LINER LT1675 650mhz gain of 2 triple 2 1video multiplexer Datasheet

LT6555
650MHz Gain of 2 Triple
2:1Video Multiplexer
U
FEATURES
DESCRIPTIO
■
The LT®6555 is a high speed triple 2:1 video multiplexer
with an internally fixed gain of 2. The individual amplifiers
are optimized for performance with a double terminated
75Ω video load and feature a –3dB 2VP-P bandwidth of
450MHz, making them ideal for driving very high resolution video signals. Separate power supply pins for each
amplifier boost channel separation to 72dB, allowing the
LT6555 to excel in many high speed applications.
■
■
■
■
■
■
■
■
■
■
■
■
■
650MHz –3dB Small Signal Bandwidth
450MHz –3dB 2VP-P Large-Signal Bandwidth
120MHz ±0.1dB Bandwidth
High Slew Rate: 2200V/µs
Fixed Gain of 2; No External Resistors Required
72dB Channel Separation at 10MHz
50dB Channel Separation at 100MHz
–80dBc 2nd Harmonic Distortion at 10MHz, 2VP-P
–70dBc 3rd Harmonic Distortion at 10MHz, 2VP-P
Low Supply Current: 9mA per Amplifier
6.5ns 0.1% Settling Time for 2V Step
ISS ≤ 500µA per Amplifier when Disabled
Differential Gain of 0.033%, Differential
Phase of 0.022°
Wide Supply Range: ±2.25V (4.5V) to ±6V (12V)
Available in 24-Lead SSOP and 24-Lead QFN
Packages
While the performance of the LT6555 is optimized for dual
supply operation, it can also be operated with a single
supply as low as 4.5V. Using dual 5V supplies, each
amplifier draws only 9mA. When disabled, the amplifiers
draw less than 500µA and the outputs become high
impedance.
U
APPLICATIO S
The LT6555 is manufactured on Linear Technology’s
proprietary low voltage complementary bipolar process
and is available in 24-lead SSOP and ultra-compact
24-lead QFN packages.
■
, LTC and LT are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
■
■
RGB Amplifiers
UXGA Video Multiplexing
LCD Projectors
U
■
TYPICAL APPLICATIO
RGB Multiplexer and Line Driver
V+
RINA
GINA
BINA
LT6555
75Ω
×2
Video Amplitude Transient Response
75Ω
ROUT
1.8
75Ω
75Ω
1.6
1.4
×2
75Ω
GOUT
75Ω
RINB
GINB
BINB
75Ω
OUTPUT (V)
1.2
75Ω AGND
1.0
0.8
0.6
0.4
0.2
×2
75Ω
BOUT
75Ω
SELECT A/B
75Ω
VIN = 0V TO 700mV
VS = ±5V
RL = 150Ω
TA = 25°C
0
75Ω
ENABLE
–0.2
–0.4
0
2
4
6
8 10 12 14 16 18 20
TIME (ns)
6555 G21
DGND
V–
6555 TA01a
6555f
1
LT6555
U
W W
W
ABSOLUTE
AXI U RATI GS
(Note 1)
Total Supply Voltage (V+ to V–) ............................ 12.6V
Input Current (Note 2) ........................................ ±10mA
Output Current (Continuous) ............................. ±70mA
EN to DGND Voltage (Note 2) ................................. 5.5V
SEL to DGND Voltage (Note 2) .................................. 8V
Output Short-Circuit Duration (Note 3) ............ Indefinite
Operating Temperature Range (Note 4) ... –40°C to 85°C
Specified Temperature Range (Note 5) .... –40°C to 85°C
Junction Temperature
SSOP ................................................................ 150°C
QFN .................................................................. 125°C
Storage Temperature Range
SSOP ................................................. –65°C to 150°C
QFN ................................................... –65°C to 125°C
Lead Temperature (Soldering, 10 sec)
SSOP ................................................................ 300°C
U
W
U
PACKAGE/ORDER I FOR ATIO
IN2A
22 SEL A/B
VREF
4
21 V+
IN3A
5
AGND1
6
IN1B
7
17 OUT1
16 V–
25
V– 4
18 OUT2
17
IN3A 2
15 OUT2
14 V+
IN1B 5
V+
AGND2 6
AGND3 10
15 V–
IN3B 11
14 V+
V–
12
13
V+
V
V–
9 10 11 12
+
8
V+
7
G = +2
UF PART*
MARKING
13 OUT3
16 OUT3
IN3B
9
18 V+
AGND1 3
19 V–
G = +2
VREF 1
IN2B
8
IN2B
20 OUT1
LT6555CUF
LT6555IUF
24 23 22 21 20 19
AGND3
AGND2
G = +2
LT6555CGN
LT6555IGN
ORDER PART
NUMBER
SEL A/B
23 EN
3
EN
24
2
V+
1
TOP VIEW
IN1A
IN1A
DGND
ORDER PART
NUMBER
DGND
V+
IN2A
TOP VIEW
6555
UF PACKAGE
24-LEAD (4mm × 4mm) PLASTIC QFN
TJMAX = 125°C, θJA = 37°C/W, θJC = 2.6°C/W
EXPOSED PAD (PIN 25) IS V –
MUST BE SOLDERED TO PCB
GN PACKAGE
24-LEAD PLASTIC SSOP
TJMAX = 150°C, θJA = 90°C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±5V, RL = 150Ω, CL = 1.5pF, VEN = 0.4V, VAGND, VDGND, VVREF = 0V.
