Fujitsu FTP-632MCL002 24v drive interface board (parallel) Datasheet

24V DRIVE INTERFACE BOARD (PARALLEL)
FTP-622DCL001/011/ FTP-622DSL001/011/012
FOR FTP-622/632/642MCL001/002/301/302/303/304
■ INTERFACE
1. Centronics
(1) Connector (CN1)
Connector part number
: FCN-605Q030-G/S (Fujitsu Components)
Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent
(2) Connector pin assignment
No.
Signal
I/O
Contents
No.
Signal
I/O
Contents
1
PRSTB
I
Data strobe
2
PRSTB-RET
—
Connected to logic GND
3
PRDT0
I
Data 0
4
PRDT0-RET
—
Connected to logic GND
5
PRDT1
I
Data 1
6
PRDT1-RET
—
Connected to logic GND
7
PRDT2
I
Data 2
8
PRDT2-RET
—
Connected to logic GND
9
PRDT3
I
Data 3
10
PRDT3-RET
—
Connected to logic GND
11
PRDT4
I
Data 4
12
PRDT4-RET
—
Connected to logic GND
13
PRDT5
I
Data 5
14
PRDT5-RET
—
Connected to logic GND
15
PRDT6
I
Data 6
16
PRDT6-RET
—
Connected to logic GND
17
PRDT7
I
Data 7
18
PRDT7-RET
—
Connected to logic GND
19
ACKNLG
O
Data input acknowledge
20
ACKNLG-RET
—
Connected to logic GND
21
BUSY
O
Busy
22
BUSY-RET
—
Connected to logic GND
23
RINF2
O
Printer status
24
INPRM-RET
—
Connected to logic GND
25
SLCTIN
I
Printer select
26
INPRM
I
Reset
27
RINF1
O
Printer status
28
RINF3
O
Printer status
29
ATF
I
Paper feed request
30
GND
—
Logic GND
Notes:
• Symbol “——” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
(4) Data input signal timing
(3) Connector pin number
PRDT0~7
t1
FCN-605Q030-G/S (Fujitsu Components) or
equivalent
No.1
t3
PRSTB
t2
BUSY
t4
ACKNLG
No.30
t5
No.2
Data set time :t1≥0.5 µsec
PRSTB pulse :t2≥0.5 µsec
Data hold time :t3≥0.5 µsec
1
PRSTB to BUSY= “H” :t4≤0.5 µsec
.
ACKNLG pulse
:t5=5.0
µsec
.
FTP-622DCL/DSL
Product
Part Number
Function
FTP-622DCL001
Standard (without cutter)
FTP-622DCL011
With cutter control
FTP-622DSL001
Standard (without cutter)
FTP-622DSL011
With cutter controller
FTP-622DSL012
With cutter controller + FLASH ROM
FTP-622DSL112
With Cutter + KANJI+FLASH ROM
Parallel Interface Board
Serial Interface Board
■ SPECIFICATION
Item
Specification
Data receive speed
19200, 9600, 4800, 1200 bps (set by dip switch)
Synchronous method
Asynchronous, full duplex
Hand shake
DTR/DSR signal or XON/XOFF
Input output level
RS232C
Signal level
Space (logic = 0)
Mark (logic = 0)
+3 V ~ +12 V
–3 V ~ –12 V
2. SERIAL INTERFACE (RS232C)
(1) Connector (CN2)
Part number
: B6B-XH-A (J.S.T)
Mating connector part number : XHP-6 (J.S.T) or equivalent
(2) Pin assignment
No.
Signal
I/O
Contents
No.
Signal
I/O
Contents
1
FG
—
Frame GND
2
RD
I
Receive data
3
TD
O
Transmission Data
4
DTR
O
Data terminal ready
5
GND
—
Signal GND
6
DSR
I
Data set ready
Notes: “I” or “O” means a signal direction from the interface board side.
(3) Pin number
B6B-XH-A (J.S.T)
CN2
CN1
6
1
2
FTP-622DCL/DSL
■ CONNECTOR PIN ASSIGNMENT
1. Connector for power supply (CN10)
Part number
: B6P-VH (J.S.T)
Mating connector part number : VHR-6N (J.S.T) or equivalent
No.
