Microchip MCP73842T-420I/MS Advanced single or dual cell lithium-ion/ lithium-polymer charge management controller Datasheet

M
MCP73841/2/3/4
Advanced Single or Dual Cell Lithium-Ion/
Lithium-Polymer Charge Management Controllers
Features
Description
• Linear Charge Management Controllers
• High-Accuracy Preset Voltage Regulation:
- + 0.5% (max)
• Four Preset Voltage Regulation Options:
- 4.1V - MCP73841-4.1, MCP73843-4.1
- 4.2V - MCP73841-4.2, MCP73843-4.2
- 8.2V - MCP73842-8.2, MCP73844-8.2
- 8.4V - MCP73842-8.4, MCP73844-8.4
• Programmable Charge Current
• Programmable Safety Charge Timers
• Preconditioning of Deeply Depleted Cells
• Automatic End-of-Charge Control
• Optional Continuous Cell Temperature
Monitoring (MCP73841 and MCP73842)
• Charge Status Output for Direct LED Drive
• Automatic Power-Down when Input Power
Removed
• Temperature Range: -40°C to 85°C
• Packaging: MSOP-10 - MCP73841, MCP73842
MSOP-8 - MCP73843, MCP73844
The MCP7384X family of devices are highly advanced
linear charge management controllers for use in
space-limited, cost-sensitive applications. The
MCP73841 and MCP73842 combine high accuracy,
constant-voltage, constant-current regulation, cell preconditioning, cell temperature monitoring, advanced
safety timers, automatic charge termination and
charge status indication in space-saving, 10-pin
MSOP packages. The MCP73841 and MCP73842
provide complete, fully-functional, stand-alone charge
management solutions.
Applications
The MCP73842 and MCP73844 are designed for
applications utilizing dual series cell Lithium-Ion or
Lithium-Polymer battery packs. Two preset voltage
regulation options are available (8.2V and 8.4V). The
MCP73842 and MCP73844 operate with an input
voltage range of 8.7V to 12V.
Lithium-Ion/Lithium-Polymer Battery Chargers
Personal Data Assistants
Cellular Telephones
Hand-Held Instruments
Cradle Chargers
Digital Cameras
MP3 Players
10 µF
NDS8434
1
+
8
-
SENSE DRV
2
3
4
100 kΩ
VDD
VBAT
STAT1
EN
MCP73843
 2004 Microchip Technology Inc.
Single
Lithium-Ion
Cell
SENSE
VDD
STAT1
EN
THREF
10 µF
5
0.1 µF
1
2
3
4
5
10
9
8
7
6
DRV
VBAT
VSS
TIMER
THERM
8-Pin MSOP
7
VSS 6
TIMER
Package Types
MCP73841
MCP73842
1A Lithium-Ion Battery Charger
100 mΩ
The MCP7384X family of devices are fully specified
over the ambient temperature range of -40°C to +85°C.
10-Pin MSOP
Typical Application Circuit
MA2Q705
5V
The MCP73841 and MCP73843 are designed for
applications utilizing single-cell Lithium-Ion or LithiumPolymer battery packs. Two preset voltage regulation
options are available (4.1V and 4.2V) for use with either
coke or graphite anodes. The MCP73841 and
MCP73843 operate with an input voltage range of 4.5V
to 12V.
SENSE
VDD
STAT1
EN
1
2
3
4
MCP73843
MCP73844
•
•
•
•
•
•
•
The MCP73843 and MCP73844 employ all the
features of the MCP73841 and MCP73842, with the
exception of the cell temperature monitor. The
MCP73843 and MCP73844 are offered in 8-pin MSOP
packages.
8
7
6
5
DRV
VBAT
VSS
TIMER
DS21823B-page 1
MCP73841/2/3/4
Functional Block Diagram
VDD
1 kΩ
VDD
SENSE
VREF
–
Charge
Current
Amplifier
+
90 kΩ
90 kΩ
IREG/10
VREF
Charge_ok
Precondition
Control
10 kΩ
+
-
Voltage Control
Amplifier
+
-
10 kΩ
Charge
Termination
Comparator
+
-
+
–
12 kΩ
VREF
DRV
Charge Current
Control Amplifier
Precon
VBAT
Precondition
Comp. +
-
300 kΩ
(825 kΩ)
UVLO
Comparator
Constant-Voltage/
Recharge Comp.
VUVLO
EN
+
Power-On
Delay
74.21 kΩ
0.79 kΩ
VREF
150.02 kΩ
Bias and
Reference
Generator
VUVLO
VREF (1.2V)
5.15 kΩ
(4.29 kΩ)
THREF
VSS
100 kΩ
+
-
THERM
Temperature
Comparators
STAT1
Drv Stat 1
50 kΩ
+
50 kΩ
TIMER
IREG/10
Charge Control,
Charge Timers,
And
Status Logic
Oscillator
MCP73841 and MCP73842 Only
DS21823B-page 2
Charge_ok
 2004 Microchip Technology Inc.
MCP73841/2/3/4
1.0
ELECTRICAL
CHARACTERISTICS
*Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Absolute Maximum Ratings †
VDD.................................................................................13.5V
All inputs and outputs w.r.t. VSS ................ -0.3 to (VDD+0.3)V
Current at DRV Pin ......................................................±4 mA
Current at STAT1 Pin .................................................±30 mA
Maximum Junction Temperature, TJ ............................. 150°C
Storage temperature .....................................-65°C to +150°C
ESD protection on all pins:
Human Body Model (1.5 kΩ in Series with 100 pF).......≥ 2 kV
Machine Model (200 pF, No Series Resistance) .............200V
DC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all limits apply for VDD = [VREG(Typ)+0.3V] to 12V, TA = -40°C to +85°C.
Typical values are at +25°C, V DD = [VREG(Typ) + 1V].
Parameters
Sym
Min
Typ
Max
Units
Conditions
MCP73841, MCP73843
4.5
–
12
V
MCP73842, MCP73844
8.7
–
12
V
–
–
0.25
0.75
4
4
µA
mA
MCP73841, MCP73843
4.25
4.45
4.60
V
VDD Low-to-High
MCP73842, MCP73844
8.45
8.65
8.90
V
VDD Low-to-High
MCP73841, MCP73843
4.20
4.40
4.55
V
VDD High-to-Low
MCP73842, MCP73844
8.40
8.60
8.85
V
VDD High-to-Low
MCP73841-4.1,
MCP73843-4.1
4.079
4.1
4.121
V
VDD = [VREG(Typ)+1V], IOUT = 10 mA,
TA = -5°C to +55°C
MCP73841-4.2,
MCP73843-4.2
4.179
4.2
4.221
V
VDD = [VREG(Typ)+1V], IOUT = 10 mA,
TA = -5°C to +55°C
MCP73842-8.2,
MCP73844-8.2
8.159
8.2
8.241
V
VDD = [VREG(Typ)+1V], IOUT = 10 mA,
TA = -5°C to +55°C
MCP73842-8.4,
MCP73844-8.4
8.358
8.4
8.442
V
VDD = [VREG(Typ)+1V], IOUT = 10 mA,
TA = -5°C to +55°C
Supply Input
Supply Voltage
Supply Current
UVLO Start Threshold
UVLO Stop Threshold
V DD
ISS
Disabled
Operating
VDD =VREG(Typ)+1V
VSTART
VSTOP
Voltage Regulation (Constant-Voltage Mode)
Regulated Output Voltage
VREG
Line Regulation
|(∆VBAT/
VBAT )|/∆VDD
–
0.025
0.25
%/V
Load Regulation
|∆VBAT|/VBAT
–
0.01
0.25
%
IOUT = 10 mA to 150 mA,
VDD = [VREG(Typ)+1V]
PSRR
–
-58
–
dB
IOUT = 10 mA, 100 Hz
–
-42
–
dB
IOUT = 10 mA, 1 kHz
–
-30
–
dB
IOUT = 10 mA, 10 kHz
–
0.4
1
µA
VDD Floating, VBAT = VREG(Typ)
110
120
mV
VDD – VSENSE,
TA = -5°C to +55°C
Supply Ripple Attenuation
Output Reverse Leakage
Current
IDISCHARGE
VDD = [VREG(Typ)+1V] to 12V,
IOUT = 10 mA
Current Regulation (Fast Charge Constant-Current Mode)
