, 2015
Interrupts
Interrupts are an important part of any microcontroller system. When an external event or an
internal function such as a Timer/Event Counter or Time Base requires microcontroller attention,
their corresponding interrupt will enforce a temporary suspension of the main program allowing
the microcontroller to direct attention to their respective needs. These devices contain multiple
external interrupt pins, while the internal interrupts are generated by the various functions such as
Timer/Event Counters, Time Base, LVD and the A/D converter. In addition, the interrupt priority
can be controlled using registers.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
IEN0 Register
SFR Address: A8h
Bit
7
6
5
4
3
2
1
0
Name
EAL
WDT
ET2
—
ET1
EX1
ET0
EX0
R/W
R/W
R/W
R/W
—
R/W
R/W
R/W
R/W
POR
0
0
0
—
0
0
0
0
Bit 7
EAL: Master interrupt global enable
Bit 6
WDT: Watchdog timer refresh flag
Interrupts
0: Disable
1: Enable
Described elsewhere
Bit 5
ET2: Timer 2 interrupt enable
0: Disable
1: Enable
Bit 4
Unimplemented, read as “0”
Bit 3
ET1: Timer 1 interrupt enable
Bit 2
EX1: External interrupt 1 enable
0: Disable
1: Enable
Bit 1
ET0: Timer 0 interrupt enable
Bit 0
EX0: External interrupt 0 enable
0: Disable
1: Enable
0: Disable
1: Enable
0: Disable
1: Enable
IEN1 Register
SFR Address: A9h
Rev. 1.10
Bit
7
6
5
4
3
2
1
0
Name
EXEN2
SWDT
—
—
—
—
ECCU1
ECCU0
R/W
R/W
R/W
—
—
—
—
R/W
R/W
POR
0
0
—
—
—
—
0
0
Bit 7
EXEN2: Timer 2 external reload interrupt enable
Bit 6
Bit 5~2
Bit 1
1: Enable
When EXEN2=0, Timer 2 external reload interrupt is disabled. When EXEN2=1,
EAL=1 and ET2=1, Timer 2 externla reload interrupt 2 is enabled.
SWDT: Watchdog timer start/refresh flag
Described elsewhere
Unimplemented, read as “0”
ECCU1: CCU1 interrupt enable
Bit 0
ECCU0: CCU0 interrupt enable
0: Disable
0: Disable
1: Enable
0: Disable
1: Enable
80 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
IEN2 Register
SFR Address: 9Ah
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
ELVD
—
R/W
—
—
—
—
—
—
R/W
—
POR
—
—
—
—
—
—
0
—
Unimplemented, read as “0”
ELVD: LVD interrupt enable
Bit 0
Unimplemented, read as “0”
Interrupts
Bit 7~2
Bit 1
0: Disable
1: Enable
IEN3 Register
SFR Address: C9h
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
ETB
EADC
—
—
R/W
—
—
—
—
R/W
R/W
—
—
POR
—
—
—
—
0
0
—
—
Bit 7~4
Bit 3
Bit 2
Bit 1~0
Rev. 1.10
Unimplemented, read as “0”
ETB: Time Base interrupt enable
0: Disable
1: Enable
EADC: ADC interrupt enable
0: Disable
1: Enable
Unimplemented, read as “0”
81 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
IRCON Register
SFR Address: C0h
Bit
7
6
5
4
3
2
1
0
Name
EXF2
TF2
—
—
CCU1F
CCU0F
—
—
R/W
R/W
R/W
—
—
R/W
R/W
—
—
POR
0
0
—
—
0
0
—
—
Bit 7
Bit 6
1: Interrupt request
The EXF2 bit will be set high by a negative transition on the T2EX pin. This bit must
be cleared using the application program. The EXF2 bit will be invalid in the Timer 2
Timer/Counter mode.
TF2: Timer 2 overflow interrupt request flag
Bit 5~4
Bit 3
This bit must be cleared using the application program.
Unimplemented, read as “0”
CCU1F: CCU1 interrupt request flag
Bit 2
This bit will be set high when Timer 2 compare mode is enabled and counter value (TH2,
TL2) is equal to Compare/Capture register 1 (CCH1, CCL1). Additionally, this bit can
be set high when Timer 2 Capture mode 0 is enabled and a rising edge is detected on
CC1 input pin. Once the program into the interrupt subroutine, the CCU1F flag will be
cleared by hardware automatically.
CCU0F: CCU0 interrupt request flag
0: No request
1: Interrupt request
0: No request
1: Interrupt request
0: No request
1: Interrupt request
This bit will be set high when Timer 2 compare mode is enabled and counter value (TH2,
TL2) is equal to Compare/Reload/Capture register 3 (CRCH, CRCL). Additionally, this
bit can be set high when Timer 2 Capture mode 0 is enabled and a rising or falling edge
(depending on the I3FR bit) is detected on CC0 input pin. Once the program into the
interrupt subroutine, the CCU0F flag will be cleared by hardware automatically.
Bit 1~0
Rev. 1.10
Unimplemented, read as “0”
82 of 147
July 31, 2015
Interrupts
EXF2: Timer 2 external reload interrupt request flag
0: No request
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
T2CON Register
SFR Address: C8h
Bit
7
6
5
4
3
2
1
0
Name
—
I3FR
—
T2R1
T2R0
T2CM
T2I1
T2I0
R/W
—
R/W
—
R/W
R/W
R/W
R/W
R/W
POR
—
0
—
0
0
0
0
0
Bit 5
Bit 4~3
Unimplemented, read as “0”
I3FR: Timer 2 capture mode 0 edge selection for “CC0”
0: Falling edge
1: Rising edge
This bit is used as capture signal in CC0. When Timer 2 is selected as compare
mode 0, for compare interrupt flag active high timing consideration, the I3FR bit is
recommended to be set high by firmware.
Unimplemented, read as “0”
T2R1, T2R0: Timer 2 reload mode selection
Described elsewhere
Bit 2
T2CM: Timer 2 Compare mode selection
Described elsewhere
Bit 1~0
T2I1, T2I0: Timer 2 input selection
Described elsewhere
IRCON2 Register
SFR Address: BFh
Rev. 1.10
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
LVDF
TBF
—
IADC
R/W
—
—
—
—
R/W
R/W
—
R/W
POR
—
—
—
—
0
0
—
0
Bit 7 ~ 4
Bit 3
Unimplemented, read as “0”
LVDF: LVD interrupt request flag
Bit 2
This bit will be cleared by hardware automatically.
TBF: Time Base interrupt request flag
Bit 1
Bit 0
This bit will be cleared by hardware automatically.
Unimplemented, read as “0”
IADC: ADC interrupt request flag
0: No request
1: Interrupt request
0: No request
1: Interrupt request
0: No request
1: Interrupt request
This bit will be cleared by hardware automatically.
83 of 147
July 31, 2015
Interrupts
Bit 7
Bit 6
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
TCON Register
SFR Address: 88h
Bit
7
6
5
4
3
2
1
0
Name
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7
Bit 5
This bit will be cleared by hardware automatically when the interrupt is processed.
TR1: Timer 1 Run control
Described elsewhere
TF0: Timer 0 interrupt request flag
0: No request
1: Interrupt request
Bit 3
This bit will be cleared by hardware automatically when the interrupt is processed.
TR0: Timer 0 Run control
Described elsewhere
IE1: External interrupt 1 request flag
Bit 2
This bit is set by hardware when the external interrupt INT1 (edge, depending on
settings) is observed. This bit will be cleared by hardware when the interrupt is
processed.
When the external interrupt INT1 (level, depending on settings) is observed, IE1 is the
inverse level of the INT1.
IT1: External interrupt 1 type control
Bit 1
IE0: External interrupt 0 request flag
Bit 0
This bit is set by hardware when the external interrupt INT0 (edge, depending on
settings) is observed. This bit will be cleared by hardware when the interrupt is
processed.
When the external interrupt INT0 (level, depending on settings) is observed, IE0 is the
inverse level of the INT0.
IT0: External interrupt 0 type control
Bit 4
Rev. 1.10
0: No request
1: Interrupt request
0: No request
1: Interrupt request
0: Low Level
1: Falling Edge
0: No request
1: Interrupt request
0: Low Level
1: Falling Edge
84 of 147
July 31, 2015
Interrupts
Bit 6
TF1: Timer 1 interrupt request flag
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Interrupt Operation
The EAL is used to control the whole interrupt function enable or disable and it has to be cleared
using the application program.
The various interrupt enable bits, together with their associated request flags, are shown in the
following diagram with their order of priority. Interrupts with higher priority can stop lower
priority ones. All interrupts are categorised into four priority levels.
Legend
xxx Request Flag – no auto reset in ISR
xxx Request Flag – auto reset in ISR
Exx Enable Bit
Interrupt
Name
Request
Flags
Enable
Bits
Master
Enable
INT0 Pin
IE0
EX0
EAL
03H
Timer 0
TF0
ET0
EAL
0BH
INT1 Pin
IE1
EX1
EAL
13H
Timer 1
TF1
ET1
EAL
1BH
Vector
Timer 2
TF2/EXF2
ET2/EXEN2
EAL
2BH
CCU0
CCU0F
ECCU0
EAL
43H
CCU1
CCU1F
ECCU1
EAL
4BH
ADC
IADC
EADC
EAL
73H
Time Base
TBF
ETB
EAL
7BH
LVD
LVDF
ELVD
EAL
8BH
Priority
High
Low
Interrupt Structure
Note that if one interrupt requests occur during the other interrupt interval, although the interrupt
will not be immediately serviced, the request flag will still be recorded and the next interrupt
request will take place according to the interrupt priority. If the stack is full, the interrupt request
will not be acknowledged, even if the related interrupt is enabled, until the Stack Pointer is
decremented. If immediate service is desired, the stack must be prevented from becoming full.
When an interrupt request is generated, it takes several instruction cycles before the program jumps
to the interrupt vector.
Rev. 1.10
85 of 147
July 31, 2015
Interrupts
A Timer Counter overflow, an active edge or level on the external interrupt pin, a comparator
output changes state or A/D conversion completion etc, will all generate an interrupt request by
setting their corresponding request flag. When this happens, if the interrupt enable bit is set, then
the Program Counter, which stores the address of the next instruction to be executed, will be
transferred onto the stack. The Program Counter will then be loaded with a new address which
will be the value of the corresponding interrupt vector. The microcontroller will begin then fetch
its next instruction from this interrupt vector. The instruction at this vector will jump to another
section of program which is known as the interrupt service routine. Here is located the code to
control the appropriate interrupt. The interrupt service routine must be terminated with a RETI
instruction, which retrieves the original Program Counter address from the stack and allows the
microcontroller to continue with normal execution at the point where the interrupt occurred.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Interrupt Priority
Priority Levels
The accompanying table illustrates the interrupt priority level assigned by the corresponding IPnH.
x and IPn.x bits (n=0~3).
IPnH.x
IPn.x
Priority Level
Note
1
1
Level 3
Highest Priority
1
0
Level 2
↓
0
1
Level 1
↓
0
0
Level 0
Lowest Priority
With regard to interrupts which are assigned at the same priority level by the IPnH.x and IPn.x bits,
their actual interrupt priority should be followed by the accompanying table.
Interrupt Source
Rev. 1.10
Interrupt
Vector
Priority Control
Service Priority
Reset
0000H
Always Highest
External Interrupt 0 (INT0)
0003H
PX0H(IP0H.0) / PX0(IP0.0)
↓
Timer 0 Overflow Interrupt
000BH
PT0H(IP0H.1) / PT0(IP0.1)
↓
External Interrupt 1 (INT1)
0013H
PX1H(IP0H.2) / PX1(IP0.2)
↓
Timer 1 Overflow Interrupt
001BH
PT1H(IP0H.3) / PT1(IP0.3)
↓
Timer 2 Overflow Interrupt
or Timer 2 External Reload
Interrupt
002BH
PT2H(IP0H.5) / PT2(IP0.5)
↓
CCU0 Comapre Interrupt
0043H
PCCU0H(IP1H.0) / PCCU0(IP1.0)
↓
CCU1 Comapre Interrupt
004BH
PCCU1H(IP1H.1) / PCCU1(IP1.1)
↓
ADC End of Conversion
Interrupt
0073H
PADCH(IP3H.2) / PADC(IP3.2)
↓
Time Base Overflow Interrupt
007BH
PTBH(IP3H.3) / PTB(IP3.3)
LVD Interrupt
008BH
PLVDH(IP2H.1) / PLVD(IP2.1)
86 of 147
Highest Priority
↓
Lowest Priority
July 31, 2015
Interrupts
Each interrupt source can be individually programmed to one of four priority levels by setting or
clearing bits in the interrupt priority registers: IP0, IP1, IP2, IP3, IP0H, IP1H, IP2H and IP3H.
IP0, IP1, IP2 and IP3 hold the low order priority bits and IP0H, IP1H, IP2H and IP3H hold the
high priority bits for each interrupt. An interrupt service routine in progress can be interrupted by
a higher priority interrupt, but not by another interrupt of the same or lower priority. The highest
priority interrupt cannot be interrupted by any other interrupt source. If two requests of different
priority levels are pending at the end of an instruction, the request of higher priority level is
serviced. If requests of the same priority level are pending at the end of an instruction, an internal
polling sequence determines which request is serviced. The polling sequence is based on the vector
address; an interrupt with a lower vector address has higher priority than an interrupt with a higher
vector address. Note that the polling sequence is only used to resolve pending requests of the same
priority level.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Priority Control Registers
Low byte of Interrupt Priority Register 0: IP0
SFR Address: B8h
Bit
7
6
5
4
3
2
1
0
Name
—
WDTS
PT2
—
PT1
PX1
PT0
PX0
R/W
—
R/W
R/W
—
R/W
R/W
R/W
R/W
POR
—
0
0
—
0
0
0
0
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Interrupts
Bit 7
Bit 6
Unimplemented, read as “0”
WDTS: Watchdog timer reset indication flag
Described elsewhere
PT2: Timer 2 Interrupt priority low
Low order bit for Timer 2 interrupt priority level.
Unimplemented, read as “0”
PT1: Timer 1 Interrupt priority low
Low order bit for Timer 1 interrupt priority level.
