HDSP-210x Series Eight Character 5 mm and 7 mm Smart Alphanumeric Displays Data Sheet HDSP-210x Series, HDSP-211x Series, HDSP-250x Series Description The HDSP-210x/-211x/-250x series of products is ideal for applications where displaying eight or more characters of dot matrix information in an aesthetically pleasing manner is required. These devices are 8‑digit, 5 x 7 dot matrix, alphanumeric displays and are all packaged in a standard 15.24 mm (0.6 inch) 28 pin DIP. The on-board CMOS IC has the ability to decode 128 ASCII characters which are permanently stored in ROM. In addition, 16 programmable symbols may be stored in on- board ROM, allowing considerable flexibility for displaying additional symbols and icons. Seven brightness levels provide versatility in adjusting the display intensity and power consumption. The HDSP-210x/‑211x/-250x products are designed for standard microprocessor interface techniques. The display and special features are accessed through a bidirectional 8-bit data bus. Features • X stackable (HDSP-21xx) • XY stackable (HDSP-250x) • 128 sharacter ASCII decoder • Programmable functions • 16 user definable characters • Multi-level dimming and blanking • TTL compatible CMOS IC • Wave solderable Applications • Computer peripherals • Industrial instrumentation • Medical equipment • Portable data entry devices • Cellular phones • Telecommunications equipment • Test equipment Device Selection Guide Font Height AlGaAs Red High Efficiency Red Orange Yellow Green 0.2 inches HDSP-2107 HDSP-2112 HDSP-2110 HDSP-2111 HDSP-2113 0.27 inches HDSP-2504 HDSP-2502 HDSP-2500 HDSP-2501 HDSP-2503 Package Dimensions PIN FUNCTION ASSIGNMENT TABLE 42.59 (1.677) 5.33 TYP. (0.210) 28 4.81 (0.189) 19.58 (0.771) 0 1 2 3 4 5 6 7 9.8 (0.386) 1 PIN 1 IDENTIFIER PIN DESIGNATION 2.69 (0.106) FUNCTION PIN # RST 15 FL 16 A0 17 A1 18 A2 19 A3 20 DO NOT CONNECT 21 DO NOT CONNECT 22 DO NOT CONNECT 23 A4 24 CLS 25 CLK 26 WR 27 VDD 28 FUNCTION GND (SUPPLY) GND (LOGIC) CE RD D0 D1 NO PIN NO PIN D2 D3 D4 D5 D6 D7 2.64 SYM. (0.104) LUMINOUS INTENSITY CATEGORY COLOR BIN (NOTE 3) COUNTRY OF ORIGIN PART NUMBER DATE CODE PIN # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 IMAGE PLANE (FOR REFERENCE ONLY) 2.01 (0.08) 0.25 (0.010) [4] HDSP-21XX YYWW 4.79 SYM. (0.189) YZ COO DIA. 0.51 ± 0.13 TYP. (0.020 ± 0.005) 5.31 (0.209) 3.92 TYP. (0.154) 2.54 ± 0.13 TYP. (NON-ACCUM) (0.100 ± 0.005) 2.17 SYM. (0.085) 15.24 (0.600) NOTES: 1. DIMENSIONS ARE IN mm (INCHES). 2. UNLESS OTHERWISE SPECIFIED, TOLERANCE ON ALL DIMENSIONS IS ± 0.25 mm (0.010 INCH). 3. FOR YELLOW AND GREEN DEVICES ONLY. Absolute Maximum Ratings Supply Voltage, VDD to Ground[1] -0.3 to 7.0 V Operating Voltage, VDD to Ground[2] 5.5 V Input Voltage, Any Pin to Ground -0.3 to VDD +0.3 V Free Air Operating Temperature Range, TA[3] -45°C to +85°C Storage Temperature Range, TS -55°C to +100°C Relative Humidity (non-condensing) 85% Soldering Temperature [1.59 mm (0.063 in.) Below Body] Solder Dipping Wave Soldering 260°C for 5 secs 250°C for 3 secs ESD Protection @ 1.5 kΩ, 100 pF VZ = 4 kV (each pin) Notes: 1. Maximum Voltage is with no LEDs illuminated. 2. 20 dots ON in all locations at full brightness. 