LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 Single Supply Quad Comparators www.onsemi.com These comparators are designed for use in level detection, low−level sensing and memory applications in consumer, automotive, and industrial electronic applications. SOIC−14 D SUFFIX CASE 751A 14 Features • • • • • • • • • • • 1 Single Supply Operation: 3.0 V to 36 V Split Supply Operation: ±1.5 V to ±18 V Low Input Bias Current: 25 nA (Typ) Low Input Offset Current: ±5.0 nA (Typ) Low Input Offset Voltage Input Common Mode Voltage Range to GND Low Output Saturation Voltage: 130 mV (Typ) @ 4.0 mA TTL and CMOS Compatible ESD Clamps on the Inputs Increase Reliability without Affecting Device Operation NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant PDIP−14 N, P SUFFIX CASE 646 14 1 TSSOP−14 DTB SUFFIX CASE 948G 14 1 PIN CONNECTIONS Output 2 1 14 Output 3 Output 1 2 13 Output 4 VCC 3 12 GND - Input 1 4 11 + Input 4 10 - Input 4 9 + Input 3 8 - Input 3 + Input 1 5 - Input 2 6 + Input 2 7 * 1 ) 4 *2 ) 3 ) * ) * (Top View) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page 8 of this data sheet. © Semiconductor Components Industries, LLC, 2016 October, 2016 − Rev. 23 1 Publication Order Number: LM339/D LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 MAXIMUM RATINGS Rating Symbol Power Supply Voltage VCC LM239/LM339, E/LM2901, E, V MC3302 Input Differential Voltage Range Value Vdc +36 or ±18 +30 or ±15 VIDR Vdc 36 30 LM239/LM339, E/LM2901, E, V MC3302 Input Common Mode Voltage Range VICMR −0.3 to VCC Output Short Circuit to Ground (Note 1) ISC Continuous Power Dissipation @ TA = 25°C Plastic Package Derate above 25°C PD Junction Temperature Operating Ambient Temperature Range Vdc 1/RqJA 1.0 8.0 W mW/°C TJ 150 °C °C TA −25 to +85 −40 to +85 −40 to +105 −40 to +125 0 to +70 LM239 MC3302 LM2901, LM2901E LM2901V, NCV2901 LM339, LM339E Storage Temperature Range Unit Tstg −65 to +150 °C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC. Output short circuits to VCC can cause excessive heating and eventual destruction. ESD RATINGS Rating ESD Protection at any Pin (Human Body Model − HBM, Machine Model − MM) NCV2901 LM339E, LM2901E LM339DG/DR2G, LM2901DG/DR2G All Other Devices VCC - Input + Input GND NOTE: Diagram shown is for 1 comparator. Figure 1. Circuit Schematic www.onsemi.com 2 HBM MM Unit 2000 1500 250 1500 200 200 100 200 V V V V Output LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 ELECTRICAL CHARACTERISTICS (VCC = +5.0 Vdc, TA = +25°C, unless otherwise noted) LM239/339/339E LM2901/2901E/2901V /NCV2901 MC3302 Symbol Min Typ Max Min Typ Max Min Typ Max Unit Input Offset Voltage (Note 3) VIO − ±2.0 ±5.0 − ±2.0 ±7.0 − ±3.0 ±20 mVdc Input Bias Current (Notes 3, 4) IIB − 25 250 − 25 250 − 25 500 nA IIO − ±5.0 ±50 − ±5.0 ±50 − ±3.0 ±100 nA VICMR 0 − VCC −1.5 0 − VCC −1.5 0 − VCC −1.5 V RL = ∞ (For All Comparators) − 0.8 2.0 − 0.8 2.0 − 0.8 2.0 RL = ∞, VCC = 30 Vdc − 1.0 2.5 − 1.0 2.5 − 1.0 2.5 AVOL 50 200 − 25 100 − 25 100 − V/mV − − 300 − − 300 − − 300 − ns − − 1.3 − − 1.3 − − 1.3 − ms ISink 6.0 16 − 6.0 16 − 6.0 16 − mA Vsat − 130 400 − 130 400 − 130 500 mV IOL − 0.1 − − 0.1 − − 0.1 − nA Characteristic (Output in Analog Range) Input Offset Current (Note 3) Input Common Mode Voltage Range Supply Current Voltage Gain ICC mA RL ≥ 15 kW, VCC = 15 Vdc Large Signal Response Time VI = TTL Logic Swing, Vref = 1.4 Vdc, VRL = 5.0 Vdc, RL = 5.1 kW Response Time (Note 5) VRL = 5.0 Vdc, RL = 5.1 kW Output Sink Current VI (−) ≥ +1.0 Vdc, VI(+) = 0, VO ≤ 1.5 Vdc Saturation Voltage VI(−) ≥ +1.0 Vdc, VI(+) = 0, Isink ≤ 4.0 mA Output Leakage Current VI(+) ≥ +1.0 Vdc, VI(−) = 0, VO = +5.0 Vdc Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. 