FSB50825A Motion SPM® 5 Series Features Related Source • UL Certified No. E209204 (UL1557) • RD-FSB50450A - Reference Design for Motion SPM 5 Series Ver.2 • 250 V RDS(on) = 0.45 Max FRFET MOSFET 3Phase Inverter with Gate Drivers and Protection • AN-9082 - Motion SPM5 Series Thermal Performance by Contact Pressure • Built-in Bootstrap Diodes Simplify PCB Layout • AN-9080 - User’s Guide for Motion SPM 5 Series V2 • Separate Open-Source Pins from Low-Side MOSFETs for Three-Phase Current-Sensing General Description • Active-HIGH Interface, Works with 3.3 / 5 V Logic, Schmitt-trigger Input The FSB50825A is an advanced Motion SPM® 5 module providing a fully-featured, high-performance inverter output stage for AC Induction, BLDC and PMSM motors. These modules integrate optimized gate drive of the built-in MOSFETs(FRFET® technology) to minimize EMI and losses, while also providing multiple on-module protection features including under-voltage lockouts and thermal monitoring. The built-in high-speed HVIC requires only a single supply voltage and translates the incoming logic-level gate inputs to the high-voltage, high-current drive signals required to properly drive the module's internal MOSFETs. Separate open-source MOSFET terminals are available for each phase to support the widest variety of control algorithms. • Optimized for Low Electromagnetic Interference • HVIC Temperature-Sensing Built-in for Temperature Monitoring • HVIC for Gate Driving and Under-Voltage Protection • Isolation Rating: 1500 Vrms / 1 min. • RoHS Compliant Applications • 3-Phase Inverter Driver for Small Power AC Motor Drives Package Marking & Ordering Information Device Marking Device Package Reel Size Packing Type Quantity FSB50825A FSB50825A SPM5P-023 - Rail 15 ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 1 www.fairchildsemi.com FSB50825A Motion SPM® 5 Series April 2015 Inverter Part (each MOSFET unless otherwise specified.) Symbol Parameter Conditions Rating Unit VDSS Drain-Source Voltage of Each MOSFET 250 V *ID 25 Each MOSFET Drain Current, Continuous TC = 25°C 3.6 A *ID 80 Each MOSFET Drain Current, Continuous TC = 80°C 2.7 A *IDP Each MOSFET Drain Current, Peak TC = 25°C, PW < 100 s 9.0 A *IDRMS Each MOSFET Drain Current, Rms TC = 80°C, FPWM < 20 kHz 1.9 Arms Maximum Power Dissipation TC = 25°C, For Each MOSFET 14.2 W Rating Unit 20 V *PD Control Part (each HVIC unless otherwise specified.) Symbol Parameter Conditions VCC Control Supply Voltage Applied Between VCC and COM VBS High-side Bias Voltage Applied Between VB and VS VIN Input Signal Voltage Applied Between IN and COM 20 V -0.3 ~ VCC + 0.3 V Rating Unit 250 V Bootstrap Diode Part (each bootstrap diode unless otherwise specified.) Symbol VRRMB Parameter Conditions Maximum Repetitive Reverse Voltage * IFB Forward Current TC = 25°C 0.5 A * IFPB Forward Current (Peak) TC = 25°C, Under 1ms Pulse Width 1.5 A Conditions Rating Unit Each MOSFET under Inverter Operating Condition (1st Note 1) 8.8 °C/W Conditions Rating Unit Thermal Resistance Symbol RJC Parameter Junction to Case Thermal Resistance Total System Symbol TJ Parameter Operating Junction Temperature -40 ~ 150 °C TSTG Storage Temperature -40 ~ 125 °C VISO Isolation Voltage 1500 Vrms 60 Hz, Sinusoidal, 1 Minute, Connect Pins to Heat Sink Plate 1st Notes: 1. For the measurement point of case temperature TC, please refer to Figure 4. 2. Marking “ * “ is calculation value or design factor. ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 2 www.fairchildsemi.com FSB50825A Motion SPM® 5 Series Absolute Maximum Ratings FSB50825A Motion SPM® 5 Series Pin descriptions Pin Number Pin Name Pin Description 1 COM IC Common Supply Ground Bias Voltage for U-Phase High-Side MOSFET Driving 2 VB(U) 3 VCC(U) Bias Voltage for U-Phase IC and Low-Side MOSFET Driving 4 IN(UH) Signal Input for U-Phase High-Side 5 IN(UL) Signal Input for U-Phase Low-Side 6 N.C No Connection 7 VB(V) Bias Voltage for V-Phase High Side MOSFET Driving 8 VCC(V) Bias Voltage for V-Phase IC and Low Side MOSFET Driving 9 IN(VH) Signal Input for V-Phase High-Side 10 IN(VL) Signal Input for V-Phase Low-Side 11 VTS Output for HVIC Temperature Sensing Bias Voltage for W-Phase High-Side MOSFET Driving 12 VB(W) 13 VCC(W) Bias Voltage for W-Phase IC and Low-Side MOSFET Driving 14 IN(WH) Signal Input for W-Phase High-Side 15 IN(WL) Signal Input for W-Phase Low-Side 16 N.C 17 P 18 U, VS(U) 19 NU Negative DC-Link Input for U-Phase 20 NV Negative DC-Link Input for V-Phase 21 V, VS(V) No Connection Positive DC-Link Input Output for U-Phase & Bias Voltage Ground for High-Side MOSFET Driving Output for V-Phase & Bias Voltage Ground for High-Side MOSFET Driving Negative DC-Link Input for W-Phase 22 NW 23 W, VS(W) Output for W Phase & Bias Voltage Ground for High-Side MOSFET Driving (1) COM (17) P (2) VB(U) (3) V CC(U) VCC VB (4) IN (UH) HIN HO (5) IN (UL) LIN VS COM LO (18) U, V S(U) (6) N.C (19) N U (7) VB(V) (8) V CC(V) VCC VB (9) IN (VH) HIN HO LIN VS COM LO (10) IN (VL) (11) V TS (20) N V (21) V, V S(V) V TS (12) V B(W) (13) V CC(W) VCC VB (14) IN (WH) HIN HO (15) IN (WL) LIN VS COM LO (22) N W (23) W, V S(W) (16) N.C Figure 1. Pin Configuration and Internal Block Diagram (Bottom View) 1st Notes: 3. Source terminal of each low-side MOSFET is not connected to supply ground or bias voltage ground inside Motion SPM® 5 product. External connections should be made as indicated in Figure 3. ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 3 www.fairchildsemi.com Inverter Part (each MOSFET unless otherwise specified.) Symbol Parameter Conditions BVDSS Drain - Source Breakdown Voltage VIN = 0 V, ID = 1 mA (2nd Note 1) IDSS Zero Gate Voltage Drain Current RDS(on) VSD - - V VIN = 0 V, VDS = 250 V - - 1 mA Static Drain - Source Turn-On Resistance VCC = VBS = 15 V, VIN = 5 V, ID = 2.0 A - 0.33 0.45 Drain - Source Diode Forward Voltage VCC = VBS = 15V, VIN = 0 V, ID = -2.0 A - - 1.2 V - 950 - ns - 520 - ns Switching Times VPN = 150 V, VCC = VBS = 15 V, ID = 2.0 A VIN = 0 V 5 V, Inductive Load L = 3 mH High- and Low-Side MOSFET Switching (2nd Note 2) - 150 - ns - 100 - J - 10 - J tOFF EON EOFF RBSOA Unit 250 tON trr Min Typ Max V = 200 V, VCC = VBS = 15 V, ID = IDP, VDS = BVDSS, Reverse Bias Safe Oper- PN TJ = 150°C ating Area High- and Low-Side MOSFET Switching (2nd Note 3) Full Square Control Part (each HVIC unless otherwise specified.) Symbol Parameter Conditions Min Typ Max Unit IQCC Quiescent VCC Current VCC = 15 V, VIN = 0 V Applied Between VCC and COM - - 200 A IQBS Quiescent VBS Current VBS = 15 V, VIN = 0 V Applied Between VB(U) - U, VB(V) - V, VB(W) - W - - 100 A UVCCD UVCCR UVBSD UVBSR Low-Side Under-Voltage Protection (Figure 8) VCC Under-Voltage Protection Detection Level 7.4 8.0 9.4 V VCC Under-Voltage Protection Reset Level 8.0 8.9 9.8 V High-Side Under-Voltage Protection (Figure 9) VBS Under-Voltage