3. Maximum supply voltage is 5.25 V for operation above 70°C. ESD WARNING: STANDARD CMOS HANDLING PRECAUTIONS SHOULD BE OBSERVED TO AVOID STATIC DISCHARGE. Package Dimensions 70.87 (2.790) PIN FUNCTION ASSIGNMENT TABLE 8.84 TYP. (0.348) 5.08 TYP. (0.200) 4.51 (0.178) 28 6.96 TYP. (0.274) 9.70 (0.382) 0 2 1 3 4 6 5 7 1 PIN DESIGNATION PIN 1 IDENTIFIER LUMINOUS INTENSITY CATEGORY COLOR BIN (NOTE 3) COUNTRY OF ORIGIN PART NUMBER DATE CODE 19.41 (0.764) PIN # FUNCTION PIN # FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 RST FL A0 A1 A2 A3 DO NOT CONNECT DO NOT CONNECT DO NOT CONNECT A4 CLS CLK WR VDD 15 16 17 18 19 20 21 22 23 24 25 26 27 28 GND (SUPPLY) GND (LOGIC) CE RD D0 D1 NO PIN NO PIN D2 D3 D4 D5 D6 D7 IMAGE PLANE (FOR REFERENCE ONLY) 2.01 (0.79) 0.38 (0.015) [4] HDSP-250X YYWW 19.01 SYM. (0.749) YZ COO 2.54 ± 0.13 TYP. (NON-ACCUM) (0.100 ± 0.005) 6.60 (0.260) DIA. 0.51 ± 0.13 TYP. (0.200 ± 0.005) NOTES: 1. DIMENSIONS ARE IN mm (INCHES). 2. UNLESS OTHERWISE SPECIFIED, TOLERANCE ON ALL DIMENSIONS IS ± 0.25 mm (0.010 INCH). 3. FOR YELLOW AND GREEN DEVICES ONLY. 3.91 TYP. (0.154) 2.08 SYM. (0.082) 15.24 (0.600) ASCII Character Set HDSP-210X, HDSP-211X, HDSP-250X Series D7 D6 BIT S 0 0 D5 0 D4 D3 D2 D1 D0 COLUMN ROW 0 0 0 0 0 0 0 1 1 1 2 0 0 0 1 3 0 1 1 0 0 1 0 4 0 5 0 1 1 1 0 1 0 6 1 1 X 1 7 X X 8–F 0000 0 16 0001 1 0010 2 U S E R 0011 3 0100 4 0101 5 0110 6 0111 7 1000 8 1001 9 1010 A 1011 B 1100 C 1101 D 1110 E 1111 F D E F I N E D C H A R A C T E R S Recommended Operating Conditions Parameter Symbol Minimum Nominal Maximum Units Supply Voltage 4.5 5.0 5.5 V VDD Electrical Characteristics Over Operating Temperature Range (-45°C to +85°C) 4.5 V < VDD < 5.5 V, unless otherwise specified TA = 25°C -45°C < TA < + 85°C VDD = 5.0 4.5 V < VDD < 5.5 V Parameter Symbol Typ. Max. Min. Max. Units Test Conditions Input Leakage IIH 1.0 µA (Input without pullup) IIL -1.0 VIN = 0 to VDD, pins CLK, D0-D A0-A4 Input Current IIPL -11 -18 -30 µA (Input with pullup) VIN = 0 to VDD, pins CLS, RST, WR, RD, CE, FL IDD Blank IDD (BLK) 0.5 3.0 4.0 mA VIN = VDD IDD 8 digits IDD(V) 200 255 330 mA 12 dots/character[1,2] “V” on in all 8 locations IDD 8 digits IDD(#) 300 370 430 mA 20 dots/character[1,2,3,4] “#” on in al locations Input Voltage High VIH 2.0 VDD +0.3 V Input Voltage Low VIL 0.8 V GND -0.3 V Output Voltage High VOH 2.4 V VDD = 4.5 V, IOH = -40 µA Output Voltage Low VOL 0.4 V D0-D7 VDD = 4.5 V, IOL = 1.6 mA Output Voltage Low VOL 0.4 V CLK VDD = 4.5 V, IOL = 40 µA High Level Output Current IOH -60 mA VDD = 5.0 V Low Level Output Current IOL 50 mA VDD = 5.0 V Thermal Resistance IC Junction-to-Case RqJ-C 15 °C/W Notes: 1. Average IDD measured at full brightness. See Table 2 in Control Word Section for IDD at lower brightness levels. Peak IDD = 28/15 x IDD (#). 2. Maximum IDD occurs at -55°C. 3. Maximum IDD(#) = 355 mA at VDD = 5.25 V and IC TJ = 150°C. 4. Maximum IDD(#) = 375 mA at VDD = 5.5 V and IC TJ = 150°C. Optical Characteristics at 25°C[1] VDD = 5.0 V at Full Brightness Part Description Number Luminous Intensity Character Average (#) Iv (mcd) Min. Typ. Peak Wavelength lPeak (nm) Dominant Wavelength ld (nm) AlGaAs HDSP-2107 -2504 8.0 15.0 645 637 HER HDSP-2112 -2502 2.5 7.5 635 626 Orange HDSP-2110 -2500 2.5 7.5 600 602 Yellow HDSP-2111 -2501 2.5 7.5 583 585 High Performance HDSP-2113 Green -2503 2.5 7.5 568 574 Note: 1. Refers to the initial case temperature of the device immediately prior to measurement. AC Timing Characteristics Over Temperature Range (-45°C to +85°C) 4.5 V < VDD < 5.5 V, unless otherwise specified Reference Number Symbol Description Min.[1] 1 tACC Display Access Time Write Read 210 230 ns 2 10 ns tACS Address Setup Time to Chip Enable Units 3 tCE Chip Enable Active Time[2,3] Write Read 140 160 ns 4 tACH Address Hold Time to Chip Enable 20 ns 5 tCER Chip Enable Recovery Time 60 ns 6 tCES Chip Enable Active Prior to Rising Edge of[2,3] Write Read 140 160 ns 7 tCEH Chip Enable Hold Time to Rising Edge of Read/Write Signal[2,3] 0 ns 8 tW Write Active Time 100 ns 9 tWSU Data Write Setup Time 50 ns 10 tWH Data Write Hold Time 20 ns 11 tR Chip Enable Active Prior to Valid Data 160 ns 12 tRD Read Active Prior to Valid Data 75 ns 13 tDF Read Data Float Delay 10 ns tRC Reset Active Time[4] 300 ns Notes: 1. Worst case values occur at an IC junction temperature of 150°C. 2. For designers who do not need to read from the display, the Read line can be tied to VDD and the Write and Chip Enable lines can be tied together. 