ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 DESCRIPTION 1 8 2 7 These devices belong to Isocom wide body package range optocouplers. 3 6 FEATURES 4 5 The ICPLW137, ICPLW2601 and ICPLW2611 devices each consist of an infrared emitting diode, optically coupled to a high speed integrated photo detector logic gate with a strobable output. • • • • • • • • High Speed 10Mbit/s Wide Body Package 10kV/μs min. Common Mode Transient Immunity (ICPLW2611) High AC Isolation Voltage 5000VRMS Guaranteed Performance from -40°C to +85°C Strobable Logic Gate Output Pb Free and RoHS Compliant Safety Approvals Pending APPLICATIONS • • • • • • • Line Receivers, Data Communication LSTTL to TTL, LSTTL or 5V CMOS Data Multiplexing Pulse Transformer Replacement Switch Mode Power Supplies Ground Loop Elimination Computer Peripheral Interface ORDER INFORMATION • • Add SM after PN for Surface Mount, Add SMT&R after PN for Surface Mount Tape & Reel . ISOCOM COMPONENTS 2004 LTD Unit 25B, Park View Road West, Park View Industrial Estate Hartlepool, Cleveland, TS25 1UD, United Kingdom Tel: +44 (0)1429 863 609 Fax : +44 (0)1429 863 581 e-mail: [email protected] http://www.isocom.com 1 16/02/2016 1. No Connection 2. Anode 3. Cathode 4. No Connection 5. Gnd 6. Vout 7. VE 8. VCC A 0.1μF bypass capacitor must be connected between pins 8 and 5. ABSOLUTE MAXIMUM RATINGS (TA = 25°C) Input Diode Forward Current Reverse Voltage Power dissipation 50mA 5V 100mW Output Output Current Output Voltage Supply Voltage Enable Input Voltage (maximum 500mV above VCC) Power Dissipation 50mA 7.0V 7.0V 5.5V 85mW Total Package Isolation Voltage (R.H. 40 - 60%, 1 min, Pins 1, 2, 3 & 4 shorted together, Pins 5, 6, 7 & 8 shorted together) Operating Temperature Storage Temperature Lead Soldering Temperature (10s) 5000VRMS -40 to +85 °C -55 to +125 °C 260°C ISOCOM COMPONENTS ASIA LTD Hong Kong Office, Block A, 8/F, Wah Hing Industrial mansion, 36 Tai Yau Street, San Po Kong, Kowloon, Hong Kong. Tel: +852 2995 9217 Fax : +852 8161 6292 e-mail: [email protected] DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 Truth Table (Positive Logic) Input Enable Output H H L L H H H L H L L H H NC L L NC H ELECTRICAL CHARACTERISTICS (TA = -40°C to +85°C unless otherwise specified) INPUT Parameter Symbol Test Condition Forward Voltage VF IF = 10mA Reverse Voltage VR IR = 100µA, TA = 25°C ΔVF/ΔTA IF = 10mA -1.9 mV/°C CIN VF = 0V, f = 1MHz 70 pF Symbol Test Condition High Level Supply Current ICCH Low Level Supply Current Temperature Coefficient of Forward Voltage Input Capacitance Min Typ Max Unit 1.4 1.8 V 5.0 V OUTPUT Parameter 2 Typ Max Unit IF = 0mA, VE = 0.5V, VCC = 5.5V 6.5 10 mA ICCL IF = 10mA, VE = 0.5V, VCC = 5.5V 8 13 mA High Level Enable Current IEH VE = 2.0V, VCC = 5.5V -0.6 -1.6 mA Low Level Enable Current IEL VE = 0.5V, VCC = 5.5V -0.8 -1.6 mA High Level Enable Voltage VEH IF = 10mA, VCC = 5.5V Low Level Enable Voltage VEL IF = 10mA, VCC = 5.5V 16/02/2016 Min V 2.0 0.8 DC93192 V ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 ELECTRICAL CHARACTERISTICS (TA = -40°C to +85°C unless otherwise specified) COUPLED Parameter Symbol Test Condition High Level Output Current IOH Low Level Output Voltage Input Threshold Current Min Typ Max Unit VCC = 5.5V, VE = 2.0V, VO = 5.5V, IF = 250μA 2.1 100 μA VOL VCC = 5.5V, VE = 2.0V, IF = 5mA, IOL = 13mA 0.35 0.6 V IFT VCC = 5.5V, VE = 2.0V, VO = 0.6V, IOL = 13mA 3.0 5 mA Switching Characteristics (TA = -40°C to +85°C, VCC = 5V, IF = 7.5mA unless otherwise specified) 3 Parameter Symbol Test Condition Propagation Delay Time to Output High Level tPLH Propagation Delay Time to Output Low level Pulse Width Distortion Typ Max Unit CL = 15pF, RL = 350Ω, TA = 25°C 35 100 ns tPHL CL = 15pF, RL = 350Ω, TA = 25°C 40 100 ns |tPHL-tPLH| CL = 15pF, RL = 350Ω 5 40 ns Output Rise Time tr CL = 15pF, RL = 350Ω 40 ns Output Fall Time tf CL = 15pF, RL = 350Ω 10 ns Enable Propagation Delay Time to Output High Level tELH IF = 7.5mA, VEH = 3.5V, CL = 15pF, RL = 350Ω 15 ns Enable Propagation Delay Time to Output Low Level tEHL IF = 7.5mA, VEH = 3.5V, CL = 15pF, RL = 350Ω 15 ns 16/02/2016 Min DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 ELECTRICAL CHARACTERISTICS (TA = -40°C to +85°C unless otherwise specified) Switching Characteristics (TA = -40°C to +85°C, VCC = 5V, IF = 7.5mA unless otherwise specified) Parameter Common Mode Transient Immunity at Logic High Symbol CMH Test Condition Min ICPLW137 (Fig 14) Typ Max Unit 5000 V/μs 5000 V/μs IF = 0mA, VOH (Min) = 2V, RL = 350Ω, VCM = 10Vp-p, TA = 25°C ICPLW2601 (Fig 14) 5000 IF = 0mA, VOH (Min) = 2V, RL = 350Ω, VCM = 50Vp-p, TA = 25°C ICPLW2611 (Fig 14) 10000 IF = 0mA, VOH (Min) = 2V, RL = 350Ω, VCM = 400Vp-p, TA = 25°C ICPLW2611 (Fig 15) 20000 IF = 0mA, VOH (Min) = 2V, RL = 350Ω, VCM = 400Vp-p, TA = 25°C Common Mode Transient Immunity at Logic Low CML ICPLW137 (Fig 14) IF = 7.5mA, VOL (Max) = 0.8V, RL = 350Ω, VCM = 10Vp-p, TA = 25°C ICPLW2601 (Fig 14) 5000 IF = 7.5mA, VOL (Max) = 0.8V, RL = 350Ω, VCM = 50Vp-p, TA = 25°C ICPLW2611 (Fig 14) 10000 IF = 7.5mA, VOL (Max) = 0.8V, RL = 350Ω, VCM = 400Vp-p, TA = 25°C ICPLW2611 (Fig 15) 20000 IF = 7.5mA, VOL (Max) = 0.8V, RL = 350Ω, VCM = 400Vp-p, TA = 25°C 4 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 5 Fig 1 Forward Current vs Forward Voltage Fig 2 Input Threshold Current vs TA Fig 3 Input Current vs Output Voltage Fig 4 Low Level Output Voltage vs TA Fig 5 Low Level Output Current vs TA Fig 6 High Level Output Current vs TA 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 Fig 7 Propagation Delay Time vs Forward Current Fig 8 Propagation Delay Time vs TA Fig 9 Enable Propagation Delay Time vs TA Fig 10 Pulse Width Distortion vs TA Fig 11 Rise Time / Fall Time vs TA 6 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 IF=7.5mA IF=3.75mA Input £[ tPHL tPLH Output (Vo) 1.5V £[ 90% Output (Vo) 10% Fig 12 tPHL, tPLH, tr and tf Test Circuit tf tr 3.0V 1.5V Input tEHL tELH Output (Vo) 1.5V Fig 13 tEHL and tELH Test Circuit 7 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 Peak VCM 0V 5V VO CMH Switching Pos. A, IF=0mA VO(Min) VO(Max) VO 0.5V Switching Pos. B, IF=7.5mA CML Fig 14 Common Mode Transient Immunity Test Circuit Fig 15 Recommended Drive Circuit for ICPLW2611 for High Common Mode Transient Immunity CMH : Common mode transient immunity in logic high level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode pulse signal VCM, to assure that the output will remain in a logic high state (i.e., VO > 2.0V). CML : Common mode transient immunity in logic low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a logic low state (i.e., VO < 0.8V). 8 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 NOTES : - The VCC supply must be bypassed by a 0.1μF capacitor or larger with good high frequency characteristic and should be connected as close as possible to the package VCC and GND pins. - Enable Input – No pull up resistor required as the device has an internal pull up resistor. - tPLH is measured from the 3.75mA level on the HIGH to LOW transition of the input current pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse. - tPHL is measured from the 3.75mA level on the LOW to HIGH transition of the input current pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse. - tr Rise time is measured from the 10% to the 90% levels on the LOW to HIGH transition of the output pulse. - tf Fall time is measured from the 90% to the 10% levels on the HIGH to LOW transition of the output pulse. - tELH is measured from the 1.5V level on the HIGH to LOW transition of the input Enable voltage pulse to the 1.5V level on the LOW to HIGH transition of the output voltage pulse. - tEHL is measured from the 1.5V level on the LOW to HIGH transition of the input Enable voltage pulse to the 1.5V level on the HIGH to LOW transition of the output voltage pulse. - CMH– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the HIGH state (i.e., VO > 2.0V). - CML– The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the LOW state (i.e., VO < 0.8V). 