IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM Integrated Device Technology, Inc. • Interrupt and Busy Flags • On-chip port arbitration logic • Full on-chip hardware support of semaphore signaling between ports • Fully asynchronous operation from either port • Devices are capable of withstanding greater than 2001V electrostatic discharge • TTL-compatible, single 5V (±10%) power supply • Available in ceramic 68-pin PGA, 68-pin PLCC, and an 80-pin TQFP • Industrial temperature range (–40°C to +85°C) is available, tested to military electrical specifications FEATURES: • True Dual-Ported memory cells which allow simultaneous access of the same memory location • High-speed access — Military: 20/25/35ns (max.) — Commercial: 12/15/17/20/25/35ns (max.) • Low-power operation — IDT7015S Active: 750mW (typ.) Standby: 5mW (typ.) — IDT7015L Active: 750mW (typ.) Standby: 1mW (typ.) • IDT7015 easily expands data bus width to 18 bits or more using the Master/Slave select when cascading more than one device • M/S = H for BUSY output flag on Master M/S = L for BUSY input on Slave DESCRIPTION: The IDT7015 is a high-speed 8K x 9 Dual-Port Static RAMs. The IDT7015 is designed to be used as stand-alone Dual-Port RAM or as a combination MASTER/SLAVE DualPort RAM for 18-bit-or-more word systems. Using the IDT FUNCTIONAL BLOCK DIAGRAM OER OEL CER CEL WR WL R/ R/ I/O0L- I/O8L I/O0R-I/O8R I/O Control I/O Control BUSYL (1,2) A12L A0L BUSYR Address Decoder MEMORY ARRAY 13 CEL OEL WL Address Decoder (1,2) A12R A0R 13 ARBITRATION INTERRUPT SEMAPHORE LOGIC R/ SEML CER OER WR R/ SEMR M/S (2) (2) INTL INTR 2954 drw 01 NOTES: 1. In MASTER mode: BUSY is an output and is a push-pull driver In SLAVE mode: BUSY is input. 2. BUSY outputs and INT outputs are non-tri-stated push-pull drivers. The IDT logo is a registered trademark of Integrated Device Technology, Inc. MILITARY AND COMMERCIAL TEMPERATURE RANGES ©1996 Integrated Device Technology, Inc. OCTOBER 1996 For latest information contact IDT’s web site at www.idt.com or fax-on-demand at 408-492-8391. 6.12 DSC-2954/2 1 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES MASTER/SLAVE Dual-Port RAM approach in 18-bit or wider memory system applications results in full-speed, error-free operation without the need for additional discrete logic. This device provides two independent ports with separate control, address, and I/O pins that permit independent, asynchronous access for reads or writes to any location in memory. An automatic power down feature controlled by CE permits the on-chip circuitry of each port to enter a very low standby power mode. Fabricated using IDT’s CMOS high-performance technology, these devices typically operate on only 750mW of power. The IDT7015 is packaged in a ceramic 68-pin PGA, a 64pin PLCC and an 80-pin TQFP (Thin Quad FlatPack). Military grade product is manufactured in compliance with the latest revision of MIL-STD-883, Class B, making it ideally suited to military temperature applications demanding the highest level of performance and reliability. CEL N/C N/C VCC A12L A11L A10L A9L A8L A7L A6L WL SEML 10 1 68 67 66 65 64 63 62 61 60 11 59 12 58 13 57 9 8 7 6 5 4 3 14 2 16 J68-1 PLCC 17 18 19 55 A5L A4L A3L A2L A1L A0L 54 INTL 56 IDT7015 (8K x 9) 15 53 52 (3) 51 BUSYL GND M/S 50 BUSYR 21 49 INTR 22 48 23 47 24 46 25 45 A0R A1R A2R A3R A4R TOP VIEW 20 N/C N/C GND A12R A11R A10R A9R A8R A7R A6R A5R CER OER R/ WR SEMR 44 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 I/O7R I/O8R I/O2L I/O3L I/O4L I/O5L GND I/O6L I/O7L VCC GND I/O0R I/O1R I/O2R VCC I/O3R I/O4R I/O5R I/O6R OEL INDEX R/ I/O1L I/O0L I/O8L PIN CONFIGURATIONS (1,2) 2954 drw 02 NOTES: 1. All VCC pins must be connected to power supply. 2. All GND pins must be connected to ground supply. 3. This text does not imply orientation of Part-Mark. PIN NAMES Left Port Right Port CEL Names R/WL OEL CER R/WR OER A0L – A12L A0R – A12R Address I/O0L – I/O8L I/O0R – I/O8R Data Input/Output SEML INTL BUSYL SEMR INTR BUSYR M/S Chip Enable Read/Write Enable Output Enable Semaphore Enable Interrupt Flag Busy Flag Master or Slave Select VCC Power GND Ground 2954 tbl 01 6.12 2 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES NC NC A7L A6L A9L A8L VCC A12L A11L A10L NC NC 74 73 W NC SEML 75 CEL R/ L 79 78 77 76 OEL I/O1L I/O0L I/O8L 80 PIN CONFIGURATIONS (CON'T.) (1,2) 62 61 66 65 64 63 68 67 70 69 72 71 INDEX 60 59 NC I/O2L 1 2 I/O3L 58 I/O4L 3 4 I/O5L 5 56 GND 6 7 55 I/O6L I/O7L 9 10 GND 11 12 I/O1R I/O2R 54 53 IDT7015 (8K X 9) 8 VCC NC I/O0R 57 PN-80 TQFP 13 INTR 46 A1R A2R 16 45 I/O4R 44 I/O5R 17 18 I/O6R 19 42 NC 20 41 40 A0R A3R A4R NC NC 2954 drw 03 NC 39 37 38 A5R NC A6R 35 36 A7R 33 34 A10R A9R A8R 32 A11R A12R 30 31 29 NC GND 27 28 NC NC CER 26 24 25 W SEMR OER R/ R 22 23 43 21 BUSYR 48 47 I/O3R I/O7R I/O8R INTL GND M/S VCC 51 A5L 50 A4L 48 A2L 46 44 42 A0L BUSYL M/S 49 A3L 47 A1L 45 40 38 A1R 36 A3R 43 41 39 37 GND BUSYR A0R A2R 35 A4R 34 A5R INTR 53 A7L 52 10 55 A9L 54 09 A8L 32 A7R 33 A6R 08 57 56 A11L A10L 30 A9R 31 A8R 07 59 58 VCC A12L 06 61 60 N/C N/C 05 A6L 63 62 65 64 INTL 28 29 A11R A10R IDT7015 (8K x 9) G68-1 68-PIN PGA TOP VIEW 26 27 GND A12R (3) SEML CEL 04 OEL R/WL 03 67 66 I/O0L I/O8L 02 1 3 68 I/O1L I/O2L I/O4L 01 2 4 I/O3L I/O5L A NOTES: 1. All Vcc must be connected to power supply. 2. All GND must be connected to ground supply. 