Fast Charge Current
Regulation Threshold
 2004 Microchip Technology Inc.
VFCS
100
DS21823B-page 3
MCP73841/2/3/4
DC CHARACTERISTICS (CONTINUED)
Electrical Specifications: Unless otherwise indicated, all limits apply for VDD = [VREG(Typ)+0.3V] to 12V, TA = -40°C to +85°C.
Typical values are at +25°C, V DD = [VREG(Typ) + 1V].
Parameters
Sym
Min
Typ
Max
Units
Conditions
Preconditioning Current Regulation (Trickle Charge Constant-Current Mode)
5
10
15
mV
VDD – VSENSE,
TA = -5°C to +55°C
MCP73841-4.1,
MCP73843-4.1
2.70
2.80
2.90
V
VBAT Low-to-High
MCP73841-4.2,
MCP73843-4.2
2.75
2.85
2.95
V
VBAT Low-to-High
MCP73842-8.2,
MCP73844-8.2
5.40
5.60
5.80
V
VBAT Low-to-High
MCP73842-8.4,
MCP73844-8.4
5.50
5.70
5.90
V
VBAT Low-to-High
4
7
10
mV
Precondition Current
Regulation Threshold
VPCS
Precondition Threshold Voltage
VPTH
Charge Termination
Charge Termination Threshold
VTCS
VDD – VSENSE,
TA = -5°C to +55°C
Automatic Recharge
Recharge Threshold Voltage
V RTH
MCP73841,
MCP73843
VREGVREGVREG300 mV 200 mV 100 mV
V
VBAT High-to-Low
MCP73842,
MCP73844
VREGVREGVREG600 mV 400 mV 200 mV
V
VBAT High-to-Low
External MOSFET Gate Drive
Gate Drive Current
IDRV
–
2
–
mA
Sink, CV Mode
–
-0.5
–
mA
Source, CV Mode
Gate Drive Minimum Voltage
VDRVMIN
–
–
1.0
V
VDD = 4.5V
Gate - Source Clamp Voltage
V GS
-7.0
–
-4.5
V
VDD = 12.0V
2.475
2.55
2.625
V
TA = +25°C, VDD = VREG(Typ)+1V,
ITHREF = 0 mA
TC THREF
–
+50
–
ppm/°C
ITHREF
200
–
–
µA
Thermistor Reference Line
Regulation
|(∆VTHREF /
VTHREF )|/
∆VDD
–
0.1
0.25
%/V
Thermistor Reference Load
Regulation
∆VTHREF /
VTHREF
–
0.01
0.10
%
Thermistor Reference - MCP73841, MCP73842
Thermistor Reference Output
Voltage
Temperature Coefficient
Thermistor Reference Source
Current
VTHREF
VDD=[VREG(Typ)+1V] to 12V
ITHREF = 0 mA to 0.20 mA
Thermistor Comparator - MCP73841, MCP73842
VT1
1.18
1.25
1.32
V
VT1HYS
–
-50
–
mV
VT2
0.59
0.62
0.66
V
VT2HYS
–
80
–
mV
|IBIAS|
–
–
2
µA
Sink Current
ISINK
4
7
12
mA
Low Output Voltage
VOL
–
200
400
mV
ISINK = 1 mA
Input Leakage Current
ILK
–
0.01
1
µA
ISINK = 0 mA, VSTAT1 = 12V
Upper Trip Threshold
Upper Trip Point Hysteresis
Lower Trip Threshold
Lower Trip Point Hysteresis
Input Bias Current
Status Indicator
DS21823B-page 4
 2004 Microchip Technology Inc.
MCP73841/2/3/4
DC CHARACTERISTICS (CONTINUED)
Electrical Specifications: Unless otherwise indicated, all limits apply for VDD = [VREG(Typ)+0.3V] to 12V, TA = -40°C to +85°C.
Typical values are at +25°C, V DD = [VREG(Typ) + 1V].
Parameters
Sym
Min
Typ
Max
Units
Input High-Voltage Level
V IH
1.4
-
–
V
Input Low-Voltage Level
VIL
–
-
0.8
V
Input Leakage Current
ILK
–
0.01
1
µA
Conditions
Enable Input
VENABLE = 12V
AC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all limits apply for VDD = [VREG(Typ)+0.3V] to 12V, TA = -40°C to +85°C. Typical values are at +25°C, V DD= [VREG(Typ)+1V].
Parameters
Sym
Min
Typ
Max
Units
tSTART
–
–
5
msec
VDD Low-to-High
tDELAY
–
–
1
msec
VBAT < VPTH to VBAT > VPTH
Current Rise Time Out of
Preconditioning
tRISE
–
–
1
msec
IOUT Rising to 90% of IREG
Fast Charge Safety Timer Period
tFAST
1.2
1.4
1.6
Hours
CTIMER = 0.1 µF
tPRECON
50
60
70
Minutes
CTIMER = 0.1 µF
tTERM
2.5
2.9
3.3
Hours
CTIMER = 0.1 µF
Status Output turn-off
tOFF
–
–
200
µsec
ISINK = 10 mA to 0 mA
Status Output turn-on
tON
–
–
200
µsec
ISINK = 0 mA to 10 mA
UVLO Start Delay
Conditions
Current Regulation
Transition Time Out of
Preconditioning
Preconditioning Current Regulation
Preconditioning Charge Safety
Timer Period
Charge Termination
Elapsed Time Termination Period
Status Indicators
TEMPERATURE SPECIFICATIONS
Electrical Specifications: Unless otherwise specified, all limits apply for VDD= [VREG(Typ)+0.3V] to 12V.
Typical values are at +25°C, V DD= [VREG(Typ)+1.0V].
Parameters
Sym
Min
Typ
Max
Units
Conditions
Temperature Ranges
Specified Temperature Range
TA
-40
+85
°C
Operating Temperature Range
TA
-40
+125
°C
Storage Temperature Range
TA
-65
+150
°C
Thermal Package Resistances
Thermal Resistance, MSOP-10
θJA
113
°C/W
4-Layer JC51-7 Standard Board,
Natural Convection
Thermal Resistance, MSOP-8
θJA
206
°C/W
Single-Layer SEMI G42-88 Board,
Natural Convection
 2004 Microchip Technology Inc.
DS21823B-page 5
MCP73841/2/3/4
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, VDD = [VREG(Typ) + 1V], IOUT = 10 mA and TA= +25°C.