SYMBOL
PARAMETER
CONDITIONS
VOS
Input Referred Offset Voltage
VIN = 0V, VOS = VOUT/2
MIN
TYP
MAX
UNITS
5
±16
±24
mV
mV
–17
±45
µA
●
●
IIN
Input Current
RIN
Input Resistance
VIN = ±1V
CIN
Input Capacitance
f = 100kHz
PSRR
Power Supply Rejection Ratio
VS = ±2.25V to ±6V (Note 6)
●
●
IPSRR
Input Current Power Supply Rejection
VS = ±2.25V to ±6V (Note 6)
●
AV ERR
Gain Error
VOUT = ±2V, Nominal Gain 2V/V
●
AV MATCH
Gain Matching
Any One Channel to Another
VOUT
Output Voltage Swing
(Note 7)
●
100
56
400
kΩ
1
pF
62
dB
1
±4
±2.5
±3.15
±3.0
µA/V
%
±0.33
%
±3.4
V
V
6555f
2
LT6555
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±5V, RL = 150Ω, CL = 1.5pF, VEN = 0.4V, VAGND, VDGND, VVREF = 0V.
SYMBOL
PARAMETER
CONDITIONS
IS
Supply Current, Per Amplifier
RL = ∞
MIN
TYP
MAX
9
12
14
mA
mA
47
42
500
500
µA
µA
●
UNITS
Supply Current, Disabled, Per Amplifier
VEN = 4V, RL = ∞
VEN = Open, RL = ∞
●
●
IEN
Enable Pin Current
VEN = 0.4V
VEN = 4V
●
●
–200
–75
–95
–21
µA
µA
ISEL
Select Pin Current
VSEL = 0.4V
VSEL = 4V
●
●
–50
–50
–5
–1
µA
µA
ISC
Output Short-Circuit Current
RL = 0Ω, VIN = ±1V
●
±50
±105
mA
SR
Slew Rate
±1V on ±2.5V Output Step (Note 8)
1600
2200
V/µs
–3dB BW
Small-Signal –3dB Bandwidth
VOUT = 200mVP-P
650
MHz
0.1dB BW
Gain Flatness ±0.1dB Bandwidth
VOUT = 200mVP-P
120
MHz
FPBW
tS
Full Power Bandwidth 2V
VOUT = 2VP-P (Note 9)
350
MHz
Full Power Bandwidth 4V
VOUT = 4VP-P (Note 9)
250
175
MHz
All-Hostile Crosstalk
f = 10MHz, VIN = 1VP-P
f = 100MHz, VIN = 1VP-P
–72
–50
dB
dB
Selected Channel to Unselected
Channel Crosstalk
f = 10MHz, VIN = 1VP-P
f = 100MHz, VIN = 1VP-P
–80
–55
dB
dB
Channel Select Output Transient
INA = INB = 0V
200
mVP-P
Channel-to-Channel Select Time
INA = –1V, INB = 1V
from 50% SEL to VOUT = 0V
8
ns
Settling Time
0.1% of VFINAL, VSTEP = 2V
6.5
ns
tR, tF
Small-Signal Rise and Fall Time
10% to 90%, VOUT = 400mVP-P
520
ps
dG
Differential Gain
(Note 10)
0.033
%
dP
Differential Phase
(Note 10)
0.022
Deg
HD2
2nd Harmonic Distortion
f = 10MHz, VOUT = 2VP-P
–80
dBc
HD3
3rd Harmonic Distortion
f = 10MHz, VOUT = 2VP-P
–70
dBc
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: This parameter is guaranteed to meet specified performance
through design and characterization. It is not production tested.
Note 3: As long as output current and junction temperature are kept below
the Absolute Maximum Ratings, no damage to the part will occur.
Depending on the supply voltage, a heat sink may be required.
Note 4: The LT6555C is guaranteed functional over the operating
temperature range of –40°C to 85°C.
Note 5: The LT6555C is guaranteed to meet specified performance from
0°C to 70°C. The LT6555C is designed, characterized and expected to
meet specified performance from –40°C and 85°C but is not tested or QA
sampled at these temperatures. The LT6555I is guaranteed to meet
specified performance from –40°C to 85°C.
Note 6: In order to follow the constraints for 4.5V operation for PSRR
and IPSRR testing at ±2.25V, the DGND pin is set to V–, the EN pin is set
to V– + 0.4V, and the SEL pin is set to either V– + 0.4V or V– + 4V. At ±6V
and all other cases, DGND is set to ground and the EN and SEL pins are
referenced from it.
Note 7: The VREF pin is set to 1V when testing positive swing and –1V
when testing negative swing to ensure that the internal input clamps do
not limit the output swing.
Note 8: Slew rate is 100% production tested using both inputs of
channel 2. Slew rates of channels 1 and 3 are guaranteed through
design and characterization.
