Revised December 2003 MM74HC161 • MM74HC163 Synchronous Binary Counter with Asynchronous Clear • Synchronous Binary Counter with Synchronous Clear General Description The MM74HC161 and MM74HC163 synchronous presettable counters utilize advanced silicon-gate CMOS technology and internal look-ahead carry logic for use in high speed counting applications. They offer the high noise immunity and low power consumption inherent to CMOS with speeds similar to low power Schottky TTL. The HC161 and the HC163 are 4 bit binary counters. All flip-flops are clocked simultaneously on the LOW-to-HIGH transition (positive edge) of the CLOCK input waveform. These counters may be preset using the LOAD input. Presetting of all four flip-flops is synchronous to the rising edge of CLOCK. When LOAD is held LOW counting is disabled and the data on the A, B, C, and D inputs is loaded into the counter on the rising edge of CLOCK. If the load input is taken HIGH before the positive edge of CLOCK the count operation will be unaffected. All of these counters may be cleared by utilizing the CLEAR input. The clear function on the MM74HC163 counter is synchronous to the clock. That is, the counters are cleared on the positive edge of CLOCK while the clear input is held LOW. The MM74HC161 counter is cleared asynchronously. When the CLEAR is taken LOW the counter is cleared immediately regardless of the CLOCK. Two active HIGH enable inputs (ENP and ENT) and a RIPPLE CARRY (RC) output are provided to enable easy cascading of counters. Both ENABLE inputs must be HIGH to count. The ENT input also enables the RC output. When enabled, the RC outputs a positive pulse when the counter overflows. This pulse is approximately equal in duration to the HIGH level portion of the QA output. The RC output is fed to successive cascaded stages to facilitate easy implementation of N-bit counters. All inputs are protected from damage due to static discharge by diodes to VCC and ground. Features ■ Typical operating frequency: 40 MHz ■ Typical propagation delay; clock to Q: 18 ns ■ Low quiescent current: 80 µA maximum (74HC Series) ■ Low input current: 1 µA maximum ■ Wide power supply range: 2–6V Ordering Code: Order Number MM74HC161M (Note 1) MM74HC161SJ MM74HC161MTC (Note 1) Package Number Package Description M16A 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow M16D 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide MTC16 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide MM74HC161N N16E 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide MM74HC163M (Note 1) M16A 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow MM74HC163SJ M16D 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide MM74HC163N N16E 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Note 1: Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. © 2003 Fairchild Semiconductor Corporation DS005008 www.fairchildsemi.com MM74HC161 • MM74HC163 Synchronous Binary Counter with Asynchronous Clear • Synchronous Binary Counter with Synchronous Clear September 1983 MM74HC161 • MM74HC163 Connection Diagram Truth Tables MM74HC161 CLK CLR ENP ENT Load Function X L X X X Clear X H H L H Count & RC disabled X H L H H Count disabled X H L L H Count & RC disabled ↑ H X X L Load ↑ H H H H Increment Counter MM74HC163 CLK CLR ENP ENT