Gamma GM1117S-2.85TB3T 1a low dropout precision voltage regulator Datasheet

GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Description
Features
The GM1117S is a positive low dropout
regulator and is available in an adjustable
version and fixed output voltage from 1.5V to
5.0V. All internal circuitry is designed to
operate down to 800mV input to output
differential and the dropout voltage is fully
specified as a function of load current. On chip
trimming adjusts the reference/output voltage
to within ± 1%. Current limit is also trimmed in
order to minimize the stress on both the
regulator and the power source circuitry under
overloaded conditions.
‹
Adjustable or Fixed Output
‹
Output Current of 1.0A
‹
Dropout Voltage 1.5V max @ 1.0A
‹
Line Regulation 0.2% max.
‹
Load Regulation 0.4% max.
‹
Fast Transient Response
‹
Current Limit Protection
‹
Thermal Shutdown Protection
Application
High Efficiency Linear Regulators
Battery Powered Equipment
Post Regulators for Switching Supplies
Reference Voltage Sources
Microprocessor Supply
Hard Drive Controllers
Battery Chargers
Adjustable Power Supply
Typical Application Circuits
VOUT
GM1117S
R1
133Ω
C2
C1
10µF
VOUT
R2
232Ω
10µF
Adjustable Regulator
R2
=1.25V
( 1+
R1
VIN
VOUT
GM1117S-x.x
C1
10µF
C2
10µF
Fixed Output Voltage Regulator
)
GM1117SV2.03
VIN
1
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Marking Information and Pin Configurations (Top View) – Pb Free
TO 252
(D-PAK)
TO 220
TO 263
(D2-PAK)
GM1117S
VVAYWW
SOT223
GM1117S
VVAYWW
GM1117S
VVAYWW
3. VIN
2. VOUT
3. VIN
2. V
OUT
1. Gnd/Adj
1. Gnd/Adj
3. VIN
2. VOUT
1. Gnd/Adj
GM1117S
VVAYWW
3. V
IN
2. VOUT
1. Gnd/Adj
VV: Voltage suffix (15 = 1.5V, 50 = 5.0V…A = Adj)
A: Assembly / Test site code
Y: Year
WW: Week
Marking Information and Pin Configurations (Top View) – Green
TO 252
(D-PAK)
TO 220
TO 263
(D2-PAK)
GM1117SG
VVAYWW
GM1117SV2.03
3. VIN
3. VIN
2. VOUT
1. Gnd/Adj
3. VIN
2. VOUT
1. Gnd/Adj
G: Green Product
VV: Voltage suffix (15 = 1.5V, 50 = 5.0V…A = Adj)
A: Assembly / Test site code
Y: Year
WW: Week
2. VOUT
GM1117SG
VVAYWW
GM1117SG
VVAYWW
1. Gnd/Adj
3. VIN
2. VOUT
1. Gnd/Adj
2
GM1117SG
VVAYWW
SOT223
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Package
Shipping
GM1117S-AST3T
SOT-223
80 Units/Tube
GM1117S-AST3R
SOT-223
2,500 Units / Tape & Reel
GM1117S-ATC3T
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-ATB3T
TO-220
50 Units/Tube
GM1117S-ATA3T
TO-263
50 Units/Tube
GM1117S-ATA3R
TO-263
800 Units / Tape & Reel
GM1117S-1.5ST3T
SOT-223
80 Units/Tube
GM1117S-1.5ST3R
SOT-223
2,500 Units / Tape & Reel
GM1117S-1.5TC3T
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-1.5TB3T
TO-220
50 Units/Tube
GM1117S-1.5TA3T
TO-263
50 Units/Tube
GM1117S-1.5TA3R
TO-263
800 Units / Tape & Reel
GM1117S-1.8ST3T
SOT-223
80 Units/Tube
GM1117S-1.8ST3R
SOT-223
2,500 Units / Tape & Reel
GM1117S-1.8TC3T
