STANDARD Resistive Touch Panel Specification FID-550 7-Wire Series Input Panel Panel Drive change over switch Noise Filter MCU Interface Control Section A/D converter ■ FEATURES • Superior long life, using a unique construction method offering improved life over typical technologies; by sensing data input only on the glass layer, typically a 10x improvement in product life is achived. • Excellent specification and high quality - Anti-Newton ring technology - High reliability materials • Pen/Finger, Pen Only, Finger Only, Light Touch types available • Transparency 80% - typical ■ PART NUMBERS Controller Boards: ■ PART NUMBERS Touch Panels: Part Number Size Type Part Number Type N010-0510-T302 17" Pen/Finger N16B-0558-B240 7-Wire, RS232 N010-0510-T211 15" Pen/Finger N16B-0558-B720 7-Wire, USB N010-0550-T913 13.3" Pen/Finger N010-0550-T711 12.1" Pen/Finger N010-0551-T242 12.1" Pen/Finger (light touch type) N010-0550-T811 11.3 Pen/Finger N010-0550-T601 10.4" Pen only N010-0550-T611 10.4" Pen/Finger N010-0550-T621 10.4" Pen/Finger (light touch type) N010-0550-T511 9.5" Pen/Finger N010-0550-T341 8.4" Pen/Finger ■ PART NUMBERS Interface Controller Chips: Part Number Type N010-0559-V022 7-Wire, RS232 NC41120-0015 7-Wire, USB FID-550 SERIES ■ DIMENSION EXAMPLE (10.4” SHOWN) (3.50) (11.50) 2.0 ± ±1.0 243.80 236.80 217.10 (transparent ( area)) 215.10 213.10 (input ( area)) ±1.0 23.20 Top 90.5±1.0 ± 1 ( (8.00) 22.00 16.00 Left 7 187.40 180.40 164.40 (transparent area) 162.40 160.40 (input ( area)) 47.0 x 3=141.00 47.00 93.70 ± 3.50 1 12.5 0.5 ±1.0 123.75 (3.50) Unit: mm Bottom ■ DETAILED SPECIFICATION ■ 1.0 APPLICATION This specification applies to the 10.4" (inch) standard Touch Panel (Pen/Finger type). P/N is N010-0550-T611. ■ 2.0 ADDITIONAL APPLICATIONS Control IC specifications and Control PCB, complete Touch Panel Specifications are also applicable. ■ 3.0 DISCRIPTION AND BLOCK DIAGRAM This panel in combination with a control IC chip is used to transfer the co-ordinates of the touched position to the host system (see block diagram above). ■ 4.0 DRAWING (Please see the diagram above.) Definitions of the major dimensions indicated on this diagram: Effective Input Area (A) Area guaranteed to meet all the characteristics detailed in this specification View / Transparent Area (B) The area inside the adhesive zone or electrode pattern. Anti-input Area (C) An insulating area allowed to protect the touch panel from giving false readings when an enclosure touches the panel. ■ 5.0 CHARACTERISTICS ■ 5.1 MECHANICAL Operating Force 0.05~0.49 N (5 ~ 50gF) Measured with a Silicon Measurement Rod R 8 (Round type 8mm) Silicon Rubber Hardness 60˚C Hardness of Surface Pencil hardness 3H minimum against specification JIS K-5400 ■ 5.2 OPTICAL Transparency Haze A B C Force Silicon Rubber Rod 78% min measured in the effective input area to JIS K 7105 using a MURAKAMI SHIKISAI KENKYUSHO type IIR 100 meter. Typically 80%. 5% measured in the effective input area using a MURAKAMI SHIKISAI KENKYUSHO type IIR 100 meter with an Anti Glare treated surface. 2 FID-550 SERIES ■ 5.3 ELECTRICAL Location Accuracy: Linearity: Current Consumption: Switch Bounce (Chattering): Insulation resistance: Dielectric Strength: ±2.5mm Measured over 9 points (See note 1) 1.5% 20mA max at DC 5V when applying 5VDC between pins 3 & 5 10ms min when using the silicon rubber measurement rod. 10MΩ minimum at 25KV DC applied between pins 3 & 7 or between 5 and 7 25KV DC for 1 minute Measurement condition of linearity is corrected within the control IC. In general the location accuracy is specified as follows: Actual co-ordinate point - theoretical co-ordinate point = location accuracy. In general a 9 point co-ordinate calibration system is used to adjust the micro controller accuracy. (20 point can be used in combination with an EEPROM design). Note 2: Co-ordinate Point Note 1: Theoretical Error Actual Distance Pins 3, 5 and 7 are the glass and film connection points. 5.4 ENVIRONMENTAL Operating Temperature (*): Storage Temperature: Operating Humidity: Storage Humidity: Chemical Resistance: ■ -5˚C to 60˚C -30˚C to 70˚C 20% to 90% RH with a Maximum wet bulb temperature of 38˚C 10% ~ 90% RH with a Maximum wet bulb temperature of 38˚C Coating with the following chemicals and storing at room temperature for 2 hours gives no problems. 10% NaCl-water solution, ethyl-acetate, ethylalcohol, toluene, methyl-ethyl-ketone. 