3. This text does not imply orientation of Part-Mark. A1L A0L BUSYL 14 15 11 A3L A2L 51 49 (3) A5L A4L 52 50 TOP VIEW NC B 24 N/C 25 N/C 22 23 20 21 R/ R SEMR OER C CER W 5 7 9 11 13 15 GND I/O7L GND I/O1R VCC I/O4R 18 19 I/O7R I/O8R 6 8 I/O6L VCC 17 I/O6R D E 10 12 14 16 I/O0R I/O2R I/O3R I/O5R F G H J K L INDEX 2954 drw 04 6.12 3 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES TRUTH TABLE: NON-CONTENTION READ/WRITE CONTROL Inputs(1) Outputs CE R/W OE SEM H X X H High-Z Deselected: Power-Down L L X H DATAIN Write to Memory L H L H DATAOUT X X H X High-Z Mode I/O0-8 Read Memory Outputs Disabled NOTE: 1. Condition: A0L — A12L is not equal to A0R — A12R. 2954 tbl 02 TRUTH TABLE: SEMAPHORE READ/WRITE CONTROL Inputs (1) Outputs CE R/W OE SEM I/O0-8 H H L DATAOUT H u L X L DATAIN L X X L — Mode Read Semaphore Flag Data Out (I/O0-8) Write I/O0 into Semaphore Flag Not Allowed NOTE: 1. There are eight semaphore flags written to via I/O0 and read from I/O0-8 . These eight semaphores are addressed by A0 - A2. ABSOLUTE MAXIMUM RATINGS(1) Symbol Military Unit Terminal Voltage –0.5 to +7.0 with Respect to GND –0.5 to +7.0 V TA Operating Temperature 0 to +70 –55 to +125 °C TBIAS Temperature Under Bias –55 to +125 –65 to +135 °C TSTG Storage Temperature –55 to +125 –65 to +150 °C IOUT DC Output Current 50 50 mA VTERM (2) Rating Commercial 2954 tbl 03 RECOMMENDED OPERATING TEMPERATURE AND SUPPLY VOLTAGE Grade Military Commercial Ambient Temperature GND VCC –55°C to +125°C 0V 5.0V ± 10% 0°C to +70°C 0V 5.0V ± 10% 2954 tbl 05 RECOMMENDED DC OPERATING CONDITIONS Symbol NOTES: 2954 tbl 04 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VTERM must not exceed Vcc + 0.5V for more than 25% of the cycle time or 10ns maximum, and is limited to < 20mA for the period of VTERM > Vcc + 0.5V. Parameter Min. Typ. Max. Unit VCC Supply Voltage 4.5 5.0 5.5 V GND Supply Voltage 0 0 0 V VIH Input High Voltage 2.2 — 6.0(2) V — 0.8 V VIL Input Low Voltage –0.5 (1) NOTES: 1. VIL > -1.5V for pulse width less than 10ns. 2. VTERM must not exceed Vcc + 0.5V. 2954 tbl 06 CAPACITANCE(1) (TA = +25°C, f = 1.0MHz) TQFP ONLY Symbol Parameter Conditions(2) Max. Unit CIN Input Capacitance VIN = 3dV 9 pF COUT Output Capacitance VOUT = 3dV 10 pF 2954 tbl 07 NOTES: 1. This parameter is determined by device characteristics but is not production tested. 2. 3dV references the interpolated capacitance when the input and output signals switch from 0V to 3V or from 3V to 0V . 6.12 4 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES DC ELECTRICAL CHARACTERISTICS OVER THE OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE (VCC = 5.0V ± 10%) 7015S Symbol Parameter 7015L Test Conditions Min. Max. Min. Max. Unit |ILI| Input Leakage Current (1) VCC = 5.5V, VIN = 0V to VCC — 10 — 5 µA |ILO| Output Leakage Current CE = VIH, VOUT = 0V to VCC — 10 — 5 µA VOL Output Low Voltage IOL = 4mA — 0.4 — 0.4 V VOH Output High Voltage IOH = -4mA 2.4 — 2.4 — V NOTE: 1. At Vcc < 2.0V, Input leakages are undefined. 2954 tbl 08 DC ELECTRICAL CHARACTERISTICS OVER THE OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(1) (VCC = 5.0V ± 10%) Symbol ICC ISB1 ISB2 Parameter Version 7015X15 Com'l. Only Typ.(2) Max. 7015X17 Com'l. Only Typ.(2) Max. Unit CE = VIL, Outputs Open SEM = VIH MIL. S L — — — — — — — — — — — — (Both Ports Active) f = fMAX(3) COM’L. S L 170 170 325 275 170 170 310 260 170 170 310 260 Standby Current (Both Ports — TTL CER = CEL = VIH SEMR = SEML = VIH MIL. S L — — — — — — — — — — — — Level Inputs) f = fMAX(3) COM’L. S L 25 25 70 60 25 25 60 50 25 25 60 50 Standby Current (One Port — TTL CE"A"=VIL and CE"B" = VIH(5) MIL. Active Port Outputs Open S L — — — — — — — — — — — — COM’L. S L 105 105 200 170 105 105 190 160 105 109 190 160 MIL. S L — — — — — — — — — — — — COM’L. S L 1.0 0.2 15 5 1.0 0.2 15 5 1.0 0.2 15 5 MIL. S L — — — — — — — — — — — — mA COM’L. S L 100 100 180 150 100 100 170 140 100 100 170 140 mA Full Standby Current (Both Ports — All CMOS Level Inputs) ISB4 7015X12 Com'l. Only Typ.(2) Max. Dynamic Operating Current Level Inputs) ISB3 Test Condition Full Standby Current (One Port — All CMOS Level Inputs) f = fMAX(3) SEMR = SEML = VIH Both Ports CEL and CER > VCC - 0.2V VIN > VCC - 0.2V or VIN < 0.2V, f = 0(4) SEMR = SEML > VCC - 0.2V CE"A"< 0.2V and CE"B" > VCC - 0.2V(5) SEMR = SEML > VCC - 0.2V VIN > VCC - 0.2V or VIN < 0.2V Active Port Outputs Open, f = fMAX(3) mA mA mA mA NOTES: 2954 tbl 09 1. "X" in part numbers indicates power rating (S or L). 2. VCC = 5V, TA = +25°C, and are not production tested. ICCDC = 120mA(typ.) 3. At f = fMAX, address and I/O'S are cycling at the maximum frequency read cycle of 1/tRC, and using “AC Test Conditions” of input levels of GND to 3V. 4. f = 0 means no address or control lines change. 5. Port "A" may be either left or right port. Port "B" is the opposite of port "A". 6.12 5 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES DC ELECTRICAL CHARACTERISTICS OVER THE OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(1)(Cont'd) (VCC = 5.0V ± 10%) 7015X20 Symbol ICC ISB1 ISB2 ISB3 ISB4 Test Condition Parameter Version 7015X25 Typ.(2) Max. 7015X35 Typ.(2) Max. Typ.(2) Max. Unit Dynamic Operating Current CE = VIL, Outputs Open SEM = VIH MIL. S L — — — — 155 155 340 280 150 150 300 250 (Both Ports Active) f = fMAX(3) COM’L. S L 160 160 290 240 155 155 265 220 150 150 250 210 Standby Current (Both Ports — TTL CEL = CER = VIH SEMR = SEML = VIH MIL. S L — — — — 16 16 80 65 13 13 80 65 Level Inputs) f = fMAX(3) COM’L. 20 20 60 50 16 16 60 50 13 13 60 50 Standby Current CE"A"=VIL and CE"B"=VIH(5) S L MIL. S — — 90 215 85 190 L — — 90 180 85 160 COM’L. S 95 180 90 170 85 155 L 95 150 90 140 85 130 S L S L — — 1.0 0.2 — — 15 5 1.0 0.2 1.0 0.2 30 10 15 5 1.0 0.2 1.0 0.2 30 10 15 5 mA MIL. S L — — — — 85 85 200 170 80 80 175 150 mA COM’L. S L 90 90 155 130 85 85 145 120 80 80 135 110 (One Port — TTL Active Port Outputs Open Level Inputs) f = fMAX(3) SEMR = SEML = VIH Both Ports CEL and CER > VCC - 0.2V VIN > VCC - 0.2V or VIN < 0.2V, f = 0(4) SEMR = SEML > VCC - 0.2V CE"A"< 0.2V and CE"B" > VCC - 0.2V(5) SEMR = SEML > VCC - 0.2V VIN > VCC - 0.2V or VIN < 0.2V Active Port Outputs Open, f = fMAX(3) Full Standby Current (Both Ports — All CMOS Level Inputs) Full Standby Current (One Port — All CMOS Level Inputs) MIL. COM’L. NOTES: 1. "X" in part numbers indicates power rating (S or L). 