ICHAUS IC-WKN 15 v cw laser diode driver Datasheet

iC-WKN
15 V CW LASER DIODE DRIVER
Rev B1, Page 1/9
FEATURES
APPLICATIONS
♦
♦
♦
♦
♦
♦ Blue laser diodes
♦ LD modules
♦
♦
♦
♦
♦
♦
♦
CW operation up to 300 mA from 2.4 to 15 V supply voltage
Rapid soft start after power-on typical within 70 µs
Optimised for N-type laser diodes
Simple output power adjustment via an external resistor (APC)
Power control loop accuracy better than 1.5 % with changes in
temperature, supply voltage and load current
Integrated reverse polarity protection for the iC and laser diode
Strong suppression of transients with very small external
capacitors; integrated flyback path
Permanent shutdown with excessive temperature and
overcurrent (i.e. if the laser diode is damaged or the feedback
current path fails)
Two feedback inputs permit all current LD types to be used
(N/P/M configurations)
Modulation via the feedback inputs is possible
Wide monitor current range from 2.5 µA to 6.25 mA
Pin compatible to iC-WK and iC-WKL (SO8 package)
PACKAGES
DFN10
4 mm x 4 mm
(on request)
SO8tp
BLOCK DIAGRAM
+2.4..+15 V
6
VCC
LDA
7
CVCC
CLDA
..47 nF..
..1 uF..
TRANSIENT
PROTECTION
−
iC−WKN
1
MDK
4
MDA
5
MD
LD
+
VREF
0.5 V
CI
D
LDK
2
8
NQ
R
RM
CI
0.08..200 k Ω
OVERCURRENT
OVERTEMP.
1
GND
..100 nF..
FEEDBACK MON.
GND
AGND
CM
47 pF
3
suitable laser diode configurations: N, P, M
MD
MD
Copyright © 2004 iC-Haus
LD
LD
LD
MD
http://www.ichaus.com
iC-WKN
15 V CW LASER DIODE DRIVER
Rev B1, Page 2/9
DESCRIPTION
iC-WKN is a driver for laser diodes in continuous
wave operation with laser currents of up to 300 mA,
which requires only four external components. The
wide power supply range of up to 15 V allows for operation of blue laser diodes.
The iC includes integrated circuitry protecting against
destruction by ESD, excessive temperature and overcurrent plus a soft start of the regulator to protect the
laser diode when the power supply is switched on.
The iC also filters the laser diode power supply for
transients.
The regulator is adapted to the laser diode by an external resistor at MDA. The monitor current acts as
a reference and is regulated independent of the influence of temperature and supply voltage (range:
2.5 µA to 6.25 mA). The capacitor at CI determines
the control time constants and start-up time.
A second monitor input, pin MDK, allows the driver to
be used for other types of laser diode configuration;
alternatively, it can be used as an analog modulation
input (DC to a few kHz).
In the event of failure, such as overcurrent in the laser
path due to a lack of feedback, for example, a quick
power lockout is activated. The shutdown persists
until power is reapplied, permitting a restart. The
strain on power packs and batteries is relieved and
the laser class is retained even in the event of a disturbance.
iC-WKN offers additional protection by means of
spike detection at pin MDA. Should spikes or oscillation occur at pin MDA the power lockout is activated
after a certain time-out.
iC-WKN
15 V CW LASER DIODE DRIVER
Rev B1, Page 3/9
PACKAGES SO8tp, DFN10 4 mm x 4 mm to JEDEC standard
PIN CONFIGURATION SO8tp
(top view)
PIN FUNCTIONS
No. Name Function
1
8
2
7
LDA
1
2
3
4
VCC
5 MDA
MDA
6 VCC
7 LDA
8 LDK
LDK
GND
CI
4
WKN
code...
...
3
AGND
6
GND
CI
AGND
MDK
5
MDK
Ground
Capacitance for Power Control
Reference Ground for CI, RM
Monitor Input 2
(MD Cathode, modulation)
APC Setup, Monitor Input 1
(MD Anode)
+2.4...+15 V Supply Voltage
Laser Supply (LD Anode)
Driver Output (LD Cathode)
The Thermal Pad is to be connected to a Ground Plane on the PCB. Do not short-circuit pins AGND and
GND, for this may deteriorate the precision of the regulator and interfere with the soft-start!
