Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Film Type Data Sheet Chip Inductor (Chip Coil) 1 for High Frequency Film Type LQP18M Series (0603 Size) ■ Packaging 0.8±0.15 ■ Dimensions Packaging Minimum Quantity D 180mm Paper Tape 4000 J 330mm Paper Tape 10000 B Bulk(Bag) 500 0.5±0.1 1.6±0.15 Code 0.2 min. (in mm) ■ Rated Value (p: packaging code) Part Number Inductance Test Frequency Rated Current Max. of DC resistance Q (min.) Test Frequency Self Resonance Frequency (min.) LQP18MN1N3C02p 1.3nH±0.2nH 500MHz 300mA 0.3ohm 17 500MHz 6000MHz LQP18MN1N5C02p 1.5nH±0.2nH 500MHz 300mA 0.3ohm 17 500MHz 6000MHz LQP18MN1N8C02p 1.8nH±0.2nH 500MHz 250mA 0.4ohm 17 500MHz 6000MHz LQP18MN2N2C02p 2.2nH±0.2nH 500MHz 250mA 0.4ohm 17 500MHz 6000MHz LQP18MN2N7C02p 2.7nH±0.2nH 500MHz 250mA 0.4ohm 17 500MHz 6000MHz LQP18MN3N3C02p 3.3nH±0.2nH 500MHz 250mA 0.4ohm 17 500MHz 6000MHz LQP18MN3N9C02p 3.9nH±0.2nH 500MHz 200mA 0.5ohm 17 500MHz 5900MHz LQP18MN4N7C02p 4.7nH±0.2nH 500MHz 200mA 0.5ohm 17 500MHz 5200MHz LQP18MN5N6C02p 5.6nH±0.2nH 500MHz 200mA 0.6ohm 17 500MHz 4700MHz LQP18MN6N8C02p 6.8nH±0.2nH 500MHz 200mA 0.7ohm 17 500MHz 4300MHz LQP18MN8N2C02p 8.2nH±0.2nH 500MHz 150mA 0.8ohm 17 500MHz 3600MHz LQP18MN10NG02p 10nH±2% 500MHz 150mA 1.0ohm 17 500MHz 3400MHz LQP18MN12NG02p 12nH±2% 500MHz 150mA 1.0ohm 17 500MHz 3000MHz LQP18MN15NG02p 15nH±2% 500MHz 150mA 1.3ohm 17 500MHz 2700MHz LQP18MN18NG02p 18nH±2% 500MHz 100mA 1.5ohm 17 500MHz 2300MHz LQP18MN22NG02p 22nH±2% 500MHz 100mA 1.9ohm 17 500MHz 2100MHz LQP18MN27NG02p 27nH±2% 500MHz 100mA 2.4ohm 17 500MHz 1900MHz LQP18MN33NG02p 33nH±2% 500MHz 100mA 2.8ohm 17 500MHz 1700MHz LQP18MN39NG02p 39nH±2% 500MHz 100mA 2.8ohm 17 500MHz 1400MHz LQP18MN47NG02p 47nH±2% 300MHz 100mA 2.2ohm 17 300MHz 1200MHz LQP18MN56NG02p 56nH±2% 300MHz 50mA 3.4ohm 17 300MHz 1000MHz LQP18MN68NG02p 68nH±2% 300MHz 50mA 3.5ohm 17 300MHz 900MHz LQP18MN82NG02p 82nH±2% 300MHz 50mA 4.6ohm 17 300MHz 800MHz Operating Temperature Range: -40°C to +85°C Only for reflow soldering. Continued on the following page. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Film Type Data Sheet 2 Continued from the preceding page. Part Number LQP18MNR10G02p Inductance Test Frequency Rated Current 100nH±2% 300MHz 50mA Max. of DC resistance Q (min.) Test Frequency 6.1ohm 17 Self Resonance Frequency (min.) 300MHz 700MHz Operating Temperature Range: -40°C to +85°C Only for reflow soldering. ■ Q-Frequency Characteristics (Typ.) ■ Inductance-Frequency Characteristics (Typ.) 200 1000 100nH 1.5nH 68nH 160 Inductance (nH) 33nH 120 Q 3.3nH 80 15nH 100 6.8nH 10 6.8nH 40 3.3nH 33nH 0 100 100nH 15nH 68nH 1000 Frequency (MHz) 1 100 10000 1.5nH 1000 Frequency (MHz) 10000 ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/