ADC1004S030/040/050 Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz Rev. 04 — 2 July 2012 Product data sheet 1. General description The ADC1004S030/040/050 are a family of 10-bit high-speed low-power Analog-to-Digital Converters (ADC) for professional video and other applications. They convert the analog input signal into 10-bit binary-coded digital signals at a maximum sampling rate of 50 MHz. All digital inputs and outputs are Transistor-Transistor Logic (TTL) and CMOS compatible, although a low-level sine wave clock input signal is allowed. The device requires an external source to drive its reference ladder. If the application requires that the reference is driven via internal sources, Integrated Device Technology recommends you use one of the ADC1003S030/040/050 family. 2. Features 10-bit resolution Sampling rate up to 50 MHz DC sampling allowed One clock cycle conversion only High signal-to-noise ratio over a large analog input frequency range (9.4 effective bits at 4.43 MHz full-scale input at fclk = 40 MHz) No missing codes guaranteed In-Range (IR) CMOS output TTL and CMOS levels compatible digital inputs 3 V to 5 V CMOS digital outputs Low-level AC clock input signal allowed External reference voltage regulator Power dissipation only 175 mW (typical) Low analog input capacitance, no buffer amplifier required No sample-and-hold circuit required 3. Applications Video data digitizing Radar Transient signal analysis modulators Medical imaging Barcode scanner Global Positioning System (GPS) receiver ® ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz Cellular base stations 4. Quick reference data Table 1. Quick reference data VCCA = V3 to V4 = 4.75 V to 5.25 V; VCCD = V11 to V12 and V28 to V27 = 4.75 V to 5.25 V; VCCO = V13 to V14 = 3.0 V to 5.25 V; AGND and DGND shorted together; Tamb = 0 C to +70 C; typical values measured at VCCA = VCCD = 5 V and VCCO = 3.3 V; Vi(a)(p-p) = 2.0 V;CL = 15 pF and Tamb = 25 C; unless otherwise specified. Symbol Parameter VCCA Min Typ Max Unit analog supply voltage 4.75 5.0 5.25 V VCCD digital supply voltage 4.75 5.0 5.25 V VCCO output supply voltage 3.0 3.3 5.25 V ICCA analog supply current - 18 24 mA ICCD digital supply current - 16 21 mA ICCO output supply current fclk = 40 MHz; ramp input - 1 2 mA INL integral non-linearity fclk = 40 MHz; ramp input - 0.8 2.0 LSB DNL differential non-linearity fclk = 40 MHz; ramp input - 0.5 0.9 LSB fclk(max) maximum clock frequency ADC1004S030TS 30 - - MHz ADC1004S040TS 40 - - MHz ADC1004S050TS 50 - - MHz fclk = 40 MHz; ramp input - 175 247 mW Ptot Conditions total power dissipation 5. Ordering information Table 2. Ordering information Type number Package Sampling frequency (MHz) Name Description Version ADC1004S030TS SSOP28 plastic shrink small outline package; 28 leads; body width 5.3 mm SOT341-1 30 ADC1004S040TS SSOP28 plastic shrink small outline package; 28 leads; body width 5.3 mm SOT341-1 40 ADC1004S050TS SSOP28 plastic shrink small outline package; 28 leads; body width 5.3 mm SOT341-1 50 ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 2 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz 6. Block diagram VCCA CLK VCCD2 OE 3 1 11 10 2 CLOCK DRIVER RT TC 9 25 D9 MSB 24 D8 23 D7 22 D6 Rlad 21 D5 VI 8 RM 7 analog voltage input ANALOG - TO - DIGITAL CONVERTER CMOS OUTPUTS LATCHES 20 D4 data outputs 19 D3 18 D2 17 D1 16 D0 RB 13 6 ADC1004S030/040/050 CMOS OUTPUT IN-RANGE LATCH 26 28 4 12 14 27 AGND DGND2 OGND DGND1 analog ground Fig 1. digital ground output ground digital ground LSB VCCO IR output VCCD1 014aaa336 Block diagram ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 3 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz 7. Pinning information 7.1 Pinning CLK 1 28 VCCD1 TC 2 27 DGND1 