Hermetic Infrared Emitting Diode OP130 Series Features: • • • • • • TO-46 hermetically sealed package Focused and non-focused optical light pattern Enhanced temperature range Mechanically and spectrally matched to other OPTEK devices Choice of power ranges Choice of narrow or wide irradiance pattern “W” Description: Each OP130 series device is a 935 nm gallium arsenide (GaAs) infrared LED mounted in a hermetically sealed TO -46 package that provides an enhanced temperature range with a variety of power ranges The TO-46 housing also offers high power dissipation and superior protection for hostile environments. Each OP130 device has a narrow beam with an inclusive angle at half power points of 18°. Each OP130W series device has a broad irradiance pattern of 50° at half power points, providing relatively even illumination over a large area. These devices are designed to efficiently operate with OP800, OP593, OP598 and OP599 phototransistors or the OP830 photodarlington. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications: • • • • • • Ordering Information Non-contact reflective object sensor Assembly line automation Machine automation Machine safety End of travel sensor Door sensor RoHS Part LED Peak Number Wavelength OP130 OP131 OP132 OP133 OP130W OP131W OP132W OP133W 935 nm Output Power (mW/cm2) Min / Max 1.0 / NA 3.0 / NA 4.0 / NA 5.0 / NA 1.0 / NA 3.0 / NA 4.0 / NA 5.0 / NA Lens Total Beam Type Angle Dome Lead Length (Min) 18° 0.50" Flat 50° OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue B 10/2012 Page 1 of 4 Hermetic Infrared Emitting Diode OP130 Series OP130, OP131, OP132, OP133 Anode Cathode DIMENSIONS ARE IN: [MILLIMETERS] INCHES OP130W, OP131W, OP132W, OP133W Anode Cathode DIMENSIONS ARE IN: [MILLIMETERS] INCHES Pin # LED 1 Anode 2 Cathode OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 10/2012 Page 2 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Hermetic Infrared Emitting Diode OP130 Series Absolute Maximum Ratings (TA=25°C unless otherwise noted) Storage Temperature Range -65o C to +150o C Operating Temperature Range -65o C to +125o C 2.0 V Reverse Voltage Continuous Forward Current 100 mA Peak Forward Current (2 us pulse width, 0.1% duty cycle) 10.0 A Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 260° C(1)(2) Power Dissipation 200 mW(3) Electrical Characteristics (TA = 25°C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS 1.0 3.0 4.0 5.0 - - mW IF = 100 mA(3 ) Input Diode PO Radiant Power Output OP130, OP130W OP131, OP131W OP132, OP132W OP133, OP133W VF Forward Voltage - - 1.75 V IF = 100 mA (3) IR Reverse Current - - 100 µA VR= 2.0 V λP Wavelength at Peak Emission - 935 - nm IF = 10 mA β Spectral Bandwidth between Half Power Points - 50 - nm IF = 10 mA Notes: 1. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. 2. Derate linearly 2.0 mW/° C above 25° C. 3. Measurement made with 100 µs pulse measured at the trailing edge of the pulse with a duty cycle of 0.1% and an IF = 100 mA. Electrical Characteristics (TA = 25°C unless otherwise noted — for reference only) SYMBOL PARAMETER MIN TYP MAX UNITS Spectral Shift with Temperature - +0.30 - nm/°C Emission Angle at Half Power Points OP130 series OP130W series - 18 50 - Degree tr Output Rise Time - 1000 - ns tf Output Fall Time - 500 - ns TEST CONDITIONS Input Diode ∆λP /∆T θHP IF = Constant I F = 100 mA IF(PK)=100 mA, PW=10 µs, and D.C.=10.0% OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com Issue B 10/2012 Page 3 of 4 Hermetic Infrared Emitting Diode OP130 Series OP130 Series (including “W” devices) Forward Voltage vs Forward Current vs Temperature Optical Power vs IF vs Temp 4.0 1.8 Normalized at 20 mA and 20o C 1.7 3.5 -65°C -40°C -20°C +0°C +20°C +40°C +60°C +80°C +100°C +125°C 3.0 Normalized Optical Power Typical Forward Voltage (V) 1.6 1.5 1.4 1.3 -65°C -40°C -20°C +0°C +20°C +40°C +60°C +80°C +100°C +125°C 1.2 1.1 1.0 2.5 2.0 1.5 1.0 0.5 0.9 0.0 0 5 10 15 20 25 30 35 40 45 0 5 10 15 20 25 30 35 40 45 50 Forward Current IF (mA) Forward Current (mA) Distance vs Output Power vs Forward Current 9 Normalized at 0.6" and 50 mA 8 Forward Current Normalized Output Power 7 10 mA 20 mA 30 mA 40 mA 50 mA 60 mA 80 mA 100 mA 6 5 4 3 2 1 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Distance (inches) OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue B 10/2012 Page 4 of 4 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 [email protected] www.optekinc.com