TI BQ2112BKT Nicd or nimh gas gauge module with slow-charge control Datasheet

bq2112
NiCd or NiMH Gas Gauge Module
with Slow-Charge Control
Features
ä
Complete bq2012 Gas Gauge solution for NiCd or
NiMH battery packs
ä
Output for slow-charge control of battery pack
ä
Battery information available over a single-wire
bidirectional serial port
ä
Battery state-of-charge monitoring for 4- to 12-cell
series applications
ä
On-board regulator allows direct connection to the
battery
ä
“L” version includes push-button activated LEDs to
display state-of-charge information
ä
Nominal capacity and cell chemistry pre-configured
ä
Compact size for battery pack integration
A module development kit is also available for the
bq2112. The bq2112B-KT or bq2112LB-KT includes one
configured module and the following:
General Description
1)
An interface board that allows connection to the serial port of an AT-compatible computer.
The bq2112 Gas Gauge Module provides a complete and
compact solution for capacity monitoring of NiCd and
NiMH battery packs. Designed for battery pack integration, the bq2112 incorporates a bq2012 Gas Gauge IC, a
current sense resistor, and all other components necessary to accurately monitor and display the capacity of 3
to 12 series cells. The bq2112L includes six surfacemounted LEDs to display remaining capacity in 20% increments of the learned capacity (relative mode) or programmed capacity (absolute mode). The sixth LED is
used in absolute mode to represent an overfull condition
(charge above the programmed capacity). The LEDs are
activated with the onboard push--button switch.
2)
Menu-driven software with the bq2112 to display
charge/discharge activity and to allow user interface to the bq2012 from any standard DOS PC.
3)
Source code for the TSR.
Contacts are provided on the bq2112 for direct connection to the battery stack (BAT+, BAT-), the serial communications port (DQ), the empty indicator (EMPTY),
and the charge control output (CHG). Please refer to the
bq2012 data sheet for the specifics on the operation of
the Gas Gauge.
Pin Descriptions
Unitrode configures the bq2112 based on the information requested in Table 1. The configuration defines the
number of series cells, the nominal battery pack capacity, the self-discharge rate, and the LED display mode.
5/99 B
1
P1
DQ/Serial communication port
P2
BAT+/Battery positive/pack positive
P3
CHG/Charge control output
P4
EMPTY/Empty indicator output
P5
GND/Ground
P6
PACK-/Pack negative
P7
BAT-/Battery negative
bq2112
Battery Pack
Cells
P7
bq2112
P6
P2
PACK+
PACKLoad
Charger
FG-961
Figure 1. Module Connection Diagram
Table 1. bq2112 Module Configuration
Customer Name: ___________________________________________________________________________
Contact: _________________________________________
Phone: ______________________________
Address: _________________________________________________________________________________
_________________________________________________________________________________
Sales Contact: ____________________________________
Phone: ______________________________
Number of series battery cells (4-12)
________________________________________
Battery type (NiCd or NiMH)
________________________________________
Battery pack capacity (mAh)
________________________________________
Discharge rate into load (3.0A max.)
Min.
Charge rate (3.0A max)
________________________________________
Display mode (absolute or relative)
________________________________________
LEDs and switch (Y/N)
________________________________________
Avg.
FAE approval: _____________________________________
2
Max.
Date:________________________________
bq2112
bq2112 Schematic
Note:
Schematic shows components which may not be placed on the
board, depending upon the configuration.
3
bq2112
bq2112 Board
4
bq2112
Absolute Maximum Ratings
Symbol
Parameter
Minimum
Maximum
Unit
Conditions
VCC
Relative to VSS
-0.3
+7.0
V
bq2012
All other pins
Relative to VSS
-0.3
+7.0
V
bq2012
PSR
Continuous sense resistor power dissipation
-
3
W
Thru-hole sense resistor
-
1
W
Surface mount sense resistor
ICHG
Continuous charge/
discharge current
-
3.0
A
TOPR
Operating temperature
0
+70
°C
TSTR
Storage temperature
-40
+85
°C
Note:
Commercial
Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation
should be limited to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to conditions beyond the operational limits for extended periods of time may affect device reliability.
DC Electrical Characteristics (TA = TOPR)
Symbol
Parameter
Minimum
Typical
Maximum
Unit
NumCell
Number of series cells in battery pack
4
-
12
-
BAT+
Positive terminal of pack
GND
BAT-
Negative terminal of pack
GND 0.3
-
GND+2.0
V
ICC
Supply current at BAT+ terminal (no external loads)
-
200
300
µA
RDQ
Internal pull-down
500k
-
-
Ω1
IOL
Open-drain sink current DQ,
EMPTY, CHG
-
-
5.0
mA1
VOL
Open-drain output low,
DQ, EMPTY, CHG
-
-
0.5
V1
VIHDQ
DQ input high
2.5
-
-
V1
VILDQ
DQ input low
-
-
0.8
V1
VOS
Voltage offset
-
-
150
µV1
Note:
NumCell * 1.2V NumCell * 1.8V
1. Characterized on PCB, IC 100% tested.
5
Conditions/Notes
V
IOL < 5mA
bq2112
DC Voltage Thresholds (TA = TOPR)
Symbol
Parameter
Minimum
Typical
Maximum
Unit
0.93
0.95
0.97
V
Notes
BAT+/NumCell1
VEDVF
Final empty warning
VEDV1
First empty warning
1.03
1.05
1.07
V
BAT+/NumCell1
VMCV
Maximum single-cell voltage
2.20
2.25
2.30
V
BAT+/NumCell1
VSRO
Sense resistor range
-300
-
+2000
mV
VSR + VOS2
VSRQ
Valid charge
375
-
-
µV
VSR + VOS 2, 3
VSRD
Valid discharge
-
-
-300
µV
VSR + VOS 2, 3
Notes:
1. At SB input of bq2012.
2. At SR input of bq2012.
3. Default value; value set in DMF register.
Data Sheet Revision History
Change No.
Page No.
1
2
Updated Table 1 to include 3.0A limit
1
5
Added 3.0A maximum continuous charge/discharge current specification
Note:
Description
Change 1 = May 1999 B changes from Nov. 1997.
Ordering Information
bq2112
B —
Customer Code:
Blank = Sample or Pre-production1
KT = Evaluation system
XXX = Customer specific; assigned by Unitrode2
Package Option:
B = Board-level product
LED Option:
L = LEDs plus switch
Blank = No LEDs or switch
Device:
NiCd or NiMH Gas Gauge Module with Slow-Charge Control
Notes:
1. Requires configuration sheet (see Table 1)
2. Example production part number: bq2112LB-002
6
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated
Similar pages