6
7
8
9
10
PIN CONFIGURATION DFN10 4 mm x 4 mm
(top view)
iC−WKN
5
4
3
...yyww
2
1
2
3
4
GND
CI
AGND
MDK
5 n.c.
6 MDA
...
1
PIN FUNCTIONS
No. Name Function
7
8
9
10
n.c.
VCC
LDA
LDK
Ground
Capacitance for Power Control
Reference Ground for CI, RM
Monitor Input 2
(MD Cathode, modulation)
APC Setup, Monitor Input 1
(MD Anode)
+2.4...+15 V Supply Voltage
Laser Supply (LD Anode)
Driver Output (LD Cathode)
The Thermal Pad is to be connected to a Ground Plane on the PCB. Do not short-circuit pins AGND and
GND, for this may deteriorate the precision of the regulator and interfere with the soft-start!
iC-WKN
15 V CW LASER DIODE DRIVER
Rev B1, Page 4/9
ABSOLUTE MAXIMUM RATINGS
Beyond these values damage may occur; device operation is not guaranteed.
ItemNo.
Symbol
Parameter
Conditions
Fig.
Unit
Min.
Max.
G001 VCC
Voltage at VCC
-6
16
V
G002 I(VCC)
Current in VCC
-10
900
mA
G003 I(CI)
Current in CI
-10
10
mA
G004 I(LDA)
Current in LDA
-900
10
mA
G005 I(LDK)
Current in LDK
-10
900
mA
G006 I(MDA)
Current in MDA
-10
10
mA
G007 I(MDK)
Current in MDK
-10
10
mA
G008 I(AGMD)
Current in AGND
-10
10
mA
G009 I(GND)
Current in GND
-900
10
mA
G010 Vd()
ESD Susceptibility at all pins
2
kV
G011 Tj
Operating Junction Temperature
-40
150
°C
G012 Tj
Storage Temperature Range
-40
150
°C
MIL-STD-883, Method 3015, HBM
100 pF discharged through 1.5 kΩ
THERMAL DATA
Operating Conditions: VCC = 2.4...15 V
ItemNo.
T01
T02
Symbol
Parameter
Conditions
Fig.
Unit
Min.
Ta
Rthja
Operating Ambient Temperature Range
Thermal Resistance Chip/Ambient
Typ.
-40
soldered to PCB;
no additional cooling areas
therm. pad soldered to approx. 2 cm²
cooling area
All voltages are referenced to ground unless otherwise noted.
All currents into the device pins are positive; all currents out of the device pins are negative.
30
Max.
85
°C
170
50
k/W
k/W
iC-WKN
15 V CW LASER DIODE DRIVER
Rev B1, Page 5/9
ELECTRICAL CHARACTERISTIC
Operating Conditions: VCC = 2.4...15 V, RM = 80 Ω...200 kΩ, Tj = -40...125 °C unless otherwise noted
ItemNo.
Symbol
Parameter
Conditions
Tj
°C
Unit
Fig.
Min.
Typ.
Max.