4.203
4.202
+55°C
+85°C
1.00
+25°C
4.200
MCP73841-4.2V
VDD = 5.2 V
1.20
ISS (mA)
VBAT (V)
4.201
1.40
MCP73841-4.2V
VDD = 5.2 V
4.199
0.80
+25°C
0.60
-45°C
0.40
4.198
-5°C
4.197
0.20
4.196
0.00
10
100
1000
10
100
IOUT (mA)
IOUT (mA)
FIGURE 2-1:
Battery Regulation Voltage
(VBAT) vs. Charge Current (IOUT).
4.203
4.202
+55°C
1.40
MCP73841-4.2V
IOUT = 1000 mA
+85°C
1.20
4.199
4.198
+25°C
0.80
0.60
-45°C
0.40
-5°C
4.197
0.20
4.196
0.00
4.5
6.0
7.5
9.0
10.5
12.0
4.5
6.0
VDD (V)
4.203
4.202
+55°C
4.201
9.0
10.5
1.40
MCP73841-4.2V
IOUT = 10 mA
1.20
1.00
ISS (mA)
4.199
4.198
0.80
0.60
-45°C
0.40
-5°C
4.197
+25°C
0.20
4.196
+85°C
0.00
4.5
6.0
7.5
9.0
10.5
12.0
VDD (V)
FIGURE 2-3:
Battery Regulation Voltage
(VBAT) vs. Supply Voltage (VDD).
DS21823B-page 6
12.0
FIGURE 2-5:
Supply Current (ISS) vs.
Supply Voltage (VDD).
MCP73841-4.2V
IOUT = 10 mA
+25°C
4.200
7.5
VDD (V)
FIGURE 2-2:
Battery Regulation Voltage
(VBAT) vs. Supply Voltage (VDD).
VBAT (V)
MCP73841-4.2V
IOUT = 1000 mA
1.00
+25°C
4.200
FIGURE 2-4:
Supply Current (ISS) vs.
Charge Current (IOUT).
ISS (mA)
VBAT (V)
4.201
1000
4.5
6.0
7.5
9.0
10.5
12.0
VDD (V)
FIGURE 2-6:
Supply Current (ISS) vs.
Supply Voltage (VDD).
 2004 Microchip Technology Inc.
MCP73841/2/3/4
Note: Unless otherwise indicated, VDD = [VREG(Typ) + 1V], IOUT = 10 mA and TA= +25°C.
8.408
8.404
+55°C
1.00
+25°C
8.400
MCP73842-8.4V
VDD = 9.4 V
1.20
ISS (mA)
VBAT (V)
8.402
1.40
MCP73842-8.4V
VDD = 9.4 V
8.406
8.398
8.396
0.80
0.60
-45°C
0.40
8.394
0.20
-5°C
8.392
8.390
0.00
10
100
1000
10
100
IOUT (mA)
8.408
8.406
8.404
+55°C
1.40
MCP73842-8.4V
I OUT = 1000 mA
1.20
+85°C
8.398
8.396
+25°C
0.80
0.60
-45°C
0.40
8.394
0.20
-5°C
8.392
8.390
0.00
8.8
9.2
9.6
10
10.4 10.8 11.2 11.6
8.8
12
9.2
9.6
VDD (V)
FIGURE 2-8:
Battery Regulation Voltage
(VBAT) vs. Supply Voltage (VDD).
8.404
MCP73842-8.4V
IOUT = 10 mA
FIGURE 2-11:
Supply Current (ISS) vs.
Supply Voltage (VDD).
1.40
MCP73842-8.4V
IOUT = 10 mA
1.20
+55°C
1.00
8.402
VBAT (V)
10.0 10.4 10.8 11.2 11.6 12.0
VDD (V)
8.400
+25°C
8.398
8.396
8.394
-5°C
ISS (mA)
8.406
MCP73842-8.4V
IOUT = 1000 mA
1.00
+25°C
8.400
FIGURE 2-10:
Supply Current (ISS) vs.
Charge Current (IOUT).
ISS (mA)
VBAT (V)
8.402
1000
IOUT (mA)
FIGURE 2-7:
Battery Regulation Voltage
(VBAT) vs. Charge Current (IOUT).
8.408
+85°C
+25°C
0.80
0.60
8.392
0.20
8.390
0.00
8.8
9.2
9.6
10.0 10.4 10.8 11.2 11.6 12.0
VDD (V)
FIGURE 2-9:
Battery Regulation Voltage
(VBAT) vs. Supply Voltage (VDD).
 2004 Microchip Technology Inc.
-45°C
0.40
+25°C
+85°C
8.8
9.2
9.6
10.0 10.4 10.8 11.2 11.6 12.0
VDD (V)
FIGURE 2-12:
Supply Current (ISS) vs.
Supply Voltage (VDD).
DS21823B-page 7
MCP73841/2/3/4
Note: Unless otherwise indicated, VDD = [VREG(Typ) + 1V], IOUT = 10 mA and TA= +25°C.
0.45
0.70
0.30
0.25
+85°C
0.20
0.15
+25°C
0.10
0.05
+85°C
0.60
0.50
+25°C
0.40
0.30
0.20
-45°C
0.10
-45°C
0.00
0.00
2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2
4.0 4.4 4.8 5.2 5.6 6.0 6.4 6.8 7.2 7.6 8.0 8.4
VBAT (V)
VBAT (V)
FIGURE 2-13:
Output Reverse Leakage
Current (IDISCHARGE) vs. Battery Voltage (VBAT).
2.560
2.558
2.556
2.554
2.552
2.550
2.548
2.546
2.544
2.542
2.540
FIGURE 2-16:
Output Reverse Leakage
Current (IDISCHARGE) vs. Battery Voltage (VBAT).
MCP73841-4.2V
VDD = 5.2 V
+85°C
VTHREF (V)
VTHREF (V)
MCP73842-8.4V
VDD = Float
0.80
IDISCHARGE (µA)
0.35
IDISCHARGE (µA)
0.90
MCP73841-4.2V
VDD = Float
0.40
+25°C
-45°C
0
25
50
75
100
125
150 175
2.560
2.558
2.556
2.554
2.552
2.550
2.548
2.546
2.544
2.542
2.540
200
MCP73842-8.4V
VDD = 9.4 V
+85°C
+25°C
-45°C
0
25
50
I THREF (µA)
2.568
150 175
200
MCP73842-8.4V
I THREF = 100 µA
2.564
2.560
2.556
VTHREF (V)
2.560
VTHREF (V)
125
FIGURE 2-17:
Thermistor Reference
Voltage (VTHREF) vs. Thermistor Bias Current
(ITHREF).
MCP73841-4.2V
I THREF = 100 µA
2.564
100
I THREF (µA)
FIGURE 2-14:
Thermistor Reference
Voltage (VTHREF) vs. Thermistor Bias Current
(ITHREF).
2.568
75
+85°C
2.552
+25°C
2.548
+85°C
2.552
+25°C
2.548
-45°C
2.544
2.556
-45°C
2.544
2.540
2.540
4.5
6.0
7.5
9.0
10.5
12.0
VDD (V)
FIGURE 2-15:
Thermistor Reference
Voltage (VTHREF) vs. Supply Voltage (VDD).