PX1: External interrupt 1 priority low
Low order bit for External Interupt 1 interrupt priority level.
PT0: Timer 0 Interrupt priority low
Low order bit for Timer 0 interrupt priority level.
PX0: External interrupt 0 priority low
Low order bit for External Interupt 0 interrupt priority level.
High byte of Interrupt Priority Register 0: IP0H
SFR Address: B9h
Bit
7
6
5
4
3
2
1
0
Name
—
—
PT2H
—
PT1H
PX1H
PT0H
PX0H
R/W
—
—
R/W
—
R/W
R/W
R/W
R/W
POR
—
—
0
—
0
0
0
0
Bit 7~6
Bit 5
Unimplemented, read as “0”
PT2H: Timer 2 Interrupt priority high
High order bit for Timer 2 interrupt priority level.
Bit 4
Unimplemented, read as “0”
Bit 3
PT1H: Timer 1 Interrupt priority high
High order bit for Timer 1 interrupt priority level.
Rev. 1.10
Bit 2
PX1H: External interrupt 1 priority high
High order bit for External Interupt 1 interrupt priority level.
Bit 1
PT0H: Timer 0 Interrupt priority high
High order bit for Timer 0 interrupt priority level.
Bit 0
PX0H: External interrupt 0 priority high
High order bit for External Interupt 0 interrupt priority level.
87 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Low byte of Interrupt Priority Register 1: IP1
SFR Address: E4h
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
PCCU1
PCCU0
R/W
—
—
—
—
—
—
R/W
R/W
POR
—
—
—
—
—
—
0
0
Bit 0
Unimplemented, read as “0”
PCCU1: CCU1 Interrupt priority low
Low order bit for CCU1 interrupt priority level.
PCCU0: CCU0 Interrupt priority low
Low order bit for CCU0 interrupt priority level.
Interrupts
Bit 7~2
Bit 1
High byte of Interrupt Priority Register 1: IP1H
SFR Address: E5h
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
PCCU1H
PCCU0H
R/W
—
—
—
—
—
—
R/W
R/W
POR
—
—
—
—
—
—
0
0
Bit 7~2
Bit 1
Bit 0
Unimplemented, read as “0”
PCCU1H: CCU1 Interrupt priority high
High order bit for CCU1 interrupt priority level.
PCCU0H: CCU0 Interrupt priority high
High order bit for CCU0 interrupt priority level.
Low byte of Interrupt Priority Register 2: IP2
SFR Address: E6h
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
PLVD
—
R/W
—
—
—
—
—
—
R/W
—
POR
—
—
—
—
—
—
0
—
Bit 7~2
Bit 1
Bit 0
Rev. 1.10
Unimplemented, read as “0”
PLVD: LVD Interrupt priority low
Low order bit for LVD interrupt priority level.
Unimplemented, read as “0”
88 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
High byte of Interrupt Priority Register 2: IP2H
SFR Address: E7h
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
PLVDH
—
R/W
—
—
—
—
—
—
R/W
—
POR
—
—
—
—
—
—
0
—
Bit 0
Unimplemented, read as “0”
PLVDH: LVD Interrupt priority high
High order bit for LVD interrupt priority level.
Unimplemented, read as “0”
Interrupts
Bit 7~2
Bit 1
Low byte of Interrupt Priority Register 3: IP3
SFR Address: CEh
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
PTB
PADC
—
—
R/W
—
—
—
—
R/W
R/W
—
—
POR
—
—
—
—
0
0
—
—
Bit 7~4
Bit 3
Unimplemented, read as “0”
PTB: Time Base Interrupt Priority low
Low order bit for Time Base Interrupt Priority level.
Bit 2
PADC: ADC Interrupt priority low
Low order bit for ADC interrupt priority level.
Bit 1~0
Unimplemented, read as “0”
How byte of Interrupt Priority Register 3: IP3H
SFR Address: CFh
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
PTBH
PADCH
—
—
R/W
—
—
—
—
R/W
R/W
—
—
POR
—
—
—
—
0
0
—
—
Bit 7~4
Bit 3
Bit 2
Bit 1~0
Rev. 1.10
Unimplemented, read as “0”
PTBH: Time Base Interrupt Priority high
High order bit for Time Base Interrupt Priority level.
PADCH: ADC Interrupt priority high
High order bit for ADC interrupt priority level.
Unimplemented, read as “0”
89 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
External Interrupt
The IT0 and IT1 bits are used to select the active edge or level that will trigger the external
interrupt for INT0 and INT1 respectively.
External Interrupt Trigger Type
Ext Int
Trigger Type
Register
Bit
INT0
Low Level or Falling Edge
TCON
IT0
INT1
Low Level or Falling Edge
TCON
IT1
A/D Converter Interrupt
The A/D Converter Interrupt is controlled by the termination of an A/D conversion process. An
A/D Converter Interrupt request will take place when the A/D Converter Interrupt request flag,
IADC, is set, which occurs when the A/D conversion process finishes. To allow the program to
branch to its respective interrupt vector address, the global interrupt enable bit, EAL, and A/D
Interrupt enable bit, EADC, must first be set. When the interrupt is enabled, the stack is not full
and the A/D conversion process has ended, a subroutine call to the A/D Converter Interrupt vector,
will take place. When the interrupt is serviced, the A/D Converter Interrupt flag, IADC, will be
automatically cleared. The EAL bit must be cleared by the application program to disable other
interrupts.
Timer/Counter Interrupt
For a Timer Counter interrupt to occur, the global interrupt enable bit, EAL, and the corresponding
timer interrupt enable bit, ETn, must first be set. An actual Timer Counter interrupt will take place
when the Timer Counter request flag, TFn, is set, a situation that will occur when the relevant
Timer Counter overflows. When the interrupt is enabled, the stack is not full and a Timer Counter
n overflow occurs, a subroutine call to the relevant timer interrupt vector, will take place. When the
interrupt is serviced, the timer interrupt request flag, TFn (n=0,1), will be automatically reset, while
the TF2 bit must be cleared by the application program, and the EAL bit must also be cleared using
the application program to disable other interrupts.
In addition, when the Timer 2 works in relode mode 1, a falling edge at the T2EX input pin will
reload the data from CRCH/CRCL registers to TH2/TL2 registers, if the external reload interrupt
control bit, EXEN2, the Timer 2 interrupt control bit, ET2, and the global interrupt enable bit,
EAL, are all set high, a Timer 2 external reload interrupt will generated. When the interrupt is
serviced, the interrupt flag, EXF2, must be cleared using the application program.
Rev. 1.10
90 of 147
July 31, 2015
Interrupts
The external interrupt pins are pin-shared with the I/O pins and can be configured as an external
interrupt pin if the corresponding external interrupt enable bits in the interrupt control registers
have been set. The pin must also be setup as an input by setting the corresponding bits in the port
mode register. Any pull-high resistor settings will also remain valid when the pin is used as an
external interrupt pin. When the interrupt is enabled, the stack is not full and a low level or falling
edge appears on the external interrupt pin, a subroutine call to the external interrupt vector, will
take place. When the interrupt is serviced, the external interrupt request flag will be automatically
reset but the EAL bit must be cleared by the application program to disable other interrupts.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Time Base Interrupts
The purpose of the Time Base Interrupt is to provide an interrupt signal at fixed time periods. Their
clock sources originate from the internal clock source f TBC. This f TBC input clock passes through a
divider, the division ratio of which is selected by programming the appropriate bits in the TBCR
register to obtain longer interrupt periods. The clock source that generates f TBC, which in turn
controls the Time Base interrupt period, can originate from the system clock or the LIRC oscillator.
fSYS/4
fSYS/1�8
M
U
X
fTBC
÷�8~�1�
Time Base Interr�pt
f��K
TBCK[1:0]
Rev. 1.10
TBS[�:0]
91 of 147
July 31, 2015
Interrupts
The function of the Time Base Interrupt is to provide a regular time signal in the form of an
internal interrupt. It is basically a simple timer whose interrupt is generated when it overflows.
When this happen its respective interrupt request flag, TBF will be set. To allow the program to
branch to its respective interrupt vector address, the global interrupt enable bit, EAL and Time
Base enable bit, ETB, must first be set. When the interrupt is enabled, the stack is not full and the
Time Base overflows, a subroutine call to its respective vector locations will take place. When the
interrupt is serviced, the respective interrupt request flag, TBF, will be automatically reset but the
EAL bit must be cleared by the application program to disable other interrupts.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
TBCR Register
SFR Address: B2h
Bit
7
6
5
4
3
2
1
0
Name
TBEN
—
TBCK1
TBCK0
—
TBS2
TBS1
TBS0
R/W
R/W
—
R/W
R/W
—
R/W
R/W
R/W
POR
0
—
0
0
—
1
1
1
TBEN: Time Base Control bit
Bit 6
Bit 5 ~ 4
Unimplemented, read as “0”
TBCK1 ~ TBCK0: Select Time Base clock source, f TBC
Bit 3
Bit 2 ~ 0
Unimplemented, read as “0”
TBS2 ~ TBS0: Select Time Base Time-out Period
Interrupts
Bit 7
0: Disable
1: Enable
00: f SYS/4
01: f SYS/128
1x: f 32K (f 32K is sourced from f LIRC)
000: 256/f TBC
001: 512/f TBC
010: 1024/f TBC
011: 2048/f TBC
100: 4096/f TBC
101: 8192/f TBC
110: 16384/f TBC
111: 32768/f TBC (default setting)
LVD Interrupt
A LVD Interrupt request will take place when the LVD Interrupt request flag, LVDF, is set, which
occurs when the Low Voltage Detector function detects a low power supply voltage. To allow the
program to branch to its respective interrupt vector address, the global interrupt enable bit, EAL,
Low Voltage Interrupt enable bit, ELVD, must first be set. When the interrupt is enabled, the stack
is not full and a low voltage condition occurs, a subroutine call to the Interrupt vector, will take
place. When the Low Voltage Interrupt is serviced, the EAL bit must be cleared by the application
program to disable other interrupts and the LVDF flag will be automatically cleared.
Rev. 1.10
92 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Interrupt Wake-up Function
Programming Considerations
By disabling the interrupt enable bits, a requested interrupt can be prevented from being serviced,
however, once an interrupt request flag is set, it will remain in this condition in the interrupt
register until the corresponding interrupt is serviced or until the request flag is cleared by the
application program.
It is recommended that programs do not use the “CALL subroutine” instruction within the interrupt
subroutine. Interrupts often occur in an unpredictable manner or need to be serviced immediately
in some applications. If only one stack is left and the interrupt is not well controlled, the original
control sequence will be damaged once a “CALL” subroutine is executed in the interrupt
subroutine.
All these interrupt functions have the capability of waking up the microcontroller when in the
IDLE mode, only INT0 and INT1 interrupts can wake up the microcontroller when in the Powerdown mode.
Only the Program Counter is pushed onto the stack. If the contents of the register or status register
are altered by the interrupt service program, which may corrupt the desired control sequence, then
the contents should be saved in advance.
Rev. 1.10
93 of 147
July 31, 2015
Interrupts
Each of the interrupt functions has the capability of waking up the microcontroller when in
the IDLE mode, and among these interrupts only INT0 and INT1 interrupts can wake up the
microcontroller when in the Power-down mode. A wake-up is generated when an interrupt
request flag changes from low to high and is independent of whether the interrupt is enabled or
not. Therefore, even though the device is in the Power-Down or IDLE Mode and the CPU clock
stopped, situations such as external edge transitions on the external interrupt pins, or a low power
supply voltage may cause their respective interrupt flag to be set high and consequently generate
an interrupt. Care must therefore be taken if spurious wake-up situations are to be avoided. If an
interrupt wake-up function is to be disabled then the corresponding interrupt request flag should be
set high before the device enters the Power-Down or IDLE Mode. The interrupt enable bits have no
effect on the interrupt wake-up function.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
25
Input/Output Ports
The devices offer a range of flexible options on their I/O ports. Many pins can be setup with a
choice of different register controlled modes as well as having wake up and slew rate functions.
Input/Output Port Overview
I/O Port Function Summary
Function.
Rev. 1.10
Port Number
P0
P1
P3
Notes
Push-Pull
√
√
√
CMOS Output
Open Drain
√
√
√
NMOS
Quasi Bi-direct
√
√
√
Traditional 8051 Port type
Input Only
√
√
√
High impedance
Bit Addressable
√
√
√
—
Slew Rate Control
√
√
√
Fast or Slow select
94 of 147
July 31, 2015
Input/Output Ports
The devices are provided with a series bidirectional input/output ports labeled with port names P0,
P1 and P3. These I/O ports are mapped to the Special Function Registers with specific addresses
as shown in the Special Function Registers table. All of these I/O ports can be used for both input
and output operations, the data for which is stored in Port Data Registers. Ports P0, P1 and P3 can
be setup using Port Mode Registers to operate in a series of different modes. The Port P0 provides
register controlled wake up function as well. Bit manipulation instructions can be used to control
Ports P0, P1 and P3, and all pins for these ports are equipped with slew rate control.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Register Description
This section provides a description of all the registers associated with I/O setup and control. The
following table gives a summary of all associated I/O registers, which will be described in detail later.
I/O Register List
Bit
7
6
5
4
3
2
1
0
P0WAKE
P07WU
P06WU
P05WU
P04WU
P03WU
P02WU
P01WU
P00WU
P0
P0.7
P0.6
P0.5
P0.4
P0.3
P0.2
P0.1
P0.0
P0M0
P0M0.7
P0M0.6
P0M0.5
P0M0.4
P0M0.3
P0M0.2
P0M0.1
P0M0.0
P0M1
P0M1.7
P0M1.6
P0M1.5
P0M1.4
P0M1.3
P0M1.2
P0M1.1
P0M1.0
P1
—
—
—
P1.4
P1.3
P1.2
P1.1
P1.0
P1M0
—
—
—
P1M0.4
P1M0.3
P1M0.2
P1M0.1
P1M0.0
P1M1.0
P1M1
—
—
—
P1M1.4
P1M1.3
P1M1.2
P1M1.1
P3
P3.7
P3.6
P3.5
P3.4
P3.3
P3.2
P3.1
P3.0
P3M0
P3M0.7
P3M0.6
P3M0.5
P3M0.4
P3M0.3
P3M0.2
P3M0.1
P3M0.0
P3M1
P3M1.7
P3M1.6
P3M1.5
P3M1.4
P3M1.3
P3M1.2
P3M1.1
P3M1.0
SRCR
—
—
—
—
SRCR.3
SRCR.2
SRCR.1
SRCR.0
Each Port has its own data register, known as P0, P1 and P3, which are used to control the input
and output I/O pin data. These registers read input pin data or write output pin data on the selected
I/O pin. For I/O pins setup as outputs a write operation to these registers will setup either a high or
low level on the corresponding pin. For I/O pins setup as inputs a read operation to these registers
will read the actual logic level on the corresponding pin.
