Hittite HMC684LP4 Bicmos mmic mixer w/ integrated lo amplifier, 700 - 1000 mhz Datasheet

HMC684LP4 / 684LP4E
v03.0110
Mixers - SINGLE & DOUBLE BALANCED - SMT
10
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 700 - 1000 MHz
Typical Applications
Features
The HMC684LP4(E) is Ideal for:
High Input IP3: +32 dBm
• Cellular/3G & LTE/WiMAX/4G
Low Conversion Loss: 7 dB
• Basestations & Repeaters
Low LO Drive: 0 dBm
• GSM, CDMA & OFDM
Upconversion & Downconversion Applications
• Transmitters and Receivers
24 Lead 4x4mm SMT Package: 16mm2
Functional Diagram
General Description
The HMC684LP4(E) is a high dynamic range passive
MMIC mixer with integrated LO amplifier in a 4x4
SMT QFN package covering 0.7 to 1.0 GHz. Excellent
input IP3 performance of +32 dBm for down conversion is provided for 3G & 4G GSM/CDMA applications
at an LO drive of 0 dBm. With an input 1 dB compression of +25 dBm, the RF port will accept a wide
range of input signal levels. Conversion loss is 7 dB
typical. The DC to 450 MHz IF frequency response
will satisfy GSM/CDMA transmit or receive frequency
plans. The HMC684LP4(E) is pin for pin compatible
with the HMC685LP4(E) which is a 1.7 - 2.2 GHz mixer
with LO amplifier.
Electrical Specifications
TA = +25° C, IF = 100 MHz, LO = 0 dBm, Vcc1, 2, 3, = +5V, G_Bias = +3.5V*
Parameter
Min.
Frequency Range, RF
Typ.
Max.
0.7 - 1.0
Units
GHz
Frequency Range, LO
0.6 - 1.0
GHz
Frequency Range, IF
DC to 450
MHz
Conversion Loss
7
Noise Figure (SSB)
7
9
dB
dB
LO to RF Isolation
17
23
dB
LO to IF Isolation
20
30
dB
RF to IF Isolation
25
35
dB
IP3 (Input)
32
dBm
1 dB Compression (Input)
25
dBm
LO Drive Input Level (Typical)
-6 to +3
Supply Current Icc Total
85
dBm
100
mA
* Unless otherwise noted all measurements performed as downconverter with low side LO & IF = 100 MHz.
10 - 1
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC684LP4 / 684LP4E
v03.0110
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 700 - 1000 MHz
Isolation
Conversion Gain vs. Temperature
0
RF/IF
LO/RF
LO/IF
-5
-10
+25 C
+85 C
-40 C
-15
-20
0.6
0.7
0.8
-30
-40
-50
0.9
1
1.1
-60
0.6
1.2
0.7
0.8
FREQUENCY (GHz)
0.9
1
1.1
1.2
FREQUENCY (GHz)
Return Loss
Conversion Gain vs. LO Drive
0
0
-5
-5
RETURN LOSS (dB)
CONVERSION GAIN (dB)
10
-20
-10
-6 dBm
-3 dBm
0 dBm
+3 dBm
-15
-20
0.6
0.7
0.8
RF
LO
-10
-15
-20
-25
0.9
1
1.1
-30
0.4
1.2
0.5
FREQUENCY (GHz)
0.6
0.7
0.8
0.9
1
1.1
1.2
FREQUENCY (GHz)
