Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type for Large Current Data Sheet 1 Common Mode Choke Coil Wire Wound Type for Large Current DLW5BT Series (2020 Size) c Dimensions c Impedance-Frequency Characteristics (Main Items) Polarity Marking 10000 * The marking to indicate the product direction can be applicable. (Optional) Common mode DLW5BTN142SQ2 DLW5BTN102SQ2 1000 1.7±0.3 (1) (4) (2) (3) (L) 5.0±0.3 Impedance (Ω) (W) 5.0±0.3 (T) 2.35±0.15 0.5 min. 1.3±0.3 1.7±0.3 3.6±0.3 0.45 min. DLW5BTN501SQ2 DLW5BTN251SQ2 10 DLW5BTN101SQ2 DLW5BTN251SQ2 DLW5BTN501SQ2 DLW5BTN102SQ2 DLW5BTN142SQ2 Differential mode 1 : Electrode 1.3±0.3 0.9±0.3 DLW5BTN101SQ2 100 1 10 100 1000 Frequency (MHz) (in mm) c Equivalent Circuit c Packaging (1) (2) (4) (3) Code Packaging L 180mm Embossed Tape Minimum Quantity 700 K 330mm Embossed Tape 2500 B Bulk(Bag) 100 No polarity. c Rated Value (p: packaging code) Part Number Operating Common Mode Impedance Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance Temperature Range (at 100MHz/20°C) DLW5BTN101SQ2p 100ohm (Typ.) 6000mA 50Vdc 10M ohm 125Vdc 0.009ohm±40% -40 to +85°C DLW5BTN251SQ2p 250ohm (Typ.) 5000mA 50Vdc 10M ohm 125Vdc 0.014ohm±40% -40 to +85°C DLW5BTN501SQ2p 500ohm (Typ.) 4000mA 50Vdc 10M ohm 125Vdc 0.019ohm±40% -40 to +85°C DLW5BTN102SQ2p 1000ohm (Typ.) 2000mA 50Vdc 10M ohm 125Vdc 0.024ohm±40% -40 to +85°C DLW5BTN142SQ2p 1400ohm (Typ.) 1500mA 50Vdc 10M ohm 125Vdc 0.040ohm±40% -40 to +85°C Number of Circuit: 1 Continued on the following page. oThis data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2012.3.1 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type for Large Current Data Sheet 2 Continued from the preceding page. c Derating of Rated Current In operating temperature exceeding +60°C, derating of current is necessary for the following part name of DLW5BT series. Please apply the derating curve shown in chart according to the operating temperature. Derating of Rated Current 7000 Rated Current (mA) 6000 5000 4750 4000 3400 3000 DLW5BTN101SQ2 DLW5BTN251SQ2 DLW5BTN501SQ2 2000 1000 0 0 20 40 60 65 80 85 100 Operating Temperature (°C) c !Caution/Notice !Caution (Rating) Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. oThis data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2012.3.1 http://www.murata.com/