MBRF1035CT - MBRF10150CT Isolated 10.0 AMPS. Schottky Barrier Rectifiers ITO - 220AB 4.5± 0.2 10.2± 0.2 3.1+0.2 -0.1 4.0± 0.3 2.6± 0.2 1.4± 0.1 0.6± 0.1 Mechanical Data ? 3.2± 0.2 PIN 2 3 8.2± 0.2 1 16.5± 0.3 15.0± 0.5 Plastic material used carries Underwriters Laboratory Classifications 94V-0 Metal silicon junction, majority carrier conduction Low power loss, high efficiency High current capability, low forward voltage drop High surge capability For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications Guardring for overvoltage protection High temperature soldering guaranteed: 260oC/10 seconds,0.25”(6.35mm)from case 13.5± 0.5 φ 3.3± 0.1 Features Cases: ITO-220AB molded plastic Terminals: Pure tin plated, lead free. solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting position: Any Mounting torque: 5 in. - lbs. max Weight: 0.08 ounce, 2.24 grams 2.6± 0.15 0.6± 0.1 Dimensions in millimeters Maximum Ratings and Electrical Characteristics o Rating at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol MBRF MBRF MBRF MBRF MBRF MBRF MBRF Units Type Number 1035 CT 35 24 35 1045 CT 45 31 45 1050 CT 50 35 50 1060 CT 60 42 60 1090 10100 10150 CT CT CT 90 100 150 63 70 105 90 100 150 Maximum Recurrent Peak Reverse Voltage VRRM Maximum RMS Voltage VRMS Maximum DC Blocking Voltage VDC Maximum oAverage Forward Rectified Current I(AV) 10 at TC=133 C Peak Repetitive Forward Current o(Rated VR, IFRM 10.0 Square Wave, 20KHz) at Tc=133 C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated IFSM 120 Load (JEDEC method ) Peak Repetitive Reverse Surge Current IRRM 0.5 (Note 1) Maximum Instantaneous Forward Voltage at 0.88 0.85 0.80 (Note 2) IF= 5A, Tc=25oC 0.70 0.78 0.75 0.65 IF= 5A, Tc=125oC 0.57 VF o 0.98 0.95 0.90 0.80 IF=10A, Tc=25 C o 0.88 0.85 0.75 0.67 IF=10A, Tc=125 C Maximum Instantaneous Reverse Current o 0.1 IR at Rated DC Blocking Voltage @Tc=25 C 0.1 @ Tc=125 oC 5.0 15 10 Voltage Rate of Change, (Rated VR) dV/dt 10,000 RMS Isolation oVoltage (t=1.0 second, R.H. ≦30%, TA=25 C) 4500 (Note 4) VISO 3500 (Note 5) 1500 (Note 6) Typical Thermal Resistance Per Leg (Note3) RθJC 3.5 Operating Junction Temperature Range TJ -65 to +150 Storage Temperature Range TSTG -65 to +150 1. 2.0 us Pulse Width, f=1.0 KHz 2. Pulse Test: 300us Pulse Width, 1% Duty Cycle Notes: 3. Thermal Resistance from Junction to Case Per Leg. 4. Clip Mounting (on case), where lead does not overlap heatsink with 0.110” offset. 5. Clip mounting (on case), where leads do overlap heatsink. 6. Screw mounting with 4-40 screw, where washer diameter is ≦ < 4.9 mm (0.19”) = http://www.luguang.cn - 116 - mail:[email protected] V V V A A A A V mA mA V/uS V o C/W o C o C MBRF1035CT - MBRF10150CT FIG.1- FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 180 RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 12 10 8 6 4 2 0 0 100 50 100 o CASE TEMPERATURE. ( C) Tj=Tj max. 8.3ms Single Half Sine-Wave JEDEC Method 150 120 90 60 30 0 150 1 10 100 NUMBER OF CYCLES AT 60Hz FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4- TYPICAL REVERSE CHARACTERISTICS 50 MBRF1035CT-1045CT 10 INSTANTANEOUS REVERSE CURRENT. (mA) INSTANTANEOUS FORWARD CURRENT. (A) 40 20 MBRF1050CT-1060CT 10 4 2 1 MBRF1090CT-10100CT Tj=125 0C 1 Tj=75 0C 0.1 0.01 0.4 Tj=25 0C 0 0.2 MBRF10150CT 0.1 0.6 0.7 0.8 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 1.1 0.9 1.0 FORWARD VOLTAGE. (V) 1.2 1.3 0.001 0 60 80 100 120 140 100 TRANSIENT THERMAL IMPEDANCE. ( OC/W) JUNCTION CAPACITANCE.(pF) 40 FIG.6- TYPICAL TRANSIENT THERMAL CHARACTERISTICS PER LEG FIG.5- TYPICAL JUNCTION CAPACITANCE 5,000 0 Tj=25C f=1.0MHz Vsig=50mVp-p 1,000 500 100 0.1 20 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 1 10 REVERSE VOLTAGE. (V) http://www.luguang.cn 100 10 1 0.1 0.01 0.1 1 10 T, PULSE DURATION. (sec) mail:[email protected] 100