Protection Detection Level 7.4 8.0 9.4 V VBS Under-Voltage Protection Reset Level 8.0 8.9 9.8 V 600 790 980 mV - - 2.9 V 0.8 - - V VTS HVIC Temperature Sensing Voltage Output VCC = 15 V, THVIC = 25°C (2nd Note 4) VIH ON Threshold Voltage Logic HIGH Level VIL OFF Threshold Voltage Logic LOW Level Applied between IN and COM Bootstrap Diode Part (each bootstrap diode unless otherwise specified.) Symbol Parameter Conditions Min Typ Max Unit VFB Forward Voltage IF = 0.1 A, TC = 25°C (2nd Note 5) - 2.5 - V trrB Reverse Recovery Time IF = 0.1 A, TC = 25°C - 80 - ns 2nd Notes: 1. BVDSS is the absolute maximum voltage rating between drain and source terminal of each MOSFET inside Motion SPM® 5 product. VPN should be sufficiently less than this value considering the effect of the stray inductance so that VPN should not exceed BVDSS in any case. 2. tON and tOFF include the propagation delay of the internal drive IC. Listed values are measured at the laboratory test condition, and they can be different according to the field applications due to the effect of different printed circuit boards and wirings. Please see Figure 6 for the switching time definition with the switching test circuit of Figure 7. 3. The peak current and voltage of each MOSFET during the switching operation should be included in the Safe Operating Area (SOA). Please see Figure 7 for the RBSOA test circuit that is same as the switching test circuit. 4. Vts is only for sensing-temperature of module and cannot shutdown MOSFETs automatically. 5. Built-in bootstrap diode includes around 15 Ω resistance characteristic. Please refer to Figure 2. ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 4 www.fairchildsemi.com FSB50825A Motion SPM® 5 Series Electrical Characteristics (TJ = 25°C, VCC = VBS = 15 V unless otherwise specified.) Symbol Parameter Conditions Min. Typ. Max. Unit VPN Supply Voltage Applied Between P and N - 150 200 V VCC Control Supply Voltage Applied Between VCC and COM 13.5 15.0 16.5 V VBS High-Side Bias Voltage Applied Between VB and VS 13.5 15.0 16.5 V 3.0 - VCC V 0 - 0.6 V 1.0 - - s - 15 - kHz VIN(ON) Input ON Threshold Voltage VIN(OFF) Input OFF Threshold Voltage Applied Between IN and COM tdead Blanking Time for Preventing VCC = VBS = 13.5 ~ 16.5 V, TJ 150°C Arm-Short fPWM PWM Switching Frequency TJ 150°C Built-in Bootstrap Diode VF-IF Characteristic 1.0 0.9 0.8 0.7 IF [A] 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 6 7 8 VF [V] 9 10 11 12 13 14 15 Tc=25°C Figure 2. Built-in Bootstrap Diode Characteristics (Typical) ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 5 www.fairchildsemi.com FSB50825A Motion SPM® 5 Series Recommended Operating Condition C1 +15 V * Example Circuit : V phase VDC P MCU R5 C5 VCC VB HIN HO LIN VS COM LO V 10 F C2 C4 LIN Output Note 0 0 Z Both FRFET Off 0 1 0 Low side FRFET On C3 1 0 VDC High side FRFET On 1 1 Forbidden Shoot through Open Open Z Same as (0,0) R3 N VTS HIN Inverter Output ® One Leg Diagram of Motion SPM 5 Product * Example of Bootstrap Paramters : C1 = C2 = 1 F Ceramic Capacitor Figure 3. Recommended MCU Interface and Bootstrap Circuit with Parameters 3rd Notes: 1. Parameters for bootstrap circuit elements are dependent on PWM algorithm. For 15 kHz of switching frequency, typical example of parameters is shown above. 2. RC-coupling (R5 and C5) and C4 at each input of Motion SPM 5 product and MCU (Indicated as Dotted Lines) may be used to prevent improper signal due to surge-noise. 