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-1.8TB3T
TO-220
50 Units/Tube
GM1117S-1.8TA3T
TO-263
50 Units/Tube
GM1117S-1.8TA3R
TO-263
800 Units / Tape & Reel
GM1117S-2.5ST3T
SOT-223
80 Units/Tube
GM1117S-2.5ST3R
SOT-223
2,500 Units / Tape & Reel
GM1117S-2.5TC3T
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-2.5TB3T
TO-220
50 Units/Tube
GM1117S-2.5TA3T
TO-263
50 Units/Tube
GM1117S-2.5TA3R
TO-263
800 Units / Tape & Reel
Ordering Number
GM1117S-ATC3R
GM1117S-1.5TC3R
GM1117S-1.8TC3R
GM1117S-2.5TC3R
Output Voltage
Adj
1.5V
1.8V
2.5V
GM1117SV2.03
Ordering Information – Pb Free Products
3
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Ordering Information – Pb Free Products (Continued)
Package
Shipping
GM1117S-2.85ST3T
SOT-223
80 Units/Tube
GM1117S-2.85ST3R
SOT-223
2,500 Units / Tape & Reel
GM1117S-2.85TC3T
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-2.85TB3T
TO-220
50 Units/Tube
GM1117S-2.85TA3T
TO-263
50 Units/Tube
GM1117S-2.85TA3R
TO-263
800 Units / Tape & Reel
GM1117S-3.0ST3T
SOT-223
80 Units/Tube
GM1117S-3.0ST3R
SOT-223
2,500 Units / Tape & Reel
GM1117S-3.0TC3T
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-3.0TB3T
TO-220
50 Units/Tube
GM1117S-3.0TA3T
TO-263
50 Units/Tube
GM1117S-3.0TA3R
TO-263
800 Units / Tape & Reel
GM1117S-3.3ST3T
SOT-223
80 Units/Tube
GM1117S-3.3ST3R
SOT-223
2,500 Units / Tape & Reel
GM1117S-3.3TC3T
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
TO-220
50 Units/Tube
GM1117S-3.3TA3T
TO-263
50 Units/Tube
GM1117S-3.3TA3R
TO-263
800 Units / Tape & Reel
GM1117S-5.0ST3T
SOT-223
80 Units/Tube
GM1117S-5.0ST3R
SOT-223
2,500 Units / Tape & Reel
GM1117S-5.0TC3T
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-5.0TB3T
TO-220
50 Units/Tube
GM1117S-5.0TA3T
TO-263
50 Units/Tube
GM1117S-5.0TA3R
TO-263
800 Units / Tape & Reel
Ordering Number
GM1117S-2.85TC3R
GM1117S-3.0TC3R
GM1117S-3.3TC3R
Output Voltage
2.85V
3.0V
3.3V
GM1117S-3.3TB3T
GM1117SV2.03
GM1117S-5.0TC3R
4
5.0V
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Package
Shipping
GM1117S-AST3TG
SOT-223
80 Units/Tube
GM1117S-AST3RG
SOT-223
2,500 Units / Tape & Reel
GM1117S-ATC3TG
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-ATB3TG
TO-220
50 Units/Tube
GM1117S-ATA3TG
TO-263
50 Units/Tube
GM1117S-ATA3RG
TO-263
800 Units / Tape & Reel
GM1117S-1.5ST3TG
SOT-223
80 Units/Tube
GM1117S-1.5ST3RG
SOT-223
2,500 Units / Tape & Reel
GM1117S-1.5TC3TG
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-1.5TB3TG
TO-220
50 Units/Tube
GM1117S-1.5TA3TG
TO-263
50 Units/Tube
GM1117S-1.5TA3RG
TO-263
800 Units / Tape & Reel
GM1117S-1.8ST3TG
SOT-223
80 Units/Tube
GM1117S-1.8ST3RG
SOT-223
2,500 Units / Tape & Reel
GM1117S-1.8TC3TG
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-1.8TB3TG
TO-220
50 Units/Tube
GM1117S-1.8TA3TG
TO-263
50 Units/Tube
GM1117S-1.8TA3RG
TO-263
800 Units / Tape & Reel
GM1117S-2.5ST3TG