Note 9: Full power bandwidth is calculated from the slew rate:
FPBW = SR/(π • VP-P)
Note 10: Differential gain and phase are measured using a Tektronix
TSG120YC/NTSC signal generator and a Tektronix 1780R video
measurement set. The resolution of this equipment is better than 0.05%
and 0.05°. Nine identical amplifier stages were cascaded giving an
effective resolution of better than 0.0056% and 0.0056%.
6555f
3
LT6555
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Supply Current per Amplifier
vs Temperature
VEN = 0V
VEN = 0.4V
8
12
VEN, VIN, VDGND, VSEL = 0V
TA = 25°C
10
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
10
12
VS = ±5V
RL = ∞
VIN = 0V
6
4
2
VS = ±5V
RL = ∞
VIN = 0V
10
SUPPLY CURRENT (mA)
12
Supply Current per Amplifier
vs EN Pin Voltage
Supply Current per Amplifier
vs Supply Voltage
8
6
4
2
TA = –55°C
8
TA = 25°C
6
TA = 125°C
4
2
VEN = 4V
0
–55 –35 –15
0
5 25 45 65 85 105 125
TEMPERATURE (°C)
0
1
2
VS = ±5V
VIN = 0V
VS = ±5V
–5
–10
VIN = 0V
–10
VIN = 1.5V
–15
–20
VIN = –1.5V
–25
–30
–40
–55 –35 –15
5 25 45 65 85 105 125
TEMPERATURE (°C)
5
TA = 25°C
VS = ±5V
RL = 150Ω
TA = 125°C
TA = 25°C
–2
3
2
EN PIN VOLTAGE (V)
4
2
TA = 125°C
TA = 25°C
1
5
Output Voltage Swing
vs ILOAD (Output Low)
3
0
VS = ±5V
VIN = –2V
VVREF = 0V
–1
TA = 125°C
TA = 25°C
TA = –55°C
–2
–3
–4
TA = –55°C
–3 LOW SWING
–4
1
6555 G06
OUTPUT VOLTAGE (V)
–1
4
TA = 125°C
0
0
VS = ±5V
VIN = 2V
VVREF = 0V
VREF INPUT
CLAMPING
HIGH SWING
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1
TA = 25°C
–100
Output Voltage Swing
vs ILOAD (Output High)
TA = –55°C
2
TA = –55°C
–80
6555 G05
Maximum Output Voltage Swing
vs VREF Pin Voltage
3
TA = 125°C
–60
–140
5 25 45 65 85 105 125
TEMPERATURE (°C)
6555 G04
4
–40
–120
–35
–15
–55 –35 –15
4.0
VS = ±5V
VDGND = 0V
–20
EN PIN CURRENT (µA)
0
3.5
1.0 1.5 2.0 2.5 3.0
EN PIN VOLTAGE (V)
EN Pin Current vs EN Pin Voltage
0
–5
INPUT BIAS CURRENT (µA)
OFFSET VOLTAGE (mV)
0
5
0.5
6555 G03
Input Bias Current
vs Temperature
Input Referred Offset Voltage
vs Temperature
10
0
6555 G02
6555 G01
15
0
3 4 5 6 7 8 9 10 11 12
TOTAL SUPPLY VOLTAGE (V)
VREF INPUT
CLAMPING
TA = –55°C
–2 –1.5 –1 –0.5 0 0.5 1
VREF PIN VOLTAGE (V)
1.5
2
6555 G07
0
0
10 20 30 40 50 60 70 80 90 100
SOURCE CURRENT (mA)
6555 G08
–5
0
10 20 30 40 50 60 70 80 90 100
SINK CURRENT (mA)
6555 G09
6555f
4
LT6555
U W
TYPICAL PERFOR A CE CHARACTERISTICS
1000
VS = ±5V
TA = 25°C
100
en
in
10
0.01
0.1
1
FREQUENCY (kHz)
10
10
1
0.1
0.01
100
0.1
1
10
FREQUENCY (MHz)
100
Frequency Response
vs Output Amplitude
GAIN (dB)
VOUT = 200mVP-P
VOUT = 2VP-P
3
VOUT = 4VP-P
2
10
100
FREQUENCY (MHz)
12
6.05
IN1B
6.00
CL = 10pF
IN2A
6
CL = 0pF
4
2
IN2B
0
VS = ±5V
VOUT = 200mVP-P
RL = 150Ω
TA = 25°C
1
–2
–4
10
100
FREQUENCY (MHz)
–6
0.1
1000
1
10
100
FREQUENCY (MHz)
Harmonic Distortion vs Frequency
0
VS = ±5V
VIN = 1VP-P
–20 RL = 150Ω
TA = 25°C
–40
–40
AMPLITUDE (dB)
VS = ±5V
VOUT = 2VP-P
–20 RL = 150Ω
TA = 25°C
0
–10
–20
–30
–60
DRIVE IN A,
SELECT IN B
–80
DRIVE IN B,
SELECT IN A
–100
–100
–120
0.1
–120
0.1
1000
6555 G15