DS21823B-page 8
8.8
9.2
9.6
10.0 10.4 10.8 11.2 11.6 12.0
VDD (V)
FIGURE 2-18:
Thermistor Reference
Voltage (VTHREF) vs. Supply Voltage (VDD).
 2004 Microchip Technology Inc.
MCP73841/2/3/4
Note: Unless otherwise indicated, VDD = [VREG(Typ) + 1V], IOUT = 10 mA and TA= +25°C.
VDD
VDD
VBAT
VBAT
MCP73841-4.2V
VDD Stepped From 5.2V to 6.2V
IOUT = 500 mA
COUT = 10 µF, X7R, Ceramic
MCP73841-4.2V
VDD Stepped From 5.2V to 6.2V
IOUT = 10 mA
COUT = 10 µF, X7R, Ceramic
FIGURE 2-19:
Line Transient Response.
MCP73841-4.2V
VDD = 5.2V
COUT = 10 µF, X7R, Ceramic
FIGURE 2-22:
MCP73841-4.2V
VDD = 5.2V
COUT = 10 µF, X7R, Ceramic
VBAT
100 mA
Line Transient Response.
IOUT
500 mA
FIGURE 2-23:
0
0
-10
-10
-20
-30
-40
MCP73841-4.2V
VDD = 5.2 V
VAC = 100 mVp-p
IOUT = 10 mA
COUT = 10 µF, X7R, CERAMIC
-60
-70
-80
0.01
0.1
1
10
100
1000
Attenuation (dB)
Attenuation (dB)
Load Transient Response.
-50
Power Supply Ripple
 2004 Microchip Technology Inc.
Load Transient Response.
-20
-30
-40
MCP73841-4.2V
VDD = 5.2 V
VAC = 100 mVp-p
IOUT = 100 mA
COUT = 10 µF, X7R, CERAMIC
-50
-60
-70
-80
0.01
Frequency (kHz)
FIGURE 2-21:
Rejection.
IOUT
10 mA
10 mA
FIGURE 2-20:
VBAT
0.1
1
10
100
1000
Frequency (kHz)
FIGURE 2-24:
Rejection.
Power Supply Ripple
DS21823B-page 9
MCP73841/2/3/4
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN DESCRIPTION TABLE
MCP73841,
MCP73842
Pin No.
MCP73843,
MCP73844
Pin No.
Name
1
1
SENSE
2
2
VDD
3
3
STAT1
4
4
EN
5
—
THREF
6
—
THERM
Cell Temperature Sensor Input
7
5
TIMER
Timer Set
8
6
VSS
Battery Management 0V Reference
9
7
VBAT
Battery Voltage Sense
10
8
DRV
Drive Output
3.1
Charge Current Sense Input
(SENSE)
Charge current is sensed via the voltage developed
across an external precision sense resistor. The sense
resistor must be placed between the supply voltage
(VDD) and the external pass transistor (Q1). A 220 mΩ
sense resistor produces a fast charge current of
500 mA, typically.
3.2
Battery Management Input Supply
(VDD)
A supply voltage of [VREG(Typ) + 0.3V] to 12V is
recommended. Bypass to VSS with a minimum of
4.7 µF.
3.3
Charge Status Output (STAT1)
Function
Charge Current Sense Input
Battery Management Input Supply
Charge Status Output
Logic Enable
Cell Temperature Sensor Bias
3.6
Cell Temperature Sensor Input
(THERM)
Input for an external thermistor for continuous celltemperature monitoring and pre-qualification. Apply a
voltage equal to 0.85V to disable temperature-sensing.
3.7
Timer Set (TIMER)
All safety timers are scaled by CTIMER/0.1 µF.
3.8
Battery Management 0V Reference
(VSS)
Connect to negative terminal of battery.
3.9
Battery Voltage Sense (VBAT)
Current limited, open-drain drive for direct connection
to a LED for charge status indication. Alternatively, a
pull-up resistor can be applied for interfacing to a host
microcontroller.
Voltage sense input. Connect to positive terminal of
battery. Bypass to VSS with a minimum of 4.7 µF to
ensure loop stability when the battery is disconnected.
A precision internal resistor divider regulates the final
voltage on this pin to VREG.
3.4
3.10
Logic Enable (EN)
Input to force charge termination, initiate charge, clear
faults or disable automatic recharge.
3.5
Drive Output (DRV)
Direct output drive of an external P-channel MOSFET
for current and voltage regulation.
Cell Temperature Sensor Bias
(THREF)
Voltage reference to bias external thermistor for
continuous
cell
temperature
monitoring
and
prequalification.
DS21823B-page 10
 2004 Microchip Technology Inc.
MCP73841/2/3/4
4.0
DEVICE OVERVIEW
The MCP7384X family of devices are highly advanced,
linear charge management controllers. Figure 4-1
depicts the operational flow algorithm from charge
initiation to completion and automatic recharge.
4.1
Charge Qualification and
Preconditioning
Upon insertion of a battery or application of an external
supply, the MCP7384X family of devices automatically
perform a series of safety checks to qualify the charge.
The input source voltage must be above the
undervoltage lockout threshold, the enable pin must be
above the logic-high level and the cell temperature
monitor must be within the upper and lower thresholds.
The cell temperature monitor applies to both the
MCP73841 and MCP73842, with the qualification
parameters being continuously monitored. Deviation
beyond the limits automatically suspends or terminates
the charge cycle.
Once the qualification parameters have been met, the
MCP7384X initiates a charge cycle. The charge status
output is pulled low throughout the charge cycle (see
Table 5-1 for charge status outputs). If the battery
voltage is below the preconditioning threshold (VPTH),
the MCP7384X preconditions the battery with a tricklecharge. The preconditioning current is set to
approximately 10% of the fast charge regulation
current. The preconditioning trickle-charge safely
replenishes deeply depleted cells and minimizes heat
dissipation in the external pass transistor during the
initial charge cycle. If the battery voltage has not
exceeded the preconditioning threshold before the
preconditioning timer has expired, a fault is indicated
and the charge cycle is terminated.
4.2
4.3
Constant-Voltage Regulation
When the battery voltage reaches the regulation
voltage (VREG), constant-voltage regulation begins.
The MCP7384X monitors the battery voltage at the
VBAT pin. This input is tied directly to the positive
terminal of the battery. The MCP7384X is offered in
four fixed-voltage versions for single or dual series cell
battery packs with either coke or graphite anodes:
-
4.4
4.1V
4.2V
8.2V
8.4V
(MCP73841-4.1, MCP73843-4.1)
(MCP73841-4.2, MCP73843-4.2)
(MCP73842-8.2, MCP73844-8.2)
(MCP73842-8.4, MCP73844-8.4)
Charge Cycle Completion and
Automatic Re-Charge
The MCP7384X monitors the charging current during
the constant-voltage regulation phase. The charge
cycle is considered complete when the charge current
has diminished below approximately 7% of the
regulation current (IREG) or the elapsed timer has
expired.
The MCP7384X automatically begins a new charge
cycle when the battery voltage falls below the recharge
threshold (VRTH), assuming all the qualification
parameters are met.
