MD100VHI Series Miniature 1W, SIP, Very High Isolation DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 1W Output Power Input Parameter Conditions • Miniature SIP Case • 5,200 VDC Isolation Input Voltage Range • Single & Dual Outputs • >2.0 MHour MTBF Input Filter • -40°C to +85°C Operation Output • Industry Standard Pin-Out Min. Typ. Max. 5 VDC Input 4.50 5.0 5.50 Units 12 VDC Input 10.80 12.0 13.20 15 VDC Input 13.50 15.0 16.50 24 VDC Input 21.60 24.0 26.40 Typ. Max. ±5.0 % Dual Output, Balanced Loads ±0.1 ±1.0 % For VIN Change of 1% ±1.2 VDC Internal Capacitor Parameter Conditions Min. Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation, See Note 1 Units % See Model Selection Guide Ripple & Noise (20 MHz), See Note 2 Temperature Coefficient ±0.01 Output Short Circuit 100 mV P - P ±0.02 %/°C Max. Units Momentary (0.5 Sec.) General Parameter Conditions Isolation Voltage Min. 60 Seconds Isolation Resistance 500 VDC Isolation Capacitance VDC 10 100 kHz, 1V Common Mode Transient Immunity Typ. 5,200 G 7 pF 15 Switching Frequency kV/µS 100 kHz Environmental Parameter Conditions Operating Temperature Range Ambient Operating Temperature Range Case Storage Temperature Range Min. Typ. Max. Units -40 +25 +85 °C -55 Cooling, See Note 3 +100 °C +125 °C 95 % Free Air Convection Humidity RH, Non-condensing Physical Case Size See Mechanical Drawing (Page 2) Case Material Non-Conductive Black Plastic (UL-94V0) MicroPower Direct Weight 292 Page Street Suite D Stoughton, MA 02072 USA Reliability Specifications 0.076 Oz (2.4g) T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Parameter Conditions MTBF Min. MIL HDBK 217F, 25°C, Gnd Benign Typ. Max. 2.0 Units MHours Absolute Maximum Ratings Conditions Min. 5 VDC Input Input Voltage Surge (1 Sec) Lead Temperature Typ. Max. -0.7 9.0 12 VDC Input -0.7 18.0 15 VDC Input -0.7 20.0 24 VDC Input -0.7 30.0 1.5 mm From Case For 10 Sec 260 Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com Units VDC °C www.micropowerdirect.com Model Selection Guide Input Model Number MD105S-03VHI MD105S-05VHI MD105S-09VHI MD105S-12VHI MD105S-15VHI MD105D-05VHI MD105D-09VHI MD105D-12VHI MD105D-15VHI MD112S-03VHI MD112S-05VHI MD112S-09VHI MD112S-12VHI MD112S-15VHI MD112D-05VHI MD112D-09VHI MD112D-12VHI MD112D-15VHI MD115S-03VHI MD115S-05VHI MD115S-09VHI MD115S-12VHI MD115S-15VHI MD115D-05VHI MD115D-09VHI MD115D-12VHI MD115D-15VHI MD124S-03VHI MD124S-05VHI MD124S-09VHI MD124S-12VHI MD124S-15VHI MD124D-05VHI MD124D-09VHI MD124D-12VHI MD124D-15VHI Voltage (VDC) Nominal 5 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 12 15 15 15 15 15 15 15 15 15 24 24 24 24 24 24 24 24 24 Output Current (mA) Voltage Current Range Full-Load No-Load (VDC) (mA, Max) 4.5 - 5.5 286 35 3.3 303 4.5 - 5.5 286 35 5.0 200 4.5 - 5.5 266 35 9.0 111 4.5 - 5.5 261 35 12.0 84 4.5 - 5.5 254 35 15.0 66 4.5 - 5.5 282 35 ±5.0 ±100 4.5 - 5.5 269 35 ±9.0 ±56 4.5 - 5.5 262 35 ±12.0 ±42 4.5 - 5.5 254 35 ±15.0 ±33 10.8 - 13.2 117 17 3.3 303 10.8 - 13.2 117 17 5.0 200 10.8 - 13.2 110 17 9.0 111 10.8 - 13.2 108 17 12.0 84 10.8 - 13.2 104 17 15.0 66 10.8 - 13.2 116 17 ±5.0 ±100 10.8 - 13.2 111 17 ±9.0 ±56 10.8 - 13.2 108 17 ±12.0 ±42 10.8 - 13.2 104 17 ±15.0 ±33 13.5 - 16.5 95 16 3.3 303 13.5 - 16.5 95 16 5.0 200 13.5 - 16.5 89 16 9.0 111 13.5 - 16.5 90 16 12.0 84 13.5 - 16.5 84 16 15.0 66 13.5 - 16.5 94 16 ±5.0 ±100 13.5 - 16.5 90 16 ±9.0 ±56 13.5 - 16.5 86 16 ±12.0 ±42 13.5 - 16.5 84 16 ±15.0 ±33 21.6 - 26.4 60 12 3.3 303 21.6 - 26.4 60 12 5.0 200 21.6 - 26.4 56 12 9.0 111 21.6 - 26.4 53 12 12.0 84 21.6 - 26.4 52 12 15.0 66 21.6 - 26.4 59 12 ±5.0 ±100 21.6 - 26.4 56 12 ±9.0 ±56 21.6 - 26.4 55 12 ±12.0 ±42 21.6 - 26.4 53 12 ±15.0 ±33 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple & noise, it is recommended that an external ceramic capacitor (0.33 µF typ.) be placed from the +VOUT to the -VOUT pins for single output units and from each output to common for dual output models. 3. Free air convection is typically 20 LFM. The units should not be operated in still air (0 LFM). 4. Operation at no load will not damage these units, however, they may not meet all specifications. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Output Load Fuse Rating Capacitive Efficiency Regulation Slow-Blow Load (%, Typ) (% Typ) (mA) (µF Max) 20.0 15.0 10.0 10.0 10.0 15.0 10.0 10.0 10.0 20.0 15.0 10.0 10.0 10.0 15.0 10.0 10.0 10.0 20.0 15.0 10.0 10.0 10.0 15.0 10.0 10.0 10.0 20.0 15.0 10.0 10.0 10.0 15.0 10.0 10.0 10.0 1,000 470 470 220 220 ±220 ±220 ±100 ±100 1,000 470 470 220 220 ±220 ±220 ±100 ±100 1,000 470 470 220 220 ±220 ±220 ±100 ±100 1,000 470 470 220 220 ±220 ±220 ±100 ±100 70 70 75 77 78 71 75 77 78 71 71 76 78 79 72 76 78 79 70 70 75 75 79 71 75 78 79 70 70 75 78 80 71 75 77 78 600 600 600 600 600 600 600 600 600 250 250 250 250 250 250 250 250 250 200 200 200 200 200 200 200 200 200 125 125 125 125 125 125 125 125 125 Mechanical Dimensions Derating Curve Pin Connections Pin 1 2 5 Single +VIN -VIN -VOUT Dual +VIN -VIN -VOUT Pin 6 7 Single No Pin +VOUT Dual Common +VOUT MicroPower Direct Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the unit We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]