3.0x2.0mm RIGHT ANGLE SMD LED Part Number: APBDA3020CGKSYKC-GX Green Super Bright Yellow Features Descriptions z 3.0mmx2.0mm SMT LED,2.8mm thickness. z The Green source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode. z Low power consumption. z Ideal for back light and indicator z The Super Bright Yellow device is made with AlGaInP (on GaAs substrate) light emitting diode chip. z Package : 2000pcs / reel. z When soldered in the sideview configuration, the maximum shear tolerance of the epoxy lens is 300g. z Moisture sensitivity level : level 3. z Tinned pads for improved solderability z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL0181 REV NO: V.6B DATE: MAR/17/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 1 OF 6 ERP: 1203012188 Selection Guide Part No. Dice Green (AlGaInP) APBDA3020CGKSYKC-GX Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Water Clear Super Bright Yellow (AlGaInP) Min. Typ. 120 280 400 700 2θ1/2 15° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. 3. Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Green Super Bright Yellow λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 574 590 nm IF=20mA Green Super Bright Yellow 570 590 nm IF=20mA Spectral Line Half-width Green Super Bright Yellow 20 20 nm IF=20mA C Capacitance Green Super Bright Yellow 15 20 pF VF=0V;f=1MHz VF [2] Forward Voltage Green Super Bright Yellow 2.1 2 2.5 2.5 V IF=20mA IR Reverse Current Green Super Bright Yellow 10 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Green Super Bright Yellow Units Power dissipation 75 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 150 175 mA Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAL0181 REV NO: V.6B DATE: MAR/17/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 2 OF 6 ERP: 1203012188 APBDA3020CGKSYKC-GX Green SPEC NO: DSAL0181 REV NO: V.6B DATE: MAR/17/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 3 OF 6 ERP: 1203012188 Super Bright Yellow SPEC NO: DSAL0181 REV NO: V.6B DATE: MAR/17/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 4 OF 6 ERP: 1203012188 APBDA3020CGKSYKC-GX Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL0181 REV NO: V.6B DATE: MAR/17/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 5 OF 6 ERP: 1203012188 PACKING & LABEL SPECIFICATIONS APBDA3020CGKSYKC-GX Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL0181 REV NO: V.6B DATE: MAR/17/2015 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng PAGE: 6 OF 6 ERP: 1203012188