Constant-Current Regulation –
Fast Charge
Preconditioning ends and fast charging begins, when
the battery voltage exceeds the preconditioning
threshold. Fast charge regulates to a constant-current,
IREG, based on the supply voltage minus the voltage at
the SENSE input (VFCS) developed by the drop across
an external sense resistor (RSENSE). Fast charge
continues until the battery voltage reaches the
regulation voltage (VREG); or until the fast charge timer
expires. In this case, a fault is indicated and the charge
cycle is terminated.
 2004 Microchip Technology Inc.
DS21823B-page 11
 2004 Microchip Technology Inc.
Initialize
Note: The qualification parameters are continuously
monitored throughout the charge cycle.
Note
VDD > VUVLO
EN High
No
STAT1 = Off
Yes
Note
Temperature OK
Yes
Preconditioning Phase
Charge Current = IPREG
Reset Safety Timer
No
VBAT > VPTH
No
STAT1 = Flashing
Charge Current = 0
STAT1 = On
Yes
VBAT > VPTH
Constant-Current
Phase
Charge Current = IREG
Reset Safety Timer
Yes
VBAT = VREG
No
No
Yes
DS21823B-page 12
FIGURE 4-1:
IOUT < ITERM
Elapsed Timer
Expired
Yes
No
Yes Fault
Charge Current = 0
Reset Safety Timer
Yes
Safety Timer
Expired
No
No
Yes
Temperature OK
No
STAT1 = Flashing
Safety Timer Suspended
Charge Current = 0
Yes
VDD < VUVLO
Temperature OK
Temperature OK
or EN Low
No
No
No
Yes STAT1 = Flashing
STAT1 = Flashing
STAT1 = Flashing
Safety Timer Suspended
Safety Timer Suspended
Charge Current = 0
Charge Current = 0
Operational Flow Algorithm - MCP73841 and MCP73842.
Yes Charge Termination
Charge Current = 0
Reset Safety Timer
VDD < VUVLO
VBAT < VRTH
or EN Low
Yes
No
STAT1 = Off
MCP73841/2/3/4
Safety Timer
Expired
Constant-Voltage Phase
Output Voltage = V REG
MCP73841/2/3/4
5.0
DETAILED DESCRIPTION
5.1
Analog Circuitry
5.1.1
For NTC thermistors:
2 × R COLD × R H OT
R T1 = ---------------------------------------------R COLD – R H OT
CHARGE CURRENT SENSE INPUT
(SENSE)
Fast charge current regulation is maintained by the
voltage drop developed across an external sense
resistor (R SENSE) applied to the SENSE input pin. The
following formula calculates the value for RSENSE:
R SENSE
2 × R COLD × R H OT
R T2 = ---------------------------------------------R COLD – 3 × R H OT
For PTC thermistors:
2 × R COLD × R H OT
R T1 = ---------------------------------------------R H OT – R CO LD
V FCS
= -----------I REG
2 × R COLD × R H OT
R T2 = ---------------------------------------------R H OT – 3 × R CO LD
where:
IREG is the desired fast charge current in amps
The preconditioning trickle-charge current and the
charge termination current are scaled to approximately
10% and 7% of IREG , respectively.
5.1.2
BATTERY MANAGEMENT INPUT
SUPPLY (VDD)
The VDD input is the input supply to the MCP7384X.
The MCP7384X automatically enters a power-down
mode if the voltage on the VDD input falls below the
undervoltage lockout voltage (VSTOP). This feature
prevents draining the battery pack when the VDD
supply is not present.
5.1.3
CELL TEMPERATURE SENSOR
BIAS (THREF)
A 2.55V voltage reference is provided to bias an
external thermistor for continuous cell temperature
monitoring and pre-qualification. A ratio metric window
comparison is performed at threshold levels of
V THREF/2 and VTHREF/4. Cell temperature monitoring
is provided by both the MCP73841 and MCP73842.
5.1.4
CELL TEMPERATURE SENSOR
INPUT (THERM)
The MCP73841 and MCP73842 continuously monitor
temperature by comparing the voltage between the
THERM input and VSS with the upper and lower
temperature thresholds. A negative or positive
temperature coefficient (NTC or PTC) thermistor and
an external voltage divider typically develop this
voltage. The temperature-sensing circuit has its own
reference, to which it performs a ratio metric
comparison. Therefore, it is immune to fluctuations in
the supply input (VDD). The temperature-sensing circuit
is removed from the system when VDD is not applied,
eliminating additional discharge of the battery pack.
where:
RCOLD and R HOT are the thermistor resistance
values at the temperature window of interest.
Applying a voltage equal to 0.85V to the THERM input
disables temperature monitoring.
5.1.5
TIMER SET INPUT (TIMER)
The TIMER input programs the period of the safety
timers by placing a timing capacitor (CTIMER) between
the TIMER input pin and VSS. Three safety timers are
programmed via the timing capacitor.
The preconditioning safety timer period:
C TIMER
t PRE CON = ------------------ × 1.0Hour s
0.1µF
The fast charge safety timer period:
C TIMER
t FAST = ------------------ × 1.5Hours
0.1µF
The elapsed time termination period:
C TIMER
t TERM = ------------------ × 3.0Hours
0.1µF
The preconditioning timer starts after qualification and
resets when the charge cycle transitions to the constant-current, fast charge phase. The fast charge and
elapsed timers start once the MCP7384X transitions
from preconditioning. The fast charge timer resets
when the charge cycle transitions to the constant-voltage phase. The elapsed timer will expire and terminate
the charge if the sensed current does not diminish
below the termination threshold.
Figure 6-1 depicts a typical application circuit with
connection of the THERM input. The resistor values of
RT1 and RT2 are calculated with the following
equations.
 2004 Microchip Technology Inc.
DS21823B-page 13
MCP73841/2/3/4
5.1.6
BATTERY VOLTAGE SENSE (VBAT)
The MCP7384X monitors the battery voltage at the
VBAT pin. This input is tied directly to the positive
terminal of the battery. The MCP7384X is offered in
four fixed-voltage versions for single or dual series cell
battery packs, with either coke or graphite anodes:
-
4.1V
4.2V
8.2V
8.4V
5.1.7
(MCP73841-4.1, MCP73843-4.1)
(MCP73841-4.2, MCP73843-4.2)
(MCP73842-8.2, MCP73844-8.2)
(MCP73842-8.4, MCP73844-8.4)
DRIVE OUTPUT (DRV)
The MCP7384X controls the gate drive to an external
P-channel MOSFET. The P-channel MOSFET is
controlled in the linear region regulating current and
voltage supplied to the cell. The drive output is
automatically turned off when the voltage on the VDD
input falls below the undervoltage lockout voltage
(VSTOP).
5.2
5.2.1
Digital Circuitry
CHARGE STATUS OUTPUT (STAT1)
A status output provides information on the state-ofcharge. The current-limited, open-drain output can be
used to illuminate an external LED. Optionally, a pull-up
resistor can be used on the output for communication
with a host microcontroller. Table 5-1 summarizes the
state of the status output during a charge cycle.
TABLE 5-1:
STATUS OUTPUTS
Charge Cycle State
Stat1
Qualification
OFF
Preconditioning
ON
Constant-Current Fast
Charge
ON
Constant-Voltage
ON
Charge Complete
OFF
Safety Timer Fault
Flashing
(1 Hz, 50% duty cycle)
Cell Temperature Invalid
Flashing
(1 Hz, 50% duty cycle)
Disabled - Sleep mode
OFF
Battery Disconnected
OFF
The flashing rate (1 Hz) is based off a timer capacitor
(CTIMER) of 0.1 µF. The rate will vary based on the
value of the timer capacitor.
