YAGEO NLC322522T-100K-N Specification for approval Datasheet

 Lead-Free & RoHs Compliance!!
SPECIFICATION FOR APPROVAL
CUSTOMER
CUSTOMER P/N
OUR DWG No
QUANTITY
ITEM
Pcs.
DATE
2010/11/01
NLC322522T-100K-N
SPECIFICATION
ACCEPTED BY:
COMPONENT
ENGINEER
ELECTRICAL
ENGINEER
MECHANICAL
ENGINEER
APPROVED
REJECTED
DRAWN BY
Sally
CHECKED BY
APPROVED BY
YG10B00061
NLC322522T Series Specification
1 Scope: This specification applies to Wire Wound Ferrite Chip Inductors
2 Part Numbering: Product Identification
3 Rating:
Operating Temperature: Storage Temperature: Under ,Humidity < 75% RH
4 Marking:
5 Standard Testing Condition
Unless otherwise specified
Temperature Ordinary Temperature(15 to 35)
Humidity
Ordinary Humidity(25 to 85% RH)
In case of doubt
20±2
60 to 70 % RH
NLC322522T Series Specification
6 Configuration and Dimensions:
7 ELECTRICAL CHARACTERISTICS
Part No.
Inductance
(uH)
L,Q Test Freq.
(MHZ)
Q
Min.
SRF
RDC
(MHz)Typ. ( )±30%
IDC
(mA)
Tolerance
(±%)
Color Code
3rd
1st
2nd
NLC322522T-R47 -N
0.47
25.2
40
450
0.07
1800
5,10
YEL
VIO
BRN
NLC322522T-1R0 -N
1
7.96
20
100
0.08
1500
5,10
BRN
BLK
RED
NLC322522T-1R2 -N
1.2
7.96
20
90
0.12
1400
5,10
BRN
RED RED
NLC322522T-1R5 -N
1.5
7.96
20
80
0.13
1125
5,10
BRN
GRN RED
NLC322522T-1R8 -N
1.8
7.96
20
70
0.13
970
5,10
BRN
GRY RED
NLC322522T-2R2 -N
2.2
7.96
20
68
0.13
970
5,10
RED
RED RED
NLC322522T-2R7 -N
2.7
7.96
20
62
0.15
900
5,10
RED
VIO RED
NLC322522T-3R3 -N
3.3
7.96
20
54
0.16
837
5,10
ORN
ORN RED
NLC322522T-4R7 -N
4.7
7.96
20
43
0.23
675
5,10
YEL
VIO RED
NLC322522T-5R6 -N
5.6
7.96
20
36
0.26
620
5,10
GRN
BLU RED
NLC322522T-6R8 -N
6.8
7.96
20
33
0.27
600
5,10
BLU
GRY RED
NLC322522T-8R2 -N
8.2
7.96
20
30
0.32
580
5,10
GRY
RED RED
NLC322522T-100 -N
10
2.52
15
28
0.36
520
5,10
BRN
BLK ORN
NLC322522T-120 -N
12
2.52
15
25
0.5
500
5,10
BRN
RED ORN
NLC322522T-150 -N
15
2.52
15
19
0.56
480
5,10
BRN
GRN ORN
NLC322522T-180 -N
18
2.52
15
17
0.67
330
5,10
BRN
GRY ORN
NLC322522T-220 -N
22
2.52
15
16
0.77
310
5,10
RED
RED ORN
NLC322522T-270 -N
27
2.52
15
13
1
280
5,10
RED
VIO ORN
NLC322522T-330 -N
33
2.52
15
12
1.1
270
5,10
ORN
ORN ORN
NLC322522T-390 -N
39
2.52
15
11
1.4
220
5,10
ORN
WHT ORN
NLC322522T-470 -N
47
2.52
15
10
1.64
210
5,10
YEL
VIO ORN
NLC322522T-560 -N
56
2.52
15
9
2.49
189
5,10
GRN
BLU ORN
NLC322522T-680 -N
68
2.52
15
9
2.8
189
5,10
BLU
GRY ORN
NLC322522T-820 -N
82
2.52
15
6
3
145
5,10
GRY
RED ORN
NLC322522T-101 -N
100
0.796
15
6
3.7
145
5,10
BRN
BLK
NOTE: -tolerance J=±5% / K=±10% M=±20%
1.Operating temperature range 2.IDC:Applied the current to coils, the inductance shall be less than 10% initial value.
"-N" FOR COMPLETELY LEAD FREE TYPE(INCLUDING FERRITE BODY & SOLDER)
YEL
NLC322522T Series Specification
Part No.
Inductance
(uH)
L,Q Test Freq.
(MHZ)
Q
Min.