Crosstalk vs Frequency
Crosstalk vs Frequency
100
CL = 4.7pF
8
6555 G14
0
AMPLITUDE (dB)
10
VS = ±5V
VOUT = 2VP-P
RL = 150Ω
TA = 25°C
10
IN3B
IN3A
6555 G13
ALL
CHANNELS
DRIVEN
0.1
1
FREQUENCY (MHz)
Frequency Response with
Capacitive Loads
14
5.90
0.1
1000
WORST
ADJACENT
0.01
6555 G12
IN1A
1
–80
0
0.001
1000
18
6.10
5.95
–60
10
6.15
4
1
20
16
5
0
0.1
30
6.20
VS = ±5V
RL = 150Ω
TA = 25°C
6
–PSRR
40
GAIN (dB)
7
+PSRR
50
Gain Flatness vs Frequency
NORMALIZED GAIN (dB)
8
VS = ±5V
TA = 25°C
±PSRR
60
6555 G11
6555 G10
9
70
DISTORTION (dBc)
1
0.001
VS = ±5V
VIN = 0V
TA = 25°C
100
INPUT IMPEDANCE (kΩ)
INPUT NOISE VOLTAGE (nV/√Hz OR pA/√Hz)
1000
Input Referred PSRR
vs Frequency
Input Impedance vs Frequency
POWER SUPPLY REJECTION RATIO (dB)
Input Noise Spectral Density
VS = ±5V
VOUT = 2VP-P
RL = 150Ω
TA = 25°C
–40
–50
–60
HD3
–70
–80
HD2
–90
–100
–110
1
10
100
FREQUENCY (MHz)
1000
6555 G16
1
10
100
FREQUENCY (MHz)
1000
6555 G17
–120
0.01
0.1
1
10
FREQUENCY (MHz)
100
6555 G18
6555f
5
LT6555
U W
TYPICAL PERFOR A CE CHARACTERISTICS
1.8
0.4
0.2
0.1
0.01
0.1
1
10
FREQUENCY (MHz)
0.1
0
–0.1
100
1000
–0.4
0
2
4
6
8 10 12 14 16 18 20
TIME (ns)
2
OUTPUT (V)
OUTPUT (V)
35
1
0
–1
–2
–1.0
–3
–1.5
–4
8 10 12 14 16 18 20
TIME (ns)
0
2
4
6
10
0
1.5
–1.0 –0.5
0.5
1.0
GAIN ERROR—INDIVIDUAL CHANNEL (%)
6555 G24
INA = 0V TA = 25°C
INB = 0V
0.2
1.5
1.0
0.1
0.5
0
0
INB = 300MHz, 1VP-P SINE
VS = ±5V
RL = 150Ω TA = 25°C INA = 0V
–0.1
20
5
5
4
4
SEL A/B (V)
SEL A/B (V)
15
6555 G25
15
Channel Switching Transient
25
0
0
–1.5 –1.0 –0.5
1.5
0.5
1.0
GAIN MATCHING–BETWEEN CHANNELS (%)
20
2
0
0
10 20 30 40 50 60 70 80 90 100
TIME (ns)
6555 G26
–0.5
–1.0
OUT (V)
PERCENT OF UNITS (%)
VS = ±5V
RL = 150Ω
VS = ±5V
VOUT = ±2V
RL = 150Ω
TA = 25°C
5
25
0
–1.5
8 10 12 14 16 18 20
TIME (ns)
Channel Switching Transient
10
30
VS = ±5V
VOUT = ±2V
RL = 150Ω
TA = 25°C
OUT (V)
30
8 10 12 14 16 18 20
TIME (ns)
6555 G23
Gain Matching Distribution
35
6
5
6555 G22
40
4
Gain Error Distribution
40
VIN = 2.5VP-P
VS = ±5V
RL = 150Ω
TA = 25°C
3
–0.5
6
2
6555 G21
Large-Signal Transient Response
4
0
4
0
6555 G20
0.5
2
VIN = 0V TO 700mV
VS = ±5V
RL = 150Ω
TA = 25°C
–0.2
–0.4
VIN = 1VP-P
VS = ±5V
RL = 150Ω
TA = 25°C
0
0.6
0.4
0
–0.3
Large-Signal Transient Response
1.0
1.0
0.8
0.2
–0.2
VS = ±5V
RL = 150Ω
TA = 25°C
6555 G19
1.5
1.4
1.2
PERCENT OF UNITS (%)
ENABLED
VEN = O.4V
1.6
OUTPUT (V)
10
1
VIN = 200mVP-P
VS = ±5V
RL = 150Ω
TA = 25°C
0.3
DISABLED
VEN = 4V
OUTPUT (V)
OUTPUT IMPEDANCE (Ω)
1000
100
Video Amplitude Transient
Response
Small-Signal Transient Response
Output Impedance vs Frequency
–1.5
3
2
1
0
0
10 20 30 40 50 60 70 80 90 100
TIME (ns)
6555 G27
6555f
6
LT6555
U
U
U
PI FU CTIO S (GN24 Package)
IN1A (Pin 1): Channel 1 Input A. This pin has a nominal
impedance of 400kΩ and does not have any internal
termination resistor.
DGND (Pin 2): Digital Ground Reference for Enable Pin.
This pin is normally connected to ground.
IN2A (Pin 3): Channel 2 Input A. This pin has a nominal
impedance of 400kΩ and does not have any internal
termination resistor.