P0 Register
SFR Address: 80h
Bit
7
6
5
4
3
2
1
0
Name
P0.7
P0.6
P0.5
P0.4
P0.3
P0.2
P0.1
P0.0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
1
1
1
1
1
1
1
1
P1 Register
SFR Address: 90h
Rev. 1.10
Bit
7
6
5
4
3
2
1
0
Name
P1.7
P1.6
P1.5
P1.4
P1.3
P1.2
P1.1
P1.0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
1
1
1
1
1
1
1
1
95 of 147
July 31, 2015
Input/Output Ports
Register
Name
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
P3 Register
SFR Address: B0h
Bit
7
6
5
4
3
2
1
0
Name
P3.7
P3.6
P3.5
P3.4
P3.3
P3.2
P3.1
P3.0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
1
1
1
1
1
1
1
1
Bit 7~0
PnM0/PnM1 Registers – Port Mode Registers
They are used to setup the I/O operating mode of each pin. As there are four different operating
modes for the Port 0~3 pins, each pin has two bits to select the mode, known as the PnM0 and
PnM1 bits.
Port 0 Mode Control
P0M0 Register
SFR Address: 9Eh
Bit
7
6
5
4
3
2
1
0
Name
P0M0.7
P0M0.6
P0M0.5
P0M0.4
P0M0.3
P0M0.2
P0M0.1
P0M0.0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
P0M1 Register
SFR Address: 9Fh
Rev. 1.10
Bit
7
6
5
4
3
2
1
0
Name
P0M1.7
P0M1.6
P0M1.5
P0M1.4
P0M1.3
P0M1.2
P0M1.1
P0M1.0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
96 of 147
July 31, 2015
Input/Output Ports
I/O Port bit 7 ~ bit 0 Input/Output Data Control
During reading and writing of data to these registers, what actually happens is
dependent upon whether the corresponding pin is setup as an output or input.
Register Write Operations
A write operation is only effective when the corresponding pin is setup as an output. In
such cases a write operation will setup the logic level on the pin as follows:
0: Output low
1: Output high
Register Read Operations
A read operation will read the current logic level on the corresponding pin.
0: Read low level
1: Read high level
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Port 1 Mode Control
P1M0 Register
SFR Address: A6h
Bit
7
6
5
4
3
2
1
0
Name
P1M0.7
P1M0.6
P1M0.5
P1M0.4
P1M0.3
P1M0.2
P1M0.1
P1M0.0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit
7
6
5
4
3
2
1
0
Name
P1M1.7
P1M1.6
P1M1.5
P1M1.4
P1M1.3
P1M1.2
P1M1.1
P1M1.0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Port 2 Mode Control
P2M0 Register
SFR Address: AEh
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
—
P2M0.0
R/W
—
—
—
—
—
—
—
R/W
POR
—
—
—
—
—
—
—
0
P2M1 Register
SFR Address: AFh
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
—
P2M1.0
R/W
—
—
—
—
—
—
—
R/W
POR
—
—
—
—
—
—
—
0
Port 3 Mode Control
P3M0 Register
SFR Address: B6h
Bit
7
6
5
4
3
2
1
0
Name
P3M0.7
P3M0.6
P3M0.5
P3M0.4
P3M0.3
P3M0.2
P3M0.1
P3M0.0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
P3M1 Register
SFR Address: B7h
Rev. 1.10
Bit
7
6
5
4
3
2
1
0
Name
P3M1.7
P3M1.6
P3M1.5
P3M1.4
P3M1.3
P3M1.2
P3M1.1
P3M1.0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
97 of 147
July 31, 2015
Input/Output Ports
P1M1 Register
SFR Address: A7h
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
These registers operate as pairs, for example P0M0 and P0M1, to select the operating mode for
each I/O pin. The following table shows how the PnM0 and PnM1 bits are used to select the I/O
operating mode.
PnM1.m
0
0
Quasi-bidirectional
Configuration of Port n.m
0
1
Push-Pull Output
1
0
Input-Only – High Impedance Input
1
1
Open-Drain Output
Input/Output Ports
PnM0.m
Note: n=0~3 which selects Port 0 to Port 3
m=0~7 which selects the port pin
P0WAKE Register – Port 0 Wake-up
P0WAKE Register
SFR Address: 91h
Bit
7
6
5
4
3
2
1
0
Name
P07WU
P06WU
P05WU
P04WU
P03WU
P02WU
P01WU
P00WU
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
P0WAKE: Port 0 bit 7 ~ bit 0 Wake-up Control
0: Disable
1: Enable
When the device enters the IDLE or Power-Down Mode, the system clock will stop resulting in
power being conserved, a feature that is important for battery and other low-power applications.
Various methods exist to wake-up the microcontroller, one of which is to change the logic condition
on one of the P0.0~P0.7 pins to a low level. Note that the Port 0 wake-up functions are triggered
by a low logic level and not by a falling edge. This Port 0 wake-up function is especially suitable
for applications that can be woken up via external switches. The P0 wake up pins can be selected
individually to have this wake-up feature using the P0WAKE register.
Bit 7~0
Rev. 1.10
98 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
SRCR Register – Slew Rate Control
SRCR Register
SFR Address: A4h
Bit
7
6
5
4
3
2
1
0
Label
—
—
—
—
SRCR.3
SRCR.2
SRCR.1
SRCR.0
R/W
—
—
—
—
R/W
R/W
R/W
R/W
POR
—
—
—
—
0
0
0
0
Unimplemented, read as “0”
SRCR.3: Port 3 Slew Control Enable
0: Fast
1: Slow
Bit 2
SRCR.2: Port 2 Slew Control Enable
0: Fast
1: Slow
Bit 1
SRCR.1: Port 1 Slew Control Enable
0: Fast
1: Slow
Bit 0
SRCR.0: Port 0 Slew Control Enable
0: Fast
1: Slow
The port pins, when setup as outputs, can be selected to have either a fast or slow slew rate. To
minimise noise generation due to fast switching of the output drivers, it may be advisable to select
the slower slew rate. The slew rates are selected port wide, individual pins cannot be selected to
have either fast or slow slew rates.
Pin-remapping Function
The limited number of supplied pins in a package can impose restrictions on the amount of
functions a certain device can contain. However by allowing the same pins to share several
different functions and providing a means of function selection, a wide range of different functions
can be incorporated into even relatively small package sizes.
PRM Register – Pin-remapping Control Register
PRM Register
SFR Address: D5h
Bit
7
6
5
4
3
2
1
0
Label
—
—
—
—
—
—
—
PRM0
R/W
—
—
—
—
—
—
—
R/W
POR
—
—
—
—
—
—
—
0
Bit 7~1
Bit 0
Rev. 1.10
Unimplemented, read as “0”
PRM0: CC3~CC0 pin-remapping selection bit
0: CC1 on P3.1, CC0 on P3.0
1: CC1 on P1.0, CC0 on P0.7
99 of 147
July 31, 2015
Input/Output Ports
Bit 7~4
Bit 3
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
I/O Pin Structures
The accompanying diagrams illustrate the internal structures of some generic I/O pin types. As
the exact logical construction of the I/O pin will differ from these drawings, they are supplied as a
guide only to assist with the functional understanding of the I/O pins.
Quasi-bidirectional I/O
A Very Weak pull high resistor will be turned on whenever the I/O port registers, associated with
the I/O pins, contain a high level.
When the I/O port register bits have a high level and the corresponding I/O pins stay at high level
as well, the Weak pull high resistor will be turned on. However, if the I/O port registers are high
and the corresponding I/O pins are pulled low by the external devices, then the Weak pull high
resistor will be disabled by hardware. These weak pull-high resistors enable/disable function are
dependant on the voltage level after the I/O pin is connected to the external circuit.
The Strong pull high resistor is used to enhance the output response time. When the output state
changes from low to high, the Strong resistor will be turned on after two system clock delay times.
A Quasi-bidirectional pin also provides a Schmitt Trigger input.
VCC
Two System
Clock Delay
Strong
VCC
Very Weak
VCC
Weak
Port
Pin
Q
Port Register Data
Input
Data
Quasi-bidirectional I/O Structure
Rev. 1.10
100 of 147
July 31, 2015
Input/Output Ports
This is the traditional 8051 type I/O port type, constructed from an NMOS FET transistor and
three pull high resistors, so called Strong, Weak, Very Weak pull high resistors. This structure can
be used to reduce the power consumption and the output switching state respond time.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Push-pull Output
This I/O structure is a standard CMOS type structure with a single NMOS and PMOS
complimentary transistor pair. The input is a Schmitt Trigger type input.
VCC
Input/Output Ports
Strong
Port
Pin
Q
Port Register Data
Input
Data
Push-pull Output Structure
Open-drain Output
This I/O structure is an open drain type structure with a Schmitt Trigger input. Usually, an external
pull high resistor is needed for such applications.
Port
Pin
Q
Port Register Data
Input
Data
Open-drain Output Structure
Input Only
This Input Only structure is a Schmitt Trigger type input without any pull high resistors.
Input
Data
Port
Pin
Input Only Structure
Rev. 1.10
101 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Programming Considerations
Within the user program, one of the first things to consider is port initialisation. After a reset, the I/
O data register will be set high and I/O port mode registers will be cleared to low. This means that
all I/O pins will default to a Quasi-bidirectional structure. The I/O pins can be re-assigned to some
other mode for each I/O using the control registers, PnM0 and PnM1. Ports P0, P1 and P3 provide
four I/O structure modes option. Care should be taken to setup the correct I/O structure for each I/
O pin, otherwise unexpected data will be input or output on the I/O pins.
If any pins are setup to be used as A/D input pins then it is important to ensure that the I/O Port
Mode registers setup the pins as inputs, which are essentially high impedance inputs. In this way
the I/O logic circuits will have a minimal influence on the A/D input impedance.
When using these bit control instructions, a read-modify-write operation takes place. The
microcontroller must first read in the data on the entire port, modify it to the required new bit
values and then rewrite this data back to the output ports, such as using CLR or SETB bit write
instructions. Care should be taken that some instructions, the Read-Modify-Write instructions,
operate on the Pn register, such as “INC P0” or “ANL P1, A”, while others can operate directly onto
the external port input, such as “MOV A, P1”.
The accompanying table illustrates the Read-Modify-Write related instructions.
Mnemonic
Rev. 1.10
Instruction
Example
Bit Manipulation
ANL
Logical AND
ANL P3, A
—
ORL
Logical OR
OR P3, A
—
XRL
Logical XOR
XRL P3, A
—
JBC
Jump if bit set and then clear bit
JBC P3.0, (LABEL)
—
CPL
Complement bit
CPL P3.0
—
INC
Increment
INC P3
—
DEC
Decrement
DEC P3
—
DJNZ
Decrement and jump if not zero
DJNZ P3, (LABEL)
—
MOV Px.y, C
Move carry flag to Bit y of Port x
MOV P3.0, C
√
CLR Px.y
Clear Bit y of Port x
CLR P3.0
√
SETB Px.y
Set Bit y of Port x
SETB P3.0
√
102 of 147
July 31, 2015
Input/Output Ports
The data registers, P0, P1 and P3, reflect the value of the corresponding I/O port, however, they do
not necessarily reflect the I/O pin logic state. During reading and writing of data to these registers,
what actually happens is dependent upon whether the corresponding pin is setup as an output or
input. A write operation is only effective when the corresponding pin is setup as an output. In such
cases a write operation will setup the logic level, low or high, on the pin. A read operation will read
the current logic level, low or high, on the corresponding pin.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
26
Timer/Event Counters
Timer/Event Counter Summary
The devices contain three Timers, namely Timer 0, Timer 1 and Timer 2. Each individual Timer is
16-bit wide which are composed of two 8-bit registers, TLn and THn. Timers 0 and Timer 1 have
similar structures and similar operating modes. Timer 2 has a different structure and is also known
as a Programmable Counter Array, or PCA for short and has functions such as Compare, Reload
and Capture functions, so called CRC, as well as programmable clock output function. All timers
have a clock divider which provides additional range to the timers.
Various Timer control registers determine how each Timer is operated. The clock sources for the
Timers can come from an internal clock source or from an external timer pin. Note that if the
external timer input function is selected, the respective pin-shared I/O pins should be configured as
input pins.
As Timer 0 and 1 have similar structures they will be described together in their own single
chapter, however as Timer 2 has a very different structure it will be described in a separate chapter.
The main features and differences among the Timers are summarised in the accompanying table.
Timer Function Summary
Function
Rev. 1.10
Timer 0
Timer 1
Timer 2
13-bit Timer/Counter
√
√
—
16-bit Timer/Counter
√
√
—
8-bit timer with auto-reload
√
√
—
Two 8-bit Timer/Counters
√
—
—
16-bit Timer/Counter with auto-reload
—
—
√
16-bit Timer/Counter with capture
—
—
√
Compare Match Output
—
—
√
Programmable Clock Output
—
—
√
103 of 147
July 31, 2015
Timer/Event Counters
One of the most fundamental functions in any microcontroller device is the ability to control and
measure time. To implement time related functions each device includes several Timer/Counters.
The Timers are multi-purpose timing units and serve to provide operations such as Timer/Counter,
Input Capture, Compare Match Output and Programmable Clock Output. Each of the Timers has
one individual interrupt. The addition of input and output pins for each Timer ensures that users
are provided with timing units with a wide and flexible range of features.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
27
Timer/Event Counters 0, 1
These two timers provide have a similar type and structure and operate with a choice of three
modes for Timer 1 and four modes for Timer 0. They provide basic timing and event counting
operations.
The different operating modes of the timers are selected using the TnM1 and TnM0 bits in the
TMOD.