9 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 ORDER INFORMATION ICPLW137, ICPLW2601, ICPLW2611 After PN PN Description Packing quantity None ICPLW137, ICPLW2601, ICPLW2611 Standard DIP 40 pcs per tube SM ICPLW137SMT&R, ICPLW2601SMT&R, ICPLW2611SMT&R Surface Mount Tape and Reel 500 pcs per reel DEVICE MARKING ICPLW137 I YWW ICPLW137 Y WW I 10 16/02/2016 denotes Device Part Number (ICPLW137 is used as example) denotes 1 digit Year code denotes 2 digit Week code denotes Isocom DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 PACKAGE DIMENSIONS (mm) DIP SMD 11 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 RECOMMENDED PAD LAYOUT FOR SMD (mm) 12 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 IR REFLOW SOLDERING TEMPERATURE PROFILE (One Time Reflow Soldering is Recommended) TP 260°C TP - 5°C Max Ramp Up Rate 3°C/s TEMP (°C) TL Tsmax Tsmin tP Max Ramp Down Rate 6°C/s 217°C TL 200°C 150°C ts Preheat 60s – 120s 25°C TIME (s) Time 25°C to Peak Temperature Profile Details 13 Conditions Preheat - Min Temperature (TSMIN) - Max Temperature (TSMAX) - Time TSMIN to TSMAX (ts) 150°C 200°C 60s - 120s Soldering Zone - Peak Temperature (TP) - Liquidous Temperature (TL) - Time within 5°C of Actual Peak Temperature (TP ̶ 5°C) - Time maintained above TL (tL) - Ramp Up Rate (TL to TP) - Ramp Down Rate (TP to TL) 260°C 217°C 30s 60s - 100s 3°C/s max 6°C/s max Average Ramp Up Rate (Tsmax to TP) 3°C/s max Time 25°C to Peak Temperature 8 minutes max 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 TAPE AND REEL PACKAGING Direction of feed from reel 14 Dimension No. A B Do D1 E F Dimension( mm) 12.7±0.1 11.45±0.1 1.5±0.1 1.5±0.1 1.75±0.1 11.5±0.1 Dimension No. Po P1 P2 t W K Dimension (mm) 4.0±0.1 16.0±0.1 2.0±0.1 0.4±0.05 24.00±0.3 4.6±0.1 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 NOTES : - Isocom is continually improving the quality, reliability, function or design and Isocom reserves the right to make changes without further notices. - The products shown in this publication are designed for the general use in electronic applications such as office automation equipment, communications devices, audio/visual equipment, electrical application and instrumentation. - For equipment/application where high reliability or safety is required, such as space applications, nuclear power control equipment, medical equipment, etc., please contact our sales representatives. - When requiring a device for any ”specific” application, please contact our sales for advice. - The contents described herein are subject to change without prior notice. - Do not immerse device body in solder paste. 15 16/02/2016 DC93192 ISOCOM COMPONENTS ICPLW137, ICPLW2601, ICPLW2611 ISOCOM is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing ISOCOM products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such ISOCOM products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that ISOCOM products are used within specified operating ranges as set forth in the most recent ISOCOM products specifications. __ The ISOCOM products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These ISOCOM products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation Instruments, traffic signal instruments, combustion control instruments, medical Instruments, all types of safety devices, etc.. Unintended Usage of ISOCOM products listed in this document shall be made at the customer’s own risk. __ Gallium arsenide (GaAs) is a substance used in the products described in this document. GaAs dust and fumes are toxic. Do not break, cut or pulverize the product, or use chemicals to dissolve them. When disposing of the products, follow the appropriate regulations. Do not dispose of the products with other industrial waste or with domestic garbage. __ The products described in this document are subject to the foreign exchange and foreign trade laws. __ The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by ISOCOM Components for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of ISOCOM Components or others. __ The information contained herein is subject to change without notice. 16 16/02/2016 DC93192