VREF (Pin 4): Voltage Reference for Input Clamping. This
is the tap to an internal voltage divider that defines midsupply. It is normally connected to ground in dual supply,
DC coupled applications.
IN3A (Pin 5): Channel 3 Input A. This pin has a nominal
impedance of 400kΩ and does not have any internal
termination resistor.
AGND1 (Pin 6): Analog Ground for the 360Ω Gain Resistor of Channel 1.
IN1B (Pin 7): Channel 1 Input B. This pin has a nominal
impedance of 400kΩ and does not have any internal
termination resistor.
AGND2 (Pin 8): Analog Ground for the 360Ω Gain Resistor of Channel 2.
IN2B (Pin 9): Channel 2 Input B. This pin has a nominal
impedance of 400kΩ and does not have any internal
termination resistor.
AGND3 (Pin 10): Analog Ground for the 360Ω Gain
Resistor of Channel 3.
IN3B (Pin 11): Channel 3 Input B. This pin has a nominal
impedance of 400kΩ and does not have any internal
termination resistor.
V – (Pin 12): Negative Supply Voltage. V – pins are not internally connected to each other and must all be connected
externally. Proper supply bypassing is necessary for best
performance. See the Applications Information section.
V + (Pins 13, 14, 24): Positive Supply Voltage. V+ pins are
not internally connected to each other and must all be
connected externally. Proper supply bypassing is necessary for best performance. See the Applications Information section.
V – (Pin 15): Negative Supply Voltage for Channel 3 Output
Stage. V – pins are not internally connected to each other
and must all be connected externally. Proper supply bypassing is necessary for best performance. See the Applications
Information section.
OUT3 (Pin 16): Channel 3 Output. It is twice the selected
channel 3 input and performs optimally with a 150Ω load
(a double terminated 75Ω cable).
V + (Pin 17): Positive Supply Voltage for Channels 2 and 3
Output Stages. V+ pins are not internally connected to each
other and must all be connected externally. Proper supply
bypassing is necessary for best performance. See the
Applications Information section.
OUT2 (Pin 18): Channel 2 Output. It is twice the selected
channel 2 input and performs optimally with a 150Ω load
(a double terminated 75Ω cable).
V – (Pin 19): Negative Supply Voltage for Channels 1 and
2 Output Stages. V – pins are not internally connected to each
other and must all be connected externally. Proper supply
bypassing is necessary for best performance. See the Applications Information section.
OUT1 (Pin 20): Channel 1 Output. It is twice the selected
channel 1 input and performs optimally with a 150Ω load
(a double terminated 75Ω cable).
V + (Pin 21): Positive Supply Voltage for Channel 1 Output
Stage. V+ pins are not internally connected to each other
and must all be connected externally. Proper supply
bypassing is necessary for best performance. See the
Applications Information section.
SEL (Pin 22): Select Pin. This high impedance pin selects
which set of inputs are sent to the output pins. When the
pin is pulled low, the A inputs are selected. When the pin
is pulled high, the B inputs are selected.
EN (Pin 23): Enable Control Pin. An internal pull-up
resistor of 46k defines the pin’s impedance and will turn
the part off if the pin is unconnected. When the pin is pulled
low, the amplifiers are enabled.
Exposed Pad (Pin 25, QFN Only): The Exposed Pad is V–
and must be soldered to the PCB. It is internally connected
to the QFN Pin 4, V–.
6555f
7
LT6555
U
W
U
U
APPLICATIO S I FOR ATIO
Power Supplies
The LT6555 is optimized for ±5V supplies but can be
operated on as little as ±2.25V or a single 4.5V supply and
as much as ±6V or a single 12V supply. Internally, each
supply is independent to improve channel isolation. Do
not leave any supply pins disconnected or the part may
not function correctly!
Enable/Shutdown
The LT6555 has a shutdown mode controlled by the EN
pin and referenced to the DGND pin. If the amplifier will
be enabled at all times, the EN pin can be connected
directly to DGND. If the enable function is desired, either
driving the pin above 2V or allowing the internal 46k pullup resistor to pull the EN pin to the top rail will disable the
amplifier. When disabled, the DC output impedance will
rise to approximately 360Ω through the internal feedback
and gain resistors. Supply current into the amplifier in the
disabled state will be:
V + – VEN V + – V –
IS =
+
46k
80k
It is important that the following constraints on the DGND,
EN and SEL pins are always followed:
V+ – VDGND ≥ 4.5V
VEN – VDGND ≤ 5.5V
VSEL – VDGND ≤ 8V
In dual supply cases where V+ is less than 4.5V, DGND
should be connected to a potential below ground, such as
V–. Since the EN and SEL pins are referenced to DGND,
they may need to be pulled below ground in those cases.
In single supply applications above 5.5V, an additional
resistor may be needed from the EN pin to DGND if the pin
is ever allowed to float. For example, on a 12V single
supply, a 33k resistor would protect the pin from floating
too high while still allowing the internal pull-up resistor to
disable the part.
On dual ±2.25V supplies, connecting the DGND pin to V–
is the only way of ensuring that V+ – VDGND ≥ 4.5V.
The DGND pin should not be pulled above the EN pin since
doing so will turn on an ESD protection diode. If the EN pin
voltage is forced a diode drop below the DGND pin, current
should be limited to 10mA or less.