Timer Mode
TnM1, TnM0 bits
0
00
13-bit Timer-Counter
Mode Name
Application Timer
Timer 0, 1
1
01
16-bit Counter
Timer 0, 1
2
10
8-bit Counter Auto Reload
3
11
Two 8-bit Counters
Timer 0, 1
Timer 0 only
The registers, THn and TLn, are special function registers located in the Special Function Registers
and is the place where the actual timer value is stored. This register pair, are each 8-bit wide, and
can be cascaded into 13-bit or 16-bit wide using mode options. The value in the timer registers
increases by one each time an internal clock pulse is received or an external transition occurs on
the external timer pin. The timer will count from the initial value loaded by the preload register to
their full count at which point the timer overflows and an internal interrupt signal is generated. If
the timer auto-reload mode is selected, the timer value will then be reset with the initial preload
register value and continue counting, otherwise the timer value will be reset to zero. Note that to
achieve a maximum full range count, the preload register must first be cleared to all zeros.
Timer 0/Timer 1Register Description
Overall operation of the Timer 0 and Timer 1 are controlled using the registers listed in the
accompanying table. A register pair, TLn and THn, exist to store the internal counter 13-bit or 16bit value. The TCON, IRCON, IEN0, IEN1 registers include the TIMERn interrupt control and
interrupt request flags, which are described in the Interrupt section. The remaining registers are
control registers which setup the different operating and control modes as well as the clock source
control bits.
Timer0/Timer1 Register List
Bit
Register
Name
7
6
5
4
3
2
1
0
IEN0
EAL
WDT
ET2
—
ET1
EX1
ET0
EX0
ECCU0
IEN1
EXEN2
SWDT
—
—
—
—
ECCU1
IRCON
EXF2
TF2
—
—
CCU1F
CCU0F
—
—
TMOD
GATE1
C/T1
T1M1
T1M0
GATE0
C/T0
T0M1
T0M0
TCON
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
TLn
D7
D6
D5
D4
D3
D2
D1
D0
THn
D15
D14
D13
D12
D11
D10
D9
D8
TMPRE
—
—
T2PRE1
T2PRE0
T1PRE1
T1PRE0
T0PRE1
T0PRE0
Note: n=0, 1
Rev. 1.10
104 of 147
July 31, 2015
Timer/Event Counters 0, 1
Introduction
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
TL0 Register
SFR Address: 8Ah
16-bit
Bit
7
6
5
4
3
2
1
0
Name
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
TL0: TIMER0 Counter Low Byte Register bit 7 ~ bit 0
13-bit
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
D4
D3
D2
D1
D0
R/W
—
—
—
R/W
R/W
R/W
R/W
R/W
POR
—
—
—
0
0
0
0
0
Bit 7~5
Bit 4~0
Unimplemented, read as “0”
TL0: TIMER0 Counter Low Byte Register bit 4 ~ bit 0
TH0 Register
SFR Address: 8Ch
16-bit
Bit
7
6
5
4
3
2
1
0
Name
D15
D14
D13
D12
D11
D10
D9
D8
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
TH0: TIMER0 Counter High Byte Register bit 15~bit 8
13-bit
Bit
7
6
5
4
3
2
1
0
Name
D12
D11
D10
D9
D8
D7
D6
D5
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
Rev. 1.10
TH0: TIMER0 Counter High Byte Register bit 12 ~ bit 5
105 of 147
July 31, 2015
Timer/Event Counters 0, 1
Bit 7~0
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
TL1 Register
SFR Address: 8Bh
16-bit
Bit
7
6
5
4
3
2
1
0
Name
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
TL1: TIMER1 Counter Low Byte Register bit 7 ~ bit 0
13-bit
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
D4
D3
D2
D1
D0
R/W
—
—
—
R/W
R/W
R/W
R/W
R/W
POR
—
—
—
0
0
0
0
0
Bit 7~5
Bit 4~0
Unimplemented, read as “0”
TL1: TIMER1 Counter Low Byte Register bit 4 ~ bit 0
TH1 Register
SFR Address: 8Dh
16-bit
Bit
7
6
5
4
3
2
1
0
Name
D15
D14
D13
D12
D11
D10
D9
D8
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
TH1: TIMER1 Counter High Byte Register bit 15~bit 8
13-bit
Bit
7
6
5
4
3
2
1
0
Name
D12
D11
D10
D9
D8
D7
D6
D5
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
Rev. 1.10
TH1: TIMER1 Counter High Byte Register bit 12 ~ bit 5
106 of 147
July 31, 2015
Timer/Event Counters 0, 1
Bit 7~0
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
TMOD Register
SFR Address: 89h
Bit
7
6
5
4
3
2
1
0
Name
GATE1
C/T1
T1M1
T1M0
GATE0
C/T0
T0M1
T0M0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7
Bit 5~4
Bit 3
Bit 2
Bit 1~0
Rev. 1.10
107 of 147
July 31, 2015
Timer/Event Counters 0, 1
Bit 6
GATE1: Timer 1 Gate Control
0: Disable
1: Enable
This bit is used to enable the Timer 1 Gate function. When the GATE1 bit is set high
and Timer 1 is enabled to run using the TR1 bit and when the INT1 pin is input high,
then the Timer 1 Counter will increment one on every falling edge on the T1 input pin.
C/T1: Timer 1 Counter/Timer selection
0: Timer
1: Counter
T1M1, T1M0: Timer 1 mode selection
00: Mode 0 – 13-bit Timer/Counter
01: Mode 1 – 16-bit Timer/Counter
10: Mode 2 – 8-bit Auto Reload Timer/Counter
11: Mode 3 – Timer Stopped
GATE0: Timer 0 Gate Control
0: Disable
1: Enable
This bit is used to enable the Timer 0 Gate function. When the GATE0 bit is set high
and Timer 0 is enabled to run using the TR0 bit and when the INT0 pin is input high,
then the Timer 0 Counter will increment one on every falling edge on the T0 input pin.
C/T0: Timer 0 Counter/Timer selection
0: Timer
1: Counter
T0M1, T0M0: Timer 0 mode selection
00: Mode 0 – 13-bit Timer/Counter
01: Mode 1 – 16-bit Timer/Counter
10: Mode 2 – 8-bit Auto Reload Timer/Counter
11: Mode 3 – Two independent 8-bit Timer/Counters
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
TCON Register
SFR Address: 88h
Bit
7
6
5
4
3
2
1
0
Name
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7
TF1: Timer 1 interrupt request flag
Bit 5
This bit will be cleared by hardware automatically when the interrupt is processed.
TR1: Timer 1 Run control
0: Stop
1: Run
TF0: Timer 0 interrupt request flag
Bit 4
This bit will be cleared by hardware automatically when the interrupt is processed.
TR0: Timer 0 Run control
Bit 6
Bit 3
Bit 2
Bit 1
Bit 0
0: No request
1: Interrupt request
0: Stop
1: Run
IE1: External interrupt 1 request flag
Described elsewhere
IT1: External interrupt 1 type control
Described elsewhere
IE0: External interrupt 0 request flag
Described elsewhere
IT0: External interrupt 0 type control
Described elsewhere
Rev. 1.10
108 of 147
July 31, 2015
Timer/Event Counters 0, 1
0: No request
1: Interrupt request
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
TMPRE Register
SFR Address: 8Fh
Bit
7
6
5
4
3
2
1
0
Name
—
—
T2PRE1
T2PRE0
T1PRE1
T1PRE0
T0PRE1
T0PRE0
R/W
—
—
R/W
R/W
R/W
R/W
R/W
R/W
POR
—
—
0
0
0
0
0
0
Bit 3~2
Bit 1~0
Unimplemented, read as “0”
T2PRE1, T2PRE0: Timer 2 Clock Frequency selection
00: f SYS/12
01: f SYS/6
10: f SYS/4
11: f SYS
T1PRE1, T1PRE0: Timer 1 Clock Frequency selection
00: f SYS/12
01: f SYS/6
10: f SYS/4
11: f SYS
T0PRE1, T0PRE0: Timer 0 Clock Frequency selection
00: f SYS/12
01: f SYS/6
10: f SYS/4
11: f SYS
Timer/Event Counters 0, 1
Bit 7~6
Bit 5~4
Mode 0 – 13-bit Counter/Timer Mode Operation
To select this mode, bits TnM1 and TnM0, should be set to “00”. The 13 bits of data are comprised
of 5 low bits in the TLn register and 8 high bits in the THn register. The C/Tn bit is used to select
the timer or counter function. The Counter/Timer Run or Stop operation is controlled using the
TRn bit. If the Counter function is selected, the TRn and GATEn bits can be used to manage the
external INTn input to count edge transitions or measure pulse widths. The timer/counter clock
source is decided by the TnPRE0 and TnPRE1 bits in the TMPRE register. Note that the TRn bit
is used to control the Timer/Counter run or stop function. Clearing this bit will not clear the TLn
and THn registers, the registers should be initialised by the application program. When an overflow
occurs, the TFn interrupt request flag will be set and an interrupt will take place if the interrupt is
enabled.
13-bit Counter Data
Bit
Register
Name
7
6
5
4
3
2
1
0
THn
D12
D11
D10
D9
D8
D7
D6
D5
TLn
—
—
—
D4
D3
D2
D1
D0
Note: n=0, 1
Rev. 1.10
109 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Mode 1 – 16-bit Counter/Timer Mode Operation
The following block illustrates the 13-bit and 16-bit Timer/Counter basic operational blocks.
fSYS
fSYS/4
Presca�er
fSYS
fSYS/6
MUX
C/Tn=0
fSYS/1�
Mode 0
/
TnPRE[1:0]
Tn
C/Tn=1
Mode 1
TnM1/TnM0 = 00
THn
D1�
D11
TLn
-
D10
-
D9
D4
D8
D�
D7
D�
D6
D1
D�
D0
TnM1/TnM0 = 01
THn
D1�
D14
TLn
D7
D6
D1�
D�
D1�
D4
D11
D�
D10
D�
D9
D1
D8
D0
Interr�pt
TFn f�ag
TRn
GATEn
INTn
Mode 0 and Mode 1 Block Diagram – Timer 0, 1
Rev. 1.10
110 of 147
July 31, 2015
Timer/Event Counters 0, 1
To select this mode, bits TnM1 and TnM0, should be set to “01” respectively. The 16 bits of data are
stored in the TLn and THn registers. The C/Tn bit is used to select the timer or counter function.
The Counter/Timer Run or Stop is controlled by TRn bit. If the Counter function is selected, the
TRn and GATEn bits can be used to manage the external INTn input to count edge transitions
or measure pulse widths. The timer/counter clock source is decided by the TnPRE0 and TnPRE1
bits in the TMPRE register. Note that the TRn bit is used to control the Timer/Counter run or
stop function. Clearing this bit will not clear the TLn and THn registers, the registers should be
initialised by the application program. When an overflow occurs, the TFn interrupt request flags
will be set and an interrupt will take place if the interrupt is enabled.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Mode 2 – 8-bit Auto-reload Counter/Timer Mode Operation
fSYS
fSYS/4
Presca�er
fSYS
fSYS/6
MUX
C/Tn=0
fSYS/1�
/
TLn Register
TnPRE[1:0]
Interr�pt
TFn f�ag
C/Tn=1
Tn
TRn
A�to-re�oad
GATEn
INTn
THn Register
Mode 2 Block Diagram – Timer 0, 1
Rev. 1.10
111 of 147
July 31, 2015
Timer/Event Counters 0, 1
To select this mode, bits TnM1 and TnM0, should be set to “10” respectively. This function is
implemented by the 8-bit TLn and THn registers. The C/Tn bit is used to select the timer or counter
function. The Counter/Timer Run or Stop is controlled by the TRn bit. If the Counter function is
selected, the TRn and GATEn bits can be used to manage the external INTn input to count edge
transitions or measure pulse widths. The timer/counter clock source is decided by the TnPRE0 and
TnPRE1 registers in the TMPRE register. When the values in the TLn register overflows, the TLn
value will be auto-reloaded with the data in the THn register and an interrupt will take place if the
interrupt is enabled. Note that the value of THn register should be initialised by the application
program. The accompanying block diagram illustrates the 8-bit Auto-Reload Timer/Counter basic
operational blocks.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Mode 3 – Two 8-Bit Timers/Counters Mode Operation – Timer 0 Only
In addition to TL0, the other 8-bit timer, TH0, can use the TR1 bit to enable the Timer. If the TH0
timer overflows, an interrupt will be generated and the interrupt request flag, TF1, will be set high.
The timer clock source is decided by the T0PRE0 and T0PRE1 bits in the TMPRE register. The
following block illustrates the two 8-bit Timer/Counters basic operational blocks.
TR1
fSYS
fSYS/4
Presca�er
fSYS
fSYS/6
MUX
TH0
Interr�pt TF1 f�ag
C/T0=0
fSYS/1�
/
TL0
T0PRE[1:0]
T0
Interr�pt TF0 f�ag
C/T0=1
TR0
GATE0
INT0
Mode 3 Block Diagram – Timer 0
Rev. 1.10
112 of 147
July 31, 2015
Timer/Event Counters 0, 1
To select this mode, bits T0M1 and T0M0, should be set to “11” respectively. This mode is only
available for Timer 0. For Timer 1, this mode is not available and if selected will stop the timer
function. The two 8-bit Timer/Counter function is implemented by the two individual 8-bit TL0
and TH0 registers. TL0 can have both Timer and Counter functions while TH0 can only have a
Timer function. The C/T0 bit is used to select the timer or counter function for TL0. The TL0 Run
or Stop is controlled by the TR0 bit. If the Counter function is selected, the TR0 and GATE0 bits
can be used to manage the external INTn input to count external edge transitions or to measure
input pulse widths. If the TL0 counter overflows, an interrupt will be generated and the interrupt
request flag, TF0, will be set high. The timer/counter clock source is decided by the T0PRE0 and
T0PRE1 bits in the TMPRE register.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
28
Timer 2 with Additional 2-channel PCA
The structure of Timer 2 is very different from that of Timers 0 and 1 and is therefore described in
its own chapter.