2. VCC = 5V, TA = +25°C, and are not production tested. ICCDC = 120mA(typ.) 3. At f = fMAX, address and I/O'S are cycling at the maximum frequency read cycle of 1/ tRC, and using “AC Test Conditions” of input levels of GND to 3V. 4. f = 0 means no address or control lines change. 5. Port "A" may be either left or right port. Port "B" is the opposite of port "A". OUTPUT LOADS AND AC TEST CONDITIONS Input Pulse Levels GND to 3.0V Input Rise/Fall Times(1) 5ns Max. Input Timing Reference Levels 1.5V Output Reference Levels 1.5V Output Load Figure 1 and 2 mA mA mA 2954 tbl 10 5V 5V 893Ω 893Ω DATAOUT BUSY INT DATAOUT 347Ω 30pF 347Ω 5pF * NOTE: 1. 3ns Max. for tAA=12ns 2954 drw 05 Figure 1. AC Output Test Load 6.12 2954 drw 06 Figure 2. Output Test Load (For tLZ, tHZ, tWZ, tOW) Including scope and jig. 6 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES AC ELECTRICAL CHARACTERISTICS OVER THE OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(4) Symbol IDT7015X12 Com'l. Only Min. Max. Parameter IDT7015X15 Com'l. Only Min. Max. IDT7015X17 Com'l. Only Min. Max. Unit READ CYCLE tRC Read Cycle Time 12 tAA Address Access Time — 12 — 15 — 17 ns tACE Chip Enable Access Time(3) — 12 — 15 — 17 ns tAOE Output Enable Access Time — 8 — 10 — 10 ns tOH Output Hold from Address Change 3 — 3 — 3 — ns (1, 2) tLZ Output Low-Z Time tHZ Output High-Z Time(1, 2) tPU Chip Enable to Power Up Time(2) (2) tPD Chip Disable to Power Down Time tSOP Semaphore Flag Update Pulse (OE or SEM) tSAA Semaphore Address Access Time Symbol Parameter — 15 — 17 — ns 3 — 3 — 3 — ns — 10 — 10 — 10 ns 0 — 0 — 0 — ns — 12 — 15 — 17 ns 10 — 10 — 10 — ns — 12 — 15 — 17 ns IDT7015X20 IDT7015X25 IDT7015X35 Min. Max. Min. Max. Min. Max. Unit READ CYCLE tRC Read Cycle Time 20 — 25 — 35 — ns tAA Address Access Time — 20 — 25 — 35 ns tACE Chip Enable Access Time(3) — 20 — 25 — 35 ns tAOE Output Enable Access Time — 12 — 13 — 20 ns tOH Output Hold from Address Change 3 — 3 — 3 — ns (1, 2) 3 — 3 — 3 — ns (1, 2) tLZ Output Low-Z Time tHZ Output High-Z Time — 12 — 15 — 20 ns tPU Chip Enable to Power Up Time(2) 0 — 0 — 0 — ns tPD Chip Disable to Power Down Time(2) — 20 — 25 — 35 ns tSOP Semaphore Flag Update Pulse (OE or SEM) 10 — 10 — 15 — ns tSAA Semaphore Address Access Time — 20 — 25 — 35 NOTES: 1. 2. 3. 4. ns 2954 tbl 11 Transition is measured ±200mV from Low- or High-impedance voltage with the Output test load (Figure 2). This parameter is guaranteed by device characterization but not tested. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. "X" in part numbers indicates power rating (S or L). 6.12 7 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES WAVEFORM OF READ CYCLES(5) tRC ADDR (4) tAA (4) tACE CE (4) tAOE OE W R/ tLZ tOH (1) DATAOUT VALID DATA (4) tHZ(2) BUSYOUT (3, 4) tBDD 2954 drw 07 NOTES: 1. Timing depends on which signal is asserted last, OE or CE. 2. Timing depends on which signal is de-asserted first, CE or OE. 3. tBDD delay is required only in cases where the opposite port is completing a write operation to the same address location. For simultaneous read operations BUSY has no relation to valid output data. 4. Start of valid data depends on which timing becomes effective last tAOE, tACE, tAA or tBDD. 5. SEM = VIH. TIMING OF POWER-UP / POWER-DOWN CE tPU tPD ICC 50% 50% ISB 2954 drw 08 6.12 8 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES AC ELECTRICAL CHARACTERISTICS OVER THE OPERATING TEMPERATURE AND SUPPLY VOLTAGE(5) Symbol Parameter IDT7015X12 Com'l. Only Min. Max. IDT7015X15 Com'l. Only Min. Max. IDT7015X17 Com'l. Only Min. Max. Unit WRITE CYCLE 12 — 15 — 17 — ns tEW (3) Chip Enable to End-of-Write 10 — 12 — 12 — ns tAW Address Valid to End-of-Write 10 — 12 — 12 — ns tAS Address Set-up Time(3) 0 — 0 — 0 — ns tWP Write Pulse Width 10 — 12 — 12 — ns tWR Write Recovery Time 2 — 2 — 2 — ns tDW Data Valid to End-of-Write 10 — 10 — 10 — ns — 10 — 10 — 10 ns tWC tHZ Write Cycle Time (1, 2) Output High-Z Time (4) tDH Data Hold Time 0 — 0 — 0 — ns tWZ Write Enable to Output in High-Z(1, 2) — 10 — 10 — 10 ns tOW Output Active from End-of-Write(1, 2, 4) 3 — 3 — 0 — ns 5 — 5 — 5 — ns 5 — 5 — 5 — ns tSWRD tSPS SEM Flag Write to Read Time SEM Flag Contention Window Symbol Parameter IDT7015X20 IDT7015X25 IDT7015X35 Min. Min. Min. Max. Max. Max. Unit WRITE CYCLE tWC Write Cycle Time 20 — 25 — 35 — ns tEW Chip Enable to End-of-Write(3) 15 — 20 — 30 — ns tAW Address Valid to End-of-Write 15 — 20 — 30 — ns (3) tAS Address Set-up Time 0 — 0 — 0 — ns tWP Write Pulse Width 15 — 20 — 25 — ns tWR Write Recovery Time 2 — 2 — 2 — ns tDW Data Valid to End-of-Write 15 — 15 — 15 — ns tHZ Output High-Z Time(1, 2) — 12 — 15 — 20 ns 0 — 0 — 0 — ns tDH (4) Data Hold Time (1, 2) tWZ Write Enable to Output in High-Z — 12 — 15 — 20 ns tOW Output Active from End-of-Write(1, 2, 4) 3 — 3 — 3 — ns 5 — 5 — 5 — ns 5 — 5 — 5 — ns tSWRD tSPS SEM Flag Write to Read Time SEM Flag Contention Window NOTES: 2954 tbl 12 1. Transition is measured ±200mV from Low or High-impedance voltage with the Output test load (Figure 2). 2. This parameter is guaranteed by device characterization but not tested. 