3. Bold lines should be short and thick in PCB pattern to have small stray inductance of circuit, which results in the reduction of surge-voltage. Bypass capacitors such as C1, C2 and C3 should have good high-frequency characteristics to absorb high-frequency ripple-current. Figure 4. Case Temperature Measurement 3rd Notes: 4. Attach the thermocouple on top of the heat-sink of SPM 5 package (between SPM 5 package and heatsink if applied) to get the correct temperature measurement. 3.5 3.0 VTS [V] 2.5 2.0 1.5 1.0 0.5 20 40 60 80 100 120 140 160 o THVIC [ C] Figure 5. Temperature Profile of V TS (Typical) ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 6 www.fairchildsemi.com FSB50825A Motion SPM® 5 Series These values depend on PWM control algorithm FSB50825A Motion SPM® 5 Series VIN VIN Irr VDS 120% of ID 100% of ID ID 10% of ID ID VDS tON trr tOFF (a) Turn-on (b) Turn-off Figure 6. Switching Time Definitions C BS VCC ID VCC VB HIN HO LIN VS COM LO L VDC + V DS - VTS ® One Leg Diagram of Motion SPM 5 Product Figure 7. Switching and RBSOA (Single-pulse) Test Circuit (Low-side) Input Signal UV Protection Status Low-side Supply, VCC RESET DETECTION RESET UVCCR UVCCD MOSFET Current Figure 8. Under-Voltage Protection (Low-Side) Input Signal UV Protection Status High-side Supply, VBS RESET DETECTION RESET UVBSR UVBSD MOSFET Current Figure 9. Under-Voltage Protection (High-Side) ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 7 www.fairchildsemi.com (2 ) VB(U) (3 ) VCC(U) R5 (4 ) IN(UH) (5 ) IN(UL) C5 C2 (6 ) N.C (17) P VCC VB HIN HO LIN VS COM LO (18) U , VS(U) C3 (19) NU (7 ) VB(V) (8 ) VCC(V) (9 ) IN(VH) Micom (10) IN(VL) (11) VTS VDC VCC VB HIN HO LIN VS COM LO (20) NV (21) V , VS(V) M VTS (12) VB(W) (13) VCC(W) (14) IN(WH) (15) IN(WL) (16) N.C VCC VB HIN HO LIN VS COM LO (22) NW (23) W , VS(W) C4 For current-sensing and protection 15 V Supply R4 C6 R3 Figure 10. Example of Application Circuit 4th Notes: 1. About pin position, refer to Figure 1. 2. RC-coupling (R5 and C5, R4 and C6) and C4 at each input of Motion SPM® 5 product and MCU are useful to prevent improper input signal caused by surge-noise. 3. The voltage-drop across R3 affects the low-side switching performance and the bootstrap characteristics since it is placed between COM and the source terminal of the lowside MOSFET. For this reason, the voltage-drop across R3 should be less than 1 V in the steady-state. 4. Ground-wires and output terminals, should be thick and short in order to avoid surge-voltage and malfunction of HVIC. 5. All the filter capacitors should be connected close to Motion SPM 5 product, and they should have good characteristics for rejecting high-frequency ripple current. ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 8 www.fairchildsemi.com FSB50825A Motion SPM® 5 Series C1 (1 ) COM FSB50825A Motion SPM® 5 Series Detailed Package Outline Drawings Dimension unit : [mm] Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or data on the drawing and contact a FairchildSemiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide therm and conditions, specifically the the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/dwg/MO/MOD23DG.pdf ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 9 www.fairchildsemi.com FSB50825A Motion SPM® 5 Series ©2012 Fairchild Semiconductor Corporation FSB50825A Rev. 1.1 10 www.fairchildsemi.com