2. (LM239) Tlow = −25°C, Thigh = +85° (LM339, LM339E) Tlow = 0°C, Thigh = +70°C (MC3302) Tlow = −40°C, Thigh = +85°C (LM2901), LM2901E Tlow = −40°C, Thigh = +105° (LM2901V & NCV2901) Tlow = −40°C, Thigh = +125°C NCV2901 is qualified for automotive use. 3. At the output switch point, VO ] 1.4 Vdc, RS ≤ 100 W 5.0 Vdc ≤ VCC ≤ 30 Vdc, with the inputs over the full common mode range (0 Vdc to VCC −1.5 Vdc). 4. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state. 5. The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical. www.onsemi.com 3 LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 PERFORMANCE CHARACTERISTICS (VCC = +5.0 Vdc, TA = Tlow to Thigh [Note 6]) LM2901/2901E/2901V /NCV2901 LM239/339/339E MC3302 Symbol Min Typ Max Min Typ Max Min Typ Max Unit Input Offset Voltage (Note 7) VIO − − ±9.0 − − ±15 − − ±40 mVdc Input Bias Current (Notes 7, 8) IIB − − 400 − − 500 − − 1000 nA IIO − − ±150 − − ±200 − − ±300 nA VICMR 0 − VCC −2.0 0 − VCC −2.0 0 − VCC −2.0 V Vsat − − 700 − − 700 − − 700 mV IOL − − 1.0 − − 1.0 − − 1.0 mA VID − − VCC − − VCC − − VCC Vdc Characteristic (Output in Analog Range) Input Offset Current (Note 7) Input Common Mode Voltage Range Saturation Voltage VI(−) ≥ +1.0 Vdc, VI(+) = 0, Isink ≤ 4.0 mA Output Leakage Current VI(+) ≥ +1.0 Vdc, VI(−) = 0, VO = 30 Vdc Differential Input Voltage All VI ≥ 0 Vdc 6. (LM239) Tlow = −25°C, Thigh = +85° (LM339, LM339E) Tlow = 0°C, Thigh = +70°C (MC3302) Tlow = −40°C, Thigh = +85°C (LM2901, LM2901E) Tlow = −40°C, Thigh = +105° (LM2901V & NCV2901) Tlow = −40°C, Thigh = +125°C NCV2901 is qualified for automotive use. 7. At the output switch point, VO ] 1.4 Vdc, RS ≤ 100 W 5.0 Vdc ≤ VCC ≤ 30 Vdc, with the inputs over the full common mode range (0 Vdc to VCC −1.5 Vdc). 8. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state. 9. The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical. + VCC + VCC R3 10 k Vin + VCC Rref Rref 10 k - Vref VO + R1 R2 Vref 10k R1 1.0 M Vref [ R3 Rref + R1 1.0 M R3 ] R1 / / Rref / / R2 VH = R1/ / Rref + R2 VO + 10 k VCC R1 R1 / / Rref R2 Vin 10 k Vref = VCC R1 Rref + R1 R2 [ R1 / / Rref Amount of Hysteresis VH R2 VH = [(V -V ] R2 + R3 O(max) O(min) [VO(max) - VO(min)] R2 ơ Rref / / R1 Figure 2. Inverting Comparator with Hysteresis Figure 3. Noninverting Comparator with Hysteresis www.onsemi.com 4 LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 Typical Characteristics (VCC = 15 Vdc, TA = +25°C (each comparator) unless otherwise noted.) 