SOT-223
80 Units/Tube
GM1117S-2.5ST3RG
SOT-223
2,500 Units / Tape & Reel
GM1117S-2.5TC3TG
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-2.5TB3TG
TO-220
50 Units/Tube
GM1117S-2.5TA3TG
TO-263
50 Units/Tube
GM1117S-2.5TA3RG
TO-263
800 Units / Tape & Reel
Ordering Number
GM1117S-ATC3RG
GM1117S-1.5TC3RG
GM1117S-1.8TC3RG
GM1117S-2.5TC3RG
Output Voltage
Adj
1.5V
1.8V
2.5V
GM1117SV2.03
Ordering Information – Green Products
5
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Ordering Information – Green Products (Continued)
Package
Shipping
GM1117S-2.85ST3TG
SOT-223
80 Units/Tube
GM1117S-2.85ST3RG
SOT-223
2,500 Units / Tape & Reel
GM1117S-2.85TC3TG
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-2.85TB3TG
TO-220
50 Units/Tube
GM1117S-2.85TA3TG
TO-263
50 Units/Tube
GM1117S-2.85TA3RG
TO-263
800 Units / Tape & Reel
GM1117S-3.0ST3TG
SOT-223
80 Units/Tube
GM1117S-3.0ST3RG
SOT-223
2,500 Units / Tape & Reel
GM1117S-3.0TC3TG
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-3.0TB3TG
TO-220
50 Units/Tube
GM1117S-3.0TA3TG
TO-263
50 Units/Tube
GM1117S-3.0TA3RG
TO-263
800 Units / Tape & Reel
GM1117S-3.3ST3TG
SOT-223
80 Units/Tube
GM1117S-3.3ST3RG
SOT-223
2,500 Units / Tape & Reel
GM1117S-3.3TC3TG
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
TO-220
50 Units/Tube
GM1117S-3.3TA3TG
TO-263
50 Units/Tube
GM1117S-3.3TA3R
TO-263
800 Units / Tape & Reel
GM1117S-5.0ST3TG
SOT-223
80 Units/Tube
GM1117S-5.0ST3RG
SOT-223
2,500 Units / Tape & Reel
GM1117S-5.0TC3TG
TO-252
80 Units/Tube
TO-252
2,500 Units / Tape & Reel
GM1117S-5.0TB3TG
TO-220
50 Units/Tube
GM1117S-5.0TA3TG
TO-263
50 Units/Tube
GM1117S-5.0TA3RG
TO-263
800 Units / Tape & Reel
Ordering Number
GM1117S-2.85TC3RG
GM1117S-3.0TC3RG
GM1117S-3.3TC3RG
Output Voltage
2.85V
3.0V
3.3V
GM1117S-3.3TB3TG
GM1117SV2.03
GM1117S-5.0TC3RG
6
5.0V
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Absolute Maximum Ratings
PARAMETER
SYMBOL
RATINGS
UNITS
Input Voltage
VIN
15
V
SOT-223
Thermal Resistance,
Junction to Case
TO-252 (D PAK)
15.0
ӨJC
TO-263 (D2 PAK)
6.0
°C/W
3.0
Operating Junction Temperature
TJ
0 to 125
°C
Storage Temperature
Tstg
- 40 to 125
°C
Block Diagram
VIN
VOUT
GND
GM1117SV2.03
ADJ
For
fixed
output
Options
7
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Electrical Characteristics (TA = 25℃, unless otherwise noted)
Parameter
Reference
Voltage
GM1117S-Adj
Symbol
VREF
GM1117S-1.8
GM1117S-2.5
Output Voltage
VOUT
GM1117S-3.3
GM1117S-5.0
Condition
Min
Typ
Max
IOUT =10mA, VIN = 5V
1.238
1.250
1.262
10mA ≤ IOUT ≤ 1.0A,
2.65V ≤ VIN ≤ 10V
1.225
1.250
1.275
IOUT =10mA, VIN = 3.3V
1.782
1.800
1.818
10mA ≤ IOUT ≤ 1.0A,
3.3V ≤ VIN ≤ 10V
1.764
1.800
1.836
IOUT =10mA, VIN = 4V
2.475
2.500
2.525
10mA ≤ IOUT ≤ 1.0A,
4V ≤ VIN ≤ 10V
2.450
2.500
2.550
IOUT =10mA, VIN = 4.8V
3.267
3.300
3.333
10mA ≤ IOUT ≤ 1.0A,
4.8V ≤ VIN ≤ 10V
3.234
3.300
3.366
