AD ADM222ANZ High-speed, 5 v, 0.1 f cmos rs-232 drivers/receiver Datasheet

a
High-Speed, 5 V, 0.1 F
CMOS RS-232 Drivers/Receivers
ADM222/ADM232A/ADM242
FUNCTIONAL BLOCK DIAGRAM
FEATURES
200 kB/s Transmission Rate
Small (0.1 F) Charge Pump Capacitors
Single 5 V Power Supply
Meets All EIA-232-E and V.28 Specifications
Two Drivers and Two Receivers
On-Board DC-DC Converters
9 V Output Swing with 5 V Supply
30 V Receiver Input Levels
Pin Compatible with MAX222/MAX232A/MAX242
5V INPUT
0.1F
C1+
0.1F
C1–
C2+
0.1F
VCC
+5V TO +10V
V+
VOLTAGE DOUBLER
+5V TO –10V
VOLTAGE INVERTER V–
0.1F
C2–
APPLICATIONS
Computers
Peripherals
Modems
Printers
Instruments
TTL/CMOS
INPUTS*
TTL/CMOS
OUTPUTS
T1IN
T1
T1OUT
T2IN
T2
T2OUT
R1OUT
R1
R1IN
R2OUT
R2
R2IN
ADM2xx
GENERAL DESCRIPTION
The ADM222, ADM232A, ADM242 are a family of high-speed
RS-232 line drivers/receivers offering transmission rates up to
200 kB/s. Operating from a single 5 V power supply, a highly
efficient on-chip charge pump using small (0.1 µF) external
capacitors allows RS-232 bipolar levels to be developed. Two
RS-232 drivers and two RS-232 receivers are provided on
each device.
The devices are fabricated on BiCMOS, an advanced mixed
technology process that combines low power CMOS with highspeed bipolar circuitry. This allows for transmission rates up to
200 kB/s, yet minimizes the quiescent power supply current to
under 5 mA.
The ADM232A is a pin-compatible, high-speed upgrade for the
AD232 and for the ADM232L. It is available in 16-lead DIP
and in both narrow and wide surface-mount (SOIC) packages.
The ADM222 contains an additional shutdown (SHDN) function that may be used to disable the device, thereby reducing the
supply current to 0.1 µA. During shutdown, all transmit/receive
0.1F
EN
GND
SHDN
RS-232
OUTPUTS
RS-232
INPUTS**
(ADM242)
(ADM222, ADM242)
* INTERNAL 400k PULL-UP RESISTOR
ON EACH TTL/CMOS INPUT
** INTERNAL 5k PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
functions are disabled. The ADM222 is available in 18-lead
DIP and in a wide surface-mount (SOIC) package.
The ADM242 combines both shutdown (SHDN) and enable
(EN) functions. The shutdown function reduces the supply
current to 0.1 mA. During shutdown, the transmitters are disabled but the receivers continue to operate normally. The
enable function allows the receiver outputs to be disabled
thereby facilitating sharing a common bus. The ADM242 is
available in 18-lead DIP and in a wide surface-mount (SOIC)
package.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/461-3113
© Analog Devices, Inc., 2010
(VCC = 5 V 10%. C1–C4 = 0.1 F; all specMIN to TMAX unless otherwise noted.)