Input P1dB vs. Temperature
IF Bandwidth (LO = 0.8 GHz)
30
0
-5
P1dB (dBm)
RESPONSE (dB)
25
-10
-15
20
-20
+25 C
+85 C
-40 C
15
IF Return Loss
Conversion Gain
-25
-30
0
0.1
0.2
0.3
FREQUENCY (GHz)
0.4
0.5
10
0.6
Mixers - SINGLE & DOUBLE BALANCED - SMT
-10
ISOLATION (dB)
CONVERSION GAIN (dB)
0
0.7
0.8
0.9
1
1.1
1.2
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10 - 2
HMC684LP4 / 684LP4E
v03.0110
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 700 - 1000 MHz
Input IP3 vs. Temperature [1]
40
30
30
IP3 (dBm)
40
20
-6 dBm
-3 dBm
0 dBm
+3 dBm
10
0
0.7
0.75
0.8
0.85
0.9
20
+25 C
+85 C
-40 C
10
0.95
0
0.7
1
0.75
+2RF -2LO Response vs. Temperature [2]
+25 C
+85 C
-40 C
+2RF-2LO RESPONSE (dBc)
+2RF-2LO RESPONSE (dBc)
0.9
0.95
1
70
65
60
55
50
45
0.7
0.8
0.9
1
1.1
60
55
50
45
40
0.6
1.2
-3 dBm
0 dBm
+3 dBm
65
0.7
0.8
0.9
1
1.1
1.2
FREQUENCY (GHz)
FREQUENCY (GHz)
+3RF -3LO Response vs. Temperature [2]
+3RF -3LO Response vs. LO Drive [2]
90
90
+3RF-3LO RESPONSE (dBc)
+25 C
+85 C
-40 C
85
80
75
70
65
60
0.6
0.85
+2RF -2LO Response vs. LO Drive [2]
70
40
0.6
0.8
FREQUENCY (GHz)
FREQUENCY (GHz)
+3RF-3LO RESPONSE (dBc)
Mixers - SINGLE & DOUBLE BALANCED - SMT
10
IP3 (dBm)
Input IP3 vs. LO Drive [1]
0.7
0.8
0.9
1
FREQUENCY (GHz)
1.1
1.2
-3 dBm
0 dBm
+3 dBm
85
80
75
70
65
60
0.6
0.7
0.8
0.9
1
1.1
1.2
FREQUENCY (GHz)
[1] Two-tone input power = +9 dBm each tone, 1 MHz spacing. [2] Reference to RF Power at 0 dBm
10 - 3
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC684LP4 / 684LP4E
v03.0110
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 700 - 1000 MHz
Upconverter Performance
Input IP3 vs. LO Drive
40
-5
30
-10
-6 dBm
-3 dBm
0 dBm
+3 dBm
-15
-20
0.6
0.7
0.8
0.9
10
20
-6 dBm
-3 dBm
0 dBm
+3 dBm
10
1
1.1
1.2
0
0.6
0.7
FREQUENCY (GHz)
0.8
0.9
1
1.1
1.2
FREQUENCY (GHz)
Absolute Maximum Ratings
MxN Spurious @ IF Port
RF / IF Input (Vcc1 - 3 = +5V)
+26 dBm
LO Drive (Vcc= +5V)
+10 dBm
Vcc1 - 3 (LO or IF)
nLO
mRF
0
1
2
3
4
5.5V
0
xx
25
16
25
31
Channel Temperature
125 °C
1
25
0
25
17
35
Continuous Pdiss (T = 85°C)
(derate 17.24 mW/°C above 85°C)
0.69W
Thermal Resistance
(channel to ground paddle)
58 °C/W
Storage Temperature
-65 to 150 °C
Operating Temperature
-40 to +85 °C
ESD Sensitivity (HBM)
Class 1A
2
52
47
50
55
58
3
82
73
92
70
77
4
112
100
112
110
98
RF Freq. = 0.9 GHz @ 0 dBm
LO Freq. = 0.8 GHz @ 0 dBm
All values in dBc below IF power level (1RF - 1LO).