IOUT =10mA, VIN = 6.5V
4.950
5.000
5.050
10mA ≤ IOUT ≤ 1.0A,
6.5V ≤ VIN ≤ 10V
4.900
5.000
5.100
Unit
V
V
Line Regulation
∆VOI
IOUT =10mA,
1.5V ≤ VIN - Vout ≤ 10V
0.04
0.2
%
Load Regulation
∆VOL
VIN = VOUT + 1.5V
10mA ≤ IOUT ≤ 1.0A
0.2
0.4
%
Dropout Voltage
∆V
IOUT =1A
1.3
1.5
V
Current Limit
ICL
VIN = VOUT + 1.5V
1.5
2.0
A
Quiescent Current (Fixed Output
Voltage Versions)
IQ
VIN = VOUT + 1.5V
10mA ≤ IOUT ≤ 1.0A
3.5
10
mA
Adjust Pin
Current
IAdj
IOUT =10mA,
2.75V ≤ VIN ≤ 7V
40
90
µA
VIN = VOUT + 1.5V
IOUT = 10mA
0.005
%/℃
0.003
%/W
65
dB
GM1117S-Adj
Temperature Coefficient
TC
TA=25°C, 30ms pulse
Ripple Rejection
RA
VIN = VOUT + 1.5V
IOUT = 1A
60
GM1117SV2.03
Thermal Regulation
1.0
8
1
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Typical Performance Characteristics
0.10
0.08
TCASE = 25°C
0.95
VDROPOUT
Output Voltage Deviation (%)
TCASE = 0°C
0.90
0.85
TCASE = 125°C
0.80
0.75
0
200
400
600
0.04
0.02
0.00
-0.02
-0.04
-0.06
-0.08
-0.10
-0.12
0
1000
800
0.06
20
40
IOUT (mA)
60
80
100
120
TJ (°C)
Figure 2. Reference Voltage vs. Temperature
Figure 1. Dropout Voltage vs. Output Current
85
70
75
IO = 10mA
65
Ripple Rejection
60
55
50
45
40
0
55
45
35
25
10 20
30
40
50
60
70
80
90
15
100 110 120 130
Temperature (°C)
3.5
200
3.3
102
103
104
105
106
Frequency (Hz)
3.1
100
2.9
0
2.7
-100
2.5
VOUT= 3.3V
COUT= CIN = 22µF, Tantalum
CAdj = 0.1µF
-200
ISC (A)
Load Step (mA) Voltage Deviation(mV)
300
2.3
2.1
1000
1.9
500
1.7
1
2
3
4
5
6
7
Figure 5. Transient Response
6
101
Figure 4. Ripple Rejection vs. Frequency
Figure 3. Adjust Pin Current vs. Temperature
0
0
TCASE = 125°C
IO = 10mA
VIN = VOUT + 3V
VRIPPLE = 1.0VP-P
CADJ = 0.1µF
8
9
10
Time (µs)
1.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
VIN – VOUT (V)
Figure 6. Short Circuit Current vs. VIN -VOUT
GM1117SV2.03
Adjust Pin Current (µA)
65
9
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Application Notes
GM1117S linear regulators provide fixed and adjustable output voltage at current up to 1.0A. These
regulators are protected against over current conditions and include thermal shutdown protection.
The GM1117S has a composite PNP-NPN output transistor and require an output capacitor for
stability. A detailed procedure for selecting this capacitor follows.
Adjustable Operation
The GM1117S has an output voltage range for 1.25V to 5.5V. An external resistor divider sets the
output voltage as show in Figure 1. The regulator maintains a fixed 1.25V (typical) reference
between the output pin and the adjust pin. A resistor divider network R1 and R1 causes a fixed
current to follow to ground. This current creates a voltage across R2 that adds to the 1.25V across
R1 and sets the overall output voltage. The adjust pin current (typically 50µA) also flows through R2
and adds a small error that should be taken into account if precise adjustment of VOUT is necessary.