VCCA 3 26 IR AGND 4 25 D9 n.c. 5 24 D8 RB 6 23 D7 RM 7 VI 8 RT 9 20 D4 OE 10 19 D3 VCCD2 11 18 D2 DGND2 12 17 D1 VCCO 13 16 D0 OGND 14 15 n.c. ADC1004S 050TS 22 D6 21 D5 014aaa337 Fig 2. Pin configuration 7.2 Pin description Table 3. Pin description Symbol Pin Description CLK 1 clock input TC 2 two’s complement input (active LOW) VCCA 3 analog supply voltage (5 V) AGND 4 analog ground n.c. 5 not connected RB 6 reference voltage BOTTOM input RM 7 reference voltage MIDDLE VI 8 analog input voltage RT 9 reference voltage TOP input OE 10 output enable input (CMOS level input, active LOW) VCCD2 11 digital supply voltage 2 (5 V) DGND2 12 digital ground 2 VCCO 13 supply voltage for output stages (3 V to 5 V) OGND 14 output ground n.c. 15 not connected D0 16 data output; bit 0 (Least Significant Bit (LSB)) D1 17 data output; bit 1 D2 18 data output; bit 2 D3 19 data output; bit 3 ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 4 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz Table 3. Pin description …continued Symbol Pin Description D4 20 data output; bit 4 D5 21 data output; bit 5 D6 22 data output; bit 6 D7 23 data output; bit 7 D8 24 data output; bit 8 D9 25 data output; bit 9 (Most Significant Bit (MSB)) IR 26 in-range data output DGND1 27 digital ground 1 VCCD1 28 digital supply voltage 1 (5 V) 8. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Min Max Unit VCCA analog supply voltage Conditions [1] 0.3 +7.0 V VCCD digital supply voltage [1] 0.3 +7.0 V VCCO output supply voltage [1] 0.3 +7.0 V VCC supply voltage difference VCCA VCCD 0.1 +1.0 V VCCA VCCO 0.1 +4.0 V VCCD VCCO 0.1 +4.0 V VI input voltage referenced to AGND 0.3 +7.0 V Vi(clk)(p-p) peak-to-peak clock input voltage referenced to DGND - VCCD V IO output current - 10 mA Tstg storage temperature 55 +150 C Tamb ambient temperature 40 +85 C Tj junction temperature - 150 C [1] The supply voltages VCCA, VCCD and VCCO may have any value between 0.3 V and +7.0 V provided that the supply voltage differences VCC are respected. 9. Thermal characteristics Table 5. Thermal characteristics Symbol Parameter Conditions Typ Unit Rth(j-a) thermal resistance from junction to ambient in free air 110 K/W ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 5 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz 10. Characteristics Table 6. Characteristics VCCA = V3 to V4 = 4.75 V to 5.25 V; VCCD = V11 to V12 and V28 to V27 = 4.75 V to 5.25 V; VCCO = V13 to V14 = 3.0 V to 5.25 V; AGND and DGND shorted together; Tamb = 0 C to +70 C; typical values measured at VCCA = VCCD = 5 V and VCCO = 3.3 V; CL = 15 pF and Tamb = 25 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Supply VCCA analog supply voltage 4.75 5.0 5.25 V VCCD digital supply voltage 4.75 5.0 5.25 V VCCO output supply voltage 3.0 3.3 5.25 V VCC supply voltage difference VCCA VCCD 0.20 - +0.20 V VCCA VCCO 0.20 - +2.25 V VCCD VCCO 0.20 - +2.25 V ICCA analog supply current - 18 24 mA ICCD digital supply current - 16 21 mA ICCO output supply current fclk = 40 MHz; ramp input - 1 2 mA Ptot total power dissipation fclk = 40 MHz; ramp input - 175 247 mW Inputs Clock input CLK (referenced to DGND)[1] VIL LOW-level input voltage 0 - 0.8 V VIH HIGH-level input voltage 2 - VCCD V IIL LOW-level input current Vclk = 0.8 V 1 - +1 A IIH HIGH-level input current Vclk = 2 V - 2 10 A Zi input impedance fclk = 40 MHz - 2 - k Ci input capacitance - 2 - pF Inputs OE and TC (referenced to DGND); see Table 8 VIL LOW-level input voltage 0 - 0.8 V VIH HIGH-level input voltage 2 - VCCD V IIL LOW-level input current VIL = 0.8 V 1 - - A IIH HIGH-level input current VIH = 2 V - - 1 A VI (analog input voltage referenced to AGND) IIL LOW-level input current VI = VRB = 1.3 V - 0 - A IIH HIGH-level input current VI = VRT = 3.67 V - 35 - A Zi input impedance fi = 4.43 MHz - 8 - k Ci input capacitance - 5 - pF Reference voltages for the resistor ladder; see Table 7 VRB voltage on pin RB 1.2 1.3 2.45 V VRT voltage on pin RT 3.2 3.67 VCCA 0.8 V Vref(dif) differential reference voltage VRT VRB 2.0 2.37 3.0 V Iref reference current VRT VRB = 2.37 - 9.7 - mA ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 6 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz Table 6. Characteristics …continued VCCA = V3 to V4 = 4.75 V to 5.25 V; VCCD = V11 to V12 and V28 to V27 = 4.75 V to 5.25 V; VCCO = V13 to V14 = 3.0 V to 5.25 V; AGND and DGND shorted together; Tamb = 0 C to +70 C; typical values measured at VCCA = VCCD = 5 V and VCCO = 3.3 V; CL = 15 pF and Tamb = 25 C; unless otherwise specified. Symbol Parameter Min Typ Max Unit Rlad ladder resistance - 245 - TCRlad ladder resistor temperature coefficient - 456 - m/K Voffset offset voltage Vi(a)(p-p) Conditions BOTTOM; VRT VRB = 2.37 [2] - 175 - mV TOP; VRT VRB = 2.37 [2] - 175 - mV [3] 1.7 2.02 2.55 V peak-to-peak analog input voltage Digital outputs D9 to D0 and IR (referenced to OGND) VOL LOW-level output voltage IOL = 1 mA 0 - 0.5 V VOH HIGH-level output voltage IOH = 1 mA VCCO 0.5 - VCCO V IO output current in 3-state mode; 0.5 V < VO < VCCO 20 - +20 A ADC1004S030TS 30 - - MHz ADC1004S040TS 40 - - MHz ADC1004S050TS 50 - - MHz Switching characteristics; Clock input CLK; see Figure 4[1] fclk(max) maximum clock frequency tw(clk)H HIGH clock pulse width full effective bandwidth 8.5 - - ns tw(clk)L LOW clock pulse width full effective bandwidth 5.5 - - ns Analog signal processing Linearity INL integral non-linearity fclk = 40 MHz; ramp input - 0.8 2.0 LSB DNL differential non-linearity fclk = 40 MHz; ramp input - 0.5 0.9 LSB Eoffset offset error middle code; VRB = 1.3 V; VRT = 3.67 V - 1 - LSB EG gain error from device to device; VRB = 1.3 V; VRT = 3.67 V [4] - 0.1 - % full-scale sine wave [5] Bandwidth (fclk = 40 MHz) B bandwidth - 15 - MHz 75 % full-scale sine wave - 20 - MHz small signal at mid-scale; VI = 10 LSB at code 512 - 350 - MHz ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 7 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz Table 6. Characteristics …continued VCCA = V3 to V4 = 4.75 V to 5.25 V; VCCD = V11 to V12 and V28 to V27 = 4.75 V to 5.25 V; VCCO = V13 to V14 = 3.0 V to 5.25 V; AGND and DGND shorted together; Tamb = 0 C to +70 C; typical values measured at VCCA = VCCD = 5 V and VCCO = 3.3 V; CL = 15 pF and Tamb = 25 C; unless otherwise specified. Symbol Parameter Conditions ts(LH) LOW to HIGH settling time ts(HL) HIGH to LOW settling time full-scale square wave; see Figure 6 [6] Min Typ Max Unit - 1.5 3.0 ns - 1.5 3.0 ns Harmonics (fclk = 40 MHz); see Figure 7 and 8 1H first harmonic level fi = 4.43 MHz - - 0 dB 2H second harmonic level fi = 4.43 MHz - 75 65 dB 3H third harmonic level fi = 4.43 MHz - 72 65 dB THD total harmonic distortion fi = 4.43 MHz - 64 - dB 55 58 - dB fi = 4.43 MHz - 9.4 - bit fi = 7.5 MHz - 9.1 - bit fi = 4.43 MHz - 9.4 - bit fi = 7.5 MHz - 9.0 - bit fi = 10 MHz - 8.9 - bit fi = 15 MHz - 8.1 - bit fi = 4.43 MHz - 9.3 - bit fi = 7.5 MHz - 8.9 - bit fi = 10 MHz - 8.8 - bit fi = 15 MHz - 8.0 - bit fclk = 40 MHz - 69 - dB fclk = 40 MHz; fi = 4.43 MHz; VI = 16 LSB at code 512 - 1013 - times/samples fclk = 40 MHz; PAL modulated ramp - 0.8 - % Signal-to-noise ratio; see Figure 7 and S/N signal-to-noise ratio 8[7] full scale; without harmonics; fclk = 40 MHz; fi = 4.43 MHz Effective bits; see Figure 7 and 8[7] ENOB effective number of bits ADC1004S030TS; fclk = 30 MHz ADC1004S040TS; fclk = 40 MHz ADC1004S050TS; fclk = 50 MHz Two-tone intermodulation[8] IM intermodulation suppression Bit error rate BER bit error rate