ADM222/ADM232A/ADM242–SPECIFICATIONS ifications T
Parameter
Min
Typ
RS-232 TRANSMITTERS
Output Voltage Swing
±5
±9
2.4
1.7
1.7
12
Input Logic Threshold Low, VINL
Input Logic Threshold High, VINH
Logic Pull-Up Current
Data Rate
Output Resistance
Output Short Circuit Current (Instantaneous)
RS-232 RECEIVERS
RS-232 Input Voltage Range
RS-232 Input Threshold Low
RS-232 Input Threshold High
RS-232 Input Hysteresis
RS-232 Input Resistance
TTL/CMOS Output Voltage Low, VOL
TTL/CMOS Output Voltage High, VOH
TTL/CMOS Output Short-Circuit Current
TTL/CMOS Output Short-Circuit Current
TTL/CMOS Output Leakage Current
EN Input Threshold Low, VINL
EN Input Threshold High, VINH
AC CHARACTERISTICS
Transition Region Slew Rate
Transmitter Propagation Delay TTL to RS-232
Receiver Propagation Delay RS-232 to TTL
Receiver Output Enable Time
Receiver Output Disable Time
Transmitter Output Enable Time
Transmitter Output Disable Time
Transmitter + to – Propagation Delay Difference
Receiver + to – Propagation Delay Difference
0.8
40
200
300
± 10
–30
0.8
0.2
3
3.5
–2
10
2.0
POWER SUPPLY
Power Supply Current
Shutdown Power Supply Current
SHDN Input Leakage Current
SHDN Input Threshold Low, VINL
SHDN Input Threshold High, VINH
Max
+30
1.2
1.6
0.4
5
0.05
2.4
1.0
7
0.4
–85
35
± 0.05
± 10
Unit
Test Conditions/Comments
V
All Transmitter Outputs Loaded with
3 kΩ to Ground
TIN
TIN
TIN = 0 V
V
V
µA
kB/s
Ω
mA
V
V
V
V
kΩ
V
V
mA
mA
µA
VCC = V+ = V– = 0 V, VOUT = ± 2 V
VCC = 5 V
TA = 0°C to 85°C
IOUT = 3.2 mA
IOUT = –1.0 mA
Source Current (VOUT = GND)*
Sink Current (VOUT = VCC)*
SHDN = GND/EN = VCC
0 V ≤ VOUT ≤ VCC
1.4
1.4
0.8
V
V
4
13
0.1
8
mA
mA
µA
µA
V
V
No Load
3 kΩ Load on Both Outputs
CL = 50 pF to 1000 pF, RL = 3 kΩ to 7 kΩ
Measured from +3 V to –3 V or –3 V to +3 V
tPHLT
tPLHT
tPHLR
tPLHR
tER
tDR
SHDN Goes High
SHDN Goes Low
10
±1
0.8
2.0
1.4
1.4
3
8
30
V/µs
0.85
1.0
0.1
0.3
125
160
250
3.5
150
200
3.5
3.5
0.5
0.5
500
500
µs
µs
µs
µs
ns
ns
µs
µs
ns
ns
*Guaranteed by design, not production tested.
Specifications subject to change without notice.
–2–
REV. B
ADM222/ADM232A/ADM242
ABSOLUTE MAXIMUM RATINGS*
(TA = 25°C unless otherwise noted)
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
V+ . . . . . . . . . . . . . . . . . . . . . . . . . . . (VCC – 0.3 V) to +13 V
V– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3 V to –13 V
Input Voltages
TIN . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to (VCC + 0.3 V)
RIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 30 V
Output Voltages
TOUT . . . . . . . . . . . . . . . . . . . (V+, +0.3 V) to (V–, –0.3 V)
ROUT . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to (VCC + 0.3 V)
Short Circuit Duration
TOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
Power Dissipation N-16 . . . . . . . . . . . . . . . . . . . . . . 400 mW
(Derate 7.5 mW/°C above 70°C)
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°C/W
Power Dissipation R-16N . . . . . . . . . . . . . . . . . . . . . 400 mW
(Derate 7 mW/°C above 70°C)
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°C/W
Power Dissipation R-16W . . . . . . . . . . . . . . . . . . . . . 400 mW
(Derate 7 mW/°C above 70°C)
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°CW
Power Dissipation N-18 . . . . . . . . . . . . . . . . . . . . . . 400 mW
(Derate 7 mW/°C above 70°C)
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°C/W
Power Dissipation R-18W . . . . . . . . . . . . . . . . . . . . . 400 mW
(Derate 7 mW/°C above 70°C)
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . . . 80°C/W
Operating Temperature Range
Industrial (A Version) . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . 300°C
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C
*This is a stress rating only and functional operation of the device at these or any
other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended
periods of time may affect reliability.