Introduction
Timer 2 with PCA Modules Operating Modes Summary
Module
Compare
Capture
Reload
Clock Output
0
√
√
√
√
1
√
√
—
—
Note: Module 0 only provides the reload value from the Timer 2 capture registers CRCH and CRCL
for Clock Output Mode. It is important to note that the actual Clock Output pin is T2 and not CC0.
Timer 2 with PCA Modules I/O Pins
Function
Input Pins
Output Pins
Compare
Reload trigger
Capture
Rev. 1.10
—
CC0, CC1
T2EX
—
CC0, CC1
—
Event Counter or Gated input
T2
—
Clock Output
—
T2
113 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
The Timer 2 provides the Timer, Event Counter, Gated timer functions and also cooperates with
a 2-channel Programmable Counter Array, known as PCA, to implement the Compare, Reload,
Capture and Programmable Clock Output functions. Each channel has a module, so there are four
modules, named Module 0~Module 1. Each module can be operated as a Compare and Capture
function while Module 0 can also be operated as a Compare, Reload, Capture, known as CRC, and
Programmable Clock Output functions. The accompanying tables and diagram illustrate the PCA
modules functional compare table, timer I/O pin list and basic operational block diagram.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
EXF�
Interr�pt
Req�est
EXEN�
Transition
Detector
Re�oad
Module 0
Re�oad
Capt�re
CRCL/CRCH
Match
Overf�ow
TF�
Interr�pt
Req�est
CC0/P3.0
Comparator
T2
Timer 2
TH2/TL2
fSYS
I/O
Contro�
Match
Comparator
CC1/P3.1
Capt�re
Presca�er
& M�x
Module 1
T�I[1:0]
CCL1/CCH1
T�PRE[1:0]
: Latch
Timer 2 with PCA Modules Block Diagram
Timer 2
Timer 2 is a 16-bit wide count-up counter which is driven by a user selectable internal or external
clock source. The counter is composed of two registers, TL2 and TH2, to implement the Timer,
event counter and gated timer functions. The clock source is decided by the bits T2I1 and T2I0 in
the T2CON register.
Timer function
To select this function, bits T2I1 and T2I0 in the T2CON register, should be set to “01” respectively.
The value in the Timer 2 registers, TL2 and TH2, increases by one each time an internal clock
pulse is received. The count rate is derived from the “f SYS”. The prescaler can be managed by
the T2PRE1 and T2PRE0 bits in the TMPRE register. When the timer counter is overflowed, an
interrupt will take place and the interrupt request flag, TF2, will be set to high.
Event Counter function
To select this function, bits T2I1 and T2I0 in the T2CON register, should be set to “10” respectively.
The value in the Timer 2 registers, TL2 and TH2, increases by one each time a falling edge occurs
on the external timer pin, T2. When the timer counter is overflowed, an interrupt will take place
and the interrupt request flag, TF2, will be set to high. The maximum count rate is 1/4 of the
system clock frequency.
Rev. 1.10
114 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
T2EX
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Gated Timer function
Timer 2 with PCA
Time 2 and 4-channel PCA modules provide the Compare, Reload, Capture and programmable
clock output functions. Each of the two Timer 2 Modules contains a pair of registers, CRCL/CRCH
for Module 0 and CCL1/CCH1 for Modules 1. These registers are compared with the Timer 2 TL2/
TH2 register pair and when a compare match occurs, an interrupt signal can be generated. The
value in the Timer 2 registers increases by one each time an internal clock pulse is received or an
external transition occurs on the external timer pin.
The Compare function provides two modes, Mode 0 and Mode 1. When a compare match takes
place, the compare results will output to the respective output pins, according to the selected mode.
Refer Compare mode section for details.
There are two modes for the Capture function, Mode 0 and Mode 1, which are used to select
different trigger methods. In Mode 0, the Capture function is triggered by the external I/O pins,
CCn. In Mode 1, the Capture function is triggered by writing data to the CCL1 or CRCL registers.
Once the Capture function is enabled and triggered, the Timer 2 data in the TL2 and TH2 registers
will be captured into the respective CCL1/CCH1 or CRCL/CRCH registers. Refer Capture modes
for details.
In the Reload mode, the timer counter registers, TH2 and TL2, are located in the Special Function
Registers and is the place where the actual timer value is stored. The value in the timer registers
increases by one each time an internal clock pulse is received or an external transition occurs on
the external timer pin, T2. The timer will count from the initial value loaded by the preload register
to the full count of FFFFH for the 16-bit Timer/Event Counters, at which point the timer overflows
and an internal interrupt signal is generated. There are two modes to reload the CRCL/CRCH
registers data, one is the counter overflow and the other is triggered by the falling edge on the
T2EX pin. Refer Reload mode for details.
In the Programmable Clock Output mode, the clock output frequency depends on the system
clock and the reload value of the Timer 2 capture registers, CRCH and CRCL. The output clock
is generated by programming the T2CON control bit, and output via T2 pin. Refer Programmable
Clock Output mode for details.
Rev. 1.10
115 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
To select this function, bits T2I1 and T2I0 in the T2CON register, should be set to “11” respectively.
The value in the Timer 2 registers, TL2 and TH2, increases by one each time an internal clock
pulse is received. The count rate is derived from the “f SYS” and the prescaler can be managed by
the T2PRE1 and T2PRE0 bits in the TMPRE register. The external timer pin, T2, can be a gate to
the Timer 2 input. When the T2 pin is set high, the Timer 2 keeps counting and when the T2 pin
is cleared to low, the Timer 2 will be stopped. The T2 input signal will be sampled once by every
internal system clock. When the timer counter is overflowed, an interrupt will take place and the
interrupt request flag, TF2, will be set to high.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Timer 2 Register Description
The Timer 2 value is stored in a register pair, TL2/TH2. Each of the internal PCA modules has a
register pair, known as CRCL/CRCH for Module 0 and CCL1/CCH1 for module 1. The T2CON
register is related to the interrupt control register which is described in the Interrupt section. The
remaining two registers, CCEN and T2CON1, are control registers which setup the different
operating and control modes. The following table provides a register summary list for Timer 2.
Bit
Register
Name
7
6
5
4
3
2
1
0
TL2
D7
D6
D5
D4
D3
D2
D1
D0
TH2
D15
D14
D13
D12
D11
D10
D9
D8
CRCL
D7
D6
D5
D4
D3
D2
D1
D0
CRCH
D15
D14
D13
D12
D11
D10
D9
D8
CCL1
D7
D6
D5
D4
D3
D2
D1
D0
CCH1
D15
D14
D13
D12
D11
D10
D9
D8
T2CON
—
I3FR
—
T2R1
T2R0
T2CM
T2I1
T2I0
T2CON1
—
—
—
—
T2OI
T2OE
—
—
CCEN
—
—
—
—
COCAH1
COCAL1
COCAH0
COCAL0
Note: n =1, 2, 3
CCEN Register
SFR Address: C1h
Rev. 1.10
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
COCAH1
COCAL1
COCAH0
COCAL0
R/W
—
—
—
—
R/W
R/W
R/W
R/W
POR
—
—
—
—
0
0
0
0
Bit 7~4
Bit 3~2
Unimplemented, read as “0”
COCAH1, COCAL1: Compare/Capture mode select for Module 1 CC1 register
Bit 1~0
COCAH0, COCAL0: Compare/Capture mode select for Module 0 CRC register
00: Disable
01: Capture on rising edge at the CC1 pin
10: Compare mode
11: Capture on writing data into register CCL1
00: Disable
01: Capture on rising or falling edge at the CC0 pin
10: Compare mode
11: Capture on writing data into register CRCL
116 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
Timer 2 Register List
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
T2CON Register
SFR Address: C8h
Bit
7
6
5
4
3
2
1
0
Name
—
I3FR
—
T2R1
T2R0
T2CM
T2I1
T2I0
R/W
—
R/W
—
R/W
R/W
R/W
R/W
R/W
POR
—
0
—
0
0
0
0
0
Bit 2
Unimplemented, read as “0”
I3FR: Timer 2 Capture Mode 0 edge selection for “CC0”
0: Falling edge
1: Rising edge
This bit is used as capture signal in CC0. When Timer 2 is selected as compare mode 0,
the I3FR bit is recommended to be set high by application program.
Unimplemented, read as “0”
T2R1, T2R0: Timer 2 reload mode selection
00: Reload function disabled
01: Reload function disabled
10: Mode 0
11: Mode 1
T2CM: Timer 2 Compare mode selection
Bit 1~0
T2I1, T2I0: Timer 2 clock source select
Bit 5
Bit 4~3
0: Mode 0
1: Mode 1
00: Timer 2 stopped
01: Internal clock source, decided by the T2PRE1 and T2PRE0 bits in the TMPRE register.
10: External T2 pin falling edge clock source.
11: Internal clock source, decided by the T2PRE1 and T2PRE0 bits, gated by the external T2 pin.
T2CON1 Register
SFR Address: FEh
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
T2OI
T2OE
—
—
R/W
—
—
—
—
R/W
R/W
—
—
POR
—
—
—
—
1
0
—
—
Bit 7~4
Bit 3
Bit 2
Bit 1~0
Rev. 1.10
Unimplemented, read as “0”
T2OI: Timer 2 output initial state control
0: T2 pin initial output Low
1: T2 pin initial output High
The Timer 2 output initial state can be selected by the T2OI bit before enable the Timer
2 programmable clock output function.
T2OE: Timer 2 clock output enable bit
0: Disable
1: Enable
The Timer 2 clock output is enabled by setting the T2OE bit high. When the Timer 2
clock output is disabled, the T2 pin can be used as the other pin shared functions.
Unimplemented, read as “0”
117 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
Bit 7
Bit 6
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Capture Modes
Timer 2 has two capture modes, the Capture on Edge Mode, known as Capture Mode 0, and the
Capture on Write Mode, known as Capture Mode 1. The required mode is selected using the
COCAHn and COCALn bits in the CCEN register. The accompanying diagram illustrates the basic
operational blocks.
Write to CCLn(CRCL)
Capt�re Mode 1
Capt�re Mode 0
CCn
11
01
COCAHn
COCALn
I�FR bit
TL�
CRCH/CCHn
CRCL/CCLn
Note: 1. n=0~1
2. CC1 capture input by rising edge
3. CC0 capture input by rising or falling edge selection by the I3FR bit
4. Write to CCLn is for CC1 and Write to CRCL is for CC0
Capture Modes Block Diagram
Capture On Edge Mode
To select this mode, bits COCAHn and COCALn in the CCEN register, should be set to “01”
respectively. In this mode, Modules 1 will capture the Timer 2 counter on the rising edge of an
external signal applied on the CC1 pin. Module 0 will capture the Timer 2 counter contents on
a rising or falling edge applied on the CC0 pin. The rising or falling edge trigger is controlled
by the I3FR bit in the T2CON register. In this mode, when the CCUn interrupt is enabled and a
trigger edge is detected on CCn input pin, the CCUnF interrupt flag will be set high to generate an
interrupt.
Capture On Write Mode
To select this mode, bits COCAHn and COCALn in the CCEN register, should be set to “11”
respectively. In this mode a Timer 2 Capture is generated by any write operation into the capture
register low byte. Note that the capture action occurs right after the write operation and the value
written to capture register is irrelevant for this function. The Timer 2 contents will be latched into
the appropriate capture registers. In this mode, no interrupt request will be generated.
Rev. 1.10
118 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
TH�
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Compare Modes
Timer 2 has two compare modes, known as Mode 0 and Mode 1. The required mode is selected
using the T2CM bit in the T2CON register. Setting counter data in the Compare modes can
implement the PWM function for various control applications. The CCUnF interrupt flag will be set
high when Timer 2 compare mode is enabled and counter value (TH2, TL2) is equal to Compare/
Capture register, CCH1 and CCL1, or Compare/Reload/Capture register, CRCH and CRCL.
In Mode 0, if the Timer 2 counter data is the same as the Compare registers, the compare output
will be set from low to high and the Timer 2 counter overflow will clear the respective output pins,
CCn, to low. The accompanying diagrams illustrate the Basic application blocks.
CCUn Interr�pt
CCHn/CRCH
CCLn/CRCL
Comparator
Compare Match
“1”
CCn
“0”
TH�
TL�
Overf�ow
Timer � overf�ow
Interr�pt
Note: CCHn&CCLn for CC1, CRCH&CRCL for CC0
Compare Mode 0 – Module 0~1
Rev. 1.10
119 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
Compare Mode 0
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Figure below illustrates the operation of compare mode 0.
Timer � Va��e
0xFFFF
Time
COCAHn�
COCALn
00
10
T�CM
o�tp�t high
o�tp�t high
o�tp�t high
o�tp�t high
CCn o�tp�t
SPx.� bit va��e
o�tp�t �ow
o�tp�t �ow
o�tp�t �ow
Note: 1. Px.y is the corresponding data bit of the I/O pin which is pin-shared with CCn.
2. SPx.y is the corresponding shadow bit of Px.y. When the Px.y is selected as CCn pin function, its data bit becomes the shadow bit.
3. The CCn pin output changes to low when timer 2 overflows.
Compare Match Mode 0 Timing Diagram – T2CM=0
Compare Mode 1
In Mode 1, the compare output can be decided by the software setting of the related I/O pins
register. When the compare match takes place, the control register value will be output to I/O pins,
CCn, and the Timer 2 counter overflow will not affect the Compare output. The accompanying
diagrams illustrate the Basic application blocks.
CCHn/CRCH
Comparator
TH�
CCUn Interr�pt
CCLn/CRCL
TL�
Compare Match
I/O
Contro�
Register
CCn
Timer � overf�ow
Interr�pt
Overf�ow
Note: CCHn&CCLn for CC1, CRCH&CRCL for CC0
Compare Mode 1 – Module0~1
Rev. 1.10
120 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
CRC or CCn
register va��e
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Figure below illustrates the operation of compare mode 1.
Timer � Va��e
0xFFFF
Time
COCAHn�
COCALn
00
10
T�CM
Px.�
SPx.�
CCn o�tp�t
No o�tp�t change
No o�tp�t change
No o�tp�t change
No o�tp�t change
Note: 1. Px.y is the corresponding data bit of the I/O pin which is pin-shared with CCn.
2. SPx.y is the corresponding shadow bit of Px.y and is used to control the CCn output
when compare match occurs. When the Px.y is selected as CCn pin function, its data bit
becomes the shadow bit.