3. To access RAM, CE = VIL and SEM = VIH. To access semaphore, CE = VIH and SEM = VIL. Either condition must be valid for the entire tEW time. 4. The specification for tDH must be met by the device supplying write data to the RAM under all operating conditions. Although tDH and tOW values will vary over voltage and temperature, the actual tDH will always be smaller than the actual tOW. 5. "X" in part numbers indicates power rating (S or L). 6.12 9 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES TIMING WAVEFORM OF WRITE CYCLE NO. 1, R/W CONTROLLED TIMING(1,5,8) tWC ADDRESS tHZ (7) OE tAW CE or SEM (9) tAS (6) tWP (2) tWR (3) W R/ tWZ DATA OUT (7) tOW (4) (4) tDW tDH DATA IN 2954 drw 09 TIMING WAVEFORM OF WRITE CYCLE NO. 2, CE CONTROLLED TIMING(1,5) tWC ADDRESS tAW CE or SEM (9) (6) tAS tWR(3) tEW (2) W R/ tDW tDH DATAIN 2954 drw 10 NOTES: 1. R/W or CE must be High during all address transitions. 2. A write occurs during the overlap (tEW or tWP) of a Low CE and a Low R/W for memory array writing cycle. 3. tWR is measured from the earlier of CE or R/W (or SEM or R/W) going High to the end of write cycle. 4. During this period, the I/O pins are in the output state and input signals must not be applied. 5. If the CE or SEM Low transition occurs simultaneously with or after the R/W Low transition, the outputs remain in the High-impedance state. 6. Timing depends on which enable signal is asserted last, CE or R/W. 7. This parameter is guaranteed by device characterization but is not production tested, transition is measured +/-200mV from steady state with the Output Test load (Figure 2). 8. If OE is Low during R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off and data to be placed on the bus for the required tDW. If OE is High during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the specified tWP. 9. To access RAM, CE = VIL and SEM = VIH. To access Semaphore, CE = VIH and SEM = VIL. tEW must be met for either condition. 6.12 10 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES TIMING WAVEFORM OF SEMAPHORE READ AFTER WRITE TIMING, EITHER SIDE(1) tOH tSAA A0-A2 VALID ADDRESS tWR tAW tEW SEM tACE tSOP tDW DATAIN VALID I/O R/ VALID ADDRESS tAS W tWP DATAOUT VALID(2) tDH tSWRD tAOE OE Write Cycle Read Cycle 2954 drw 11 NOTES: 1. CE = VIH for the duration of the above timing (both write and read cycle). 2. "DATAOUT VALID" represents all I/O's (I/O0-I/O8) equal to the semaphore value. TIMING WAVEFORM OF SEMAPHORE WRITE CONTENTION(1,3,4) A0"A"-A2 "A" SIDE(2) "A" MATCH W"A" R/ SEM"A" A0"B"-A2 "B" SIDE(2) "B" tSPS MATCH W"B" R/ SEM"B" 2954 drw 12 NOTES: 1. DOR = DOL =VIH, CER = CEL =VIH. 2. All timing is the same for left and right ports. Port “A” may be either left or right port. “B” is the opposite port from “A”. 3. This parameter is measured from R/W"A" or SEM"A" going high to R/W"B" or SEM"B" going High. 4. If tSPS is not satisfied, there is no guarantee which side will obtain the semaphore flag. 6.12 11 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES AC ELECTRICAL CHARACTERISTICS OVER THE OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(6) Symbol IDT7015X12 Com'l. Only Min. Max. Parameter IDT7015X15 Com'l. Only Min. Max IDT7015X17 Com'l. Only Min Max. Unit BUSY TIMING (M/S = VIH) tBDC BUSY Access Time from Address Match BUSY Disable Time from Address Not Matched BUSY Access Time from Chip Enable Low BUSY Disable Time from Chip Enable High tAPS Arbitration Priority Set-up Time(2) tBAA tBDA tBAC BUSY Disable to Valid Data Write Hold After BUSY(5) BUSY TIMING (M/S = VIL) BUSY Input to Write(4) tWB tWH Write Hold After BUSY(5) (3) tBDD tWH — 12 — 15 — 17 ns — 12 — 15 — 17 ns — 12 — 15 — 17 ns — 12 — 15 — 17 ns 5 — 5 — 5 — ns — 15 — 18 — 18 ns 11 — 13 — 13 — ns 0 — 0 — 0 — ns 11 — 13 — 13 — ns PORT-TO-PORT DELAY TIMING tWDD Write Pulse to Data Delay(1) — 25 — 30 — 30 ns tDDD Write Data Valid to Read Data Delay(1) — 20 — 25 — 25 ns Symbol Parameter IDT7015X20 IDT7015X25 IDT7015X35 Min. Max. Min. Max. Min. Max. Unit — 20 — 20 — 20 ns — 20 — 20 — 20 ns — 20 — 20 — 20 ns — 17 — 17 — 20 ns 5 — 5 — 5 — ns BUSY TIMING (M/S = VIH) tBAA tBDA tBAC tBDC tAPS BUSY Access Time from Address Match BUSY Disable Time from Address Not Matched BUSY Access Time from Chip Enable Low BUSY Disable Time from Chip Enable High Arbitration Priority Set-up Time BUSY Disable to Valid Data Write Hold After BUSY(5) BUSY TIMING (M/S = VIL) tWB BUSY Input to Write(4) tWH Write Hold After BUSY(5) tBDD (2) (3) tWH — 30 — 30 — 35 ns 15 — 17 — 25 — ns 0 — 0 — 0 — ns 15 — 17 — 25 — ns — 45 — 50 — 60 ns — 30 — 35 — 45 ns PORT-TO-PORT DELAY TIMING tWDD tDDD Write Pulse to Data Delay(1) Write Data Valid to Read Data Delay (1) NOTES: 1. Port-to-port delay through RAM cells from writing port to reading port, refer to "Timing Wave form of Write with Port-to-Port Read and 2. To ensure that the earlier of the two ports wins. 3. tBDD is a calculated parameter and is the greater of 0, tWDD – tWP (actual), or tDDD – tDW (actual). 4. To ensure that the write cycle is inhibited on port "B" during contention on port "A". 5. To ensure that a write cycle is completed on port "B" after contention on port "A". 6. "X" in part numbers indicates power rating (S or L). 6.12 2940 tbl 13 BUSY (M/S = VIH)". 12 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES TIMING WAVEFORM OF READ WITH BUSY (M/S = VIH)(2,4,5) tWC MATCH ADDR"A" tWP W"A" R/ tDH tDW VALID DATAIN "A" tAPS (1) MATCH ADDR"B" tBDA tBDD BUSY"B" tWDD DATAOUT "B" VALID tDDD (3) 2954 drw 13 NOTES: 1. To ensure that the earlier of the two ports wins. tAPS is ignored for M/S=VIL. 2. CEL = CER = VIL. 3. OE = VIL for the reading port. 4. If M/S = VIL (slave), BUSY is an input. Then for this example BUSY"A" = VIH and BUSY"B" input is shown above. 5. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from port "A". TIMING WAVEFORM OF WRITE WITH BUSY tWP W"A" R/ tWB BUSY"B" tWH( 1 ) W"B" R/ (2) NOTES: 2954 drw 14 1. tWH must be met for both BUSY input (SLAVE) and output (MASTER). 2. BUSY is asserted on port "B" blocking R/W"B", until BUSY"B" goes High. 3. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from port "A". 6.12 13 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES WAVEFORM OF BUSY ARBITRATION CONTROLLED BY CE TIMING (M/S = VIH)(1) ADDR"A" and "B" ADDRESSES MATCH CE"A" tAPS (2) CE"B" tBAC tBDC BUSY"B" 2954 drw 15 WAVEFORM OF BUSY ARBITRATION CYCLE CONTROLLED BY ADDRESS MATCH TIMING (M/S = VIH)(1) ADDR"A" ADDRESS "N" tAPS (2) ADDR"B" MATCHING ADDRESS "N" tBAA tBDA BUSY"B" 2954 drw 16 NOTES: 1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from “A”. 2. If tAPS is not satisfied, the busy signal will be asserted on one side or another but there is no guarantee on which side busy will be asserted. AC ELECTRICAL CHARACTERISTICS OVER THE OPERATING TEMPERATURE AND SUPPLY VOLTAGE RANGE(1) Symbol Parameter IDT7015X12 Com'l. Only Min. Max. IDT7015X15 Com'l. Only Min. Max. IDT7015X17 Com'l. Only Min Max. Unit INTERRUPT TIMING tAS Address Set-up Time 0 — 0 — 0 — ns tWR Write Recovery Time 0 — 0 — 0 — ns tINS Interrupt Set Time — 12 — 15 — 17 ns tINR Interrupt Reset Time — 12 — 15 — 17 ns Symbol Parameter IDT7015X20 IDT7015X25 IDT7015X35 Min. Max. Min. Max. Min. Max. Unit INTERRUPT TIMING tAS Address Set-up Time 0 — 0 — 0 — ns tWR Write Recovery Time 0 — 0 — 0 — ns tINS Interrupt Set Time — 20 — 20 — 25 ns tINR Interrupt Reset Time — 20 — 20 — 25 ns NOTE: 1. "X" in part numbers indicates power rating (S or L). 2739 tbl 14 6.12 14 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES WAVEFORM OF INTERRUPT TIMING(1) tWC INTERRUPT SET ADDRESS ADDR"A" tAS (2) (3) tWR (4) CE"A" W"A" R/ tINS (3) INT"B" 2954 drw 17 tRC INTERRUPT CLEAR ADDRESS ADDR"B" tAS (2) (3) CE"B" OE"B" tINR (3) INT"B" 2954 drw 18 NOTES: 1. All timing is the same for left and right ports. Port “A” may be either the left or right port. Port “B” is the port opposite from “A”. 2. See Interrupt truth table. 3. Timing depends on which enable signal (CE or R/W) is asserted last. 4. Timing depends on which enable signal (CE or R/W) is de-asserted first. TRUTH TABLES TRUTH TABLE I — INTERRUPT FLAG(1) Left Port R/WL L CEL L OEL X Right Port A12L-A0L 1FFF INTL X R/WR X CER X OER X A12R-A0R X INTR L (2) X X X X X X L L 1FFF X X X X L(3) L L X 1FFE X (2) X X X X X X L L 1FFE H NOTES: 1. Assumes BUSYL = BUSYR = VIH. 2. If BUSYL = VIL, then no change. 3. If BUSYR = VIL, then no change. H (3) Function Set Right INTR Flag Reset Right INTR Flag Set Left INTL Flag Reset Left INTL Flag 2954 tbl 15 6.12 15 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES TRUTH TABLE II — ADDRESS BUSY ARBITRATION Inputs Outputs CEL CER A0L-A12L A0R-A12R X X NO MATCH H H Normal H X MATCH H H Normal X H MATCH H H Normal L L MATCH (2) (2) Write Inhibit(3) (1) BUSYL BUSYR (1) Function NOTES: 2954 tbl 16 1. Pins BUSYL and BUSYR are both outputs when the part is configured as a master. Both are inputs when configured as a slave. BUSYX outputs on the IDT7015 are push-pull, not open drain outputs. On slaves the BUSYX input internally inhibits writes. 2. "L" if the inputs to the opposite port were stable prior to the address and enable inputs of this port. "H" if the inputs to the opposite port became stable after the address and enable inputs of this port. If t APS is not met, either BUSYL or BUSYR = Low will result. BUSYL and BUSYR outputs can not be low simultaneously. 3. Writes to the left port are internally ignored when BUSYL outputs are driving low regardless of actual logic level on the pin. Writes to the right port are internally ignored when BUSYR outputs are driving low regardless of actual logic level on the pin. TRUTH TABLE III — EXAMPLE OF SEMAPHORE PROCUREMENT SEQUENCE(1,2) Functions D0 - D8 Left D0 - D8 Right Status No Action 1 1 Semaphore free Left Port Writes "0" to Semaphore 0 1 Left port has semaphore token Right Port Writes "0" to Semaphore 0 1 No change. Right side has no write access to semaphore Left Port Writes "1" to Semaphore 1 0 Right port obtains semaphore token Left Port Writes "0" to Semaphore 1 0 No change. Left port has no write access to semaphore Right Port Writes "1" to Semaphore 0 1 Left port obtains semaphore token Left Port Writes "1" to Semaphore 1 1 Semaphore free Right Port Writes "0" to Semaphore 1 0 Right port has semaphore token Right Port Writes "1" to Semaphore 1 1 Semaphore free Left Port Writes "0" to Semaphore 0 1 Left port has semaphore token Left Port Writes "1" to Semaphore 1 1 Semaphore free NOTES: 1. This table denotes a sequence of events for only one of the eight semaphores on the IDT7015. 2. There are eight semaphore flags written to via I/O0 and read from I/O0-8. These eight semaphores are addressed by A0 - A2. 