Test Circuits
3V
3V
VIN
VIN
t PLHT
0V
t PHLR
t PHLT
t PLHR
VCC
V+
VOUT
VOUT
0V
50%
GND
V–
Figure 1. Transmitter Propagation Delay Timing
Figure 3. Receiver Propagation Delay Timing
3V
EN
INPUT
3V
0V
EN
INPUT
0V
t DR
t ER
VOH
VOH – 0.5V
3.5V
RECEIVER
OUTPUT
RECEIVER
OUTPUT
VOL + 0.5V
0.8V
VOL
Figure 2. Receiver Enable Timing
REV. B
Figure 4. Receiver Disable Timing
–3–
ADM222/ADM232A/ADM242
PIN FUNCTION DESCRIPTION
VOUT
VIN
3k
50pF
SHDN
Mnemonic
Function
VCC
V+
Power Supply Input, 5 V ± 10%.
Internally generated positive supply (+10 V
nominal).
Internally generated negative supply (–10 V
nominal).
Ground Pin. Must be connected to 0 V.
External capacitor 1, (+ terminal) is connected
to this pin.
External capacitor 1, (– terminal) is connected
to this pin.
External capacitor 2, (+ terminal) is connected
to this pin.
External capacitor 2, (– terminal) is connected
to this pin.
Transmitter (Driver) Inputs. These inputs accept
TTL/CMOS levels. An internal 400 kΩ pull-up
resistor to VCC is connected on each input.
Transmitter (Driver) Outputs. These are RS-232
levels (typically ± 9 V).
Receiver Inputs. These inputs accept RS-232
signal levels. An internal 5 kΩ pull-down resistor
to GND is connected on each of these inputs.
Receiver Outputs. These are TTL/CMOS levels.
No Connect. No connections are required to
this pin.
(ADM242 Only) Active Low Digital Input. May
be used to enable or disable (three-state) both
receiver outputs.
(ADM222 and ADM242) Active Low Digital
Input. May be used to disable the device so that
the power consumption is minimized. On the
ADM222 all drivers and receivers are disabled.
On the ADM242 the drivers are disabled but the
receivers remain enabled.
V–
Figure 5. Shutdown Test Circuit
GND
C1+
3V
SHDN
INPUT
C1–
0V
C2+
t DT
C2–
V+
+ 5V
TIN
TRANSMITTER
OUTPUT
TOUT
– 5V
RIN
V–
Figure 6. Transmitter Shutdown Disable Timing
ROUT
NC
5V INPUT
EN
C5
0.1F
6.3V
2
C1
0.1F
4
5
C2
0.1F
T1IN
TTL/CMOS
INPUTS*
T2IN
6
C1+
C1–
C2+
17
VCC
3
+5V TO +10V
V+
VOLTAGE DOUBLER
+5V TO –10V
7
VOLTAGE INVERTER V–
C2–
12
15
T1
11
8
T2
13
R1OUT
TTL/CMOS
OUTPUTS
R1
10
R2OUT
R2
ADM222
14
9
18
C3
0.1F
SHDN
C4
0.1F
T1OUT
T2OUT
RS-232
OUTPUTS
R1IN
R2IN
RS-232
INPUTS**
18
17
VCC
V+ 3
16
GND
15
T1OUT
C1– 4
ADM222
SHDN
TOP VIEW 14 R1IN
(Not to Scale)
C2– 6
13 R1OUT
C2+ 5
SHDN
GND
16
NC 1
C1+ 2
* INTERNAL 400k PULL-UP RESISTOR
ON EACH TTL/CMOS INPUT
** INTERNAL 5k PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
V– 7
12
T1IN
T2OUT 8
11
T2IN
R2IN 9
10
R2OUT
NC = NO CONNECT
Figure 7. ADM222 Typical Operating Circuit
Figure 8. ADM222 DIP and SOIC Pin Configurations
–4–
REV. B
ADM222/ADM232A/ADM242
EN 1
C1+ 1
V+ 2
C2+ 4
ADM232A
17 VCC
16 GND
V+ 3
15 GND
C1– 3
18 SHDN
C1+ 2
16 VCC
14 T1OUT
C1– 4
13 R1IN
C2+ 5
ADM242
TOP VIEW
C2– 5 (Not to Scale) 12 R1OUT