3. There will no output change on CCn pin when timer 2 overflows.
Compare Match Mode 1 Timing Diagram – T2CM=1
Rev. 1.10
121 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
CRC or CCn
register va��e
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Reload Mode
EXF�
Co�nt Enab�e
EXEN�
Interr�pt
ET�
TH�/TL�
T�EX
Transition
Detector
Re�oad Mode 1
Re�oad Mode 0
CRCH/CRCL
Reload Mode – Module 0
Rev. 1.10
122 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
Module 0 provides a Reload Mode function. In the reload function, preset values in the CRCL and
CRCH registers are loaded into the TL2 and TH2 registers. There are two kinds of Reload modes,
Mode 0 and Mode 1, which are selected by the T2R1 and T2R0 bits in the T2CON register. In
Reload Mode 0, the Reload enable is controlled by the Timer 2 overflow which is an auto reload
action and a Timer 2 interrupt will take place. In Reload Mode 1, a falling edge at the T2EX input
pin will reload the data from CRCH/CRCL registers to TH2/TL2 registers. When the external
reload interrupt control bit, EXEN2, and the Timer 2 interrupt control bit, ET2, are both set high,
a Timer 2 external reload interrupt will be generated. The following diagram illustrates the basic
operation.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Programmable Clock Output Mode
The clock output frequency depends on the Timer 2 clock frequency and the reload value of Timer
2 capture registers (CRCH, CRCL) as shown in this equation:
Timer 2 Clock Frequency
Clock Output Frequency= 2 * (65536 − [CRCH, CRCL])
While the Timer 2 clock frequency is furtherly determined by the T2PRE0 and T2PRE1 bits. The
accompanying diagram illustrates the Timer2 Clock output basic operation block diagram.
fSYS
TH�/TL�
Presca�er
T�PRE[1:0]
TF�
/�
Interr�pt
T�I1=0
T�I0=1
P�.6/T�
T�OE
CRCH/CRCL
Timer2 Clock Output Block Diagram
If the Timer 2 Programmable Clock Output Mode is selected, it is essential for the Port 3 control
registers, P3M1 and P3M0, to setup the P3.6 pin as an output. The accompanying diagram
illustrates the Timer 2 programmable clock output timing diagram.
Timer � C�ock
Timer �
FFFE FFFF 0000
FFFE FFFF 0000
FFFE FFFF 0000
FFFE FFFF 0000
P�.6/T�
Programmable Clock Output Timing Diagram – Module 0
Rev. 1.10
123 of 147
July 31, 2015
Timer 2 with Additional 2-channel PCA
The Programmable Clock Output mode is related to Module 0. With this function, Timer 2 can
generate various clock outputs. This function is enabled by the T2OE bit in the T2CON1 register.
The output initial state is decided by the T2OI bit in the T2CON1 register. The Timer 2 enable
control or clock source is selected by the T2I1 and T2I0 bits in the T2CON register. The clock
source is further decided by the T2PRE1 and T2PRE0 bits in the TMPRE register. The data in the
TL2 and TH2 registers decides the clock duty cycle. If the counter overflows, then the CRCL and
CRCH registers will be auto-reloaded to the TL2 and TH2 registers. Besides being a regular I/
O pin, the P3.6 has two alternate functions. One function is to input the external clock for Timer/
Counter 2 and the other is to output a 50% duty cycle clock ranging from 61HZ to 4MHz when
the Timer 2 clock frequency is 16MHz. To configure the Timer/Counter 2 as a clock generator, the
T2I1 and T2I0 bits in the T2CON register must be set as 0 and 1 respectively to start the timer and
the T2OE bit in the T2CON1 register must be set as well.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
29
Analog to Digital Converter – ADC
The devices include a multi-channel 12-bit fully integrated Analog to Digital Converter or ADC.
A range of programmable features allow flexible and fast analog to digital conversion for a wide
range of input signals.
The Analog to Digital Converter contains a range of features which include:
■■ Multiplexed Multi-channel Inputs
■■ Programmable Gain Amplifier
■■ Temperature Sensor Input
■■ Internal Voltage Reference Source
■■ External Reference Voltage Input
■■ Programmable Clock Speed
■■ A/D Converter Interrupt
All functions are controlled using dedicated ADC control registers for setup and dynamic control.
The following block diagram shows the overall structure of the converter together with its relative
control bits.

A/D Converter Structure
Rev. 1.10
124 of 147
July 31, 2015
Analog to Digital Converter – ADC
A/D Overview
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
A/D Converter Register Description
A read only register pair exists to store the ADC data 12-bit value. The remaining registers are
control registers which setup the operating and control function of the A/D converter.
A/D Converter Register List
Bit
Register
Name
6
5
4
3
2
1
0
D3
D2
D1
D0
—
—
—
—
ADRL(ADRFS=1)
D7
D6
D5
D4
D3
D2
D1
D0
ADRH(ADRFS=0)
D11
D10
D9
D8
D7
D6
D5
D4
ADRH(ADRFS=1)
—
—
—
—
D11
D10
D9
D8
ADCR0
START
EOCB
ADOFF
ADRFS
ACS3
ACS2
ACS1
ACS0
ADCR1
ACS4
TSEN
—
VREFAS
VREFIS
ADCK2
ADCK1
ADCK0
ADCR2
ACE7
ACE6
ACE5
ACE4
ACE3
ACE2
ACE1
ACE0
ADPGA
—
—
—
—
—
ADGN2
ADGN1
ADGN0
A/D Converter Data Registers – ADRL, ADRH
As the devices contain an internal 12-bit A/D converter, they require two data registers to store the
converted value. These are a high byte register, known as ADRH, and a low byte register, known
as ADRL. After the conversion process takes place, these registers can be directly read by the
microcontroller to obtain the digitised conversion value. As only 12 bits of the 16-bit register space
is utilised, the format in which the data is stored is controlled by the ADRFS bit in the ADCR0
register as shown in the accompanying table. D0~D11 are the A/D conversion result data bits. Any
unused bits will be read as zero.
A/D Data Registers
ADRFS
ADRH (SFR Address: F6h)
ADRL (SFR Address: F5h)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
1
0
0
0
0
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
A/D Converter Control Registers – ADCR0, ADCR1, ADCR2, ADPGA
To control the function and operation of the A/D converter, four control registers known as
ADCR0, ADCR1, ADCR2 and ADPGA are provided. These 8-bit registers define functions such
as analog channel selection, converted data format, PGA gain, clock source as well as the start
bit and end of conversion flag. As the device contains only one actual analog to digital converter
hardware circuit, each of the individual 8 analog inputs must be routed to the converter. It is the
function of the ACS4 ~ ACS0 bits to determine which analog channel input pin, reference voltage
or internal temperature sensor is actually connected to the internal A/D converter.
The ADCR2 control register bits determine which pins on Port 1 and Port 3 are used as A/D
converter input and which pins are not used as A/D converter input. Setting the corresponding bit
high will select the A/D input function, clearing the bit to zero will select the I/O function or other
pin-shared function. When the pin is selected to be an A/D input, its original function whether it is
an I/O or other pin-shared function will be removed and any internal pull-high resistors connected
to these pins will be automatically removed.
The ADPGA register determines the gain of the Programmable Gain Amplifier which is used to
amplify the analog input signal before conversion by the A/D Converter.
Rev. 1.10
125 of 147
July 31, 2015
Analog to Digital Converter – ADC
ADRL(ADRFS=0)
7
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
ADCR0 Register
SFR Address: F1h
7
6
5
4
3
2
1
0
START
EOCB
ADOFF
ADRFS
ACS3
ACS2
ACS1
ACS0
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
1
1
0
0
0
0
0
Bit 7
START: Starts the A/D conversion
Bit 6
This bit is used to initiate an A/D conversion process. The bit is normally low but if set
high and then cleared low again, the A/D converter will initiate a conversion process.
When the bit is set high the A/D converter will be reset.
EOCB: End of A/D conversion flag
Bit 5
This read only flag is used to indicate when an A/D conversion process has completed.
When the conversion process is running the bit will be high.
ADOFF : ADC power on/off control bit
Bit 4
This bit controls the power to the A/D internal function. This bit should be cleared
to zero to enable the A/D converter. If the bit is set high then the A/D converter will
be switched off reducing the device power consumption. As the A/D converter will
consume a limited amount of power, even when not executing a conversion, this may be
an important consideration in power sensitive battery powered applications.
ADRFS: ADC Data Format Control
Bit 3 ~ 0
This bit controls the format of the 12-bit converted A/D value in the two A/D data
registers.
ACS3 ~ ACS0: Select A/D channel (when ACS4 is “0”)
0-->1-->0 : start
0-->1 : reset the A/D converter and set EOCB to “1”
0: A/D conversion ended
1: A/D conversion in progress
0: ADC power on
1: ADC power off
0: ADC Data MSB is ADRH bit 7, LSB is ADRL bit 4
1: ADC Data MSB is ADRH bit 3, LSB is ADRL bit 0
0000: AIN0
0001: AIN1
0010: AIN2
0011: AIN3
0100: AIN4
0101: AIN5
0110: AIN6
0111: AIN7
1xxx: Undefined, can not be used
These are the A/D channel select control bits. As there is only one internal hardware A/D
converter each of the eight A/D inputs must be routed to the internal converter using these bits. If
bit ACS4 in the ADCR1 register is set high then the internal temperature sensor will be routed to
the A/D Converter and these ADC input channels disconnected.
126 of 147
July 31, 2015
Analog to Digital Converter – ADC
Rev. 1.10
Bit
Name
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
ADCR1 Register
SFR Address: F2h
Bit
7
6
5
4
3
2
1
0
Name
ACS4
TSEN
—
VREFAS
VREFIS
ADCK2
ADCK1
ADCK0
R/W
R/W
R/W
—
R/W
R/W
R/W
R/W
R/W
POR
0
0
—
0
0
0
0
0
ACS4: Internal temperature sensor ADC input control
Bit 6
This bit enables the temperature sensor to the A/D converter. The TSEN bit must first
have been set to enable the temperature sensor circuit. When the ACS4 bit is set high,
the temperature sensor will be routed to the A/D converter and the other A/D input
channels disconnected.
TSEN: Internal temperature sensor control
0: Disable
1: Enable
Bit 4
This bit controls the internal temperature sensor function to the A/D converter. When
the bit is set high the temperature sensor can be used by the A/D converter.
Unimplemented, read as “0”
VREFAS: ADC reference voltage select
Bit 3
VREFIS: VREFI source select
Bit 2 ~ 0
ADCK2 ~ ADCK0: Select ADC clock source
Bit 5
Rev. 1.10
0: Disable
1: Enable
0: AV DD
1: VREFI
This bit is used to select the reference voltage for the A/D converter. If the bit is high then the A/
D converter reference voltage is provided by VREFI, whih is supplied on the external VREF pin
or the internal reference voltage, the choice being made using the VREFIS bit. If the pin is low
then the internal reference is used which is sourced from the power supply AVDD.
0: Externally supplied on VREF pin
1: Internal Voltage Reference Generator
000: f SYS
001: f SYS/2
010: f SYS/4
011: f SYS/8
100: f SYS/16
101: f SYS/32
110: f SYS/64
111: f SYS
127 of 147
July 31, 2015
Analog to Digital Converter – ADC
Bit 7
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
ADCR2 Register
SFR Address: F3h
Bit
7
6
5
4
3
2
1
0
Name
ACE7
ACE6
ACE5
ACE4
ACE3
ACE2
ACE1
ACE0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 2
ACE2: P3.5 A/D input select
Bit 1
ACE1: P3.4 A/D input select
Bit 0
ACE0: P1.2 A/D input select
Bit 6
Bit 5
Bit 4
Rev. 1.10
Analog to Digital Converter – ADC
Bit 3
ACE7: P1.4 A/D input select
0: I/O line or pin-shared function
1: A/D input, AIN7
ACE6: P1.3 A/D input select
0: I/O line or pin-shared function
1: A/D input, AIN6
ACE5: P3.1 A/D input select
0: I/O line or pin-shared function
1: A/D input, AIN5
ACE4: P3.7 A/D input select
0: I/O line or pin-shared function
1: A/D input, AIN4
ACE3: P3.6 A/D input select
Bit 7
0: I/O line or pin-shared function
1: A/D input, AIN3
0: I/O line or pin-shared function
1: A/D input, AIN2
0: I/O line or pin-shared function
1: A/D input, AIN1
0: I/O line or pin-shared function
1: A/D input, AIN0
128 of 147
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
ADPGA Register
SFR Address: F4h
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
ADGN2
ADGN1
ADGN0
R/W
—
—
—
—
—
R/W
R/W
R/W
POR
—
—
—
—
—
0
0
0
Unimplemented, read as “0”
ADGN2~ADGN0: PGA gain selection
000: PGA Bypass (PGA off)
001: PGA Bypass (PGA off)
010: Gain=1 (PGA on)
011: Gain=2
100: Gain=4
101: Gain=8
110: Gain=12
111: Gain=16
These three bits are used to select the PGA internal gain setting to allow greater A/D
Converter input voltage dynamic range.
When the Programmable Gain Amplifier is disabled by Setting ADGN2~ ADGN0 as 000 or 001,
the 12-bit A/D converter input signal will bypass the PGA. Otherwise the Programmable Gain
Amplifier is enabled and the 12-bit A/D converter input signal will go through the PGA.
A/D Operation
Controlling the power on/off function of the A/D converter circuitry is implemented using the
ADOFF bit in the ADCR0 register. This bit must be zero to power on the A/D converter. When the
ADOFF bit is cleared to zero to power on the A/D converter internal circuitry a certain delay, as
indicated in the timing diagram, must be allowed before an A/D conversion is initiated. Even if no
pins are selected for use as A/D inputs by clearing the ACE7~ACE0 bits in the ADCR2 register, if
the ADOFF bit is zero then some power will still be consumed. In power conscious applications it
is therefore recommended that the ADOFF is set high to reduce power consumption when the A/D
converter function is not being used.
The reference voltage supply to the A/D Converter can be supplied from either the A/D power
supply AV DD, internal voltage reference or from an external reference source supplied on pin
VREF. The desired selection is made using the VREFAS and VREFIS bits.