3. Changing the logic levels of the Address lines when CE = “0” may cause erroneous data to be entered into the Character RAM, regardless of the logic levels of the WR and RD lines. 4. The display must not be accessed until after 3 clock pulses (110 µs min. using the internal refresh clock) after the rising edge of the reset line. AC Timing Characteristics Over Temperature Range (-45°C to +85°C) 4.5 V < VDD < 5.5 V, unless otherwise specified Symbol Description 25°C Typ. Min.[1] Units FOSC Oscillator Frequency 57 28 kHz FRF[2] Display Refresh Rate 256 128 Hz FFL[3] Character Flash Rate 2 1 Hz tST[4] Self Test Cycle Time 4.6 9.2 sec Notes: 1. Worst case values occur at an IC junction temperature of 150°C. 2. FRF = FOSC/224. 3. FFL = FOSC/28,672. 4. tST = 262,144/FOSC. Write Cycle Timing Diagram 1 A0 -A4 FL 4 2 3 CE 6 7 8 WR 10 9 D0 -D7 INPUT PULSE LEVELS: 0.6 V to 2.4 V 2 5 Read Cycle Timing Diagram 1 A0 -A4 FL 4 2 CE 6 7 11 RD 12 D0 -D7 INPUT PULSE LEVELS: 0.6 V to 2.4 V OUTPUT REFERENCE LEVELS: 0.6 V to 2.2 V OUTPUT LOADING = 1 TTL LOAD AND 100 pF Relative Luminous Intensity vs. Temperature RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 25°C) 3.5 3.0 HER HDSP-2112/2502 ORANGE HDSP-2110/2500 YELLOW HDSP-2111/2501 2.5 2.0 1.5 GREEN 1.0 HDSP-2113/2503 0.5 0 -55 -45 -35 -15 5 25 45 65 TA – AMBIENT TEMPERATURE – °C 85 2 5 3 13 Electrical Description Pin Function Description RESET (RST, pin 1) Initializes the display. FLASH (FL, pin 2) FL low indicates an access to the Flash RAM and is unaffected by the state of address lines A3-A4. ADDRESS INPUTS (A0-A4, pins 3-6, 10) Each location in memory has a distinct address. Address inputs (A 0 -A 2 ) select a specific location in the Character RAM, the Flash RAM or a particular row in the UDC (User-Defined Character) RAM. A 3-A 4 are used to select which section of memory is accessed. Table 1 shows the logic levels needed to access each section of memory. Table 1. Logic Levels to Access Memory Section of Memory FL A4 A3 A2 A1 A0 Flash RAM 0 X X Char. Address UDC Address Register 1 0 0 Don’t Care UDC RAM 1 0 1 Row Address Control Word Register 1 1 0 Don’t Care Character RAM 1 1 1 Character Address CLOCK SELECT (CLS, pin 11) Used to select either an internal (CLS = 1) or external (CLS = 0) clock source. CLOCK INPUT/OUTPUT (CLK, pin 12) Outputs the master clock (CLS = 1) or inputs a clock (CLS = 0) for slave displays. WRITE (WR, pin 13) Data is written into the display when the WR input is low and the CE input is low. CHIP ENABLE (CE, pin 17) Must be at a logic low to read or write data to the display and must go high between each read and write cycle. READ (RD, pin 18) Data is read from the display when the RD input is low and the CE input is low. DATA Bus (D0-D7, pins 19, 20, 23-28) Used to read from or write to the display. GND (SUPPLY) (pin 15) Analog ground for the LED drivers. GND (LOGIC) (pin 16) Digital ground for internal logic. VDD (POWER) (pin 14) Positive power supply input. 