V– 6
11 T1IN
V– 7
12 T1IN
T2OUT 7
10 T2IN
T2OUT 8
11 T2IN
R2IN 8
9
R2IN 9
R2OUT
Figure 9. ADM232A DIP/SOIC Pin Configuration
10 R2OUT
Figure 11. ADM242 DIP/SOIC Pin Configuration
5V INPUT
5V INPUT
C5
0.1F
6.3V
1
C1
0.1F
3
4
C2
0.1F
T1IN
TTL/CMOS
INPUTS*
T2IN
5
C1+
C1–
C2+
16
VCC
2
+5V TO +10V
V+
VOLTAGE DOUBLER
+5V TO –10V
6
VOLTAGE INVERTER V–
C2–
11
14
T1
10
7
T2
12
R2OUT
C5
0.1F
6.3V
C3
0.1F
2
C1
0.1F
R1
9
R2
13
8
C2
0.1F
C4
0.1F
T1IN
T1OUT
T2OUT
TTL/CMOS
INPUTS*
RS-232
OUTPUTS
R2IN
C1–
C2+
17
VCC
3
+5V TO +10V
V+
VOLTAGE DOUBLER
+5V TO –10V
7
VOLTAGE INVERTER V–
C2–
12
15
T1
11
8
T2
14
R1OUT
RS-232
INPUTS**
TTL/CMOS
OUTPUTS
R2OUT
EN
GND
15
T2IN
6
C1+
13
R1IN
ADM232A
R1
C3
0.1F
C4
0.1F
T1OUT
T2OUT
R1IN
9
10
R2IN
R2
1
ADM242
18
RS-232
OUTPUTS
RS-232
INPUTS**
SHDN
GND
16
* INTERNAL 400k PULL-UP RESISTOR
ON EACH TTL/CMOS INPUT
** INTERNAL 5k PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
* INTERNAL 400k PULL-UP RESISTOR
ON EACH TTL/CMOS INPUT
** INTERNAL 5k PULL-DOWN RESISTOR
ON EACH RS-232 INPUT
Figure 10. ADM232A Typical Operating Circuit
REV. B
4
5
R1OUT
TTL/CMOS
OUTPUTS
15 T1OUT
TOP VIEW 14 R1IN
(Not to Scale)
C2– 6
13 R1OUT
Figure 12. ADM242 Typical Operating Circuit
–5–
ADM222/ADM232A/ADM242 –Typical Performance Characteristics
15
15
10
10
V+
Tx O/P VOLTAGE – V
Tx O/P HI
V+, V– – V
5
0
–5
5
0
–5
Tx O/P LO
V–
–10
–10
–15
0
5
10
15
20
LOAD CURRENT – mA
25
–15
30
TPC 1. Charge Pump V+, V– vs. Current
0
2
4
6
8
10
LOAD CURRENT – mA
12
14
TPC 4. Transmitter Output Voltage vs. Current
9
TRANSMITTER OUTPUT VOLTAGE – V
115kBps
7
230kBps
5
A4
0.010V
115kBps
3
100
90
1
–1
–3
460kBps
10
–5
0%
460kBps
–7
–9
230kBps
0
500
1000
1500
2000
LOAD CAPACITANCE – pF
2500
5V
5V
100s
3000
TPC 2. Transmitter Baud Rate vs. Load Capacitance
TPC 5. Charge Pump V+, V– Exiting Shutdown
T
T
: 6.2V
: 140ns
@: –3.5V
: 6.0V
: 600ns
@: –2.9V
T
CH1
T
10.0V
CH2
5.00V
M 1.00s
CH2
–6.4V
CH1
TPC 3. Transmitter Unloaded Slew Rate
10.0V
CH2
5.00V
M 1.00s
CH2
–6.4V
TPC 6. Transmitter Fully Loaded Slew Rate
–6–
REV. B
ADM222/ADM232A/ADM242
GENERAL INFORMATION
The ADM222/ADM232A/ADM242 are high-speed RS-232
drivers/receivers requiring a single digital 5 V supply. The RS-232
standard requires transmitters that will deliver ± 5 V minimum
on the transmission channel and receivers that can accept signal
levels down to ± 3 V. The parts achieve this by integrating stepup voltage converters and level-shifting transmitters and receivers
onto the same chip. CMOS technology is used to keep the
power dissipation to an absolute minimum. All devices contain an internal charge pump voltage doubler and a voltage
inverter that generates ± 10 V from the 5 V input. Four external 0.1 µF capacitors are required for the internal charge pump
voltage converter.