The START bit in the ADCR0 register is used to start and reset the A/D converter. When the
microcontroller sets this bit from low to high and then low again, an analog to digital conversion
cycle will be initiated. When the START bit is brought from low to high but not low again, the EOCB
bit in the ADCR0 register will be set high and the analog to digital converter will be reset. It is the
START bit that is used to control the overall start operation of the internal analog to digital converter.
The EOCB bit in the ADCR0 register is used to indicate when the analog to digital conversion
process is complete. This bit will be automatically set to “0” by the microcontroller after a
conversion cycle has ended. In addition, the corresponding A/D interrupt request flag will be set
in the interrupt control register, and if the interrupts are enabled, an appropriate internal interrupt
signal will be generated. This A/D internal interrupt signal will direct the program flow to the
associated A/D internal interrupt address for processing. If the A/D internal interrupt is disabled,
the microcontroller can be used to poll the EOCB bit in the ADCR0 register to check whether it has
been cleared as an alternative method of detecting the end of an A/D conversion cycle.
Rev. 1.10
129 of 147
July 31, 2015
Analog to Digital Converter – ADC
Bit 7~3
Bit 2~0
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
A/D Converter Clock Source
The clock source for the A/D converter, which originates from the system clock f SYS, can be chosen
to be either f SYS or a subdivided version of f SYS. The division ratio value is determined by the
ADCK2~ADCK0 bits in the ADCR1 register.
A/D Clock Period Examples
A/D Clock Period (tADCK)
ADCK2,
ADCK1,
ADCK0
=000
(fSYS)
ADCK2,
ADCK1,
ADCK0
=001
(fSYS/2)
ADCK2,
ADCK1,
ADCK0
=010
(fSYS/4)
ADCK2,
ADCK1,
ADCK0
=011
(fSYS/8)
ADCK2,
ADCK1,
ADCK0
=100
(fSYS/16)
ADCK2,
ADCK1,
ADCK0
=101
(fSYS/32)
ADCK2,
ADCK1,
ADCK0
=110
(fSYS/64)
1MHz
1μs
2μs
4μs
8μs
16μs*
32μs*
64μs*
1μs
2MHz
500ns
1μs
2μs
4μs
8μs
16μs*
32μs*
500ns
4MHz
250ns*
500ns
1μs
2μs
4μs
8μs
16μs*
250ns*
8MHz
125ns*
250ns*
500ns
1μs
2μs
4μs
8μs
125ns*
12MHz
83ns*
167ns*
333ns*
667ns
1.33μs
2.67μs
5.33μs
83ns*
16MHz
62.5ns*
125ns*
250ns*
500ns
1μs
2μs
4μs
62.5ns*
32MHz
31.25ns*
62.5ns*
125ns*
250ns*
500ns
1μs
2μs
31.25ns*
fSYS
ADCK2,
ADCK1,
ADCK0
=111
(fSYS)
A/D Input Pins
All of the A/D analog input pins are pin-shared with the I/O pins on P1 or P3 function. The
ACE7~ACE0 bits in the ADCR2 registers, determine whether the input pins are setup as A/D
converter analog inputs or other functions. If the ACE7~ACE0 bits for its corresponding pin is set
high then the pin will be setup to be an A/D converter input and the original pin functions disabled.
In this way, pins can be changed under program control to change their function between A/D
inputs and other functions. All pull-high resistors, which are setup through register programming,
will be automatically disconnected if the pins are setup as A/D inputs. Note that it is not necessary
to first setup the A/D pin as an input in the P1 or P3 port control register to enable the A/D input
as when the ACE7~ACE0 bits enable an A/D input, the status of the port control register will be
overridden.
The A/D converter has its own reference voltage pin, VREF, however the reference voltage can
also be supplied from the A/D power supply AVDD or internal voltage reference, a choice which is
made through the VREFAS and VREFIS bits in the ADCR1 register. The analog input values must
not be allowed to exceed the value of V REF.
Rev. 1.10
130 of 147
July 31, 2015
Analog to Digital Converter – ADC
Although the A/D clock source is determined by the system clock f SYS, and by bits ADCK2~ADCK0,
there are some limitations on the maximum A/D clock source speed that can be selected. As the
minimum value of permissible A/D clock period, tADCK, is from 0.5μs to 10μs, care must be taken
for different system clock frequencies. For example, if the system clock operates at a frequency of
4MHz, the ADCK2~ADCK0 bits should not be set to “000”, “110” or “111”. Doing so will give A/
D clock periods that are less than the minimum A/D clock period which may result in inaccurate
A/D conversion values. Refer to the following table for examples, where values marked with an
asterisk * show where, depending upon the device, special care must be taken, as the values may be
less than the specified minimum A/D Clock Period.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Temperature Sensor
A temperature sensor circuit is provided to measure the temperature which the designer can use
to adjust some measured parameters. The temperature sensor output voltage is proportional to the
temperature increment and can be amplified by the PGA. The accompanying diagram illustrates the
basic relationship between the measured temperature and the voltage output. However, the designer
should consider that the temperature sensor output voltage might be affected by the manufacturing
process.
Analog to Digital Converter – ADC
Temperature vs Voltage Diagram
The ADC temperature sensor input channel is selected by the ACS4 bit. The TSEN bit in the
ADCR1 register controls the temperature sensor enable/disable function. When the function is
disabled, the temperature sensor defaults to an unknown state and any A/D conversion performed
on the sensor will generate undefined data.
A/D Reference Voltage Source
The A/D can obtain its reference voltage from three different sources, the AV DD power supply, an
externally supplied reference voltage supplied on pin VREF or from the internal voltage reference
generator. Two bits control which reference source is selected, these are the VREFIS and VREFAS bits.
A/D Converter Voltage Reference Select
Rev. 1.10
VREFIS
VREFAS
0
0
AVDD
0
1
Externally supplied on VREF pin
1
0
AVDD
1
1
Internal Voltage Reference Generator
131 of 147
Reference Source
July 31, 2015
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Summary of A/D Conversion Steps
The following summarises the individual steps that should be executed in order to implement an A/D
conversion process.
■■ Step 1
Select the required A/D conversion clock by correctly programming bits ADCK2~ADCK0 in the
ADCR1 register and select the converted data storage format using the ADRFS bit.
■■ Step 3
Select which channel is to be connected to the internal A/D converter by correctly programming
the ACS4~ACS0 bits which are also contained in the ADCR1 and ADCR0 register.
■■ Step 4
Select which pins are to be used as A/D inputs and configure them by correctly programming the
ACE7~ACE0 bits in the ADCR2 register.
■■ Step 5
If the interrupts are to be used, the interrupt control registers must be correctly configured to ensure the A/D converter interrupt function is active. The master interrupt control bit, EAL, and the
A/D converter interrupt bit, EADC, must both be set high to do this.
■■ Step 6
The analog to digital conversion process can now be initialised by setting the START bit in the
ADCR0 register from low to high and then low again. Note that this bit should have been originally
cleared to zero.
■■ Step 7
To check when the analog to digital conversion process is completed, the EOCB bit in the
ADCR0 register can be polled. The conversion process is complete when this bit changes from
high to low. When this occurs the A/D data registers ADRL and ADRH can be read to obtain the
conversion value. As an alternative method, if the interrupts are enabled and the stack is not full,
the program can wait for an A/D interrupt to occur.
Note: When checking for the end of the conversion process, if the method of polling the EOCB bit
in the ADCR0 register is used, the interrupt enable step above can be omitted.
Rev. 1.10
132 of 147
July 31, 2015
Analog to Digital Converter – ADC
■■ Step 2
Enable the A/D by clearing the ADOFF bit in the ADCR0 register to zero and select the PGA
gain using the ADPGA register according to the dynamic range of the analog input signal.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
A/D Conversion Timing
The accompanying diagram shows graphically the various stages involved in an analog to digital
conversion process and its associated timing. After an A/D conversion process has been initiated
by the application program, the microcontroller internal hardware will begin to carry out the
conversion, during which time the program can continue with other functions. The time taken for
the A/D conversion is 16 tADCK where tADCK is equal to the A/D clock period.

A/D Conversion Timing
Programming Considerations
During microcontroller operations where the A/D converter is not being used, the A/D internal
circuitry can be switched off to reduce power consumption, by setting bit ADOFF high in the
ADCR0 register. When this happens, the internal A/D converter circuits will not consume power
irrespective of what analog voltage is applied to their input lines. If the A/D converter input lines
are used as normal I/Os, then care must be taken as if the input voltage is not at a valid logic level,
then this may lead to some increase in power consumption.
Rev. 1.10
133 of 147
July 31, 2015
Analog to Digital Converter – ADC
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
A/D Transfer Function
As the converted data is 12-bit wide, its full-scale converted digitised value is equal to FFFH. Since
the full-scale analog input value is equal to the AVDD or V REF voltage, this gives a single bit analog
input value of AVDD or VREF divided by 4096.
1 LSB= (AVDD or VREF) / 4096
A/D input voltage=A/D digital value × (AVDD or VREF) ÷ 4096 ÷ PGA Gain
The diagram shows the ideal transfer function between the analog input value and the digitised
output value for the A/D converter. Except for the digitised zero value, the subsequent digitised
values will change at a point 0.5 LSB below where they would change without the offset, and the
last full scale digitised value will change at a point 1.5 LSB below the AVDD or VREF level.

Ideal A/D Transfer Function (PGA Gain=1)
Rev. 1.10
134 of 147
July 31, 2015
Analog to Digital Converter – ADC
The A/D Converter input voltage value can be calculated using the following equation:
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
30
Voltage Reference Generator
All devices include a bandgap circuit based internal voltage reference generator which can supply a
temperature stable reference voltage for use by the internal A/D converter.
Voltage Reference Generator Operation
Internal Voltage Reference Enable/Disable Control
ADC
Voltage Reference
Disabled
Disabled
Enabled
Enabled
The internal Voltage Reference Generator output is pin VREF and can be used as a reference
source for other circuits if loaded lightly. A suitable capacitor should be connected to this pin to
enhance voltage stability. If the internal Voltage Reference Generator is enabled then the VREF pin
will act as an output pin and must be treated accordingly. However if the internal Voltage Reference
Generator is disabled, then the VREF pin will act as an input pin to enable an externally supplied
reference voltage to be provided if required.
VDD
0M
U
1X
ADC Vo�tage
Reference
VREFI
VREF
VREFAS
VREFIS
Interna� Vo�tage
Reference Generator
Enab�e/Disab�e
Contro�
A/D
Enab�e/Disab�e
Voltage Reference Generator Block Diagram
The A/D converter reference voltage is selected by the VREFIS and VREFAS control bits. When
the VREFIS bit is set the internal voltage reference will be routed to pin VREF and can be selected
for use by the A/D converter, using the VREFAS bit.
Rev. 1.10
135 of 147
July 31, 2015
Voltage Reference Generator
The voltage reference circuit will be automatically enabled when the A/D converter is enabled. If
the A/D converter is disabled then the generator will be disabled thus conserving power.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
31
Instruction Set
Introduction
The following two tables contain notes on mnemonics used in Instruction set.
Notes on Data Addressing Modes
Symbol
Description
Rn
Working register R0~R7.
direct
One of 128 internal RAM locations or any Special Function Register.
@Ri
Indirect internal or external RAM location addressed by register R0 or R1.
#data
8-bit constant included in instruction (immediate operand).
#data 16
16-bit constant included as bytes 2 and 3 of instruction (immediate operand).
bit
One of 128 software flags located in internal RAM, or any flag of bit-addressable Special Function
Registers, including I/O pins and status word.
A
Accumulator.
Notes on Program Addressing Modes
Symbol
Description
addr16
Destination address for LCALL or LJMP, can be anywhere within the 64-Kbyte page of program
memory address space.
addr11
Destination address for ACALL or AJMP, within the same 2-Kbyte page of program memory as the
first byte of the following instruction.
rel
SJMP and all conditional jumps include an 8-bit offset byte. Its range is +127/-128 bytes relative to
the first byte of the following instruction.
The following tables show instruction hexadecimal codes, number of bytes and machine cycles that
each instruction takes to be executed. Note the number of cycles is given for no program memory
wait states.
Rev. 1.10
136 of 147
July 31, 2015
Instruction Set
All instructions are binary code compatible and perform the same functions as they do within
the industry standard 8051. The following tables give a summary of instruction cycles of the
HT85XXX microcontroller core.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Arithmetic Operations
Mnemonic
Code
Bytes Cycles
ADD A,Rn
Add register to Accumulator
0X28-0X2F
1
1
ADD A,direct
Add directly addressed data to Accumulator
0X25
2
2
ADD A,@Ri
Add indirectly addressed data to Accumulator
0X26-0X27
1
2
ADD A,#data
Add immediate data to Accumulator
0X24
2
2
ADDC A,Rn
Add register to Accumulator with carry flag
0X38-0X3F
1
1
ADDC A,direct
Add directly addressed data to Accumulator with carry flag
0X35
2
2
ADDC A,@Ri
Add indirectly addresses data to Accumulator with carry flag
0X36-0X37
1
2
ADDC A,#data
Add immediate data to Accumulator with carry flag
0X34
2
2
SUBB A,Rn
Subtract register from Accumulator with borrow
0X98-0X9F
1
1
SUBB A,direct
Subtract directly addressed data from Accumulator with borrow
0X95
2
2
SUBB A,@Ri
Subtract indirectly addressed data from Accumulator with borrow 0X96-0X97
1
2
SUBB A,#data
Subtract immediate data from Accumulator with borrow
0X94
2
2
INC A
Increment Accumulator
0X04
1
1
INC Rn
Increment register
0X08-0X0F
1
1
INC direct
Increment directly addressed location
0X05
2
3
INC @Ri
Increment indirectly addressed location
0X06-0X07
1
3
INC DPTR
Increment data pointer
0XA3
1
1
DEC A
Decrement Accumulator
0X14
1
1
DEC Rn
Decrement register
0X18-0X1F
1
1
DEC direct
Decrement directly addressed location.