10 CLS CLK RST RD WR D0-D7 A0-A2 A3 A4 FL CE OCS A3 A4 FL CE A3 A4 FL CE UDC ADDR CLR1 RESET A3 A4 FL CE INTENSITY FLASH BLINK RESET CLOCK FLASH TEST OK CLR2 TIMING AND CONTROL TEST OK SELF TEST SELF TEST IN VISUAL TEST ROM TEST SELF TEST CLR START TIMING ROW SET CHAR ADDR EN FLASH RD DATA WR FLASH D0 RAM A0-A2 RESET CHAR ADDR 8x8 EN CHARACTER RD D0-D6 RAM WR D7 D0-D7 A0-A2 RESET CHAR ADDR Figure 1. HDSP-210X/-211X/-212X/-250X internal block diagram. CONTROL WORD REGISTER EN 0 INTENSITY RD 1 WR 2 FLASH D0-D7 3 BLINK 4 RESET SELF TEST 6 SELF TEST 7 RESULT FL CE A3 A4 FL CE PRE SET CLR RD WR D0-D7 EN UDC ADDR REGISTER UDC RAM ROW SEL SELF TEST DOT DATA ASCII DECODER D0-D6 EN EN RD WR DOT D0-D4 A0-A2 DATA UDC ADDR ROW SET EN D0-D4 TIMING DOT DRIVERS DOT DATA TIMING ROW DRIVERS 8 5x7 LED CHARACTERS Display Internal Block Diagram Figure 1 shows the internal block diagram of the HDSP210X/‑211X/-250X displays. The CMOS IC consists of an 8 byte Character RAM, an 8 bit Flash RAM, a 128 character ASCII decoder, a 16 character UDC RAM, a UDC Address Register, a Control Word Register, and refresh circuitry necessary to synchronize the decoding and driving of eight 5 x 7 dot matrix characters. The major user-accessible portions of the display are listed below: Character RAM This RAM stores either ASCII character data or a UDC RAM address. Flash RAM This is a 1 x 8 RAM which stores Flash data. User-Defined Character RAM (UDC RAM) This RAM stores the dot pattern for custom characters. User-Defined Character Address Register (UDC Address Register) This register is used to provide the address to the UDC RAM when the user is writing or reading a custom character. Control Word Register This register allows the user to adjust the display brightness, flash individual characters, blink, self test, or clear the display. Character RAM Figure 2 shows the logic levels needed to access the HDSP-210X/-211X/-250X Character RAM. During a normal access, the CE = “0” and either RD = “0” or WR = “0.” However, erroneous data may be written into the Character RAM if the address lines are unstable when CE = “0” regardless of the logic levels of the RD or WR lines. Address lines A0-A2 are used to select the location in the Character RAM. Two types of data can be stored in each Character RAM location: an ASCII code or a UDC RAM address. Data bit D7 is used to differentiate between the ASCII character and a UDC RAM address. D7 = 0 enables the ASCII decoder and D7 = 1 enables the UDC RAM. D0D6 are used to input ASCII data and D0-D3 are used to input a UDC address. RST CE 1 0 WR 0 0 1 1 RD 0 1 0 1 UNDEFINED WRITE TO DISPLAY READ FROM DISPLAY UNDEFINED CONTROL SIGNALS FL A4 A3 1 1 1 A2 A1 A0 000 = LEFT MOST 111 = RIGHT MOST CHARACTER ADDRESS CHARACTER RAM ADDRESS D7 D6 D5 0 D4 D3 D2 D1 D0 128 ASCII CODE 1 X X X UDC CODE CHARACTER RAM DATA FORMAT DIG0 DIG1 DIG2 DIG3 DIG4 DIG5 DIG6 DIG7 000 001 010 011 100 101 110 111 SYMBOL IS ACCESSED IN LOCATION SPECIFIED BY THE CHARACTER ADDRESS ABOVE DISPLAY 0 = LOGIC 0; 1 = LOGIC 1; X = DO NOT CARE Figure 2. Logic levels to access the character RAM. 11 UDC RAM and UDC Address Register Figure 3 shows the logic levels needed to access the UDC RAM and the UDC Address Register. The UDC Address Register is eight bits wide. The lower four bits (D0-D3) are used to select one of the 16 UDC locations. The upper four bits (D4-D7) are not used. Once the UDC address has been stored in the UDC Address Register, the UDC RAM can be accessed. To completely specify a 5 x 7 character, eight write cycles are required. One cycle is used to store the UDC RAM address in the UDC Address Register and seven cycles are used to store dot data in the UDC RAM. Data is entered by rows and one cycle is needed to access each row. Figure 4 shows the organization of a UDC character assuming the symbol to be stored is an “F.” A0-A2 are