Differential gain[9] Gdif differential gain ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 8 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz Table 6. Characteristics …continued VCCA = V3 to V4 = 4.75 V to 5.25 V; VCCD = V11 to V12 and V28 to V27 = 4.75 V to 5.25 V; VCCO = V13 to V14 = 3.0 V to 5.25 V; AGND and DGND shorted together; Tamb = 0 C to +70 C; typical values measured at VCCA = VCCD = 5 V and VCCO = 3.3 V; CL = 15 pF and Tamb = 25 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fclk = 40 MHz; PAL-modulated ramp - 0.4 - deg Differential phase [9] dif differential phase Timing (fclk = 40 MHz; CL = 15 pF); see Figure 4[10] td(s) sampling delay time - 3 - ns th(o) output hold time 4 - - ns td(o) output delay time VCCO = 4.75 V - 10 13 ns VCCO = 3.15 V - 12 15 ns CL load capacitance - - 15 pF 3-state output delay times; see Figure 5 tdZH float to active HIGH delay time - 5.5 8.5 ns tdZL float to active LOW delay time - 12 15 ns tdHZ active HIGH to float delay time - 19 24 ns tdLZ active LOW to float delay time - 12 15 ns [1] In addition to a good layout of the digital and analog ground, it is recommended that the rise and fall times of the clock must not be less than 0.5 ns. [2] Analog input voltages producing code 0 up to and including code 1023: a) Voffset BOTTOM is the difference between the analog input which produces data equal to 00 and the reference voltage on pin RB (VRB) at Tamb = 25 C. b) Voffset TOP is the difference between the reference voltage on pin RT (VRT) and the analog input which produces data outputs equal to code 1023 at Tamb = 25 C. [3] In order to ensure the optimum linearity performance of such converter architecture the lower and upper extremities of the converter reference resistor ladder (corresponding to output codes 0 and 1023 respectively) are connected to pins RB and RT via offset resistors ROB and ROT as shown in Figure 3. V RT – V RB R OB + R L + R OT a) The current flowing into the resistor ladder is I = --------------------------------------- and the full-scale input range at the converter, to cover code 0 RL to 1023 is V I = R L I L = --------------------------------------- V RT + V RB = 0.852 V RT – V RB R OB + R L + R OT RL --------------------------------------b) Since RL, ROB and ROT have similar behavior with respect to process and temperature variation, the ratio R OB + R L + R OT will be kept reasonably constant from device to device. Consequently, the variation of the output codes at a given input voltage depends mainly on the difference VRT VRB and its variation with temperature and supply voltage. When several ADCs are connected in parallel and fed with the same reference source, the matching between each of them is optimized. [4] V 1023 – V 0 – V i p – p E G = ------------------------------------------------------- 100 Vi p – p [5] The analog bandwidth is defined as the maximum input sine wave frequency which can be applied to the device. No glitches greater than 2 LSB, neither any significant attenuation are observed in the reconstructed signal. [6] The analog input settling time is the minimum time required for the input signal to be stabilized after a sharp full-scale input (square wave signal) in order to sample the signal and obtain correct output data. ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 9 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz [7] Effective bits are obtained via a Fast Fourier Transform (FFT) treatment taking 8000 acquisition points per equivalent fundamental period. The calculation takes into account all harmonics and noise up to half of the clock frequency (Nyquist frequency). Conversion to signal-to-noise ratio: SINAD = ENOB 6.02 + 1.76 dB. [8] Intermodulation measured relative to either tone with analog input frequencies of 4.43 MHz and 4.53 MHz. The two input signals have the same amplitude and the total amplitude of both signals provides full-scale to the converter. [9] Measurement carried out using video analyzer VM700A, where the video analog signal is reconstructed through a digital-to-analog converter. [10] Output data acquisition: the output data is available after the maximum delay time of td(max). For 50 MHz version Integrated Device Technology recommends the lowest possible output load. RT ROT code 1023 RL RL RM IL RL Rlad RL code 0 ROB RB 014aaa325 Fig 3. Explanation of Table 6, Table note 3 11. Additional information relating to Table 6 Table 7. Output coding and input voltage (typical values; referenced to AGND, VRB = 1.3 V, VRT = 3.67 V) Code Underflow Vi(a)(p-p) (V) < 1.475 IR Binary outputs D9 to D0 Two’s complement outputs D9 to D0 0 00 0000 0000 10 0000 0000 0 1.475 1 00 0000 0000 10 0000 0000 1 - 1 00 0000 0001 10 0000 0001 - 1022 - 1 11 1111 1110 01 1111 1110 1023 3.495 1 11 1111 1111 01 1111 1111 Overflow > 3.495 0 11 1111 1111 01 1111 1111 ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 10 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz Table 8. Mode selection TC OE D9 to D0 IR X 1 high impedance high impedance 0 0 active; two’s complement active 1 0 active; binary active sample N + 1 sample N sample N + 2 tw(clk)L tw(clk)H VCCO CLK 50% 0V sample N sample N + 1 sample N + 2 VI td(s) th(o) VCCO DATA D0 to D9 DATA N−2 DATA N−1 DATA N DATA N+1 50% 0V td(o) Fig 4. Timing diagram ADC1004S030_040_050_4 Product data sheet 014aaa326 © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 11 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz VCCD 50% OE tdHZ tdZH HIGH 90% output data 50% tdLZ LOW tdZL HIGH output data 50% LOW 10% VCCD TEST S1 tdLZ VCCD tdZL VCCD tdHZ DGND tdZH DGND 3.3 kΩ ADC1004S050 S1 15 pF OE 014aaa335 frequency on pin OE = 100 kHz Fig 5. Timing diagram and test conditions of 3-state output delay time ts(LH) ts(HL) code 1023 VI 50% 50% code 0 2 ns CLK 2 ns 50% 50% 0.5 ns 0.5 ns 014aaa327 Fig 6. Analog input settling time diagram ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 12 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz 014aaa328 +20 amplitude (dB) −20 −60 −100 −140 0 5.00 10.0 15.0 20.0 f (MHz) Effective bits: 9.42; THD = 71.8 dB. Harmonic levels (dB): 2nd = 83.19; 3rd = 78.09; 4th = 78.72; 5th = 78.33; 6th = 77.55. Fig 7. Typical fast Fourier transform (fclk = 40 MHz; fi = 4.43 MHz) 014aaa329 +20 amplitude (dB) −20 −60 −100 −140 0 5.0 10.0 15.0 20.0 25.0 f (MHz) Effective bits: 8.91; THD = 62.96 dB. Harmonic levels (dB): 2nd = 71.38; 3rd = 71.54; 4th = 74.14; 5th = 65.15; 6th = 77.16. Fig 8. Typical fast Fourier transform (fclk = 50 MHz; fi = 10 MHz) ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 13 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz VCCA VCCO D9 to D0 IR VI OGND AGND 014aaa330 Fig 9. CMOS data and in-range outputs 014aaa332 Fig 10. Analog inputs VCCA VCCO RT RL RL RM OE TC RL RL RB OGND AGND 014aaa331 014aaa323 Fig 11. OE and TC input Fig 12. RB, RM and RT VCCD 1.5 V CLK DGND 014aaa324 Fig 13. CLK input ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 14 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz 12. Application information CLK TC VCCA (3) 100 nF AGND n.c. RB(1) RM(1) 100 nF 100 nF AGND AGND VI RT(1) OE 100 nF VCCD2 AGND (3) 100 nF DGND2 VCCO (3) 100 nF OGND 1 28 2 27 3 26 4 25 5 24 6 23 7 ADC1004S050 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 VCCD1 DGND1 (3) 100 nF IR D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 n.c.