The enable/disable times of the LT6555 are fast when
driven with a logic input. Turn on (from 50% EN input to
50% output) typically occurs in less than 50ns. Turn off is
slower, but is typically below 500ns.
Channel Select
The SEL pin uses the same internal threshold as the EN pin
and is also referenced to DGND. When the pin is logic low,
the channel A inputs are passed to the output. When the
pin is logic high, the channel B inputs are passed to the
output. The pin should not be floated but can be tied to
DGND to force the outputs to always be channel A or to V+
(when less than 8V) to force the outputs to always be
channel B.
Truth Table
SEL A/B
EN
OUT
0
0
2 × IN A
1
0
2 × IN B
X
1
OFF
Input Considerations
The LT6555 uses input clamps referenced to the VREF pin
to prevent damage to the input stage on the unselected
channel. Three transistors in series limit the input voltage
to within three diode drops (±) from VREF. VREF is nominally set to half of the sum of the supplies by the 40k
resistors. A simplified schematic is shown in Figure 1.
To improve clamping, the pin’s DC impedance should be
minimized by connecting the VREF pin directly to ground in
the symmetric dual supply case with a common mode
voltage of 0V. While loaded output swing limits the useful
input voltage range in that case, if the common mode
voltage is not centered at ground or the input voltage
exceeds plus or minus three diodes from ground, an
external resistor to either supply can be added to shift the
6555f
8
LT6555
U
W
U U
APPLICATIO S I FOR ATIO
V+
40k
IN
VREF
40k
V–
6555 F01
Figure 1. Simplified Schematic of VREF Pin and Input Clamping
VREF voltage to the desired level. The only way to cover the
full common mode voltage range of V– + 1V to V+ – 1V is
to shift VREF up or down. Note that on a single supply, the
unclamped input range limits the output low swing to 2V
(1V multiplied by the internal gain of 2).
The VREF pin can also be directly driven with a DC source.
Bypassing the VREF pin is not necessary.
The inputs can be driven beyond the point at which the
output clips so long as input currents are limited to less
than ±10mA. Continuing to drive the input beyond the
output limit can result in increased current drive and
slightly increased swing, but will also increase supply
current and may result in delays in transient response at
larger levels of overdrive.
Layout and Grounding
It is imperative that care is taken in PCB layout in order to
benefit from the very high speed and very low crosstalk of
the LT6555. Separate power and ground planes are highly
recommended and trace lengths should be kept as short
as possible. If input or output traces must be run over a
distance of several centimeters, they should use a controlled impedance with matching series and shunt resistances (nominally 75Ω) to maintain signal fidelity.
Series termination resistors should be placed as close to
the output pins as possible to minimize output capacitance. See the Typical Performance Characteristics section for a plot of frequency response with various output
capacitors—only 10pF of parasitic output capacitance
before the series termination resistor causes 6dB of
peaking in the frequency response!
Low ESL/ESR bypass capacitors should be placed as
close to the positive and negative supply pins as possible.
One 4700pF ceramic capacitor is recommended for both
V+ and V– supply busses. Additional 470pF ceramic capacitors with minimal trace length on each supply pin will
further improve AC and transient response as well as
channel isolation. For high current drive and large-signal
transient applications, additional 1µF to 10µF tantalums
should be added on each supply. The smallest value
capacitors should be placed closest to the package.
If the AGND pins are not connected to ground, they must
be carefully bypassed to maintain minimal impedance
over frequency. Although crosstalk will vary depending
upon board layout, a recommended starting point for
bypass capacitors would be 470pF as close as possible to
each AGND pin with a single 4700pF capacitor in parallel.
6555f
9
LT6555
U
W
U U
APPLICATIO S I FOR ATIO
To maintain the LT6555’s channel isolation, it is beneficial
to shield parallel input and parallel output traces using a
ground plane or power supply traces. Vias between topside
and backside metal may be required to maintain a low
inductance ground near the part where numerous traces
converge. See Figures 6 and 7 for photos of an optimized
layout.
Input Expansion
In applications with more than two inputs per channel,
multiple LT6555s can be connected by several different
methods. The simplest method is to connect the outputs
after the 75Ω series termination, as shown in Figure 2. The
compromise of this approach is that the internal gain
setting resistors cause a 435Ω shunt across the 75Ω cable
termination, resulting in increased gain error.
Figure 3 illustrates the loading effect of expanding the
number of inputs. The resultant gain error can be calculated by the following formula using n as the number of
LT6555s:
⎞
⎛ 435Ω
75Ω
⎟
⎜
Gain Error (dB) = 6dB + 20log ⎜ n – 1
⎟ dB
435Ω
⎜ 75 +
75Ω ⎟
⎠
⎝
n–1
For example, two LT6555s would result in a gain error of
–0.74dB per channel. Three LT6555s (i.e., six red inputs,
six green inputs and six blue inputs), would have a gain
error of –1.4dB.