Signal
I/O
Contents
No.
Signal
I/O
Contents
1
VCC
—
Power supply for logic (+5 V)
2
GND
—
GND (5 V, 24 V common)
3
GND
—
GND (5 V, 24 V common)
4
GND
—
GND (5 V, 24 V common)
5
VDD
—
Power for head/motor (+24 V)
6
V DD
—
Power for head/motor (+24 V)
2. Connector for thermal head drive (CN8)
Part number
: B16B-PH-K-S (J.S.T)
Mating connector part number : PHR-16 (J.S.T) or equivalent
No.
Signal
I/O
Contents
No.
Signal
I/O
Contents
1
VDH
O
Power for head (+24 V)
2
VDH
O
Power for head (+24 V)
3
GND (VDH)
—
Head GND
4
GND (VDH)
—
Head GND
5
STB1
O
Print enable signal 1
6
STB2
O
Print enable signal 2
7
STB3
O
Print enable signal 3
8
TMP
I
Temperature detection signal
9
STB4
O
Print enable signal 4
10
LAT
O
Print data latch signal
11
STB5
O
Print enable signal 5
12
5 VH
O
Power for logic (+5 V)
13
HCLK
O
Data transmission clock
14
HD
O
Print data output signal
15
GND (VDH)
—
Head GND
16
VDH
O
Power for head (+24 V)
Notes:
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface board side.
3. Connector for Sensor (CN3)
Part number
No.
Signal
: B5B-PH-K-S (J.S.T)
I/O
Contents
No.
Signal
I/O
1
+5 V
—
Power for logic (+5 V)
2
PES
I
3
GND (5 V)
—
Logic GND
4
+5 V
—
5
HUP
I
Contents
Paper end detect signal
Power for logic (+5 V)
Head-up detect signal
3
FTP-622DCL/DSL
7. Connector for control signal input/ output (CN1)
Part number
Mating connector
No.
Signal
: FCN-605Q030-G/S (Fujitsu Components)
: FCN-607B030-G/D (Fujitsu Components) or equivalent
I/O
Contents
No.
Signal
I/O
Contents
1
NC
—
No connection
2
NC
—
No connection
3
NC
—
No connection
4
NC
—
No connection
5
NC
—
No connection
6
NC
—
No connection
7
NC
—
No connection
8
NC
—
No connection
9
NC
—
No connection
10
NC
—
No connection
11
NC
—
No connection
12
NC
—
No connection
13
NC
—
No connection
14
NC
—
No connection
15
NC
—
No connection
16
NC
—
No connection
17
NC
—
No connection
18
NC
—
No connection
19
NC
—
No connection
20
NC
—
No connection
21
NC
—
No connection
22
NC
—
No connection
23
NC
—
No connection
24
NC
—
No connection
25
SLCTIN
Select signal
26
INPRM
27
NC
—
No connection
28
NC
—
No connection
29
ATF
I
Paper feed request
30
GND
—
GND
I
I
Reset signal
*Do not connect outside signal to NC.
4
FTP-622DCL/DSL
4. Connector for paper near end detection (CN5)
Part number
: B2B-PH-K-S (J.S.T)
Mating connector part number : PHR-2 (J.S.T) or equivalent
No.
1
Signal
+5 V
I/O
—
Contents
Power for logic (+5 V)
No.
2
Signal
NES
I/O
I
Contents
Paper near end detect signal
5. Connector for stepping motor drive (CN13)
Part number
No.
Signal
: B4B-PH-K-S (J.S.T)
I/O
Contents
No.
Signal
I/O
Contents
1
MT/B
O
Stepping motor coil excitation
2
MT/B
O
Stepping motor coil excitation
3
MT/A
O
Stepping motor coil excitation
4
MT/A
O
Stepping motor coil excitation
6. Connector for cutter drive (CN11) *1
Part number
No.
Signal
: B4B-EH (J.S.T)
I/O
Contents
No.