48 42 I IB, INPUT BIAS CURRENT (nA) 1.20 1.00 0.80 TA = -55° C 36 TA = +25° C 30 TA = +125°C 24 18 12 6.0 0 0.60 -50 -25 0 25 50 75 TA, AMBIENT TEMPERATURE (°C) 100 125 0 4.0 8.0 12 16 20 24 VCC, POWER SUPPLY VOLTAGE (Vdc) Figure 4. Normalized Input Offset Voltage 28 Figure 5. Input Bias Current 8.0 IO, OUTPUT CURRENT (mA) NORMALIZED OFFSET VOLTAGE 1.40 7.0 TA = +25° C 6.0 TA = -55° C 5.0 TA = +125°C 4.0 3.0 2.0 1.0 0 100 0 200 300 400 500 Vsat, OUTPUT SATURATION VOLTAGE (mV) Figure 6. Output Sink Current versus Output Saturation Voltage VCC RS Vin Vref VCC ≥ 4.0 V + - VCC RS = Source Resistance R1 ] RS RL kW 1/4 MC14001 +15 100 1/4 MC7400 +5.0 10 CMOS TTL R1 VO + R2 R3 330 k 330 k R4 VCC (V) Device - + C R1 Logic 10 k 100 k RL 330 k VCC T1 T2 T1 = T2 = 0.69 RC 7.2 f[ C(mF) R2 = R3 = R4 R1 [ R2 // R3 // R4 Figure 7. Driving Logic Figure 8. Squarewave Oscillator www.onsemi.com 5 32 LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 APPLICATIONS INFORMATION addition of positive feedback (< 10 mV) is also recommended. It is good design practice to ground all unused input pins. Differential input voltages may be larger than supply voltages without damaging the comparator’s inputs. Voltages more negative than −300 mV should not be used. These quad comparators feature high gain, wide bandwidth characteristics. This gives the device oscillation tendencies if the outputs are capacitively coupled to the inputs via stray capacitance. This oscillation manifests itself during output transitions (VOL to VOH). To alleviate this situation input resistors < 10 kW should be used. The +15 V R1 8.2 k R4 220 k D1 6.8 k R2 Vin R5 220 k 10 k * ) Vin(min) ≈ 0.4 V peak for 1% phase distortion (Dq). VO Vin Vin(min) VCC 15 k R3 q 10 M * Vin D1 prevents input from going negative by more than 0.6 V. R1 + R2 = R3 R5 R3 ≤ for small error in zero crossing 10 + VEE 10 k VO VCC VEE Figure 9. Zero Crossing Detector (Single Supply) q VO Dq Figure 10. Zero Crossing Detector (Split Supplies) www.onsemi.com 6 LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 ORDERING INFORMATION Device Package Shipping† LM239DG SOIC−14 (Pb−Free) 55 Units/Tube LM239DR2G SOIC−14 (Pb−Free) 2500 / Tape & Reel TSSOP−14 (Pb−Free) 2500 / Tape & Reel LM239DTBR2G LM239NG PDIP−14 (Pb−Free) 25 Units/Rail LM339DG SOIC−14 (Pb−Free) 55 Units/Tube LM339DR2G SOIC−14 (Pb−Free) 2500 / Tape & Reel LM339EDR2G SOIC−14 (Pb−Free) 2500 / Tape & Reel TSSOP−14 (Pb−Free) 2500 / Tape & Reel LM339NG PDIP−14 (Pb−Free) 25 Units/Rail LM2901DG SOIC−14 (Pb−Free) 55 Units/Rail LM2901DR2G SOIC−14 (Pb−Free) 2500 / Tape & Reel LM2901EDR2G SOIC−14 (Pb−Free) 2500 / Tape & Reel TSSOP−14 (Pb−Free) 2500 / Tape & Reel LM339DTBR2G LM2901DTBR2G LM2901NG PDIP−14 (Pb−Free) 25 Units/Rail LM2901VDG SOIC−14 (Pb−Free) 55 Units/Tube LM2901VDR2G SOIC−14 (Pb−Free) 2500 / Tape & Reel LM2901VDTBR2G TSSOP−14 (Pb−Free) 2500 / Tape & Reel LM2901VNG PDIP−14 (Pb−Free) 25 Units/Rail NCV2901DR2G* SOIC−14 (Pb−Free) 2500 / Tape & Reel TSSOP−14 (Pb−Free) 2500 / Tape & Reel Bare Die 6000 / Tape & Reel MC3302DG SOIC−14 (Pb−Free) 55 Units/Tube MC3302DR2G SOIC−14 (Pb−Free) 2500 / Tape & Reel TSSOP−14 (Pb−Free) 2500 / Tape & Reel PDIP−14 (Pb−Free) 25 Units/Rail NCV2901DTBR2G* NCV2901CTR* MC3302DTBR2G MC3302PG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable. www.onsemi.com 7 LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 MARKING DIAGRAMS PDIP−14 N, P SUFFIX CASE 646 14 14 14 LM339N AWLYYWWG 1 14 LM2901N AWLYYWWG LM239N AWLYYWWG 1 1 14 LM2901VN AWLYYWWG MC3302P AWLYYWWG 1 1 SOIC−14 D SUFFIX CASE 751A 14 14 14 LM339DG AWLYWW 1 14 LM239DG AWLYWW 1 LM2901DG AWLYWW 1 14 14 * LM2901VDG AWLYWW MC3302DG AWLYWW 1 1 14 LM339EG AWLYWW LM2901EG AWLYWW 1 1 TSSOP−14 DTB SUFFIX CASE 948G 14 14 339 ALYW G G 239 ALYW G G 1 14 1 14 14 2901 V ALYW G G 2901 ALYW G G 1 1 A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week G or G = Pb−Free Package (Note: Microdot may be in either location) *This marking diagram also applies to NCV2901. www.onsemi.com 8 * 3302 ALYW G G 1 LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 PACKAGE DIMENSIONS SOIC−14 CASE 751A−03 ISSUE K D A B 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF AT MAXIMUM MATERIAL CONDITION. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSIONS. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 8 A3 E H L 1 0.25 M DETAIL A 7 B 13X M b 0.25 M C A S B S e DETAIL A h A X 45 _ M A1 C SEATING PLANE DIM A A1 A3 b D E e H h L M MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.19 0.25 0.35 0.49 8.55 8.75 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ SOLDERING FOOTPRINT* 6.50 14X 1.18 1 1.27 PITCH 14X 0.58 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 9 INCHES MIN MAX 0.054 0.068 0.004 0.010 0.008 0.010 0.014 0.019 0.337 0.344 0.150 0.157 0.050 BSC 0.228 0.244 0.010 0.019 0.016 0.049 0_ 7_ LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 PACKAGE DIMENSIONS TSSOP−14 CASE 948G ISSUE B 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. S S N 2X 14 L/2 0.25 (0.010) 8 M B −U− L PIN 1 IDENT. F 7 1 0.15 (0.006) T U N S DETAIL E ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ ÇÇÇ ÉÉÉ K A −V− K1 J J1 SECTION N−N −W− C 0.10 (0.004) −T− SEATING PLANE D G H DIM A B C D F G H J J1 K K1 L M DETAIL E SOLDERING FOOTPRINT 7.06 1 0.65 PITCH 14X 0.36 14X 1.26 DIMENSIONS: MILLIMETERS www.onsemi.com 10 MILLIMETERS INCHES MIN MAX MIN MAX 4.90 5.10 0.193 0.200 4.30 4.50 0.169 0.177 −−− 1.20 −−− 0.047 0.05 0.15 0.002 0.006 0.50 0.75 0.020 0.030 0.65 BSC 0.026 BSC 0.50 0.60 0.020 0.024 0.09 0.20 0.004 0.008 0.09 0.16 0.004 0.006 0.19 0.30 0.007 0.012 0.19 0.25 0.007 0.010 6.40 BSC 0.252 BSC 0_ 8_ 0_ 8_ LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302 PACKAGE DIMENSIONS PDIP−14 CASE 646−06 ISSUE S D 14 A 8 E H E1 1 NOTE 8 7 b2 c B TOP VIEW END VIEW WITH LEADS CONSTRAINED NOTE 5 A2 A NOTE 3 L SEATING PLANE A1 C M D1 eB END VIEW e 14X b SIDE VIEW 0.010 M C A M B M NOTE 6 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. DIMENSIONS A, A1 AND L ARE MEASURED WITH THE PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS−3. 4. DIMENSIONS D, D1 AND E1 DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS ARE NOT TO EXCEED 0.10 INCH. 5. DIMENSION E IS MEASURED AT A POINT 0.015 BELOW DATUM PLANE H WITH THE LEADS CONSTRAINED PERPENDICULAR TO DATUM C. 6. DIMENSION eB IS MEASURED AT THE LEAD TIPS WITH THE LEADS UNCONSTRAINED. 7. DATUM PLANE H IS COINCIDENT WITH THE BOTTOM OF THE LEADS, WHERE THE LEADS EXIT THE BODY. 8. PACKAGE CONTOUR IS OPTIONAL (ROUNDED OR SQUARE CORNERS). DIM A A1 A2 b b2 C D D1 E E1 e eB L M INCHES MIN MAX −−−− 0.210 0.015 −−−− 0.115 0.195 0.014 0.022 0.060 TYP 0.008 0.014 0.735 0.775 0.005 −−−− 0.300 0.325 0.240 0.280 0.100 BSC −−−− 0.430 0.115 0.150 −−−− 10 ° MILLIMETERS MIN MAX −−− 5.33 0.38 −−− 2.92 4.95 0.35 0.56 1.52 TYP 0.20 0.36 18.67 19.69 0.13 −−− 7.62 8.26 6.10 7.11 2.54 BSC −−− 10.92 2.92 3.81 −−− 10 ° ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] ◊ N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative LM339/D