2954 tbl 17 FUNCTIONAL DESCRIPTION The IDT7015 provides two ports with separate control, address and I/O pins that permit independent access for reads or writes to any location in memory. The IDT7015 has an automatic power down feature controlled by CE. The CE controls on-chip power down circuitry that permits the respective port to go into a standby mode when not selected (CE High). When a port is enabled, access to the entire memory array is permitted. memory location 1FFF and to clear the interrupt flag (INTR), the right port must access memory location 1FFF. The message (9 bits) at 1FFE or 1FFF is user-defined since it is an addressable SRAM location. If the interrupt function is not used, address locations 1FFE and 1FFF are not used as mail boxes but are still part of the random access memory. Refer to Truth Table for the interrupt operation. BUSY LOGIC INTERRUPTS If the user chooses to use the interrupt function, a memory location (mail box or message center) is assigned to each port. The left port interrupt flag (INTL) is asserted when the right port writes to memory location 1FFE where a write is defined as the CE = R/W = VIL per the Truth Table. The left port clears the interrupt by an address location 1FFE access when CER =OER =VIL, R/W is a "don't care". Likewise, the right port interrupt flag (INTR) is asserted when the left port writes to Busy Logic provides a hardware indication that both ports of the RAM have accessed the same location at the same time. It also allows one of the two accesses to proceed and signals the other side that the RAM is “Busy”. The busy pin can then be used to stall the access until the operation on the other side is completed. If a write operation has been attempted from the side that receives a busy indication, the write signal is gated internally to prevent the write from proceeding. The use of busy logic is not required or desirable for all 6.12 16 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MASTER Dual Port RAM BUSY (L) BUSY (L) MASTER Dual Port RAM BUSY (L) CE SLAVE Dual Port RAM BUSY (L) BUSY (R) CE SLAVE Dual Port RAM BUSY (L) BUSY (R) CE BUSY (R) DECODER MILITARY AND COMMERCIAL TEMPERATURE RANGES CE BUSY (R) BUSY (R) 2954 drw 19 Figure 3. Busy and chip enable routing for both width and depth expansion with IDT7015 RAMs. applications. In some cases it may be useful to logically OR the busy outputs together and use any busy indication as an interrupt source to flag the event of an illegal or illogical operation. If the write inhibit function of busy logic is not desirable, the busy logic can be disabled by placing the part in slave mode with the M/S pin. Once in slave mode the BUSY pin operates solely as a write inhibit input pin. Normal operation can be programmed by tying the BUSY pins high. If desired, unintended write operations can be prevented to a port by tying the busy pin for that port low. The busy outputs on the IDT7015 RAM in master mode, are push-pull type outputs and do not require pull up resistors to operate. If these RAMs are being expanded in depth, then the busy indication for the resulting array requires the use of an external AND gate. WIDTH EXPANSION WITH BUSY LOGIC MASTER/SLAVE ARRAYS When expanding an IDT7015 RAM array in width while using busy logic, one master part is used to decide which side of the RAM array will receive a busy indication, and to output that indication. Any number of slaves to be addressed in the same address range as the master, use the busy signal as a write inhibit signal. Thus on the IDT7015 RAM the busy pin is an output if the part is used as a master (M/S pin = H), and the busy pin is an input if the part used as a slave (M/S pin = L) as shown in Figure 3. If two or more master parts were used when expanding in width, a split decision could result with one master indicating busy on one side of the array and another master indicating busy on one other side of the array. This would inhibit the write operations from one port for part of a word and inhibit the write operations from the other port for the other part of the word. The busy arbitration, on a master, is based on the chip enable and address signals only. It ignores whether an access is a read or write. In a master/slave array, both address and chip enable must be valid long enough for a busy flag to be output from the master before the actual write pulse can be initiated with the R/W signal. Failure to observe this timing can result in a glitched internal write inhibit signal and corrupted data in the slave. SEMAPHORES The IDT7015 are extremely fast Dual-Port 8Kx9 Static RAMs with an additional 8 address locations dedicated to binary semaphore flags. These flags allow either processor on the left or right side of the Dual-Port RAM to claim a privilege over the other processor for functions defined by the system designer’s software. As an example, the semaphore can be used by one processor to inhibit the other from accessing a portion of the Dual-Port RAM or any other shared resource. The Dual-Port RAM features a fast access time, and both ports are completely independent of each other. This means that the activity on the left port in no way slows the access time of the right port. Both ports are identical in function to standard CMOS Static RAM and can be read from, or written to, at the same time with the only possible conflict arising from the simultaneous writing of, or a simultaneous READ/WRITE of, a non-semaphore location. Semaphores are protected against such ambiguous situations and may be used by the system program to avoid any conflicts in the non-semaphore portion of the Dual-Port RAM. These devices have an automatic power-down feature controlled by CE, the Dual-Port RAM enable, and SEM, the semaphore enable. The CE and SEM pins control on-chip power down circuitry that permits the respective port to go into standby mode when not selected. This is the condition which is shown in Truth Table where CE and SEM are both high. Systems which can best use the IDT7015 contain multiple processors or controllers and are typically very high-speed systems which are software controlled or software intensive. These systems can benefit from a performance increase offered by the IDT7015's hardware semaphores, which provide a lockout mechanism without requiring complex programming. 