LD10 SERIES 10W， AC-DC CONVERTER LD10 series ----is a compact size power converter offered by Mornsun. It features universal input voltage, taking both DC and AC input voltage, low power consumption, high efficiency, high reliability, safer isolation. It offers good EMC performance, meets IEC/EN61000-4, CISPR22/EN55022 ， UL60950 and EN60601 standards, and widely used in industrial, medical, electricity, instruments, telecommunication and civil applications. For harsh EMC environment, this series of products must use the refered application circuit. E235235 RoHS PRODUCT FEATURES PART NUMBER SYSTEM 1. Universal input :85 ~ 264VAC/120～370VDC LD10-20B24A2 2. AC and DC dual-use(input from the same terminal) 3. High efficiency, high power density 4.Output over voltage, short circuit and over temperature protection 5. Low ripple and noise 6. Low loss, green power 7. Meet UL60950 and EN60601 standards 8. Industrial, medical level specifications 9.Mounting: PCB mounting, Chassis mounting with Screw Terminals, DIN-Rail mounting SELECTION GUIDE Approval Model Package LD10-20B03 UL/CE Power 6.6W Output (Vo1/Io1) Ripple and Noise (typ) Efficiency (%)(typ) Standby Power (typ) 0.4W 3.3V/2000mA 70 LD10-20B05 5V/2000mA 74 0.4W LD10-20B09 9V/1100mA 76 0.45W 53.8X28.8X19.0mm 10W 50mV 76 0.4W LD10-20B15 15V/700mA 78 0.5W LD10-20B24 24V/450mA 80 0.6W LD10-20B12 12V/900mA INPUT SPECIFICATIONS Input Voltage Range 85～264VAC, Input Frequency 47～440Hz 120～370VDC Input Current 110VAC 230mA, typ 230VAC 150mA, typ Inrush Current 110VAC 10A, typ 230VAC 20A, typ Leakage Current 0.1mA (typ)@ Vin=230Vac Recommended External Input Fuse (Special package series include fuse) 2A/250V Slow-Blow OUTPUT SPECIFICATIONS Voltage set accuracy ±2% Input variation ±0.5% (typ) ±1% (typ) Load variation (10% to 100%) Ripple& noise(p-p) 20MHz Bandwidth Short circuit protection 50mV(typ) 100mV (max) Continuous, and auto resume ≥110% I O Over current protection Maximum capacitive load (µF) (3.3V: ±3%) LD10-20B03 8000 LD10-20B05 8000 LD10-20B09 560 LD10-20B12 1200 LD10-20B15 1000 LD10-20B24 200 The copyright and authority for the interpretation of the products are reserved by MORNSUN Specifications subject to change without notice. LD10-20BXX A/3-2012 Page1 of 4 COMMON SPECIFICATIONS Operating Temperature ranges Hold-up time -25℃～+70℃ 2% / ℃ (55°C～70℃) (-25℃～0°C) Power derating 2% / ℃ Storage -40℃～+105℃ Case temperature +95℃ max 50ms(typ) (Vin=230VAC) Humidity 95%(max) Temperature coefficient 0.02%/℃ Switching frequency 60kHz(typ) Isolation voltage( Input-Output ) 4000VAC/1Min CE CISPR22/EN55022 CLASS A(without external circuit) / CLASS B(with typical applications Figure 3) RE CISPR22/EN55022 CLASS A(without external circuit) / CLASS B(with typical applications Figure 3) ESD IEC/EN 61000-4-2 Contact ±6KV /Air ±8KV perf. Criteria B RS IEC/EN 61000-4-3 10V/m perf. Criteria A IEC/EN 61000-4-4 ±2 KV (without external circuit) perf. Criteria B IEC/EN 61000-4-4 ±4 KV (with typical applications Figure 3) perf. Criteria B IEC/EN 61000-4-5 ±1KV (without external circuit) perf. Criteria B IEC/EN 61000-4-5 ±2KV/±4KV (with typical applications Figure 3) perf. Criteria B CS IEC/EN61000-4-6 10 Vr.m.s perf. Criteria A PFM IEC/EN61000-4-8 10A/m perf. Criteria A Voltage dips、short and interruptions immunity IEC/EN61000-4-11 0%-70% perf. Criteria B EMI EFT EMC EMS Surge Safety standards IEC60601,EN60601,UL60950 Safety approvals EN60601,UL60950 Safety Class CLASSⅡ Case material UL94V-0 Install PCB mounting, Chassis mounting with Screw Terminals, DIN-Rail mounting >300,000H @25℃ MTBF PCB mounting Chassis mounting with Screw Terminals DIN-Rail mounting Package 53.8X28.8X19.0mm 96.1X54.0X27.5mm 96.1X54.0X32.1mm 50g(PCB mounting) 100g(Chassis mounting with Screw Terminals) 140g(DIN-Rail mounting) Weight Note: 1. 