5.2.2
LOGIC ENABLE (EN)
The logic-enable input pin (EN) can be used to
terminate a charge anytime during the charge cycle,
initiate a charge cycle or initiate a recharge cycle.
Applying a logic-high input signal to the EN pin, or tying
it to the input source, enables the device. Applying a
logic-low input signal disables the device and
terminates a charge cycle. When disabled, the device’s
supply current is reduced to 0.25 µA, typically.
DS21823B-page 14
 2004 Microchip Technology Inc.
MCP73841/2/3/4
6.0
APPLICATIONS
cells: constant-current followed by constant-voltage.
Figure 6-1 depicts a typical stand-alone application
circuit, while Figure 6-2 depicts the accompanying
charge profile.
The MCP7384X is designed to operate in conjunction
with either a host microcontroller or in stand-alone
applications. The MCP7384X provides the preferred
charge algorithm for Lithium-Ion and Lithium-Polymer
Voltage
Regulated
Wall Cube
Optional
Reverse
Blocking
Diode
Q1
RSENSE
SENSE
VDD
STAT1
RT1
10 DRV
VBAT
1
2
9
3
MCP73841 8
EN 4
THREF 5
7
VSS
TIMER
CTIMER
6 THERM
RT2
FIGURE 6-1:
+
-
Battery
Pack
Typical Application Circuit.
Preconditioning
Phase
Constant-Current
Phase
Constant-Voltage
Phase
Regulation Voltage
(VREG)
Regulation Current
(IREG)
Charge
Voltage
Transition Threshold
(V PTH)
Charge
Current
Precondition Current
(IPREG)
Termination Current
(ITERM)
Precondition
Safety Timer
Fast Charge
Safety Timer
Elapsed Time
Termination Timer
FIGURE 6-2:
Typical Charge Profile.
 2004 Microchip Technology Inc.
DS21823B-page 15
MCP73841/2/3/4
6.1
Application Circuit Design
Due to the low efficiency of linear charging, the most
important factors are thermal design and cost, which are
a direct function of the input voltage, output current and
thermal impedance between the external P-channel
pass transistor and the ambient cooling air. The worstcase situation occurs when the device has transitioned
from the preconditioning phase to the constant-current
phase. In this situation, the P-channel pass transistor
has to dissipate the maximum power. A trade-off must
be made between the charge current, cost and thermal
requirements of the charger.
6.1.1
COMPONENT SELECTION
Selection of the external components in Figure 6-1 are
crucial to the integrity and reliability of the charging
system. The following discussion is intended to be a
guide for the component selection process.
6.1.1.1
Sense Resistor
The preferred fast charge current for Lithium-Ion cells
is at the 1C rate, with an absolute maximum current at
the 2C rate. For example, a 500 mAh battery pack has
a preferred fast charge current of 500 mA. Charging at
this rate provides the shortest charge cycle times
without degradation to the battery pack performance or
life.
The current sense resistor (RSENSE) is calculated by:
V FCS
R SENSE = -----------I REG
6.1.1.2
External Pass Transistor
The external P-channel MOSFET is determined by the
gate-to-source threshold voltage, input voltage, output
voltage and fast charge current. Therefore, the
selected P-channel MOSFET must satisfy the thermal
and electrical design requirements.
Thermal Considerations
The worst-case power dissipation in the external pass
transistor occurs when the input voltage is at the
maximum and the device has transitioned from the
preconditioning phase to the constant-current phase.
In this case, the power dissipation is:
Pow erDi ssipation = ( V DDM AX – V PTHMIN ) × IREGMAX
Where:
VDDMAX is the maximum input voltage.
IREGMAX is the maximum fast charge current.
VPTHMIN is the minimum transition threshold voltage.
Power dissipation with a 5V, ±10% input voltage
source, 220 mΩ, 1% sense resistor is:
Po we rDissipation = ( 5.5V – 2.75V ) × 551 mA = 1.52W
Utilizing a Fairchild™ NDS8434 or an International
Rectifier IRF7404 mounted on a 1in2 pad of 2 oz.
copper, the junction temperature rise is 75°C,
approximately. This would allow for a maximum
operating ambient temperature of 75°C.
Where:
IREG is the desired fast charge current.
By increasing the size of the copper pad, a higher
ambient temperature can be realized, or a lower value
sense resistor could be utilized.
For the 500 mAh battery pack example, a standard
value 220 mΩ, 1% resistor provides a typical fast
charge current of 500 mA and a maximum fast charge
current of 551 mA. Worst-case power dissipation in the
sense resistor is:
Alternatively, different package options can be utilized
for more or less power dissipation. Again, design tradeoffs should be considered to minimize size while
maintaining the desired performance.
2
PowerDissipation = 220mΩ × 551mA = 66.8mW
A Panasonic® ERJ-6RQFR22V, 220 mW, 1%, 1/8W
resistor in a standard 0805 package is more than
sufficient for this application.
A larger value sense resistor will decrease the fast
charge current and power dissipation in both the sense
resistor and external pass transistor, but will increase
charge cycle times. Design trade-offs must be
considered to minimize space while maintaining the
desired performance.
Electrical Considerations
The gate-to-source threshold voltage and R DSON of the
external P-channel MOSFET must be considered in the
design phase.
The worst-case VGS provided by the controller occurs
when the input voltage is at the minimum and the fast
charge current regulation threshold is at the maximum.
The worst-case VGS is:
V GS = V DR VMAX – ( V DDMIN – V FCSMAX )
Where:
VDRVMAX is the maximum sink voltage at the
V DRV output
VDDMIN is the minimum input voltage source
VFCSMAX is the maximum fast charge current
regulation threshold
DS21823B-page 16
 2004 Microchip Technology Inc.
MCP73841/2/3/4
Worst-case VGS with a 5V, ±10% input voltage source
and a maximum sink voltage of 1.0V is:
V GS = 1.0V – ( 4.5V – 120mV ) = – 3.38V
At this worst-case (VGS) the RDSON of the MOSFET
must be low enough as to not impede the performance
of the charging system. The maximum allowable
RDSON at the worst-case VGS is:
V DDMIN – V FCSMAX – V BATMAX
R D SON = ------------------------------------------------------------------------------I REGMAX
4.5V – 120 ( 115 )mV – 4.221V
R D SO N = ------------------------------------------------------------------------- = 288mΩ
551 ( 581 )mA
The Fairchild NDS8434 and International Rectifier
IRF7404 both satisfy these requirements.
6.1.1.3
EXTERNAL CAPACITORS
The MCP7384X are stable with or without a battery
load. In order to maintain good AC stability in the
Constant-Voltage mode, a minimum capacitance of
4.7 µF is recommended to bypass the VBAT pin to VSS.
This capacitance provides compensation when there is
no battery load. Additionally, the battery and
interconnections appear inductive at high frequencies.
These elements are in the control feedback loop during
Constant-Voltage mode. Therefore, the bypass
capacitance may be necessary to compensate for the
inductive nature of the battery pack.
6.1.1.5
ENABLE INTERFACE
In the stand-alone configuration, the enable pin is
generally tied to the input voltage. The MCP7384X
automatically enters a Low-power mode when voltage
on the VDD input falls below the undervoltage lockout
voltage (VSTOP), reducing the battery drain current to
0.4 µA, typically.