www.fairchildsemi.com 2 Function L X X X Clear X H H L H Count & RC disabled X H L H H Count disabled X H L L H Count & RC disabled ↑ H X X L Load ↑ H H H H Increment Counter H = HIGH Level L = LOW Level X = Don’t Care ↑ = LOW-to-HIGH Transition Logic Diagram Load ↑ Recommended Operating Conditions (Note 3) −0.5 to +7.0V Supply Voltage (VCC) DC Input Voltage (VIN) −1.5 to VCC+1.5V DC Output Voltage (VOUT) −0.5 to VCC+0.5V ±20 mA Clamp Diode Current (IIK, IOK) DC Output Current, per pin V DC Input or Output Voltage 0 VCC V −40 +85 °C (tr, tf) VCC = 2.0V 1000 ns VCC = 4.5V 500 ns VCC = 6.0V 400 ns Input Rise or Fall Times −65°C to +150°C Storage Temperature Range (TSTG) Units 6 Operating Temperature Range (TA) ±50 mA (ICC) Max 2 (VIN, VOUT ) ±25 mA (IOUT) DC VCC or GND Current, per pin Min Supply Voltage (VCC) Power Dissipation (PD) (Note 4) 600 mW S.O. Package only 500 mW Note 2: Absolute Maximum Ratings are those values beyond which damage to the device may occur. Lead Temperature DC Electrical Characteristics Symbol VIH VIL VOH Parameter Note 3: Unless otherwise specified all voltages are referenced to ground. 260°C (TL) (Soldering 10 seconds) Conditions Note 4: Power Dissipation temperature derating — plastic “N” package: − 12 mW/°C from 65°C to 85°C. (Note 5) TA = 25°C VCC Typ TA = −40 to 85°C TA = −55 to 125°C Guaranteed Limits Minimum HIGH Level 2.0V 1.5 1.5 1.5 Input Voltage 4.5V 3.15 3.15 3.15 6.0V 4.2 4.2 4.2 Maximum LOW Level 2.0V 0.5 0.5 0.5 Input Voltage 4.5V 1.35 1.35 1.35 6.0V 1.8 1.8 1.8 Minimum HIGH Level VIN = VIH or VIL Output Voltage |IOUT| ≤ 20 µA 2.0V 2.0 1.9 1.9 1.9 4.5V 4.5 4.4 4.4 4.4 6.0V 6.0 5.9 5.9 5.9 |IOUT| ≤ 4.0 mA 4.5V 4.2 3.98 3.84 3.7 |IOUT| ≤ 5.2 mA 6.0V 5.7 5.48 5.34 5.2 Units V V V VIN = VIH or VIL VOL Maximum LOW Level VIN = VIH or VIL Output Voltage |IOUT| ≤ 20 µA 2.0V 0 0.1 0.1 0.1 4.5V 0 0.1 0.1 0.1 6.0V 0 0.1 0.1 0.1 0.4 V V VIN = V IH or VIL IIN |IOUT| ≤ 4.0 mA 4.5V 0.2 0.26 0.33 |IOUT| ≤ 5.2 mA 6.0V 0.2 0.26 0.33 0.4 VIN = VCC or GND 6.0V ±0.1 ±1.0 ±1.0 µA Maximum Quiescent VIN = VCC or GND 6.0V 8.0 80 160 µA Supply Current IOUT = 0 µA Maximum Input Current ICC Note 5: For a power supply of 5V ± 10% the worst case output voltages (VOH, and VOL) occur for HC at 4.5V. Thus the 4.5V values should be used when designing with this supply. Worst case VIH and VIL occur at VCC = 5.5V and 4.5V respectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage current (IIN, ICC, and IOZ) occur for CMOS at the higher voltage and so the 6.0V values should be used. 3 www.fairchildsemi.com MM74HC161 • MM74HC163 Absolute Maximum Ratings(Note 2) MM74HC161 • MM74HC163 AC Electrical Characteristics VCC = 5V, TA = 25°C, CL = 15 pF, tr = tf = 6 ns Symbol Parameter Typ Guaranteed Limit Units fMAX Maximum Operating Frequency Conditions 43 30 MHz tPHL, tPLH Maximum Propagation Delay, Clock to RC 30 35 ns tPHL, tPLH Maximum Propagation Delay, Clock to Q 29 34 ns tPHL, tPLH Maximum Propagation Delay, ENT to RC 18 32 ns tPHL Maximum Propagation Delay, Clear to Q or RC 27 38 ns tREM Minimum Removal Time, Clear to Clock 10 tS Minimum Set Up Time Clear, Load, 20 ns 30 ns Enable or Data to Clock tH Minimum Hold Time, Data from Clock 5 ns tW Minimum Pulse Width Clock, 16 ns Clear, or Load AC Electrical Characteristics CL = 50 pF, tr = tf = 6 ns (unless otherwise