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Typical Supply Current vs. Vcc
Harmonics of LO
Vcc1 - 3 (V)
Icc Total (mA)
4.75
80
LO Freq. (GHz)
1
2
3
4
5.00
85
0.5
26
45
36
43
5.25
90
0.6
24
43
35
36
Product will operate over full voltage range shown above.
nLO Spur @ RF Port
0.7
22
30
41
30
0.8
22
30
34
28
0.9
24
31
37
31
1
27
32
37
44
1.1
31
28
45
30
Mixers - SINGLE & DOUBLE BALANCED - SMT
0
IP3 (dBm)
CONVERSION GAIN (dB)
Upconverter Performance
Conversion Gain vs. LO Drive
LO = 0 dBm
All values in dBc below input LO level measured at RF port
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10 - 4
HMC684LP4 / 684LP4E
v03.0110
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 700 - 1000 MHz
Outline Drawing
Mixers - SINGLE & DOUBLE BALANCED - SMT
10
10 - 5
NOTES:
1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED
PLASTIC SILICA AND SILICON IMPREGNATED.
2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY.
3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN.
4. DIMENSIONS ARE IN INCHES [MILLIMETERS].
5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
6. PAD BURR LENGTH SHALL BE 0.15mm MAX.
PAD BURR HEIGHT SHALL BE 0.25mm MAX.
7. PACKAGE WARP SHALL NOT EXCEED 0.05mm
8. ALL GROUND LEADS AND GROUND PADDLE
MUST BE SOLDERED TO PCB RF GROUND.
9. REFER TO HITTITE APPLICATION NOTE
FOR SUGGESTED PCB LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC684LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC684LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
H684
XXXX
H684
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC684LP4 / 684LP4E
v03.0110
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 700 - 1000 MHz
Pin Descriptions
Pin Number
Description
N/C
No connection. These pins may be connected to RF
ground. Performance will not be affected.
2, 5, 15, 17
GND
Package bottom must be
connected to RF/DC ground.
3
RF
This pin is matched single-ended 50 Ohm and DC
shorted to ground through a balun.
4
TAP
Center tap of secondary side of the internal RF balun.
Short to ground with a zero ohm close to the package.
8, 10, 24
Vcc1, Vcc2,
Vcc3
Power supply voltage. See application circuit
for required external components.
9
LO_BIAS
Adjust the LO buffer current through an external
resistor. See application circuit for required external
components.
16
LO
This pin is matched single-ended 50 Ohm and DC
shorted to ground through a balun.
19
G_BIAS
External optional bias. See application circuit
for required external components.
21, 22
IFN, IFP
Differential IF input / output pins matched to differential
50 Ohms. For applications not requiring operation to
DC an off chip DC blocking capacitor should be used.
Interface Schematic
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10
Mixers - SINGLE & DOUBLE BALANCED - SMT
Function
1, 6, 7, 11 - 14,
18, 20, 23
10 - 6
HMC684LP4 / 684LP4E
v03.0110
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 700 - 1000 MHz
Evaluation PCB
Mixers - SINGLE & DOUBLE BALANCED - SMT
10
List of Materials for Evaluation PCB 119920 [1]
Item
Description
J1 - J3
SMA Connector
J4 - J7
DC Pin
C1, C19
22 pF Capacitor, 0402 Pkg.
C4
6.8 pF Capacitor, 0402 Pkg.
C7, C8
10 nF Capacitor, 0402 Pkg.
C10, C12, C16, C18
1 nF Capacitor, 0402 Pkg.
C11, C15, C17, C21
0.1 µF Capacitor, 0603 Pkg.
C20
4.7 µF Case A, Tantalum
R2 - R4
0 Ohm Resistor, 0402 Pkg.
R5
68 Ohm Resistor, 0402 Pkg.
R9
390 Ohm Resistor, 0603 Pkg.
T1
1:1 Transformer - Tyco MABACT0039
U1
HMC684LP4(E) Downconverter
PCB [2]
118162 Evaluation PCB
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads and exposed paddle should be connected
directly to the ground plane similar to that shown.
A sufficient number of via holes should be used to
connect the top and bottom ground planes. The
evaluation circuit board shown is available from Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Arlon 25R, FR4
10 - 7
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC684LP4 / 684LP4E
v03.0110
BiCMOS MMIC MIXER W/ INTEGRATED
LO AMPLIFIER, 700 - 1000 MHz
Application Circuit
Mixers - SINGLE & DOUBLE BALANCED - SMT
10
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
10 - 8
Similar pages