0X15
2
3
DEC @Ri
Decrement indirectly addressed location
0X16-0X17
1
3
MUL AB
Multiply A and B
0XA4
1
4
DIV AB
Divide A by B
0X84
1
4
DA A
Decimal adjust Accumulator
0XD4
1
1
137 of 147
July 31, 2015
Instruction Set
Rev. 1.10
Description
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Logic Operations
Mnemonic
Code
Bytes Cycles
ANL A,Rn
AND register to Accumulator
0X58-0X5F
1
1
ANL A,direct
AND directly addressed data to Accumulator
0X55
2
2
ANL A,@Ri
AND indirectly addressed data to Accumulator
0X56-0X57
1
2
ANL A,#data
AND immediate data to Accumulator
0X54
2
2
ANL direct,A
AND Accumulator to directly addressed location
0X52
2
3
ANL direct,#data
AND immediate data to directly addressed location
0X53
3
4
ORL A,Rn
OR register to Accumulator
0X48-0X4F
1
1
ORL A,direct
OR directly addressed data to Accumulator
0X45
2
2
ORL A,@Ri
OR indirectly addressed data to Accumulator
0X46-0X47
1
2
ORL A,#data
OR immediate data to Accumulator
0X44
2
2
ORL direct,A
OR Accumulator to directly addressed location
0X42
2
3
ORL direct,#data
OR immediate data to directly addressed location
0X43
3
4
XRL A,Rn
Exclusive OR register to Accumulator
0X68-0X6F
1
1
XRL A,direct
Exclusive OR directly addressed data to Accumulator
0X65
2
2
XRL A,@Ri
Exclusive OR indirectly addressed data to Accumulator
0X66-0X67
1
2
XRL A,#data
Exclusive OR immediate data to Accumulator
0X64
2
2
XRL direct,A
Exclusive OR Accumulator to directly addressed location
0X62
2
3
XRL direct,#data
Exclusive OR immediate data to directly addressed location 0X63
3
4
CLR A
Clear Accumulator
0XE4
1
1
CPL A
Complement Accumulator
0XF4
1
1
RL A
Rotate Accumulator left
0X23
1
1
RLC A
Rotate Accumulator left through carry
0X33
1
1
RR A
Rotate Accumulator right
0X03
1
1
RRC A
Rotate Accumulator right through carry
0X13
1
1
SWAP A
Swap nibbles within the Accumulator
0XC4
1
1
138 of 147
July 31, 2015
Instruction Set
Rev. 1.10
Description
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Data transfer Operations
Mnemonic
Description
Bytes Cycles
Move register to Accumulator
0XE8-0XEF
1
1
MOV A,direct
Move directly addressed data to Accumulator
0XE5
2
2
MOV A,@Ri
Move indirectly addressed data to Accumulator
0XE6-0XE7
1
2
MOV A,#data
Move immediate data to Accumulator
0X74
2
2
MOV Rn,A
Move Accumulator to register
0XF8-0XFF
1
1
MOV Rn,direct
Move directly addressed data to register
0XA8-0XAF
2
2
MOV Rn,#data
Move immediate data to register
0X78-0X7F
2
2
MOV direct,A
Move Accumulator to direct byte
0XF5
2
2
MOV direct,Rn
Move register to direct byte
0X88-0X8F
2
2
0X85
3
3
MOV direct,@Ri
Move indirectly addressed data to directly addressed location 0X86-0X87
2
2
MOV direct,#data
Move immediate data to directly addressed location
0X75
3
3
MOV @Ri,A
Move Accumulator to indirectly addressed location
0XF6-0XF7
1
1
MOV @Ri,direct
Move directly addressed data to indirectly addressed location 0XA6-0XA7
2
2
MOV @Ri,#data
Move immediate data to indirectly addressed location
0X76-0X77
2
2
MOV DPTR,#data16 Load data pointer with a 16-bit immediate
0X90
3
3
MOVC A,@A+DPTR Load Accumulator with a code byte relative to DPTR
0X93
1
4
MOVC A,@A+PC
Load Accumulator with a code byte relative to PC
0X83
1
4
MOVX A,@Ri
Move external RAM (8-bit addr.) to Accumulator
0XE2-0XE3
1
3
MOVX A,@DPTR
Move external RAM (16-bit addr.) to Accumulator
0XE0
1
3
MOVX @Ri,A
Move Accumulator to external RAM (8-bit addr.)
0XF2-0XF3
1
3
MOVX @DPTR,A
Move Accumulator to external RAM (16-bit addr.)
0XF0
1
3
PUSH direct
Push directly addressed data onto stack
0XC0
2
2
POP direct
Pop directly addressed location from stack
0XD0
2
3
XCH A,Rn
Exchange register with Accumulator
0XC8-0XCF
1
1
XCH A,direct
Exchange directly addressed location with Accumulator
0XC5
2
3
XCH A,@Ri
Exchange indirect RAM with Accumulator
0XC6-0XC7
1
2
XCHD A,@Ri
Exchange low-order nibbles of indirect and Accumulator
0XD6-0XD7
1
2
139 of 147
July 31, 2015
Instruction Set
MOV A,Rn
MOV direct1,direct2 Move directly addressed data to directly addressed location
Rev. 1.10
Code
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Program Branches
Mnemonic
Description
Code
Bytes Cycles
Absolute subroutine call
xxx10001b
2
2(*2)/3
LCALL addr16
Long subroutine call
0X12
3
3(*2)/4
RET
Return from subroutine
0X22
1
5
RETI
Return from interrupt
0X32
1
5
AJMP addr11
Absolute jump
xxx00001
2
2(*2)/3
LJMP addr16
Long jump
0X02
3
3(*2)/4
SJMP rel
Short jump (relative addr.)
0X80
2
3(*2)/4
JMP @A+DPTR
Jump indirect relative to the DPTR
0X73
1
3
JZ rel
Jump if Accumulator is zero
0X60
2
3/4(*1)
JNZ rel
Jump if Accumulator is not zero
0X70
2
3/4(*1)
JC rel
Jump if carry flag is set
0X40
2
3/4(*1)
JNC rel
Jump if carry flag is not set
0X50
2
3/4(*1)
JB bit, rel
Jump if directly addressed bit is set
0X20
3
4/5(*1)
JNB bit, rel
Jump if directly addressed bit is not set
0X30
3
4/5(*1)
JBC bit, direct rel
Jump if directly addressed bit is set and clear bit
0X10
3
4/5(*1)
CJNE A, direct rel
Compare directly addressed data to Accumulator and jump
if not equal
0XB5
3
4/5(*1)
CJNE A, #data rel
Compare immediate data to Accumulator and jump if not
equal
0XB4
3
4/5(*1)
CJNE Rn, #data rel
Compare immediate data to register and jump if not equal
0XB8-0XBF
3
4/5(*1)
CJNE @Ri, #data rel Compare immediate to indirect and jump if not equal
0XB6-0XB7
3
5/6(*1)
DJNZ Rn, rel
Decrement register and jump if not zero
0XD8-0XDF
2
3/4(*1)
DJNZ direct, rel
Decrement directly addressed location and jump if not zero
0XD5
3
4/5(*1)
NOP
No operation
0X00
1
1
Note: (*1) If the condition is true, the machine cycle will add 1.
(*2) If program execute ACALL/LCALL/AJMP/LJMP/SJMP and jump to the next address, the
machine cycle will decrease 1.
Rev. 1.10
140 of 147
July 31, 2015
Instruction Set
ACALL addr11
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Boolean Manipulation
Mnemonic
Description
Code
Bytes Cycles
Clear carry flag
0XC3
1
1
CLR bit
Clear directly addressed bit
0XC2
2
3
SETB C
Set carry flag
0XD3
1
1
SETB bit
Set directly addressed bit
0XD2
2
3
CPL C
Complement carry flag
0XB3
1
1
CPL bit
Complement directly addressed bit
0XB2
2
3
ANL C, bit
AND directly addressed bit to carry flag
0X82
2
2
ANL C,/bit
AND complement of directly addressed bit to carry
0XB0
2
2
ORL C, bit
OR directly addressed bit to carry flag
0X72
2
2
ORL C,/bit
OR complement of directly addressed bit to carry
0XA0
2
2
MOV C, bit
Move directly addressed bit to carry flag
0XA2
2
2
MOV bit, C
Move carry flag to directly addressed bit
0X92
2
3
Read-Modify-Write Instruction
Instructions that read a byte from SFR or internal RAM, modify it and rewrite it back, are called
“Read-Modify-Write” instructions. When the destination is an I/O port (P0-P3), or a Port bit, these
instructions read the output latch rather than the pin. Below table is RMW instruction set.
Mnemonic
ANL direct, A
Description
AND accumulator to direct
Code
Bytes Cycles
0x52
2
3
ANL direct, #data AND immediate data to direct
0x53
3
4
ORL direct, A
0x42
2
3
ORL direct, #data OR immediate data to direct
0x43
3
4
XRL direct, A
0x62
2
3
XRL direct, #data Exclusive OR immediate data to direct
0x63
3
4
JBC bit, rel
Jump if bit is set and clear bit
0x10
3
4/5(*)
CPL bit
Complement bit
0xB2
2
3
INC direct
Increment direct
0x05
2
3
INC @Ri
Increment indirect
0x06-0x07
1
3
DEC direct
Decrement direct
0x15
2
3
DEC @Ri
Decrement indirect
0x16-0x17
1
3
DJNZ direct, rel
Decrement and jump if not zero
0xD5
3
4/5(*)
MOV bit, C
Move carry flag and direct bit
0x92
2
3
CLR bit
Clear bit
0xC2
2
3
SETB bit
Set bit
0xD2
2
3
OR accumulator to direct
Exclusive OR accumulator to direct
Note: (*) If the condition is true, the machine cycle will add 1.
Rev. 1.10
141 of 147
July 31, 2015
Instruction Set
CLR C
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
32
Package Information
Note that the package information provided here is for consultation purposes only. As this
information may be updated at regular intervals users are reminded to consult the Holtek website
for the latest version of the package information.
• Further Package Information (include Outline Dimensions, Product Tape and Reel Speci ications)
• Packing Meterials Information
• Carton information
Rev. 1.10
142 of 147
July 31, 2015
Package Information
Additional supplementary information with regard to packaging is listed below. Click on the
relevant section to be transferred to the relevant website page.
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
20-pin SOP (300mil) Outline Dimensions
Symbol
A
Dimensions in inch
Min.
Nom.
Max.
—
0.406 BSC
—
B
—
0.406 BSC
—
C
0.012
—
0.020
C’
—
0.504 BSC
—
D
—
—
0.104
E
—
0.050 BSC
—
F
0.004
—
0.012
G
0.016
—
0.050
H
0.008
—
0.013
α
0°
—
8°
Symbol
Rev. 1.10
Dimensions in mm
Min.
Nom.
Max.
A
—
10.30 BSC
—
B
—
7.5 BSC
—
C
—
7.5 BSC
—
C’
—
12.8 BSC
—
D
—
12.8 BSC
—
E
—
1.27 BSC
—
F
0.10
—
0.30
G
0.40
—
1.27
H
0.40
—
1.27
α
0°
—
8°
143 of 147
July 31, 2015
Package Information
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
20-pin SSOP (150mil) Outline Dimensions
Symbol
Dimensions in inch
Min.
Nom.
Max.
A
—
0.236 BSC
—
B
—
0.155 BSC
—
C
0.008
—
0.012
C’
—
0.341 BSC
—
D
—
—
0.069
E
—
0.025 BSC
—
F
0.004
—
0.0098
G
0.016
—
0.05
H
0.004
—
0.01
α
0°
―
8°
Symbol
A
Rev. 1.10
Dimensions in mm
Min.
Nom.
Max.
—
6 BSC
—
B
—
3.9 BSC
—
C
0.20
—
0.30
C‘
—
8.66 BSC
—
D
—
—
1.75
E
—
0.635 BSC
—
F
0.10
—
0.25
G
0.41
—
1.27
H
0.10
—
0.25
α
0°
―
8°
144 of 147
July 31, 2015
Package Information
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
24-pin SOP (300mil) Outline Dimensions
Symbol
Dimensions in inch
Min.
Nom.
Max.
A
—
0.406 BSC
—
B
—
0.295 BSC
—
0.020
C
0.012
—
C’
—
0.606 BSC
—
D
—
—
0.104
E
—
0.050 BSC
—
F
0.004
—
0.012
G
0.016
—
0.050
H
0.008
—
0.013
α
0°
—
8°
Symbol
Rev. 1.10
Dimensions in mm
Min.
Nom.
Max.
A
—
10.30 BSC
—
B
—
7.5 BSC
—
0.51
C
0.31
—
C’
—
15.4 BSC
—
D
—
—
2.65
E
—
1.27 BSC
—
F
0.10
—
0.30
G
0.40
—
1.27
H
0.20
—
0.33
α
0°
—
8°
145 of 147
July 31, 2015
Package Information
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
24-pin SSOP (150mil) Outline Dimensions
Symbol
Dimensions in inch
Min.
Nom.
Max.
A
—
0.236 BSC
—
B
—
0.154 BSC
—
C
0.008
—
0.012
C’
—
0.341 BSC
—
D
—
—
0.069
E
—
0.025 BSC
—
F
0.004
—
0.010
G
0.016
—
0.050
H
0.004
—
0.010
α
0°
—
8°
Symbol
Rev. 1.10
Dimensions in mm
Min.
Nom.
Max.
A
—
6.0 BSC
—
B
—
3.9 BSC
—
C
0.20
—
0.30
C’
0.20
—
0.30
D
—
—
1.75
E
—
0.635 BSC
—
F
0.10
—
0.25
G
0.41
—
1.27
H
0.10
—
0.25
α
0°
—
8°
146 of 147
July 31, 2015
Package Information
A/D Flash 8051 Core Low Pin Count MCU
HT85F2230/HT85F2240
Package Information
Copyright© 2015 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time
of publication. However, Holtek assumes no responsibility arising from the use of
the specifications described. The applications mentioned herein are used solely for
the purpose of illustration and Holtek makes no warranty or representation that such
applications will be suitable without further modification, nor recommends the use of
its products for application that may present a risk to human life due to malfunction or
otherwise. Holtek's products are not authorized for use as critical components in life
support devices or systems. Holtek reserves the right to alter its products without prior
notification. For the most up-to-date information, please visit our web site at http://www.
holtek.com.tw.
Rev. 1.10
147 of 147
July 31, 2015

Open as PDF

Similar pages