GS12E 10 ~ 12W AC-DC Single Output Wall-mounted type series Features : Universal AC input / Full range No load power consumption< 0.3W ErP step2 compliant Meet EISA 2007 (Energy Independence and Security Act) 2 pole EURO plug Class power (without earth pin) Protections: Short circuit / Overload / Over voltage / Over temperature Fully enclosed plastic case Approvals: TUV / CB / CE Pass LPS for full series 2 years warranty SPECIFICATION ORDER NO. OUTPUT GS12E05-P1I GS12E07-P1I GS12E09-P1I GS12E12-P1I GS12E15-P1I GS12E18-P1I SAFETY MODEL NO. GS12E05 GS12E07 GS12E09 GS12E12 GS12E15 GS12E18 GS12E24 DC VOLTAGE 5V 7.5V 9V 12V 15V 18V 24V RATED CURRENT 2.0A 1.6A 1.33A 1.0A 0.8A 0.67A 0.5A CURRENT RANGE 0 ~ 2.0A 0 ~ 1.6A 0 ~ 1.33A 0 ~ 1.0A 0 ~ 0.8A 0 ~ 0.67A 0 ~ 0.5A RATED POWER 10W 12W 12W 12W 12W 12.06W 12W 120mVp-p 150mVp-p 180mVp-p 200mVp-p RIPPLE & NOISE (max.) Note.2 75mVp-p GS12E24-P1I 90mVp-p 90mVp-p VOLTAGE TOLERANCE Note.3 5.0% 4.0% 4.0% 3.0% 3.0% 3.0% 3.0% LINE REGULATION Note.4 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% 1.0% LOAD REGULATION Note.5 5.0% 4.0% 4.0% 3.0% 3.0% 2.0% 2.0% 500ms, 20ms, 10ms/115VAC at full load SETUP, RISE, HOLD UP TIME 500ms, 20ms, 30ms/230VAC 90 ~ 264VAC 135 ~ 370VDC VOLTAGE RANGE FREQUENCY RANGE INPUT 47 ~ 63Hz EFFICIENCY (Typ.) 76% 78.5% AC CURRENT 0.31A / 115VAC 0.16A / 230VAC INRUSH CURRENT (max.) COLD START 25A / 115VAC LEAKAGE CURRENT (max.) 0.25mA / 240VAC >105% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed OVERLOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE Note.6 78.5% 78.5% 80% 80% 80.5% 45A / 230VAC 115% ~ 135% Protection type : Clamp by zener diode U1 Tj 140 typically (U1) Detect on main control IC Protection type : Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. 0 ~ +50 WORKING HUMIDITY 20% ~ 90% RH non-condensing (Refer to "Derating Curve") ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85 , 10 ~ 95% RH TEMP. COEFFICIENT 0.03% / (0 ~ 40 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes VIBRATION SAFETY STANDARDS TUV EN60950 -1 approved WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC EMC EMISSION EMC IMMUNITY MTBF I/P-O/P:3KVAC I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55022, EN61204-3, EN61000-3-2,3, FCC part15 class B Compliance to EN61000-4-2,3,4,5,6,8,11, EN61204-3, light industry level, criteria A 1414.6Khrs min. MIL-HDBK-217F (25 ) OTHERS DIMENSION PACKING 65*47*26.5mm (L*W*H) 0.15Kg ; 100pcs / 16Kg / CARTON PLUG Standard type P1I: 2.1 CABLE Standard type UL1185 6ft (4FT only for 5V output) for stock ; Other type available by customer requested CONNECTOR NOTE * 5.5 * 9.5mm turning fork type, center positive for stock ; Other type available by customer requested 1.All parameters are specified at 230VAC input, rated load, 25 70% RH ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Tolerance: includes set up tolerance, line regulation, load regulation. 4.Line regulation is measured from low line to high line at rated load. 5.Load regulation is measured from 10% to 100% rated load. 6.The over temperature protection (OTP) is the built-in function of the control IC (U1). The activating level described above is based on the specification provided by the IC manufacturer. File Name:GS12E-SPEC 2011-06-14 GS12E 10 ~ 12W AC-DC Single Output Wall-mounted type Mechanical Specification series Unit:mm UL1185 16AWG 1230 50mm for 5V~9V UL1185 18AWG 1830 50mm for 12V~24V 37.2 1 26.5 1 30 10mm 65 1 47 1 ID 2.1 x OD 5.5 C"+" 9.5 0.5mm Plug Assignment Standard plug: P1I P1I Derating Curve + 20 30 Ta ( 40 ) 50 32 300 28 250 24 200 20 150 16 100 12 50 8 25 50 70 90 110 120 140 160 180 200 220 240 OUTPUT RIPPLE (mVp-p) OUTPUT VOLTAGE (V) LOAD (%) 70 10 OUTPUT Static Characteristics(24V) 100 0 P/N CENTER 264 INPUT VOLTAGE(VAC)60Hz File Name:GS12E-SPEC 2011-06-14