POWER INDUCTORS Outgassing Compliant Power Inductors AE558PTA ■ High temperature materials allow operation in ambient temperatures up to 155°C. ■ Passes NASA low outgassing specifications ■ Tin-lead (Sn-Pb) termination for the best possible board adhesion ■ Excellent current handling; very low DCR Core material Ferrite Terminations Tin-lead over tin over nickel over phos bronze Weight 1.6 g Ambient temperature –55°C to +105°C with Irms current, +105°C to +155°C with derated current Storage temperature Component: –55°C to +155°C. Tape and reel packaging: –55°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Enhanced crush-resistant packaging 200/7″ reel Plastic tape: 24 mm wide,0.4 mm thick, 16 mm pocket spacing, 5.45 mm pocket depth SRF (MHz) Inductance2 DCR max3 Part number1 ±20% (µH) (mOhm) min typ 4 AE558PTA331MSZ AE558PTA801MSZ AE558PTA102MSZ AE558PTA122MSZ AE558PTA132MSZ AE558PTA152MSZ AE558PTA182MSZ AE558PTA202MSZ AE558PTA222MSZ AE558PTA252MSZ AE558PTA322MSZ AE558PTA402MSZ AE558PTA432MSZ AE558PTA572MSZ 0.33 0.80 1.0 1.2 1.3 1.5 1.8 2.0 2.2 2.5 3.2 4.0 4.3 5.7 4.0 4.0 4.0 6.0 4.0 6.0 6.0 9.0 4.0 7.5 6.0 9.0 7.5 9.0 119 70.0 66.5 63.7 56.7 52.5 49.0 45.5 40.6 38.5 37.1 32.9 30.8 24.5 170 100 95.0 91.0 81.0 75.0 70.0 65.0 58.0 55.0 53.0 47.0 44.0 35.0 Isat (A)5 10% drop 20% drop 30% drop 29.5 24.9 16.5 20.5 12.9 13.5 13.3 15.3 8.9 11.4 7.3 8.3 6.4 5.4 30.0 25.2 17.0 21.0 16.8 14.0 13.8 15.8 9.6 11.8 7.8 8.5 6.8 5.8 30.5 25.6 17.5 21.3 17.2 14.5 14.3 16.2 10.0 12.1 8.5 8.8 7.0 6.0 Irms (A)6 20°C rise 40°C rise 12.5 12.5 12.5 11.0 12.5 11.0 11.0 8.5 12.5 9.0 11.0 8.5 9.0 8.5 16.3 16.3 16.3 15.0 16.3 15.0 15.0 11.5 16.3 12.0 15.0 11.5 12.0 11.5 1. When ordering, please specify testing code: AE558PTA103MSZ Testing: Z = COTS H = Screening per Coilcraft CP-SA-10001 N = Screening per Coilcraft CP-SA-10004 2. Inductance measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A or equivalent. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using an Agilent/HP 8753D network analyzer. 5. Typical DC current at which the inductance drops the specified amount from its value without current. 6. Typical current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document AE535-1 Revised 12/05/12 ® © Coilcraft, Inc. 2012 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 Fax 847-639-1508 Email [email protected] www.coilcraft-cps.com This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information. POWER INDUCTORS AE558PTA Series Typical L vs Frequency Typical L vs Current 7 7 5.7 µH 5 4 3.2 µH 3 2.0 µH 2 5.7 µH 6 Inductance (µH) Inductance (µH) 6 5 4 3.2 µH 3 2.0 µH 2 1.3 µH 1.3 µH 1 1 0.8 µH 0.8 µH 0 0.1 1 10 100 Frequency (MHz) 0 0.1 Irms Derating Current (A) 10 • 110 2 3 Terminal 3 is for mounting stability only. 0.402 ±0.008 10,2 ±0,2 100 100 1 0.433 ±0.008 11,0 ±0,2 120 90 80 70 60 0.205 max 5,20 50 40 25°C Percent of rated Irms 1 30 20 0.075 ±0.004 1,90 ±0,1 10 0 -55 -40 -20 0 20 40 60 80 100 120 140 160 Ambient temperature (°C) 0.075 ±0.004 1,90 ±0,1 Suggested Land Pattern 0.083 ±0.004 2,10 ±0,1 1 0.152 3,85 0.083 ±0.004 2,10 ±0,1 0.083 ±0.004 2,10 ±0,1 0.118 3,00 0.091 2,30 Dimensions are in 3 0.215 5,47 0.134 3,40 2 inches mm Document AE535-2 Revised 12/05/12 ® © Coilcraft, Inc. 2012 0.118 0.125 3,00 3,18 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 Fax 847-639-1508 Email [email protected] www.coilcraft-cps.com This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information.