GM1117S
VIN
VIN
C1
VOUT
Adj
VOUT
VREF R1
C2
IADJ
VOUT
=1.25V
(
1+
R2
R1
CADJ
R2
)
Figure 1. Resistor Divider Scheme
The term IADJ X R2 represents the error added by the adjust pin current. R1 is chosen such that the
minimum load current is at least 2mA. R1 and R2 should be the same type, e.g., metal film for best
tracking over temperature. While not require, a bypass capacitor from the adjust pin to ground will
improve ripple rejection and transient response. A 0.1µF tantalum capacitor is recommended.
GM1117SV2.03
Stability Considerations
10
The output compensation capacitor helps to determine three feature characteristics of a linear
regulator's performance: start-up delay, load transient response, and loop stability. The capacitance
and type is based on cost, availability, size and temperature constraints. A tantalum or aluminum
electrolytic capacitor is preferred, as a film or ceramic capacitor with almost zero ESR can cause
instability. An aluminum electrolytic capacitor is the least expensive type, but when the circuit
operates at low temperatures, both the capacitance and ESR will vary widely. For optimum
performance over the full operating temperature range, a tantalum capacitor is best. A 22µF
tantalum capacitor will work fine in most applications, but with high current regulators such as the
GM1117S higher capacitance values will improve the transient response and stability. Most
applications for the GM1117S involve large changes in load current, so the output capacitor must
supply instantaneous load current. The ESR of the output capacitor causes an immediate drop in
output voltage given by:
△V = △I X ESR
In microprocessor applications, an output capacitor network of several tantalum and ceramic
capacitors in parallel is commonly used. This reduces overall ESR and minimizes the instantaneous
output voltage drop under transient load conditions. The output capacitor network should be placed
as close to the load as possible.
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Heatsink Requirements
When an integrated circuit operates with an appreciable current, its junction temperature is elevated.
It is important to consider its thermal limits in order to achieve acceptable performance and reliability.
This limit is determined by summing the individual parts consisting of a series of temperature rises
from the semiconductor junction to the operating environment.
The heat generated at the device junction flows through the die to the die attach pad, through the
lead frame to the surrounding case material, to the printed circuit board, and eventually to the
ambient environment. Below is a list of variables that may affect the thermal resistance and in turn
the need to a heatsink.
ΘJC, Junction to Case Thermal Resistance
ΘCA, Case to Ambient Thermal Resistance
1.
Lead Frame Size & Material
1.
Mounting Pad Size, Material & Location
2.
Number of conducting Pins
2.
Placement of Mounting Pad
3.
Die Size
3.
PCB Size & Material
4.
Die Attach Material
4.
Traces Length & Width
5.
Molding Compound Size & Material
5.
Adjacent Heat Source
6.
Volume of Air
7.
Ambient Temperature
8.
Shape of Mounting Pad
The GM1117S regulators have internal thermal shutdown to protect the device from over heating.
Under all possible operating conditions, the junction temperature of the GM1117S must be within in
the range of 0°C to 125°C. A heatsink may be required depending on the maximum power
dissipation and maximum ambient temperature of the application. To determine if a heatsink is
needed, the power dissipated y the regulator, PD, must be calculated according to the circuit below:
IIN
VIN
GM1117S
VIN
VOUT
LOAD
Gnd
VOUT
IIN = IL + IG
PD = (VIN – VOUT) X IL + VIN X IG
IL
IG
The next parameter which must be calculated is the maximum allowable temperature rise, TR(max):
TR(max) = TJ(max) – TA(max)
Using the calculated values for TR(max) and PD the maximum allowable value for the junction-to-ambient
thermal resistance (θJA) can be calculated:
ΘJA(max) = TR(max) X PD
If the maximum allowable value for ΘJA is found to be > 136°C/W for SOT223 packages or > 79°C/W
for TO220 package or > 92°C/W for TO252 package, no heat sink is needed since the package
alone will dissipate enough heat to satisfy these requirements. If the calculated value for ΘJA falls
below these limits, a heat sink is required.
GM1117SV2.03
Where TJ(max) is the maximum allowable junction temperature (125°C) and TA(max) is the maximum
ambient temperature which will be encountered in the application.