5.5 PEN LIFE Character Writing life: Touch Input life : 1,000,000 words minimum 10,000,000 times minimum Note 1: Words are written in the notes area and the size of the word is 7.5mm x 6.75mm. A word is any Alphabet / Number / Mark. The pen is as shown below and applies a force of 250g. A failure is judged to happen when the current consumption or insulation resistance or dielectric strength are not met as shown in 5.3. The location accuracy with 9 point calibration must be ±4.4 mm max. Effective input area Notes 10 mm ■ 1.0 Ø2.0 8 Ø6.0 .0 9.0 0. Ø2 R 3.0 3.5 Ø 4.6 9 mm 1.5 110.0±1.0 3 FID-550 SERIES ■ 5.6 FINGER LIFE A finger is simulated by a silicon rubber plunger R8 (Round type 8mm size) hardness 60˚C at 200g at frequency 5Hz. A failure is judged to happen when the current consumption or insulation resistance or dielectric strength are not met as shown in 5.3. The location accuracy with 9 point calibration must be ±4.4 mm max. Typical operating force is 150g max. ■ 5.7 INFORMATION ON THE PANEL The panel part number is visible from the film side The production information is visible from the glass side. Production year 99 00 etc. 1 2 3 4 5 6 7 8 9 X Y Z or 1 2 3 4 5 6 7 8 9 X Y Z 2 3 4 5 6 7 8 9 X Y Z or 23456789XYZ Z or 1 2 3 4 5 6 7 8 9 ■ ■ YZ January Production February Production December Production 6 PACKAGING 6.1 PACKING SPECIFICATION Vibration: 10~55 Hz at 1 Octave per minute 10G 20 cycles with one side 0.75mm Drop test: 60cm Drop 1 corner, 3 crease lines and 6 faces. 1 each 1 time After the test no glass: flaw or crack is seen, and no dent or scratch on the film. Also glass and film must not separate. ■ 6.1 PACKING DETAILS Each touch panel is placed into a plastic bag and is held in place by a slit cut into the side of the cardboard. A second insertion piece is placed into the carton to again add stability. The qty is written on the side of the box. For example the T611 has 26 pieces per box. Insert Touch panel with bag Slit in cardboard 4 FID-550 SERIES ■ 7.0 REJECT CRITERIA Description Area ≥ 0.1mm2 Area ≥ 0.05mm2 & area < 0.1mm2 Area < 0.05mm2 : to be zero : to be max. 5 points : none specified Dot type Area > 0.1mm2 Area ≥ 0.05mm2 & area < 0.1mm2 Area < 0.05mm2 : to be zero : to be max. 5 points : none specified Line type Area ≥ 0.1mm Area ≥ 0.03mm & width <0.1mm and length < 10mm Area < 0.05mm : to be zero : to be max. 1 point : none specified Film Dent Foreign material between glass and film Reject Criteria Scratch Dot blur or hard coat missing Newton Ring Glass flaw Area ≥ 0.1mm : to be zero Area ≥ 0.03mm & width <0.1mm with length < 80mm : to be max. 1 point Area < 0.03mm & width <0.1mm with length < 30mm : none specified Area ≥ 0.5mm2 Area ≥ 0.03mm2 & area < 0.5mm2 Area < 0.05mm2 : to be zero : to be max. 5 points : none specified These must not be seen from Panel film side under a fluorescent lamp (3 wavelength type lamp). Not to be verified form glass side. To be no flaw which is bigger than that shown in the following diagram. The number of flaws is not specified. 3mm 5mm 2mm 2mm ■ 8.0 GENERAL POINTS OF CAUTION Touch panels are made of glass, so care must be taken in handling them. Do not stress, pile, bend, lift by the cable or put any stress on the film, for example moving by film face vacuum. In order to clean wring dry a cloth which has been emersed in a natural detergent. DO NOT use any organic solvent, acid or alkali solution. Watch the edge of the panel when cleaning, again for safety reasons. 5 FID-550 SERIES ■ 9.0 CONNECTION AND MOUNTING The details below indicate the recommended mounting structure for panel and enclosure. The enclosure support to fix the touch panel must be over 1.0mm I width and must be outside the view (Transparent area). Also ensure that the enclosure does not cause miss input by touching the view area. The following diagram shows that the enclosure edge must be between the View area and the guaranteed active area. Ensure space is allocated for the diodes, and we recommend that the material to fix the panel and enclosure is elastic. Special design would be required to stop water ingress. The corners of the touch panel are conductive so do not touch any metal parts after mounting. Detect Right/ Upper Right/ Upper Each side Left/ Lower Each side Left/ Lower All Film Glass Glass Glass Glass Glass Glass 0.7 2.0 3.35 2.0 Laminate Film Conductive Face FPC-type cable 0.3±0.05 Stiffener Board 1.2 1.1 1. 2. 3. 4. 5. 6. 7. Location Top View (Picture, with conductive side down) Contact Section View Bottom View (Drawing, with conductive side up) (Mating connector type FCI or equivalent SFW15R-1ST: for FPC) Transparent Area Anit-input Area 0.8 mm min. Cut-out / avoidance of 550 surface mount diodes Input Area Upper Case Shock absorber to protect the panel (eg rubber) Input Panel Wiring Area 0.3 to 0.1 mm View Area LCD Shock absorber for protection Connector Circuit Board 6 FID-550 SERIES ■ 10.0 PANEL THICKNESS 1.4 2.6 Max Stiffener Board Fujitsu Components International Headquarter Offices Thickness of glass 1.1mm Conductive Face Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: www.fceu.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: www.fcai.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 375-8560 Fax: (65) 273-3021 Email: [email protected] www.fcal.fujitsu.com © 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 11/02/2004. 7