6.12 17 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES Software handshaking between processors offers the maximum in system flexibility by permitting shared resources to be allocated in varying configurations. The IDT7015 does not use its semaphore flags to control any resources through hardware, thus allowing the system designer total flexibility in system architecture. An advantage of using semaphores rather than the more common methods of hardware arbitration is that wait states are never incurred in either processor. This can prove to be a major advantage in very high-speed systems. HOW THE SEMAPHORE FLAGS WORK The semaphore logic is a set of eight latches which are independent of the Dual-Port RAM. These latches can be used to pass a flag, or token, from one port to the other to indicate that a shared resource is in use. The semaphores provide a hardware assist for a use assignment method called “Token Passing Allocation.” In this method, the state of a semaphore latch is used as a token indicating that shared resource is in use. If the left processor wants to use this resource, it requests the token by setting the latch. This processor then verifies its success in setting the latch by reading it. If it was successful, it proceeds to assume control over the shared resource. If it was not successful in setting the latch, it determines that the right side processor has set the latch first, has the token and is using the shared resource. The left processor can then either repeatedly request that semaphore’s status or remove its request for that semaphore to perform another task and occasionally attempt again to gain control of the token via the set and test sequence. Once the right side has relinquished the token, the left side should succeed in gaining control. The semaphore flags are active low. A token is requested by writing a zero into a semaphore latch and is released when the same side writes a one to that latch. The eight semaphore flags reside within the IDT7015 in a separate memory space from the Dual-Port RAM. This address space is accessed by placing a low input on the SEM pin (which acts as a chip select for the semaphore flags) and using the other control pins (Address, OE, and R/W) as they would be used in accessing a standard static RAM. Each of the flags has a unique address which can be accessed by either side through address pins A0 – A2. When accessing the semaphores, none of the other address pins has any effect. When writing to a semaphore, only data pin D0 is used. If a low level is written into an unused semaphore location, that flag will be set to a zero on that side and a one on the other side (see Table III). That semaphore can now only be modified by the side showing the zero. When a one is written into the same location from the same side, the flag will be set to a one for both sides (unless a semaphore request from the other side is pending) and then can be written to by both sides. The fact that the side which is able to write a zero into a semaphore subsequently locks out writes from the other side is what makes semaphore flags useful in interprocessor communications. (A thorough discussing on the use of this feature follows shortly.) A zero written into the same location from the other side will be stored in the semaphore request latch for that side until the semaphore is freed by the first side. When a semaphore flag is read, its value is spread into all data bits so that a flag that is a one reads as a one in all data bits and a flag containing a zero reads as all zeros. The read value is latched into one side’s output register when that side's semaphore select (SEM) and output enable (OE) signals go active. This serves to disallow the semaphore from changing state in the middle of a read cycle due to a write cycle from the other side. Because of this latch, a repeated read of a semaphore in a test loop must cause either signal (SEM or OE) to go inactive or the output will never change. A sequence WRITE/READ must be used by the semaphore in order to guarantee that no system level contention will occur. A processor requests access to shared resources by attempting to write a zero into a semaphore location. If the semaphore is already in use, the semaphore request latch will contain a zero, yet the semaphore flag will appear as one, a fact which the processor will verify by the subsequent read (see Table III). As an example, assume a processor writes a zero to the left port at a free semaphore location. On a subsequent read, the processor will verify that it has written successfully to that location and will assume control over the resource in question. Meanwhile, if a processor on the right side attempts to write a zero to the same semaphore flag it will fail, as will be verified by the fact that a one will be read from that semaphore on the right side during subsequent read. Had a sequence of READ/WRITE been used instead, system contention problems could have occurred during the gap between the read and write cycles. It is important to note that a failed semaphore request must be followed by either repeated reads or by writing a one into the same location. The reason for this is easily understood by looking at the simple logic diagram of the semaphore flag in Figure 4. Two semaphore request latches feed into a semaphore flag. Whichever latch is first to present a zero to the semaphore flag will force its side of the semaphore flag low and the other side high. This condition will continue until a one is written to the same semaphore request latch. Should the other side’s semaphore request latch have been written to a zero in the meantime, the semaphore flag will flip over to the other side as soon as a one is written into the first side’s request latch. The second side’s