used to select the row to be accessed and D0-D4 are used to transmit the row dot data. The upper three bits (D5-D7) are ignored. D0 (least significant bit) corresponds to the right most column of the 5 x 7 matrix and D4 (most significant bit) corresponds to the left most column of the 5 x 7 matrix. Flash RAM Figure 5 shows the logic levels needed to access the Flash RAM. The Flash RAM has one bit associated with each location of the Character RAM. The Flash input is used to select the Flash RAM while address lines A3-A4 are ignored. Address lines A0-A2 are used to select the location in the Flash RAM to store the attribute. D0 is used to store or remove the flash attribute. D0 = “1” stores the attribute and D0 = “0” removes the attribute. When the attribute is enabled through bit 3 of the Control Word and a “1” is stored in the Flash RAM, the corresponding character will flash at approximately 2 Hz. The actual rate is dependent on the clock frequency. For an external clock the flash rate can be calculated by dividing the clock frequency by 28,672. RST CE 1 0 WR 0 0 1 1 RD 0 1 0 1 UNDEFINED WRITE TO DISPLAY READ FROM DISPLAY UNDEFINED CONTROL SIGNALS FL A4 A3 A2 A1 A0 1 0 0 X X X UDC ADDRESS REGISTER ADDRESS D7 D6 D5 D4 X X X X D3 D2 D1 D0 UDC CODE UDC ADDRESS REGISTER DATA FORMAT RST CE 1 0 WR 0 0 1 1 RD 0 1 0 1 UNDEFINED WRITE TO DISPLAY READ FROM DISPLAY UNDEFINED CONTROL SIGNALS FL A4 A3 1 0 1 A2 A1 A0 ROW SELECT 000 = ROW 1 110 = ROW 7 UDC RAM ADDRESS D7 D6 D5 X X X D4 D3 D2 D1 D0 DOT DATA UDC RAM DATA FORMAT C O L 1 0 = LOGIC 0; 1 = LOGIC 1; X = DO NOT CARE Figure 3. Logic levels to access a UDC character. C C C O O O L L L 1 2 3 D 4 D 3 D2 1 1 1 1 0 0 1 0 0 1 1 1 1 0 0 1 0 0 1 0 0 IGNORED C O L 4 D1 1 0 0 1 0 0 0 C O L 5 D0 1 0 0 0 0 0 0 ROW 1 ROW 2 ROW 3 ROW 4 ROW 5 ROW 6 ROW 7 UDC CHARACTER • • • • • • • • • • • • • • 0 = LOGIC 0; 1 = LOGIC 1; * = ILLUMINATED LED Figure 4. Data to load “”F’’ into the UDC RAM. 12 C O L 5 HEX CODE 1F 10 10 1D 10 10 10 Control Word Register Figure 6 shows how to access the Control Word Register. This 8-bit register performs five functions: Brightness control, Flash RAM control, Blinking, Self Test, and Clear. Each function is independent of the others; however, all bits are updated during each Control Word write cycle. Brightness (Bits 0-2) Bits 0-2 of the Control Word adjust the brightness of the display. Bits 0-2 are interpreted as a three bit binary code with code (000) corresponding to maximum brightness and code (111) corresponding to a blanked display. In addition to varying the display brightness, bits 0-2 also vary the average value of IDD. IDD can be calculated at any brightness level by multiplying the percent brightness level by the value of IDD at the 100% brightness level. These values of IDD are shown in Table 2. Flash Function (Bit 3) Bit 3 determines whether the flashing character attribute is on or off. When bit 3 is a“1,” the output of the Flash RAM is checked. If the content of a location in the Flash RAM is a “1,” the associated digit will flash at approximately 2 Hz. For an external clock, the blink rate can be calculated by driving the clock frequency by 28,672. If the flash enable bit of the Control Word is a “0,” the content of the Flash RAM is ignored. To use this function with multiple display systems, see the Display Reset section. Blink Function (Bit 4) Bit 4 of the Control Word is used to synchronize blinking of all eight digits of the display. When this bit is a “1” all eight digits of the display will blink at approximately 2 Hz. The actual rate is dependent on the clock frequency. For an external clock, the