specified) Symbol fMAX tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPHL tREM tS tS Parameter Conditions TA = 25°C VCC Typ TA = −40 to 85°C TA = −55 to 125°C Guaranteed Limits Maximum Operating 2.0V 10 5 4 4 Frequency 4.5V 40 27 21 18 6.0V 45 32 25 21 Maximum Propagation 2.0V 100 215 271 320 Delay, Clock to RC 4.5V 32 43 54 64 6.0V 28 37 46 54 Maximum Propagation 2.0V 88 175 220 260 Delay, Clock to RC 4.5V 18 35 44 52 6.0V 15 30 37 44 Maximum Propagation 2.0V 95 205 258 305 Delay, Clock to Q 4.5V 30 41 52 61 6.0V 26 35 44 52 Maximum Propagation 2.0V 85 170 214 253 Delay, Clock to Q 4.5V 17 34 43 51 6.0V 14 29 36 43 Maximum Propagation 2.0V 90 195 246 291 Delay, ENT to RC 4.5V 28 39 49 58 6.0V 24 33 42 49 Maximum Propagation 2.0V 80 160 202 238 Delay, ENT to RC 4.5V 16 32 40 48 6.0V 14 27 34 41 Maximum Propagation 2.0V 100 220 275 325 Delay, Clear to RC 4.5V 32 44 55 66 6.0V 28 37 47 55 Maximum Propagation 2.0V 100 210 260 315 Delay, Clear to Q 4.5V 32 42 52 63 6.0V 28 36 45 54 Minimum Removal 2.0V 125 158 186 Time Clear to Clock 4.5V 25 32 37 6.0V 21 27 32 Minimum Setup 2.0V 150 190 225 Time Clear or Data 4.5V 30 38 45 to Clock 6.0V 26 32 38 Minimum Setup 2.0V 135 170 200 Time Load 4.5V 27 34 41 to Clock 6.0V 23 29 35 www.fairchildsemi.com 4 Units MHz ns ns ns ns ns ns ns ns ns ns ns Symbol tS tH tH tW tTLH, tTHL tr, tf Parameter (Continued) Conditions TA = 25°C VCC Typ 2.0V 175 220 260 Time Enable 4.5V 35 44 52 to Clock 6.0V 30 37 44 Minimum Hold Time 2.0V 50 63 75 Data from Clock 4.5V 10 13 15 6.0V 9 11 13 Minimum Hold Time 2.0V 0 0 0 Enable, Load or Clear 4.5V 0 0 0 to Clock 6.0V 0 0 0 Minimum Pulse Width 2.0V 80 100 120 Clock, Clear, or 4.5V 16 20 24 Load 6.0V 14 17 20 Maximum 2.0V 40 75 95 110 Output Rise and 4.5V 8 15 19 22 Fall Time 6.0V 7 13 16 19 1000 1000 1000 500 500 500 400 400 400 Maximum Input Rise 2.0V and Fall Time 4.5V 500 Powert Dissipation (per package) Units Guaranteed Limits Minimum Setup 6.0V CPD TA = −40 to 85°C TA = −55 to 125°C 90 ns ns ns ns ns ns pF Capacitance (Note 6) CIN Maximum Input Capacitance 5 10 10 10 pF Note 6: CPD determines the no load dynamic power consumption, PD = CPD VCC2 f + ICC VCC, and the no load dynamic current consumption, IS = CPD VCC f + ICC. Logic Waveforms Synchronous Binary Counters Typical Clear, Preset, Count and Inhibit Sequences Sequence: (1) Clear outputs to zero (2) Preset to binary twelve (3) Count to thirteen, fourteen, fifteen, zero, one and two (4) Inhibit 5 www.fairchildsemi.com MM74HC161 • MM74HC163 AC Electrical Characteristics MM74HC161 • MM74HC163 Physical Dimensions inches (millimeters) unless otherwise noted 16-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Package Number M16A www.fairchildsemi.com 6 MM74HC161 • MM74HC163 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package Number M16D 7 www.fairchildsemi.com MM74HC161 • MM74HC163 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Package Number MTC16 www.fairchildsemi.com 8 16-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Package Number N16E Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 9 www.fairchildsemi.com MM74HC161 • MM74HC163 Synchronous Binary Counter with Asynchronous Clear • Synchronous Binary Counter with Synchronous Clear Physical Dimensions inches (millimeters) unless otherwise noted (Continued)