6.1.1.6
CHARGE STATUS INTERFACE
A status output provides information on the state of
charge. The current-limited, open-drain output can be
used to illuminate an external LED. Refer to Table 5-1
for a summary of the state of the status output during a
charge cycle.
6.2
PCB Layout Issues
For optimum voltage regulation, place the battery pack
as close as possible to the device’s VBAT and VSS pins.
This is recommended to minimize voltage drops along
the high current-carrying PCB traces.
If the PCB layout is used as a heatsink, adding many
vias around the external pass transistor can help
conduct more heat to the back plane of the PCB, thus
reducing the maximum junction temperature.
Virtually any good quality output filter capacitor can be
used, independent of the capacitor’s minimum ESR
(Effective Series Resistance) value. The actual value of
the capacitor and its associated ESR depends on the
forward transconductance (gm) and capacitance of the
external pass transistor. A 4.7 µF tantalum or
aluminum electrolytic capacitor at the output is usually
sufficient to ensure stability for up to a 1A output
current.
6.1.1.4
REVERSE-BLOCKING PROTECTION
The optional reverse-blocking protection diode,
depicted in Figure 6-1, provides protection from a
faulted or shorted input, or from a reversed-polarity
input source. Without the protection diode, a faulted or
shorted input would discharge the battery pack through
the body diode of the external pass transistor.
If a reverse-protection diode is incorporated into the
design, it should be chosen to handle the fast charge
current continuously at the maximum ambient
temperature. In addition, the reverse-leakage current
of the diode should be kept as small as possible.
 2004 Microchip Technology Inc.
DS21823B-page 17
MCP73841/2/3/4
7.0
PACKAGING INFORMATION
7.1
Package Marking Information
8-Lead MSOP (MCP73843, MCP73844)
738431
0319256
XXXXX
YWWNNN
10-Lead MSOP (MCP73841, MCP73842)
YYWWNNN
Note:
*
XX...X
YY
WW
NNN
Example:
738411
0319256
XXXXX
Legend:
Example:
Customer specific information*
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line thus limiting the number of available characters
for customer specific information.
Standard marking consists of Microchip part number, year code, week code, and traceability code.
DS21823B-page 18
 2004 Microchip Technology Inc.
MCP73841/2/3/4
8-Lead Plastic Micro Small Outline Package (MS) (MSOP)
E
E1
p
D
2
B
n
1
α
A2
A
c
φ
A1
(F)
L
β
Units
Dimension Limits
n
p
MIN
INCHES
NOM
MAX
MILLIMETERS*
NOM
8
0.65 BSC
0.75
0.85
0.00
4.90 BSC
3.00 BSC
3.00 BSC
0.40
0.60
0.95 REF
0°
0.08
0.22
5°
5°
-
MIN
8
Number of Pins
.026 BSC
Pitch
A
.043
Overall Height
A2
.030
.033
.037
Molded Package Thickness
A1
.006
.000
Standoff
E
.193 TYP.
Overall Width
E1
.118 BSC
Molded Package Width
D
.118 BSC
Overall Length
L
.016
.024
.031
Foot Length
Footprint (Reference)
F
.037 REF
φ
Foot Angle
0°
8°
c
Lead Thickness
.003
.006
.009
B
.009
.012
.016
Lead Width
α
5°
15°
Mold Draft Angle Top
β
5°
15°
Mold Draft Angle Bottom
*Controlling Parameter
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not
exceed .010" (0.254mm) per side.
MAX
1.10
0.95
0.15
0.80
8°
0.23
0.40
15°
15°
JEDEC Equivalent: MO-187
Drawing No. C04-111
 2004 Microchip Technology Inc.
DS21823B-page 19
MCP73841/2/3/4
10-Lead Plastic Micro Small Outline Package (UN) (MSOP)
E
E1
p
D
2
B
n
1
α
A
φ
c
A2
A1
L
(F)
β
L1
Units
Dimension Limits
n
p
MIN
INCHES
NOM
10
.020 TYP
.033
.193 BSC
.118 BSC
.118 BSC
.024
.037 REF
.009
-
MAX
MILLIMETERS*
NOM
10
0.50 TYP.
0.85
0.75
0.00
4.90 BSC
3.00 BSC
3.00 BSC
0.60
0.40
0.95 REF
0°
0.08
0.15
0.23
5°
5°
MIN
Number of Pins
Pitch
.043
Overall Height
A
Molded Package Thickness
A2
.030
.037
Standoff
A1
.000
.006
Overall Width
E
Molded Package Width
E1
Overall Length
D
Foot Length
L
.016
.031
Footprint
F
φ
0°
8°
Foot Angle
c
.003
Lead Thickness
.009
B
.006
Lead Width
.012
α
5°
15°
Mold Draft Angle Top
β
5°
15°
Mold Draft Angle Bottom
*Controlling Parameter
Notes:
Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not
exceed .010" (0.254mm) per side.
MAX
1.10
0.95
0.15
0.80
8°
0.23
0.30
15°
15°
JEDEC Equivalent: MO-187
Drawing No. C04-021
DS21823B-page 20
 2004 Microchip Technology Inc.
MCP73841/2/3/4
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
XXX
X
XX
Device
Preset
Voltage
Options
Temperature
Range
Package
Device
MCP73841:
MCP73842:
MCP73842T:
MCP73843:
MCP73843T:
MCP73844:
MCP73844T:
410
420
820
840
Temperature Range
I
Package
MS
UN
a)
b)
c)
d)
MCP73841T:
Preset Voltage
Regulation Options
Examples:
=
=
=
=
Single-cell charge controller with temperature
monitor
Single-cell charge controller with temperature
monitor, Tape and Reel
Dual series cells charge controller with temperature monitor
Dual series cells charge controller with temperature monitor, Tape and Reel
Single-cell charge controller
Single-cell charge controller, Tape and Reel
Dual series cells charge controller
Dual series cells charge controller,
Tape and Reel
4.1V
4.2V
8.2V
8.4V
= -40°C to +85°C (Industrial)
a)
b)
c)
d)
a)
b)
c)
d)
a)
b)
c)
d)
MCP73841-410I/UN: 4.1V Preset Voltage
MCP73841T-410I/UN: 4.1V Preset Voltage,
Tape and Reel
MCP73841-420I/UN: 4.2V Preset Voltage
MCP73841T-420I/UN: 4.2V Preset Voltage,
Tape and Reel
MCP73842-820I/UN: 8.2V Preset Voltage
MCP73842T-820I/UN: 8.2V Preset Voltage,
Tape and Reel
MCP73842-840I/UN: 8.4V Preset Voltage
MCP73842T-840I/UN: 8.4V Preset Voltage,
Tape and Reel
MCP73843-410I/MS: 4.1V Preset Voltage
MCP73843T-410I/MS: 4.1V Preset Voltage,
Tape and Reel
MCP73843-420I/MS: 4.2V Preset Voltage
MCP73843T-420I/MS: 4.2V Preset Voltage,
Tape and Reel
MCP73844-820I/MS: 8.2V Preset Voltage
MCP73844T-820I/MS: 8.2V Preset Voltage,
Tape and Reel
MCP73844-840I/MS: 8.4V Preset Voltage
MCP73844T-840I/MS: 8.4V Preset Voltage,
Tape and Reel
= Plastic Micro Small Outline (MSOP), 8-lead
= Plastic Micro Small Outline (MSOP), 10-lead
Sales and Support
Data Sheets
Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and
recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1.