blink rate can be calculated by dividing the clock frequency by 28,672. This function will override the Flash function when it is active. To use this function with multiple display systems, see the Display Reset section. RST CE 1 0 WR 0 0 1 1 RD 0 1 0 1 UNDEFINED WRITE TO DISPLAY READ FROM DISPLAY UNDEFINED CONTROL SIGNALS FL A4 A3 0 X X A2 A1 A0 000 = LEFT MOST 111 = RIGHT MOST CHARACTER ADDRESS FLASH RAM ADDRESS D7 D6 D5 D4 D3 D2 D1 D0 X X X X X X X 0 1 REMOVE FLASH AT SPECIFIED DIGIT LOCATION STORE FLASH AT SPECIFIED DIGIT LOCATION FLASH RAM DATA FORMAT 0 = LOGIC 0; 1 = LOGIC 1; X = DO NOT CARE Figure 5. Logic levels to access the flash RAM. RST CE 1 0 WR 0 0 1 1 RD 0 1 0 1 UNDEFINED WRITE TO DISPLAY READ FROM DISPLAY UNDEFINED CONTROL SIGNALS FL A4 A3 A2 A1 A0 1 1 0 X X X CONTROL WORD ADDRESS D7 D6 D5 D4 D3 D2 D1 D0 C S S BL F B B B 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 DISABLE FLASH 1 ENABLE FLASH 0 1 0 1 0 1 0 1 0 DISABLE BLINKING 1 ENABLE BLINKING 0 1 X NORMAL OPERATION; X IS IGNORED X START SELF TEST; RESULT GIVEN IN X X = 0 FAILED X = 1 PASSED 0 NORMAL OPERATION 1 CLEAR FLASH AND CHARACTER RAMS CONTROL WORD DATA FORMAT 0 = LOGIC 0; 1 = LOGIC 1; X = DO NOT CARE Figure 6. Logic levels to access the control word register Table 2. Current Requirements at Different Brightness Levels VDD = 5.0 V % Current at 25°C Symbol D2 D1 D0 Brightness Typ. IDD (V) 13 0 0 0 0 1 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 100 80 53 40 27 20 13 200 160 106 80 54 40 26 Units mA mA mA mA mA mA mA 100% 80% 53% BRIGHTNESS 40% CONTROL 27% LEVELS 20% 13% 0% Self Test Function (Bits 5, 6) Bit 6 of the Control Word Register is used to initiate the self test function. Results of the internal self test are stored in bit 5 of the Control Word. Bit 5 is a read only bit where bit 5 = “1” indicates a passed self test and bit 5 = “0” indicates a failed self test. Setting bit 6 to a logic 1 will start the self test function. The built-in self test function of the IC consists of two internal routines which exercise major portions of the IC and illuminate all of the LEDs. The first routine cycles the ASCII decoder ROM through all states and performs a checksum on the output. If the checksum agrees with the correct value, bit 5 is set to “1.” The second routine provides a visual test of the LEDs using the drive circuitry. This is accomplished by writing checkered and inverse checkered patterns to the display. Each pattern is displayed for approximately 2 seconds. During the self test function the display must not be accessed. The time needed to execute the self test function is calculated by multiplying the clock period by 262,144. For example, assume a clock frequency of 58 KHz, then the time to execute the self test function frequency is equal to (262,144/58,000) = 4.5 second duration. At the end of the self test function, the Character RAM is loaded with blanks, the Control Word Register is set to zeros except for bit 5, the Flash RAM is cleared, and the UDC Address Register is set to all ones. Clear Function (Bit 7) Bit 7 of the Control Word will clear the Character RAM and the Flash RAM. Setting bit 7 to a “1” will start the clear function. Three clock cycles (110 ms minimum using the internal refresh clock) are required to complete the clear function. The display must not be accessed while the display is being cleared. When the clear function has been completed, bit 7 will be reset to a “0.” The ASCII character code for a space (20H) will be loaded into the Character RAM to blank the display and the Flash RAM will be loaded with “0”s. The UDC RAM, UDC Address Register, and the remainder of the Control Word are unaffected. RST CE WR RD FL 0 1 X X X A4 -A0 D7 -D0 X X 0 = LOGIC 0; 1 = LOGIC 1; X = DO NOT CARE NOTE: IF RST, CE, AND WR ARE LOW, UNKNOWN DATA MAY BE WRITTEN INTO THE DISPLAY. Figure 7. Logic levels to reset the display. 