Signal
I/O
Contents
1
SW1
I
Cutter position detect signal
2
GND
—
Logic ground
3
M+
O
Motor control signal (+)
4
M-
O
Motor control signal (-)
*1: Only for FTP-622DCL011/111.
5
FTP-622DCL/DSL
■ PRINTING COMMANDS (CENTRONICS INTERFACE)
Command
Contents
HT
Moves the print position to the next tab.
LF
Line feed.
FF
Feeds forms (new page).
ESC RS
Sets reverse printing.
ESC US
Resets reverse printing.
ESC ! +n
Sets print mode.
ESC* +m+n1+n2+d1~dN
Sets the bit image mode “m” for n1, n2 dot numbers.
ESC 2
Sets 1/6 inch line feed length.
ESC 3 + n
Sets the line feed length.
ESC @
Printer initialization.
ESC A+n
Sets the space between lines.
ESC C+n
Sets the page length by character line.
ESC D+d1~dN+NUL
Sets the tab position.
ESC J+n
Feeds paper in forward direction.
ESC K+n
Feeds paper in reverse direction.
ESC c+1+n
Sets the internal processing.
ESC R+n
Selects the international character.
ESC s+n
Sets the printing speed.
ESC d+n
Printing and n-line feeding.
ESC e+n
Reverse line feed in “n” lines after printing.
ESC t+n
Character code table selection.
ESC {+n
Sets/resets the upside down printing.
ECS EM+n
Automatic paper feed distance setting.
ESC X+n+m
Setting turning time of the motor excitation.
ESC V+n
Right Rotation 90° specification / cancellation.
ESC %+n
Selects the font to download*3.
ESC &+y+c1+c2+x+d1~dn
Registers the download front*3.
ESC ?+n
External character registration deletion*3.
FS E+n
Correction of impressed energy.
FS ! +n
Sets the Kanji print mode*1.
FS &
Sets Kanji mode*1.
(Continued)
6
FTP-622DCL/DSL
(Continued)
Command
Contents
FS .
Resets Kanji mode*1.
FS C+n
Selects Kanji code type*1.
FS 9+n
Sets the detection functions.
FS*+m+n1+n2+d1~dn
Prints image data on SRAM*3.
FS r+n
Notifies of printing finish*4.
FS W+n
Sets/resets 4 times enlarged character.
GS <
Line feeds to the next mark.
GS A+m+n
Sets the line feed length after mark detection.
GS E+n
Sets print quality.
GS V+n+m
Executes paper cutting*2.
GS e+n+m
Sets the bar width.
GS h+n
Sets the barcode height.
GS k+m+n+d1~dN
Selects the barcode type and prints.
GS w+n
Sets the barcode length.
GS &+m+x+y1+y2+[d]k
Registration of image data*3.
GS '+m+n
Prints registered image data *3.
GS a+n
Sets and cancels status transmission (valid only for DSL)*3.
*1: Only for FTP-622DSL112.
*2: Only for FTP-622DCL011 or FTP-622DSL011/012.
*3: Only for FTP-622DSL012.
*4: Only for FTP-622DSL011/012.
7
FTP-622DCL/DSL
■ OPTIONS
1. Cable (With FTP-622MCL, FTP-632MCL, FTP-642MCL)
Name
Part Number
Cable Length
FTP-622Y001
270 mm (10.6 inches)
Centronics (CN1)
FTP-622Y201
500 mm (19.71 inches)
Serial (CN2)
FTP-622Y301
500 mm (19.71 inches)
Power cable for head, motor, and logic (CN10)
FTP-622Y401
300 mm (11.8 inches)
* short cable option
FTP-624Y001
150 mm (5.9 inches)
Thermal head connection cable (CN8)*
Interface cable
2. Paper holder
Name
Part number
Flange
FTP-040HF
Stand
FTP-040HS
Fujitsu Components
International
Headquarter
Offices
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Web: www.fcl.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Web: www.fceu.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: [email protected]
Web: www.fcai.fujitsu.com
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: [email protected]
www.fcal.fujitsu.com
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 11/15/2004.
8
Similar pages