(2) 014aaa338 The analog and digital supplies should be separated and well decoupled A user manual is available that describes the demonstration board that uses the version ADC1004S030/040/050 family with an application environment. (1) RB, RM and RT are decoupled to AGND. (2) Pin 15 may be connected to DGND in order to prevent noise influence. (3) Decoupling capacitor for supplies; must be placed close to the device. Fig 14. Application diagram 12.1 Alternative parts The following alternative parts are also available: Table 9. Alternative parts Type number Description Sampling frequency ADC1003S030 Single 10 bits ADC, with voltage regulator[1] 30 MHz ADC1003S040 Single 10 bits ADC, with voltage regulator[1] 40 MHz ADC1003S050 Single 10 bits ADC, with voltage regulator[1] 50 MHz ADC1005S060 Single 10 bits ADC[1] 60 MHz ADC0804S030 ADC0804S040 ADC0804S050 [1] Single 8 bits ADC[1] 30 MHz Single 8 bits ADC[1] 40 MHz Single 8 bits ADC[1] 50 MHz Pin to pin compatible ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 15 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz 13. Package outline SSOP28: plastic shrink small outline package; 28 leads; body width 5.3 mm D SOT341-1 E A X c HE y v M A Z 28 15 Q A2 A (A 3) A1 pin 1 index θ Lp L 1 14 w M bp e detail X 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HE L Lp Q v w y Z (1) θ mm 2 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 10.4 10.0 5.4 5.2 0.65 7.9 7.6 1.25 1.03 0.63 0.9 0.7 0.2 0.13 0.1 1.1 0.7 8o o 0 Note 1. Plastic or metal protrusions of 0.2 mm maximum per side are not included. OUTLINE VERSION SOT341-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-19 MO-150 Fig 15. Package outline SOT341-1 (SSOP28) ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 16 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz 14. Revision history Table 10. Revision history Document ID Release date Data sheet status Change notice Supersedes ADC1004S030_040_050_4 20120702 Product data sheet - ADC1004S030_040_050_3 ADC1004S030_040_050_3 20080807 Product data sheet - ADC1004S030_040_050_2 Modifications: • • • Corrections made to the table description in Table 1. Corrections made to several entries in Table 6. Corrections made to Figure 12. ADC1004S030_040_050_2 20080616 Product data sheet - ADC1004S030_040_050_1 ADC1004S030_040_050_1 20080611 Product data sheet - - 15. Contact information For more information or sales office addresses, please visit: http://www.idt.com ADC1004S030_040_050_4 Product data sheet © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 17 of 18 ADC1004S030/040/050 Integrated Device Technology Single 10 bits ADC, up to 30 MHz, 40 MHz or 50 MHz 16. Contents 1 2 3 4 5 6 7 7.1 7.2 8 General description . . . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quick reference data . . . . . . . . . . . . . . . . . . . . . Ordering information . . . . . . . . . . . . . . . . . . . . . Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . Pinning information . . . . . . . . . . . . . . . . . . . . . . Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin description . . . . . . . . . . . . . . . . . . . . . . . . . Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 1 2 2 3 4 4 4 5 9 10 11 12 12.1 13 14 15 16 ADC1004S030_040_050_4 Product data sheet Thermal characteristics . . . . . . . . . . . . . . . . . . 5 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 6 Additional information relating to Table 6 . . 10 Application information . . . . . . . . . . . . . . . . . 15 Alternative parts . . . . . . . . . . . . . . . . . . . . . . . 15 Package outline. . . . . . . . . . . . . . . . . . . . . . . . 16 Revision history . . . . . . . . . . . . . . . . . . . . . . . 17 Contact information . . . . . . . . . . . . . . . . . . . . 17 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 © IDT 2012. All rights reserved. Rev. 04 — 2 July 2012 18 of 18