14 Display Reset Figure 7 shows the logic levels needed to Reset the display. The display should be Reset on Power-up. The external Reset clears the Character RAM, Flash RAM, Control Word and resets the internal counters. After the rising edge of the Reset signal, three clock cycles (110 µs minimum using the internal refresh clock) are required to complete the reset sequence. The display must not be accessed while the display is being reset. The ASCII Character code for a space (20H) will be loaded into the Character RAM to blank the display. The Flash RAM and Control Word Register are loaded with all “0”s. The UDC RAM and UDC Address Register are unaffected. All displays which operate with the same clock source must be simultaneously reset to synchronize the Flashing and Blinking functions. Mechanical and Electrical Considerations The HDSP-210X/-211X/‑250X are 28 pin dual-in-line packages with 26 external pins. The devices can be stacked horizontally and vertically to create arrays of any size. The HDSP-210X/-211X/-250X are designed to operate continuously from -45°C to +85°C with a maximum of 20 dots on per character at 5.25 V. Illuminating all thirty-five dots at full brightness is not recommended. The HDSP-210X/-211X/‑250X are assembled by die attaching and wire bonding 280 LED chips and a CMOS IC to a thermally conductive printed circuit board. A polycarbonate lens is placed over the PC board creating an air gap over the LED wire bonds. A protective cap creates an air gap over the CMOS IC. Backfill epoxy environmentally seals the display package. This package construction makes the display highly tolerant to temperature cycling and allows wave soldering. The inputs to the IC are protected against static discharge and input current latchup. However, for best results standard CMOS handling precautions should be used. Prior to use, the HDSP-210X/-211X/-250X should be stored in antistatic tubes or in conductive material. During assembly, a grounded conductive work area should be used, and assembly personnel should wear conductive wrist straps. Lab coats made of synthetic material should be avoided since they are prone to static buildup. Input current latchup is caused when the CMOS inputs are subjected to either a voltage below ground (VIN < ground) or to a voltage higher than VDD (VIN > VDD) and when a high current is forced into the input. To prevent input current latchup and ESD damage, unused inputs should be connected either to ground or to VDD. Voltages should not be applied to the inputs until VDD has been applied to the display. Thermal Considerations The HDSP-210X/-211X/-212X/250X have been designed to provide a low thermal resistance path for the CMOS IC to the 26 package pins. Heat is typically conducted through the traces of the printed circuit board to free air. For most applications no additional heatsinking is required. Measurements were made on a 32 character display string to determine the thermal resistance of the display assembly. Several display boards were constructed using 0.062 in. thick printed circuit material, and one ounce copper 0.020 in. traces. Some of the device pins were connected to a heatsink formed by etching a copper area on the printed circuit board surrounding the display. A maximally metallized printed circuit board was also evaluated. The junction temperature was measured