Kingbright APA3010QBC-D-GX 3.0mmx1.0 mm right angle smd chip led lamp Datasheet

3.0mmx1.0 mm RIGHT ANGLE SMD
CHIP LED LAMP
ATTENTION
Part Number: APA3010QBC/D-GX
Blue
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z 3.0mmx2.0mmx1.0mm right angle SMD LED, 1.0mm
z The Blue source color devices are made with InGaN
Light Emitting Diode.
thickness.
z Electrostatic discharge and power surge could damage
z Low power consumption.
the LEDs.
z Wide viewing angle.
z Ideal for back light and indicator.
z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs.
z Package : 2000pcs / reel.
z Moisture sensitivity level : level 3.
z Tinned pads for improved solderability.
z All devices, equipments and machineries must be
electrically grounded.
z RoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.15(0.006") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4.The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAL3672
APPROVED: Wynec
REV NO: V.8B
CHECKED: Allen Liu
DATE: AUG/20/2015
PAGE: 1 OF 5
DRAWN: M.Liu
ERP: 1203000606
Selection Guide
Part No.
Emitting Color (Material)
APA3010QBC/D-GX
Blue (InGaN)
Viewing
Angle [1]
Iv (mcd) [2]
@ 20mA
Lens Type
Min.
Typ.
2θ1/2
40
80
120°
Water Clear
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Emitting Color
Typ.
λpeak
Peak Wavelength
Blue
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
460
nm
IF=20mA
Blue
465
nm
IF=20mA
Spectral Line Half-width
Blue
25
nm
IF=20mA
C
Capacitance
Blue
100
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Blue
3.3
4
V
IF=20mA
IR
Reverse Current
Blue
50
uA
VR=5V
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Values
Units
Power dissipation
120
mW
DC Forward Current
30
mA
Peak Forward Current [1]
150
mA
Electrostatic Discharge Threshold (HBM)
250
V
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAL3672
APPROVED: Wynec
REV NO: V.8B
CHECKED: Allen Liu
DATE: AUG/20/2015
PAGE: 2 OF 5
DRAWN: M.Liu
ERP: 1203000606
Blue
SPEC NO: DSAL3672
APPROVED: Wynec
APA3010QBC/D-GX
REV NO: V.8B
CHECKED: Allen Liu
DATE: AUG/20/2015
PAGE: 3 OF 5
DRAWN: M.Liu
ERP: 1203000606
APA3010QBC/D-GX
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAL3672
APPROVED: Wynec
REV NO: V.8B
CHECKED: Allen Liu
DATE: AUG/20/2015
PAGE: 4 OF 5
DRAWN: M.Liu
ERP: 1203000606
PACKING & LABEL SPECIFICATIONS
APA3010QBC/D-GX
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAL3672
APPROVED: Wynec
REV NO: V.8B
CHECKED: Allen Liu
DATE: AUG/20/2015
PAGE: 5 OF 5
DRAWN: M.Liu
ERP: 1203000606
Similar pages