2.
3.
Your local Microchip sales office
The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277
The Microchip Worldwide Site (www.microchip.com)
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using.
Customer Notification System
Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
 2004 Microchip Technology Inc.
DS21823B-page 21
MCP73841/2/3/4
NOTES:
DS21823B-page 22
 2004 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is intended through suggestion only
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
No representation or warranty is given and no liability is
assumed by Microchip Technology Incorporated with respect
to the accuracy or use of such information, or infringement of
patents or other intellectual property rights arising from such
use or otherwise. Use of Microchip’s products as critical
components in life support systems is not authorized except
with express written approval by Microchip. No licenses are
conveyed, implicitly or otherwise, under any intellectual
property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, MPLAB, PIC, PICmicro, PICSTART,
PRO MATE, PowerSmart and rfPIC are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
AmpLab, FilterLab, microID, MXDEV, MXLAB, PICMASTER,
SEEVAL, SmartShunt and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Application Maestro, dsPICDEM, dsPICDEM.net,
dsPICworks, ECAN, ECONOMONITOR, FanSense,
FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP,
ICEPIC, Migratable Memory, MPASM, MPLIB, MPLINK,
MPSIM, PICkit, PICDEM, PICDEM.net, PICtail, PowerCal,
PowerInfo, PowerMate, PowerTool, rfLAB, Select Mode,
SmartSensor, SmartTel and Total Endurance are trademarks
of Microchip Technology Incorporated in the U.S.A. and other
countries.
Serialized Quick Turn Programming (SQTP) is a service mark
of Microchip Technology Incorporated in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2004, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 quality system certification for
its worldwide headquarters, design and wafer fabrication facilities in
Chandler and Tempe, Arizona and Mountain View, California in October
2003. The Company’s quality system processes and procedures are for
its PICmicro® 8-bit MCUs, KEEL OQ® code hopping devices, Serial
EEPROMs, microperipherals, nonvolatile memory and analog
products. In addition, Microchip’s quality system for the design and
manufacture of development systems is ISO 9001:2000 certified.
 2004 Microchip Technology Inc.
DS21823B-page 23
M
WORLDWIDE SALES AND SERVICE
AMERICAS
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support: 480-792-7627
Web Address: http://www.microchip.com
China - Beijing
Korea
Unit 706B
Wan Tai Bei Hai Bldg.
No. 6 Chaoyangmen Bei Str.
Beijing, 100027, China
Tel: 86-10-85282100
Fax: 86-10-85282104
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku
Seoul, Korea 135-882
Tel: 82-2-554-7200 Fax: 82-2-558-5932 or
82-2-558-5934
China - Chengdu
200 Middle Road
#07-02 Prime Centre
Singapore, 188980
Tel: 65-6334-8870 Fax: 65-6334-8850
3780 Mansell Road, Suite 130
Alpharetta, GA 30022
Tel: 770-640-0034
Fax: 770-640-0307
Rm. 2401-2402, 24th Floor,
Ming Xing Financial Tower
No. 88 TIDU Street
Chengdu 610016, China
Tel: 86-28-86766200
Fax: 86-28-86766599
Boston
China - Fuzhou
Atlanta
2 Lan Drive, Suite 120
Westford, MA 01886
Tel: 978-692-3848
Fax: 978-692-3821
Chicago
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
4570 Westgrove Drive, Suite 160
Addison, TX 75001
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Tri-Atria Office Building
32255 Northwestern Highway, Suite 190
Farmington Hills, MI 48334
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
2767 S. Albright Road
Kokomo, IN 46902
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
18201 Von Karman, Suite 1090
Irvine, CA 92612
Tel: 949-263-1888
Fax: 949-263-1338
San Jose
1300 Terra Bella Avenue
Mountain View, CA 94043
Tel: 650-215-1444
Fax: 650-961-0286
Toronto
6285 Northam Drive, Suite 108
Mississauga, Ontario L4V 1X5, Canada
Tel: 905-673-0699
Fax: 905-673-6509
ASIA/PACIFIC
Australia
Suite 22, 41 Rawson Street
Epping 2121, NSW
Australia
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Unit 28F, World Trade Plaza
No. 71 Wusi Road
Fuzhou 350001, China
Tel: 86-591-7503506
Fax: 86-591-7503521
China - Hong Kong SAR
Unit 901-6, Tower 2, Metroplaza
223 Hing Fong Road
Kwai Fong, N.T., Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
Singapore
Taiwan
Kaohsiung Branch
30F - 1 No. 8
Min Chuan 2nd Road
Kaohsiung 806, Taiwan
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Taiwan
Taiwan Branch
11F-3, No. 207
Tung Hua North Road
Taipei, 105, Taiwan
Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
EUROPE
China - Shanghai
Austria
Room 701, Bldg. B
Far East International Plaza
No. 317 Xian Xia Road
Shanghai, 200051
Tel: 86-21-6275-5700
Fax: 86-21-6275-5060
Denmark
China - Shenzhen
Rm. 1812, 18/F, Building A, United Plaza
No. 5022 Binhe Road, Futian District
Shenzhen 518033, China
Tel: 86-755-82901380
Fax: 86-755-8295-1393
China - Shunde
Room 401, Hongjian Building, No. 2
Fengxiangnan Road, Ronggui Town, Shunde
District, Foshan City, Guangdong 528303, China
Tel: 86-757-28395507 Fax: 86-757-28395571
China - Qingdao
Rm. B505A, Fullhope Plaza,
No. 12 Hong Kong Central Rd.
Qingdao 266071, China
Tel: 86-532-5027355 Fax: 86-532-5027205
India
Divyasree Chambers
1 Floor, Wing A (A3/A4)
No. 11, O’Shaugnessey Road
Bangalore, 560 025, India
Tel: 91-80-22290061 Fax: 91-80-22290062
Japan
Benex S-1 6F
3-18-20, Shinyokohama
Kohoku-Ku, Yokohama-shi
Kanagawa, 222-0033, Japan
Tel: 81-45-471- 6166 Fax: 81-45-471-6122
Durisolstrasse 2
A-4600 Wels
Austria
Tel: 43-7242-2244-399
Fax: 43-7242-2244-393
Regus Business Centre
Lautrup hoj 1-3
Ballerup DK-2750 Denmark
Tel: 45-4420-9895 Fax: 45-4420-9910
France
Parc d’Activite du Moulin de Massy
43 Rue du Saule Trapu
Batiment A - ler Etage
91300 Massy, France
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany
Steinheilstrasse 10
D-85737 Ismaning, Germany
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy
Via Quasimodo, 12
20025 Legnano (MI)
Milan, Italy
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands
P. A. De Biesbosch 14
NL-5152 SC Drunen, Netherlands
Tel: 31-416-690399
Fax: 31-416-690340
United Kingdom
505 Eskdale Road
Winnersh Triangle
Wokingham
Berkshire, England RG41 5TU
Tel: 44-118-921-5869
Fax: 44-118-921-5820
02/17/04
DS21823B-page 24
 2004 Microchip Technology Inc.