for displays soldered directly to these PC boards, displays installed in sockets, and finally displays installed in sockets with a filter over the display to restrict airflow. The results of these thermal resistance measurements, RqJ-A are shown in Table 3 and include the effects of RqJ-C. Ground Connections Two ground pins are provided to keep the internal IC logic ground clean. The designer can, when necessary, route the analog ground for the LED drivers separately from the logic ground until an appropriate ground plane is available. On long interconnections between the display and the host system, the designer can keep voltage drops on the analog ground from affecting the display logic levels by isolating the two grounds. Soldering and Post Solder Cleaning Instructions for the HDSP-210X/-211X/‑250X The HDSP-210X/-211X/-250X may be hand soldered or wave soldered with SN63 solder. When hand soldering, it is recommended that an electronically temperature controlled and securely grounded soldering iron be used. For best results, the iron tip temperature should be set at 315°C (600°F). For wave soldering, a rosin-based RMA flux can be used. The solder wave temperature should be set at 245°C ± 5°C (473°F ± 9°F), and the dwell in the wave should be set between 11 /2 to 3 seconds for optimum soldering. The preheat temperature should not exceed 105°C (221°F) as measured on the solder side of the PC board. For additional information on soldering and post solder cleaning, see Application Note 1027, Soldering LED Components. Contrast Enhancement The objective of contrast enhancement is to provide good readability in a variety of ambient lighting conditions. For information on contrast enhancement see Application Note 1015, Contrast Enhancement Techniques for LED Displays. The logic ground should be connected to the same ground potential as the logic interface circuitry. The analog ground and the logic ground should be connected at a common ground which can withstand the current introduced by the switching LED drivers. When separate ground connections are used, the analog ground can vary from -0.3 V to +0.3 V with respect to the logic ground. Voltage below -0.3 V can cause all dots to be on. Voltage above +0.3 V can cause dimming and dot mismatch. Table 3. Thermal Resistance, qJA, Using Various Amounts of Heatsinking Material Heatsinking Metal W/Sockets W/O Sockets per Device W/O Filter W/O Filter sq. in. (Avg.) (Avg.) W/Sockets W/Filter (Avg.) Units 0 31 30 35 °C/W 1 31 28 33 °C/W 3 30 26 33 °C/W Max. Metal 29 25 32 °C/W 4 Board Avg 30 27 33 °C/W Intensity Bin Limits for HDSP-2107 Intensity Range (mcd) Bin Min. Max. Color Bin Limits Color Bin Color Range (nm) Min. Max. I 5.12 9.01 Yellow 3 581.5 585.0 J 7.68 13.52 4 584.0 587.5 K 11.52 20.28 5 586.5 590.0 L 17.27 30.42 6 589.0 592.5 M 25.39 45.63 7 591.5 595.0 1 576.0 580.0 2 573.0 577.0 3 570.0 574.0 4 567.0 571.5 Note: Test conditions as specified in Optical Characteristic table. Intensity Bin Limits for HDSP-211x and HDSP-250x (Except HDSP-2504) Intensity Range (mcd) Bin Min. Max. G 2.50 4.00 H 3.41 6.01 I 5.12 9.01 J 7.68 13.52 K 11.52 20.28 Green Note: Test conditions as specified in Optical Characteristic table. Note: Test conditions as specified in Optical Characteristic table. Intensity Bin Limit for HDSP-2504 Intensity Range (mcd) Bin Min. Max J 7.68 13.52 K 11.52 20.28 L 17.27 30.42 M 25.91 45.63 Note: Test conditions as specified in Optical Characteristic table. For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2005-2008 Avago Technologies Limited. All rights reserved. Obsoletes 5989-3183EN AV02-0629EN - May 9, 2008