SRF
RDC
(MHz)Typ. ( )±30%
IDC
(mA)
Tolerance
(±%)
Color Code
3rd
1st
2nd
NLC322522T-151 -N
150
0.796
15
5
6.1
120
5,10
BRN
GRN YEL
NLC322522T-181 -N
180
0.796
15
4
8
105
5,10
BRN
GRY YEL
NLC322522T-221 -N
220
0.796
15
4
8.4
100
5,10
RED
RED YEL
NLC322522T-331 -N
330
0.796
15
3.5
12.3
80
5,10
ORN
ORN YEL
NLC322522T-391 -N
390
0.796
15
2.8
17.6
75
5,10
ORN
WHT YEL
NLC322522T-471 -N
470
0.796
15
2.8
22
75
5,10
YEL
VIO YEL
NLC322522T-561 -N
560
0.796
15
2.5
23
65
5,10
GRN
BLU YEL
NLC322522T-681 -N
680
0.796
15
2
28
65
5,10
BLU
GRY YEL
NLC322522T Series Specification
8 NLC322522T Series
8.1 Construction:
8.2 Material List:
NLC322522T Series Specification
9 Reliability Of Ferrite Wire Wound Chip Inductor/FERRITE SERIES
1-1.Environmental Performance
No Item
Specification
1-1-1 Temperature Cycle
Appearance: No Damage
Inductance:within±10% of
initial value
Q change:within±30% of
initial value
1-1-2 Humidity Resistance
1-1-3 High Temperature Resistance
1-1-4 Low Temperature Resistance
1-1-5 High Temperature Load Life
There should be no evidence
of short or open circle
1-1-6 Humidity Load Life
1-2.Mechanical Performance
No Item
Specification
1-2-1 Resistance TO
Soldering Heat
Apperance: No Damage
1-2-2 Solder ability
The electrodes shall be
at least 95% covered
with new solder coating
1-2-3 Component
Adhesion
(Push Test)
2 Lbs. For NLC252018
4 Lbs. For NLC322522
Test Method
One cycle:
Step
Time (min)
Temperature ()
1
-25±3
30
2
25±2
3
3
85±3
30
4
25±2
3
Total: 5 cycles
Measured After Exposure in The Room Condition For 1hrs
Temperature: 40±2
Relative Humidity: 90 ~ 95%
Time: 100hrs
Measured After Exposure In The Room Condition For 1hrs
Temperature: 85±3
Time: 50Hrs
Measured After Exposure In The Room Condition For 1Hrs
Temperature: -25±3
Time: 50Hrs
Measured After Exposure In The Room Condition For 1Hrs
Temperature: 85±3
Load: Allowed DC Current
Time: 1000Hrs
Temperature: 40±2
Relative Humidity: 90~95%
Load: Allowed DC Current
Time: 1000Hrs
Test Method
1. The device should be reflow soldered on PCB
(peak 260 ±5 for 10 seconds)
2. Solder Composition: Sn/Ag3.0/Cu0.5
3. Test time: 6 minutes
1. Pre-Heating: 150 ,1min.
2. Solder Composition: Sn/Ag3.0/Cu0.5
3. Solder Temperature: 245±5 .
4. Immersion Time: 4±1 sec.
The device should be reflow soldered (245±5 For
10 seconds) to a tinned copper substrate. A force gauge
should be applied to the side of the component.
The device must withstand a minimum force of 1or2or4 pounds
without a failure of the termination attached to component
NLC322522T Series Specification
NLC322522T Series Specification
NLC322522T Series Specification
10 TEST DATA FOR PREPRODUCTION SAMPLES
QF-1419
DESCRIPTION: NLC322522T-100K-N
MEAS.
Item
L
(uH)
Spec Customer
10±10%
Suggest
Test Freq.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
X
R
Q
SRF
(MHz)
RDC
( )
IDC
(mA)
A
m/m
B
m/m
C
m/m
D
m/m
15-0
28TYP.
0.36±30%
520
3.7+0
2.9+0
2.6+0
0.51
2.52MHz
2.52MHz
9.78
23
55
0.422
OK
3.5
2.7
2.46
0.51
9.85
22
57
0.415
OK
3.56
2.67
2.42
0.51
9.88
25
63
0.409
OK
3.52
2.73
2.45
0.5
9.73
22
54
0.412
OK
3.52
2.71
2.44
0.51
9.91
21
52
0.42
OK
3.54
2.68
2.44
0.51
9.83
22.6
56.2
0.4156
3.528
2.698
2.442
0.508
0.18
4
11
0.013
0.06
0.06
0.04
0.01
E
m/m
CUSTOMER
SAMPLE
TEST INSTRUMENT:
HP4291A (over 1MHz) FOR L,Q
HP4285A (under 1MHz) FOR L,Q
CHEN HWA 502BC FOR RDC
HP4284A + HP4281A FOR IDC
HP4291A / HP8753D FOR SRF
APPEARANCE AND DIMENSIONS :
SPEC : MEET ITEM 6.
TEST METHOD : VISUAL INSPECTION AND MEASURED WITH SILDE CALIPERS.
TESTING CONDITIONS :
Temperature
Humidity
Unless otherwise specified
Ordinary Temperature (15 to 35)
Ordinary Humidity (25 to 85 %RH)
ln case of doubt
20 ± 2 60 to 70 %RH
NLC322522T Series Specification
11 PACKAGING
11.1 Packaging -Cover tape
The force for tearing off cover tape is 10 to 130 grams in the arrow direction.
11.2 Packaging Quantity
11.3 Reel Dimensions
NLC322522T Series Specification
11 PACKAGING
11.4 Tape Dimensions in mm
12 Recommended Pattern
13 Note:
1. Please make sure that your product is has been evaluated and confirmed against your specifications
when our product is mounted to your product.
2. Do not knock nor drop.
3. All the items and parameters in this product specification have been prescribed on the premise that
our product is used for the purpose,under the condition and in the environment agreed upon between
you and us. You are requested not to use our product deviating from such agreement.
4. Please keep the distance between transformer/coil and other components (refer to the standard IEC 950)
NLC322522T Series Specification
14 Curve:
Similar pages