Total Device
001
VCC
Permissible Supply Voltage
002
I(LDK)m
Permissible Laser Drive Current
003
Idc(VCC)
Supply Current without load path closed control loop, I(MDK) = 0,
I(LDK) = 290 mA
004
Ioff(VCC)
Supply Current on Reset
005
006
Ir(VCC)
Reverse Supply Current
RM = 50 kΩ, VCC = -6 V
ton()
Turn-on Delay
VCC: 0 → 5 V to 95 % I(LDK),
I(LDK) = I(LDK)m;
CI = 47 nF
CI = 100 nF
power control range
2.4
15
V
10
300
mA
10
20
mA
2.4
5
mA
-6
-3
mA
70
150
µs
µs
007
Vc()hi
Clamp Voltage hi at VCC, LDA
I()= 10 mA, other pins open
16
24
V
008
Vc()hi
Clamp Voltage hi at LDK
V() < VCC + 1 V; I() = 10 mA,
other pins open
16
24
V
009
Vc()hi
Clamp Voltage hi at MDK vs. LDA I() = 10 mA, other pins open
8
11
V
010
Vc()hi
Clamp Voltage hi at MDA, CI
I() = 10 mA, other pins open
1.1
4
V
011
Vc()lo
Clamp Voltage lo at VCC, LDA,
MDK, MDA, CI
I() = -10 mA, other pins open
-9
V
Reference and Monitor Inputs MDA, MDK, AGND
101
V(MDA)
Reference Voltage at MDA
closed control loop,
V(LDK) > Vs(LDK)
102
dV(MDA)
Reference Voltage Temperature
Drift at MDA
see 101
103
Ierr(MDA)
Input Current in MDA
closed control loop, I(MDK) = 0,
I(LDK) = 10...290 mA
104
dI(MDA)
Input Current Temperature Drift in see 103
MDA
105
APCerr
Control Error
RM = 10 kΩ, Tj = 0...80 °C
RM = 10 kΩ, Tj = -40...125 °C
106
dI(RM)
Supply Voltage Suppression
V(VCC): 2.4 → 15 V,
I(LDK) = 290 mA
-1.5
107
Rgnd()
Resistor AGND-GND
108
Vf(MDK)
Voltage at MDK
Vf() = V(LDA) - V(MDK),
I(MDK) = 1 µA...1 mA
0.46
109
CR()
Current Ratio I(MDA) / I(MDK)
I(MDK) = 1 µA...1 mA
I(MDK) = 1..6 mA
0.98
0.95
1.02
1.05
110
TC()
Current Ratio Temperature
Coefficient I(MDA) / I(MDK)
I(MDK) = 1 µA...1 mA
I(MDK) = 1...6 mA
-0.005
-0.025
0.005
0.025
%/°C
%/°C
350
700
mV
mV
Laser Driver LDA, LDK
201 Vs(LDK)
Saturation Voltage at LDK
480
520
mV
120
µV/°C
-100
100
nA
-1
1
nA/°C
0.3
1
%
%
1.5
%
3
Ω
2
V
I(LDK) = 40 mA
I(LDK) = 290 mA
500
202
dI(LD)
Load Balancing Error
I(LD) = 20 mA,
I(LDK): 20 mA → 290 mA
-1.5
1.5
%
203
It(LDK)
Overcurrent Threshold in LDK
V(LDK) = 2...5.5 V
300
700
mA
204
It(LDK)m
Maximum Overcurrent Threshold
in LDK
1.2
A
205
toff()
Overcurrent Reset Delay
lack of feedback:
I(MD) = 0 to I(LDK) = It(LDK);
CI = 47 nF
CI = 100 nF
85
170
µs
µs
1.3
V
1.3
Ω
2
V
206
Vf()
Flyback Diode Forward Voltage
LDK-LDA
I(LDK) < 290 mA
207
Rvcc()
Transient Protection Resistor
VCC to LDA
208
Vt(MDA)
Shutdown Threshold at MDA
t > 1 µs
0.7
iC-WKN
15 V CW LASER DIODE DRIVER
Rev B1, Page 6/9
ELECTRICAL CHARACTERISTIC
Operating Conditions: VCC = 2.4...15 V, RM = 80 Ω...200 kΩ, Tj = -40...125 °C unless otherwise noted
ItemNo.
Symbol
Parameter
Control Release Flip-Flop
401 VCCen
Set Threshold for Enable
Flip-Flop
402
Toff
Overtemperature Shutdown
Conditions
Tj
°C
-40
27
125
Unit
Fig.
Min.
Typ.
Max.
0.6
1.2
1.0
0.6
1.9
1.9
1.7
1.2
V
V
V
V
140
165
°C
iC-WKN
15 V CW LASER DIODE DRIVER
Rev B1, Page 7/9
SAFETY PRECAUTIONS
Laser light can damage the human eye and the
eyes of animals. Do not look at any laser light directly or through any optical lens. When handling a
laser diode, do not look directly at the light generated
by it. Wear appropriate safety glasses to prevent light
from entering the eye even by reflection.
FUNCTION DESCRIPTION
Turn-on behaviour
After switching the supply voltage on, the output stage
remains disabled until the internal enabling flip-flop is
set by a sufficiently high voltage at LDA.