The ADM222/ADM232A/ADM242 is a modification, enhancement and improvement to the AD230-AD241 family and
derivatives thereof. It is essentially plug-in-compatible and does
not have materially different applications.
CIRCUIT DESCRIPTION
The internal circuitry consists of four main sections. These are:
Charge Pump Voltage Converter
TTL/CMOS to RS-232 Transmitters
RS-232 to TTL/CMOS Receivers
Enable and Shutdown Functions.
Charge Pump DC-DC Voltage Converter
The Charge Pump Voltage converter consists of an oscillator
and a switching matrix. The converter generates a ± 10 V supply
from the input 5 V level. This is done in two stages using a
switched capacitor technique. The 5 V input supply is doubled
to 10 V using capacitor C1 as the charge storage element. The
–10 V level is also generated from the input 5 V supply using C1
and C2 as the storage elements.
Capacitors C3 and C4 are used to reduce the output ripple.
Their values are not critical and can be reduced if higher levels
of ripple are acceptable. The charge pump capacitors C1 and
C2 may also be reduced at the expense of higher output impedance on the V+ and V– supplies.
The input threshold levels are both TTL- and CMOS-compatible with the switching threshold set at VCC/4. With a nominal
VCC = 5 V, the switching threshold is 1.25 V typical. Unused
inputs may be left unconnected, as an internal 400 kΩ pull-up
resistor pulls them high forcing the outputs into a low state.
As required by the RS-232 standard, the slew rate is limited to
less than 30 V/µs without the need for an external slew limiting
capacitor, and the output impedance in the power-off state is
greater than 300 Ω.
Receiver Section
The receivers are inverting level-shifters that accept RS-232
input levels (± 3 V to ± 15 V) and translate them into 5 V TTL/
CMOS levels. The inputs have internal 5 kΩ pull-down resistors
to ground and are also protected against overvoltages of up to
± 30 V. The guaranteed switching thresholds are 0.8 V minimum and 2.4 V maximum, which are well within the ± 3 V
RS-232 requirement. The low level threshold is deliberately
positive as it ensures that an unconnected input will be interpreted as a low level.
The receivers have Schmitt trigger input with a hysteresis level
of 0.5 V. This ensures error-free reception for both noisy inputs
and for inputs with slow transition times
Enable and Shutdown Functions
On the ADM222, both receivers are fully disabled during
shutdown.
On the ADM242, both receivers continue to operate normally.
This function is useful for monitoring activity so that when it
occurs, the device can be taken out of the shutdown mode.
The ADM242 also contains a receiver enable function (EN)
which can be used to fully disable the receivers, independent
of SHDN.
APPLICATIONS INFORMATION
A selection of typical operating circuits is shown in TPCs 1–6
and Figure 13.
The V+ and V– supplies may also be used to power external
circuitry if the current requirements are small. Please refer to
the typical performance characteristics which shows the V+, V–
output voltage vs. current.
A1
2.0V
5V
5V
100
90
In the shutdown mode the charge pump is disabled and V+
decays to VCC while V– decays to 0 V.
10
Transmitter (Driver) Section
0%
The Drivers convert TTL/CMOS input levels into RS-232
output levels. With VCC = 5 V and driving a typical RS-232
load, the output voltage swing is ± 9 V. Even under worst-case
conditions the drivers are guaranteed to meet the ± 5 V RS-232
minimum requirement.