2. Ripple and Noise were measured by the method of anear measure (more details refer to the anear measure). Unless otherwise specified, all specifications above are measured at rated input voltage and rated output load, TA=25°C, humidity < 75%. ANEAR MEASURE Conn ect Os cillog rap h Prob e Copp er sh eet FUSE Loa d C1: 1µF (Ceramic capacitor) TEMPERATURE VS LOAD C2:10µF (Electrolytic capacitor) INPUT VOLTAGE VS LOAD Load(%) Load(%) 100 100 100 80 80 80 60 50 40 60 50 40 60 50 40 20 20 -25 -10 0 55 70 Temp erat ure( C) Load(%) 70 85 100 240 264 Input voltage (Vac) The copyright and authority for the interpretation of the products are reserved by MORNSUN 80 120 340 370 Input voltage (Vdc) Specifications subject to change without notice. LD10-20BXX A/3-2012 Page2 of 4 TYPICAL APPLICATIONS FU S E NTC L L C1 +Vo C2 TVS + L L N N +Vo +Vo AC-DC RL M OV -Vo -Vo -Vo N N Figure 1:LD10 application circuit Figure 2: Note: This application is not supported for this series. can use MORNSUN’s FC-L01D FUSE R2 L L CY1 CY3 MOV LCM CX R3 CY2 ACDC CY4 OUTPUT R1 N N Figure 3:LD10 series Recommended circuit for application require higher EMC standard (external circuit output same as above) Figure 4: EMC application circuit PCB layout Safety and recommend wiring: linewidth A≥3mm,C≥9mm EXTERNAL CAPACITORS TYPICAL VALUE Model C1 C2 TVS LD10-20B03 1µF /50V 220µF /10V SMBJ7.0A LD10-20B05 1µF /50V 220µF /10V SMBJ7.0A LD10-20B09 1µF /50V 120µF /25V SMBJ12A LD10-20B12 1µF /50V 120µF /25V SMBJ20A LD10-20B15 1µF /50V 120µF /25V SMBJ20A LD10-20B24 1µF /50V 68µF /35V SMBJ30A Note: 1. Output filtering capacitors C1 is ceramic capacitor, it is used to filter high frequency noise. C2 is electrolytic capacitors, It is recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitor please refer to manufacture’s datasheet. Voltage derating of capacitor should be 80% or above. TVS is a recommended component to protect post-circuits (if converter fails). External input NTC model is recommended to use 5D-9. 2. For standard EMC requirement, please refer to figure 1, if higher EMC requirement, please refer to figure 3 or figure 4. MOV: Varistor, model: 561KD14，it is used to protect the device under surge; R1 、R2：2Ω/3W Winding resistor； R3：1MΩ/2W； CY1、CY2、CY3、CY4：102M/400VAC； CX：0.22µF /275VAC； LCM：10mH-30mH； FC-L01D：MORNSUN’s 2KV/4KV Surge protector. 3.FUSE：LD10 is recommended to use 2A/250V. 19.00 [ 0. 7 4 8] 6.00 [ 0 . 23 6 ] PCB MOUNTING WITH SOLDER PINS (Main View) Ф1.00 [0.03 9] RECOMMENDED FOOTPRINT 3 1 2 2 (Bottom View) 1 4 3 10.16 [ 0. 4 0 0] 28.80[1.13 4] 10.16 10.16 [0. 4 0 0] [ 0 . 40 0 ] 4 Ф1.50[0.059] Note: grid2.54*2.54mm. 45.72[1.800] 53.80[2.118] FOOTPRINT DETAILS Note: Unit: mm[inch] Pin diameter tolerances: ± 0 .10mm[± 0.004inch] General tolerances: ± 0.50mm[± 0.020inch] The copyright and authority for the interpretation of the products are reserved by MORNSUN PIN 1 2 3 4 FUNCTION N L +Vo - Vo Specifications subject to change without notice. LD10-20BXX A/3-2012 Page3 of 4 LD10XXA2 CHASSIS MOUNTING WITH SCREW TERMINALS 96.10 [3.783] 86.10 [3.390] 4 1 2 3 5 6 7 8 ( Top View ) 46.00[1.811] 54.00[2.126] Ф 3.50 [0.138] ( Main View ) Footprint Details 1 Pin NC Function 2 3 4 5 6 7 8 AC(N) AC(L) +Vo NC -Vo NC NC 8.50 [0.335] 20.60 [0.811] 27.50 [1.083] Note: Unit: mm[inch] General tolerances: ±0.50mm[±0.020inch] LD10XXA4 DIN-RAIL MOUNTING 5 6 7 8 ( Top View ) ( Main View ) Footprint Details 1 Pin NC Function 32.10[1.264] 4 1 2 3 46.00[1.811] 54.00[2.126] 96.10[3.783] 86.10[3.390] 8.50[0.335] 20.60[0.811] 27.50[1.083] 2 3 4 5 6 7 8 AC(N) AC(L) +Vo NC -Vo NC NC Note: Unit: mm[inch] General tolerances: ±0.50mm[±0.020inch] PACKAGE DIAGRAM Special Package Series PCB mounting Series Inner packaging box dimensions: L*W*H=255*170*80mm Packaging quantity: 24pcs Outer packaging box dimensions: L*W*H=405*380*305mm Packaging quantity: 144pcs Inner packaging box dimensions: L*W*H=365*350*105mm Packaging quantity: 24pcs Outer packaging box dim ensions: L*W*H=390*360*245mm Packaging quantity: 48pcs MORNSUN Science & Technology Co.,Ltd. Address: No. 5, Kehui St. 1, Kehui development center, Science Ave., Guangzhou Science City, Luogang district, Guangzhou,P.R.China. Tel: 86-20-28203030 Fax:86-20-38601272 Http://www.mornsun-power.com The copyright and authority for the interpretation of the products are reserved by MORNSUN Specifications subject to change without notice. LD10-20BXX A/3-2012 Page4 of 4