5V
4V
3V
tor determining the lowest possible supply voltage.
If the voltage drops below this value, the output driver
is forcibly saturated and the laser current decreases.
iC-WKN simultaneously discharges the control capacitor CI so that no excessive laser diode currents occur
when the supply voltage rises again.
2V
1V
0
V(VCC)
5V
4V
5V
4V
3V
2V
Phase I
Phase II
3V
Phase III
2V
1V
1V
0
V(LDA)
0
V(VCC)
400 mV
5V
300 mV
4V
200 mV
3V
2V
100 mV
1V
V(MDA)
0
V(LDA)
1V
400 mV
300 mV
500 mV
200 mV
0
V(CI)
100 mV
V(MDA)
60 m
40 m
1V
20 m
0
I(LDK)
Phase IV
500 mV
0
10 us
20 us
Time
30 us
40 us
50 us
Phase V
0
V(CI)
60 m
Figure 1: Turn-on behaviour
40 m
20 m
0
I(LDK)
A quick soft-start follows during phase I; the control
capacitor CI is charged at an accelerated rate until the
voltage at pin MDA reaches 1/3 of its nominal value.
With V (MDA) > 1/3V (MDA)nom phase II starts, the
controlled start-up. The transition to CW operation
(phase III) is gradual and primarily determined by the
values of CI and RM. CI is properly dimensioned when
the voltage overshoot at MDA is at a minimum.
Turn-off behaviour
iC-WKN works without a fixed undervoltage lockout,
thus the laser diode forward voltage is the prime fac-
100 us
110 us
120 us
Time
130 us
140 us
150 us
160 us
Figure 2: Turn-off behaviour
Disruptions in operation
The power control is shut down with excessive driver
temperature or when the laser current reaches the
overcurrent shutdown threshold, for example when the
feedback is interrupted. If the monitor diode or the
bias resistor RM fail, the device is shut down in less
than 250 µs, provided that the supply voltage applied
is high enough. When modulating the laser current via
pin MDK, excessive voltage occurring at pin MDA also
may cause a shutdown.
iC-WKN
15 V CW LASER DIODE DRIVER
Rev B1, Page 8/9
APPLICATION NOTES
Setting the output power
The output power is simply set by RM = V(MDA) /
I(MD); with V(MDA) = Item-No. 101 and I(MD) = monitor current of the laser diode at the desired operating
point. RM should be combined from a fixed resistor
(max. output power) and a trimmer (calibration).
Further application notes on the iC-WK family (iC-WK,
iC-WKL, iC-WKN) and the data sheet of the demo
board are available as separate documents.
This specification is for a newly developed product. iC-Haus therefore reserves the right to change or update, without notice, any information contained herein,
design and specification; and to discontinue or limit production or distribution of any product versions. Please contact iC-Haus to ascertain the current data.
Copying – even as an excerpt – is only permitted with iC-Haus approval in writing and precise reference to source.
iC-Haus does not warrant the accuracy, completeness or timeliness of the specification on this site and does not assume liability for any errors or omissions
in the materials. The data specified is intended solely for the purpose of product description. No representations or warranties, either express or implied, of
merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to information/specification or the products to which
information refers and no guarantee with respect to compliance to the intended use is given. In particular, this also applies to the stated possible applications or
areas of applications of the product.
iC-Haus conveys no patent, copyright, mask work right or other trade mark right to this product. iC-Haus assumes no liability for any patent and/or other trade
mark rights of a third party resulting from processing or handling of the product and/or any other use of the product.
iC-WKN
15 V CW LASER DIODE DRIVER
Rev B1, Page 9/9
ORDERING INFORMATION
Type
Package
Order Designation
iC-WKN
SO8tp
DFN10 4 mm x 4 mm
iC-WKN SO8
iC-WKN DFN10
Demo Board
WKN4D DEMO
For information about prices, terms of delivery, other packaging options etc. please contact:
iC-Haus GmbH
Am Kuemmerling 18
D-55294 Bodenheim
GERMANY
Tel +49 (61 35) 92 92-0
Fax +49 (61 35) 92 92-192
Web: http://www.ichaus.com
E-Mail: [email protected]
Similar pages