1/3 LT6555 #1
IN1A
IN1A
75Ω
360Ω
OFF
⇒
360Ω
AV = 2
75Ω
IN1B
360Ω
75Ω
435
n–1
OFF
IN1B
R2
75Ω
360Ω
EN
n = NUMBER OF LT6555s
IN PARALLEL
LT6555 #1
1/3 LT6555 #2
IN1C
IN1C
75Ω
360Ω
CABLE
OFF
75Ω
360Ω
AV = +2
75Ω
OUT
IN1D
360Ω
ON
75Ω
IN1D
360Ω
EN
LT6555 #2
CHIP
SELECT
6555 F02
74HC04
Figure 2. Two LT6555s Build a 4-Input Router
.
.
.
n
6555 F03
Figure 3. Disabled Amplifiers Load the Cable
Termination with 435Ω Each
6555f
10
LT6555
U
W
U U
NUMBER OF DEVICES (n)
SERIES RT
2
63.9
3
56.2
4
49.9
Another approach that does not compromise gain accuracy is to connect the outputs directly together before the
series termination. In this case, there will be slightly
increased output glitching and supply current spiking
during the EN pin switching, but the additional output
loading will not increase the gain error, and the series
termination resistors remain at their ideal value for AC
response. See Figure 4 for a scope photo showing the
result of the outputs connected both before and after the
series terminations, and Figure 8 for a full schematic of a
4:1 RGB multiplexer with the output pins directly connected together. It is imperative that the output traces be
as short as possible before the series termination in order
to reduce capacitance and minimize AC peaking.
1.5
VS = ±5V
VIN(AMP1) = –0.5V
VIN(AMP2) = 0.5V
RL = 150Ω
1.0
0.5
0
SERIES 63.9Ω
AT EACH OUTPUT
–0.5
–1.0
OUTPUTS
DIRECTLY
CONNECTED
150
IS–
100
IS+
50
0
0
0.5
1
1.5 2 2.5
TIME (µs)
3
3.5
4
SUPPLY CURRENT (mA)
This systematic gain error can be significantly reduced by
lowering the value of the 75Ω series termination resistors.
The compromise of this approach is an increased dependence on the accuracy of the 75Ω shunt termination at the
receiving end of the line. A table of values for 1% series
termination resistors from n = 2 to n = 4 is shown below.
MULTIPLEXED OUTPUT (V)
APPLICATIO S I FOR ATIO
6555 F04
Figure 4. 4-Input Router Switching with Outputs Directly
Connected and with Outputs Connected After 63.9Ω
Series Termination
ESD Protection
The LT6555 has reverse-biased ESD protection diodes on
all pins. If any pins are forced a diode drop above the
positive supply or a diode drop below the negative supply,
large currents may flow through these diodes. If the
current is kept below 10mA, no damage to the devices will
occur.
U
TYPICAL APPLICATIO
RGB Multiplexer Demo Board
The DC858A Demo Board illustrates optimal routing,
bypassing and termination using the LT6555 as an
RGB video multiplexer. The schematic is shown in Figure 5. All inputs and outputs are routed to have a characteristic impedance of 75Ω and 75Ω input shunt and output
series terminations are connected as close to the part as
possible. The board is fabricated with four layers with
internal ground and power planes. For ideal operation, a
75Ω load termination should be connected at the output.
The LT6555’s gain of 2 will compensate for the resulting
divider between the series and load termination resistors.
Figures 6 and 7 show the topside and bottom side board
layout and placement.
6555f
11
LT6555
U
TYPICAL APPLICATIO
E1
EN
J1
50Ω BNC
1
EN
E4
SEL A/B
Z = 50
JP1
3 CONTROL 1
E2
DGND
2
R9
50Ω
OPT
R8
50Ω
OPT
2
EXT ENABLE
5 4 3 2 DGND
J8
50Ω BNC
1
SEL A/B
Z = 50
3 A
R7
B 1 20k
VCC
JP4
SEL
DGND
5 4 3 2
JP2
3 DGND 1
2
FLOAT AGND
3
IN1A
IN2A
IN3A
IN1B
IN2B
IN3B
BNC × 6
5 JP12
1 L1 Z = 75
4
3
2
5 JP13
1 L1 Z = 75
4
3
2
5 JP14
1 L1 Z = 75
4
3
2
5 JP5
1 L1 Z = 75
4
3
2
5 JP6
1 L1 Z = 75
4
3
2
5 JP7
1 L1 Z = 75
4
3
2
JP5
VREF
2
EXT
E5
VREF
C1
4700pF
GND
C2
470pF
C3
470pF
C10
4700pF
U1 LT6555CGN
1
24
V+
IN1A
DGND 2
3
VREF
4
5
6
7
8
9
10
11
R10
75Ω
J2