REV. B
5s
Figure 13. Transmitter Output Disable Timing
–7–
ADM222/ADM232A/ADM242
OUTLINE DIMENSIONS
0.800 (20.32)
0.790 (20.07)
0.780 (19.81)
16
9
1
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
8
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.210 (5.33)
MAX
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
PLANE
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
073106-B
COMPLIANT TO JEDEC STANDARDS MS-001-AB
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 14. 16-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
(N-16)
Dimensions shown in inches and (millimeters)
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
8
1.27 (0.0500)
BSC
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
0.51 (0.0201)
0.31 (0.0122)
10.65 (0.4193)
10.00 (0.3937)
2.65 (0.1043)
2.35 (0.0925)
SEATING
PLANE
0.75 (0.0295)
0.25 (0.0098)
45°
8°
0°
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013- AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
1.27 (0.0500)
0.40 (0.0157)
032707-B
1
Figure 15. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
Dimensions shown in millimeters and (inches)
–8–
REV. B
ADM222/ADM232A/ADM242
10.00 (0.3937)
9.80 (0.3858)
4.00 (0.1575)
3.80 (0.1496)
9
16
1
8
1.27 (0.0500)
BSC
1.75 (0.0689)
1.35 (0.0531)
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
0.10
6.20 (0.2441)
5.80 (0.2283)
SEATING
PLANE
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0197)
0.25 (0.0098)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AC
060606-A
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 16. 16-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-16)
Dimensions shown in millimeters and (inches)
11.75 (0.4626)
11.35 (0.4469)
18
10
7.60 (0.2992)
7.40 (0.2913)
9
2.65 (0.1043)
2.35 (0.0925)
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
10.65 (0.4193)
10.00 (0.3937)
1.27
(0.0500)
BSC
0.51 (0.0201)
0.31 (0.0122)
SEATING
PLANE
0.75 (0.0295)
0.25 (0.0098)
8°
0°
0.33 (0.0130)
0.20 (0.0079)
COMPLIANT TO JEDEC STANDARDS MS-013-AB
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 17. 18-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-18)
Dimensions shown in millimeters and (inches)
REV. B
–9–
45°
1.27 (0.0500)
0.40 (0.0157)
060706-A
1
ADM222/ADM232A/ADM242
0.920 (23.37)
0.900 (22.86)
0.880 (22.35)
18
10
1
9
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.210 (5.33)
MAX
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
PLANE
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.005 (0.13)
MIN
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.430 (10.92)
MAX
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
070706-A
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
Figure 18. 18-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body
(N-18)
Dimensions shown in inches and (millimeters)
ORDERING GUIDE
Model1
ADM222AN
ADM222ANZ
ADM222AR
ADM222ARZ
ADM222ARZ-REEL
ADM232AAN
ADM232AANZ
ADM232AARN
ADM232AARN-REEL
ADM232AARN-REEL7
ADM232AARNZ
ADM232AARNZ-REEL
ADM232AARNZ-REEL7
ADM232AARW
ADM232AARW-REEL
ADM232AARWZ
ADM232AARWZ-REEL
ADM242AN
ADM242ANZ
ADM242AR
ADM242AR-REEL
ADM242ARZ
ADM242ARZ-REEL
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
18-Lead PDIP
18-Lead PDIP
18-Lead SOIC_W
18-Lead SOIC_W
18-Lead SOIC_W
16-Lead PDIP
16-Lead PDIP
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_N
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
16-Lead SOIC_W
18-Lead PDIP
18-Lead PDIP
18-Lead SOIC_W
18-Lead SOIC_W
18-Lead SOIC_W
18-Lead SOIC_W
Package Option
N-18
N-18
RW-18
RW-18
RW-18
N-16
N-16
R-16
R-16
R-16
R-16
R-16
R-16
RW-16
RW-16
RW-16
RW-16
N-18
N-18
RW-18
RW-18
RW-18
RW-18
Z = RoHS Compliant Part.
–10–
REV. B
ADM222/ADM232A/ADM242
REVISION HISTORY
11/10—Rev. A to Rev. B
Updated Outline Dimensions ......................................................... 9
Changes to Ordering Guide .......................................................... 10
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D01213-0-11/10(B)
REV. B
–11–