11
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
As a design aid, the table below shows the value of the ΘJA of SOT-223 and TO-252 for different
heat sink area.
Layout
Copper Area
2
* Top Side (in )
Bottom Side (in )
(ΘJA, °C/W) SOT-223
(ΘJA, °C/W) TO-252
1
0.0123
0
136
103
2
0.066
0
123
87
3
0.3
0
84
60
4
0.53
0
75
54
5
0.76
0
69
52
6
1
0
66
47
7
0
0.2
115
84
8
0
0.4
98
70
9
0
0.6
89
63
10
0
0.8
82
57
11
0
1
79
57
12
0.066
0.066
125
89
13
0.175
0.175
93
72
14
0.284
0.284
83
61
15
0.392
0.392
75
55
16
0.5
0.5
70
53
GM1117SV2.03
* Tab of device attached to top side copper.
12
Thermal Resistance
2
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Package Outline Dimensions – SOT223
0.248 - 0.264
(6.30 - 6.71)
0.010 - 0.014
(0.25 - 0.36)
0.116 - 0.124
(2.95 - 3.15)
0.130 - 0.146
(3.30 - 3.71)
0.264 - 0.287
(6.71 - 7.29)
10°- 16
°
0.071
(1.8)
MAX
0.0008 - 0.0040
(0.0203 - 0.1016)
10 - 16 °
0.012
(0.31)
0.090
(2.29)
0.033 - 0.041
(0.84 - 1.04)
NOM
MIN
°
0.025 - 0.033
(0.64 - 0.84)
0.81
(4.6)NOM
10°
MAX
NOM
Package Outline Dimensions – TO252
0.205 – 0.215
(5.210 – 5.460)
0.039 – 0.050
(1.020 – 1.270)
0.055 – 0.080
(1.400 – 2.030)
0.018 – 0.023
(0.460 – 0.580)
SEATING PLAN
0.370 – 0.410
(9.400 – 10.420)
0.090
(2.285)
TYP
0.180
(4.570)
TYP
0.045 – 0.060
(1.150 – 1.520)
0.030 – 0.045
(0.760 – 1.140)
0.020
(0.510)
MIN
0.018 – 0.023
(0.460 – 0.580)
GM1117SV2.03
0.210 – 0.228
(5.330 – 5.800)
13
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Package Outline Dimensions – TO263
0.390 - 0.415
(9.906 - 10.541)
0.105 - 0.180
(4.191 - 4.572)
0.060
(1.524)
TYP
0.045 - 0.055
(1.143 - 1.397)
15
TYP
0.330 - 0.370
(8.382 - 9.398)
0.059
(1.499)
TYP
0.143 + 0.012
0.143 - 0.002
(3.632 + 0305)
(3.362 - 0.508)
0.050 +/- 0.012
(1.270 +/- 0.305)
0.020 - 0.039
(0.510 - 0.990)
GM1117SV2.03
0.090 - 0.110
(2.286 - 2.794)
14
0.050
(1.270)
0.013 - 0.023
(0.330 - 0.584)
GM1117S
1A LOW DROPOUT
PRECISION VOLTAGE REGULATOR
Ordering Number
GM 1117S A
APM
Gamma
Circuit Type
Micro
ST3
R
G
Output
Voltage
Package
Type
Shipping Type
A: Adj
1.8 =1.8V
2.5 =2.5V
3.3 = 3.3V
5.0 =5.0V
ST3:
TA3:
TB3:
TC3:
Blank:
Pb-free
G:Green
SOT223
TO263
TO220
TO252
R: Taping
& Reel
T: Tube
Note:
Pb-free products:
♦
RoHS compliant and compatible with the current require-ments of IPC/JEDEC J-STD-020.
♦
Suitable for use in SnPb or Pb-free soldering processes with 100% matte tin (Sn) plating.
♦
Lead-free (RoHS compliant)
♦
Halogen free(Br or Cl does not exceed 900ppm by weight in homogeneous material and total of
Br and Cl does not exceed 1500ppm by weight)
GM1117SV2.03
Green products:
915
Similar pages