BANANA JACK
VCC
3.3V TO 5V
1
R11
75Ω
R12
75Ω
R4
75Ω
R5
75Ω
R6
75Ω
12
DGND
EN
IN2A
SEL
VREF
+
IN3A
AGND1
IN1B
AGND2
IN2B
OUT1
V–
OUT2
V
+
OUT3
22
R1
75Ω
20
19
R2
75Ω
18
17
R3
75Ω
16
15
IN3B
V+
14
V–
V+
13
C5
4700pF
SINGLE DUAL
2
1 JP3 3
SUPPLY
CC
L2
1
SEL
21
V–
AGND
C11
0.33µF
16V V
23 EN
AGND3
E3
AGND
J3
BANANA JACK
V
C4
10µF
16V
1206
C6
470pF
C7
470pF
C9
10µF
16V
1206
Z = 75
Z = 75
Z = 75
L2
L2
C8
0.33µF
BNC × 3
5
J9
4
3
2
J10 5
1
4
3
2
J11 5
1
4
3
2
OUT1
OUT2
OUT3
J4
BANANA JACK
VEE
–3.3V TO –5V
6555 F05
VEE
NOTE:
470pF BYPASS CAPACITORS LOCATED
AS CLOSE TO PINS AS POSSIBLE
Figure 5. Demo Board Schematic
Figure 6. Demo Board Topside
(IC Removed for Clarity)
Figure 7. Demo Board Bottom Side
6555f
12
V–
DGND
1k
46k
BIAS
V+
SELECT
TO OTHER
OUTPUT
STAGES
770Ω
SEL
100Ω
TO OTHER
INPUT STAGES
INA
V–
V+
VREF
V–
40k
40k V
REF
INB
100Ω
V–
V+
VREF
VREF
360Ω
360Ω
6555 SS
V–
360Ω AGND
360Ω
OUT
V+
W
W
SI PLIFIED SCHE ATIC
EN
V+
LT6555
(One channel shown)
6555f
13
LT6555
U
PACKAGE DESCRIPTIO
GN Package
24-Lead Plastic SSOP (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1641)
.337 – .344*
(8.560 – 8.738)
24 23 22 21 20 19 18 17 16 15 1413
.033
(0.838)
REF
.045 ±.005
.229 – .244
(5.817 – 6.198)
.254 MIN
.150 – .157**
(3.810 – 3.988)
.150 – .165
1
.0165 ± .0015
2 3
4
5 6
7
8
9 10 11 12
.0250 BSC
RECOMMENDED SOLDER PAD LAYOUT
.015 ± .004
× 45°
(0.38 ± 0.10)
.0075 – .0098
(0.19 – 0.25)
.0532 – .0688
(1.35 – 1.75)
.004 – .0098
(0.102 – 0.249)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
NOTE:
1. CONTROLLING DIMENSION: INCHES
INCHES
2. DIMENSIONS ARE IN
(MILLIMETERS)
.008 – .012
(0.203 – 0.305)
TYP
.0250
(0.635)
BSC
GN24 (SSOP) 0204
3. DRAWING NOT TO SCALE
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
6555f
14
LT6555
U
PACKAGE DESCRIPTIO
UF Package
24-Lead Plastic QFN (4mm × 4mm)
(Reference LTC DWG # 05-08-1697)
0.70 ±0.05
4.50 ± 0.05
2.45 ± 0.05
3.10 ± 0.05 (4 SIDES)
PACKAGE OUTLINE
0.25 ±0.05
0.50 BSC
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
4.00 ± 0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
0.75 ± 0.05
R = 0.115
TYP
PIN 1 NOTCH
R = 0.20 TYP OR
0.35 × 45° CHAMFER
23 24
0.40 ± 0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
2.45 ± 0.10
(4-SIDES)
(UF24) QFN 0105
0.200 REF
0.00 – 0.05
0.25 ± 0.05
0.50 BSC
NOTE:
1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
6555f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT6555
U
TYPICAL APPLICATIO
RED 1
GREEN 1
BLUE 1
V+
LT6555 #1
75Ω
IN1A
IN1B
5V
OUT1
×2
75Ω
75Ω
RED 2
GREEN 2
BLUE 2
IN2A
IN2B
OUT2
×2
75Ω
75Ω
IN3A
IN3B
75Ω
OUT3
×2
AGND
DGND
SEL
75Ω
VREF
EN
ROUT
75Ω
V–
–2V
5V
RED 3
GREEN 3
BLUE 3
IN1A
IN1B
GOUT
75Ω
V+
LT6555 #2
75Ω
75Ω
OUT1
×2
75Ω
BOUT
75Ω
75Ω
75Ω
RED 4
GREEN 4
BLUE 4
IN2A
IN2B
OUT2
×2
75Ω
75Ω
IN3A
IN3B
75Ω
OUT3
×2
AGND
DGND
SEL
VREF
EN
SEL0
V–
NC75Z14
SEL1 SEL0 OUTPUT
0
0
1
0
1
2
1
0
3
1
1
4
SEL1
6555 F08
–2V
Figure 8. 4:1 RGB Multiplexer
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1203
150MHz Single 2:1 Multiplexer
Single SPDT Video Switch
LT1399
300MHz Triple Current Feedback Amplifier
0.1dB Gain Flatness to 150MHz, Shutdown
LT1675
250MHz Triple RGB Multiplexer
100MHz Pixel Switching, 1100V/µs Slew Rate, 16-Lead SSOP
LT6550/LT6551
3.3V Triple and Quad Video Buffers
110MHz Gain of 2 Buffers in MS Package
LT6553
650MHz Gain of 2 Triple Video Amplifier
Performance Similar to the LT6555 with One Set of Inputs, 16-Lead SSOP
LT6554
650MHz Gain of 1 Triple Video Amplifier
Same Pinout as the LT6553 but Optimized for High Impedance Loads
6555f
16
Linear Technology Corporation
LT/TP 0405 500 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2005