flag will now stay low until its semaphore request latch is written to a one. From this it is easy to understand that, if a semaphore is requested and the processor which requested it no longer needs the resource, the entire system can hang up until a one is written into that semaphore request latch. The critical case of semaphore timing is when both sides request a single token by attempting to write a zero into it at the same time. The semaphore logic is specially designed to resolve this problem. If simultaneous requests are made, the logic guarantees that only one side receives the token. If one side is earlier than the other in making the request, the first side to make the request will receive the token. If both requests arrive at the same time, the assignment will be arbitrarily made to one port or the other. One caution that should be noted when using semaphores is that semaphores alone do not guarantee that access to a 6.12 18 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES resource is secure. As with any powerful programming technique, if semaphores are misused or misinterpreted, a software error can easily happen. Initialization of the semaphores is not automatic and must be handled via the initialization program at power-up. Since any semaphore request flag which contains a zero must be reset to a one, all semaphores on both sides should have a one written into them at initialization from both sides to assure that they will be free when needed. USING SEMAPHORES—SOME EXAMPLES Perhaps the simplest application of semaphores is their application as resource markers for the IDT7015’s Dual-Port RAM. Say the 8K x 9 RAM was to be divided into two 4K x 9 blocks which were to be dedicated at any one time to servicing either the left or right port. Semaphore 0 could be used to indicate the side which would control the lower section of memory, and Semaphore 1 could be defined as the indicator for the upper section of memory. To take a resource, in this example the lower 4K of Dual-Port RAM, the processor on the left port could write and then read a zero in to Semaphore 0. If this task were successfully completed (a zero was read back rather than a one), the left processor would assume control of the lower 4K. Meanwhile the right processor was attempting to gain control of the resource after the left processor, it would read back a one in response to the zero it had attempted to write into Semaphore 0. At this point, the software could choose to try and gain control of the second 4K section by writing, then reading a zero into Semaphore 1. If it succeeded in gaining control, it would lock out the left side. Once the left side was finished with its task, it would write a one to Semaphore 0 and may then try to gain access to Semaphore 1. If Semaphore 1 was still occupied by the right side, the left side could undo its semaphore request and perform other tasks until it was able to write, then read a zero into Semaphore 1. If the right processor performs a similar task with Semaphore 0, this protocol would allow the two processors to swap 4K blocks of Dual-Port RAM with each other. The blocks do not have to be any particular size and can even be variable, depending upon the complexity of the software using the semaphore flags. All eight semaphores could be used to divide the Dual-Port RAM or other shared resources into eight parts. Semaphores can even be assigned different meanings on different sides rather than being given a common meaning as was shown in the example above. Semaphores are a useful form of arbitration in systems like disk interfaces where the CPU must be locked out of a section of memory during a transfer and the I/O device cannot tolerate any wait states. With the use of semaphores, once the two devices has determined which memory area was “off-limits” to the CPU, both the CPU and the I/O devices could access their assigned portions of memory continuously without any wait states. Semaphores are also useful in applications where no memory “WAIT” state is available on one or both sides. Once a semaphore handshake has been performed, both processors can access their assigned RAM segments at full speed. Another application is in the area of complex data structures. In this case, block arbitration is very important. For this application one processor may be responsible for building and updating a data structure. The other processor then reads and interprets that data structure. If the interpreting processor reads an incomplete data structure, a major error condition may exist. Therefore, some sort of arbitration must be used between the two different processors. The building processor arbitrates for the block, locks it and then is able to go in and update the data structure. When the update is completed, the data structure block is released. This allows the interpreting processor to come back and read the complete data structure, thereby guaranteeing a consistent data structure. L PORT R PORT SEMAPHORE REQUEST FLIP FLOP D0 D SEMAPHORE REQUEST FLIP FLOP Q Q WRITE D D0 WRITE SEMAPHORE READ SEMAPHORE READ 2954 drw 20 Figure 4. IDT7015 Semaphore Logic 6.12 19 IDT7015S/L HIGH-SPEED 8K x 9 DUAL-PORT STATIC RAM MILITARY AND COMMERCIAL TEMPERATURE RANGES ORDERING INFORMATION IDT XXXXX Device Type A 999 A A Power Speed Package Process/ Temperature Range Blank Commercial (0°C to +70°C) B Military (–55°C to +125°C) Compliant to MIL-STD-883, Class B PF G J 80-pin TQFP (PN80-1) 68-pin PGA (G68-1) 68-pin PLCC (J68-1) 12 15 17 20 25 35 Commercial Only Commercial Only Commercial Only S L Standard Power Low Power 7015 72K (8K x 9) Dual-Port RAM Speed in nanoseconds 2954 drw 21 6.12 20