NB3N5573 3.3V, Crystal - To- HCSL Clock Generator Description The NB3N5573 is a high precision, low phase noise clock generator that supports PCI Express and Ethernet requirements. The device takes a 25 MHz fundamental mode parallel resonant crystal and generates differential HCSL output at 25 MHz, 100 MHz, 125 MHz or 200 MHz clock frequencies. This device is housed in 5.0 mm x 4.4 mm narrow body TSSOP 16 pin package. http://onsemi.com MARKING DIAGRAM 16 Features 1 TSSOP-16 DT SUFFIX CASE 948F •Uses 25 MHz Fundamental Mode Parallel Resonant Crystal •External Loop Filter is Not Required •HCSL Differential Output •Phase Noise: Offset Noise Power 100 Hz -103 dBc/Hz 1 kHz -1 18 dBc/Hz 10 kHz -122 dBc/Hz 100 kHz -130 dBc/Hz 1 MHz -132 dBc/Hz 10 MHz -149 dBc/Hz •Typical Period Jitter RMS of 1.5 ps •Operating Range 3.3 V ±10% •Industrial Temperature Range -40°C to +85°C •These are Pb-Free Devices 16 A L Y W G 1 NB3N 5573 ALYWG G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. VDD X1/CLK 25 MHz Clock or Crystal Clock Buffer Crystal Oscillator CLK0 Charge Pump Phase Detector HSCL Output VCO X2 HSCL Output BN CLK0 CLK1 CLK1 GND S0 S1 OE IREF Figure 1. NB3N5573 Simplified Logic Diagram © Semiconductor Components Industries, LLC, 2007 August, 2007 - Rev. 1 1 Publication Order Number: NB3N5573/D NB3N5573 S0 1 16 VDD S1 2 15 CLK0 NC 3 14 X1/CLK 4 13 GND X2 5 12 VDD OE 6 11 CLK1 GND 7 10 NC 8 9 CLK0 CLK1 IREF Figure 2. Pin Configuration (Top View) Table 1. PIN DESCRIPTION Pin Symbol I/O 1 S0 Input LVTTL/LVCMOS frequency select input 0. Internal pullup resistor to VDD. See output select table 2 for details. Description 2 S1 Input LVTTL/LVCMOS frequency select input 1. Internal pullup resistor to VDD. See output select Table 2 for details. 12, 16 VDD Power Supply 4 X1/CLK Input Crystal or Clock input. Connect to 25 MHz crystal source or single-ended clock. 5 X2 Input Crystal input. Connect to a 25 MHz crystal or leave unconnected for clock input. Output enable tri-states output when connected to GND. Internal pullup resistor to VDD. 6 OE Input 7, 13 GND Power Supply 9 IREF Output Positive supply voltage pins are connected to +3.3 V supply voltage. Ground 0 V. These pins provide GND return path for the devices. Output current reference pin. Precision resistor (typ. 475 W) is connected to set the output current. 11 CLK1 HCSL Output Noninverted clock output. 10 CLK1 HCSL Output Inverted clock output. 15 CLK0 HCSL Output Noninverted clock output. 14 CLK0 HCSL Output Inverted clock output. 3, 8 NC Do not connect Table 2. OUTPUT FREQUENCY SELECT TABLE S1 S0 fCLKout (MHz) L L 25 L H 100 H L 125 H H 200 Recommended Crystal Parameters Crystal Frequency Load Capacitance Shunt Capacitance, C0 Equivalent Series Resistance Initial Accuracy at 25 °C Temperature Stability Aging C0/C1 Ration Fundamental AT-Cut 25 MHz 16-20 pF 7 pF Max 35 W Max ±20 ppm ±30 ppm ±20 ppm 250 Max http://onsemi.com 2 NB3N5573 Table 3. ATTRIBUTES Characteristic ESD Protection Value Human Body Model > 2 kV Moisture Sensitivity, Indefinite Time Out of Dray Pack (Note 1) Flammability Rating Level 1 Oxygen Index: 28 to 34 UL 94 V-0 @ 0.125 in Transistor Count 7623 Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. Table 4. MAXIMUM RATINGS (Note 2) Symbol Parameter Condition 1 Condition 2 Rating Units 4.6 V -0.5 V to VDD+0.5 V V VDD Positive Power Supply GND = 0 V VI Input Voltage (VIN) GND = 0 V TA Operating Temperature Range -40 to +85 °C Tstg Storage Temperature Range -65 to +150 °C qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm TSSOP–16 TSSOP–16 138 108 °C/W °C/W qJC Thermal Resistance (Junction-to-Case) (Note 3) TSSOP-16 33 to 36 °C/W Tsol Wave Solder 265 °C GND v VI v VDD Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 2. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and not valid simultaneously. If stress limits are exceeded device functional operation is not implied, damage may occur and reliability may be affected. 3. JEDEC standard multilayer board - 2S2P (2 signal, 2 power). Table 5. DC CHARACTERISTICS (VDD = 3.3 V ±10%, GND = 0 V, TA = -40°C to +85°C, Note 4) Symbol Characteristic Min Typ Max Unit 2.97 3.3 3.63 V 120 135 mA 65 mA 2000 VDD + 300 mV GND - 300 800 mV 700 850 mV 0 150 mV 550 mV 150 mV VDD Power Supply Voltage IDD Power Supply Current IDDOE Power Supply Current when OE is Set Low VIH Input HIGH Voltage (X/CLK, S0, S1, and OE) VIL Input LOW Voltage (X/CLK, S0, S1, and OE) VOH Output HIGH Voltage for HCSL Output (See Figure 4) 660 VOL Output LOW Voltage for HCSL Output (See Figure 4) -150 Vcross Crossing Voltage Magnitude (Absolute) for HCSL Output 250 DVcross Change in Magnitude of Vcross for HCSL Output NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 4. Measurement taken with outputs terminated with RS = 33.2 W, RL = 49.9 W, with test load capacitance of 2 pF and current biasing resistor set at 475 W. See Figure 3. http://onsemi.com 3 NB3N5573 Table 6. AC CHARACTERISTICS (VDD = 3.3 V ±10%, GND = 0 V, TA = -40°C to +85°C; Note 5) Characteristic Symbol fCLKIN Clock/Crystal Input Frequency fCLKOUT Output Clock Frequency WNOISE Phase-Noise Performance Tjitter Min Typ Max 25 25 Unit MHz 200 MHz dBc/Hz fCLKout = 200 MHz @ 100 Hz offset from carrier -103 @ 1 kHz offset from carrier -1 18 @ 10 kHz offset from carrier -122 @ 100 kHz offset from carrier -130 @ 1 MHz offset from carrier -132 @ 10 MHz offset from carrier -149 Period Jitter Peak-to-Peak (Note 6) fCLKout = 200 MHz 10 20 ps Period Jitter RMS (Note 6) fCLKout = 200 MHz 1.5 3 Cycle-Cycle RMS Jiter (Note 7) fCLKout = 200 MHz 2 5 Cycle-to-Cycle Peak to Peak Jitter (Note 7) fCLKout = 200 MHz 20 35 ps 1 ms OE Output Enable/Disable Time tDUTY_CYCLE Output Clock Duty Cycle (Measured at cross point) 45 50 55 % tR Output Risetime (Measured from 175 mV to 525 mV, Figure 4) 175 340 700 ps tF Output Falltime (Measured from 525 mV to 175 mV, Figure 4) 175 340 700 ps DtR Output Risetime Variation (Single-Ended) 125 ps DtF Output Falltime Variation (Single-Ended) 125 ps Stabilization Time Stabilization Time From Powerup VDD = 3.3 V 3.0 ms NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. Measurement taken from differential output on single-ended channel terminated with RS = 33.2 W, RL = 49.9 W, with test load capacitance of 2 pF and current biasing resistor set at 475 W. See Figure 3. 6. Sampled with 10000 cycles. 7. Sampled with 1000 cycles. CLK0 RL = 33.2 W Zo = 50 W RL = 33.2 W Zo = 50 W CLK0 RL = 49.9 W RL = 49.9 W HCSL Driver Receiver CLK1 RL = 33.2 W Zo = 50 W RL = 33.2 W CLK2 Zo = 50 W RL = 49.9 W RL = 49.9 W Figure 3. Typical Termination for Output Driver and Device Evaluation http://onsemi.com 4 NB3N5573 700 mV 525 mV 525 mV 175 mV 175 mV 0 mV tR 340 ps 340 ps tF Figure 4. HCSL Output Parameter Characteristics ORDERING INFORMATION Package Shipping† NB3N5573DTG TSSOP-16 (Pb-Free) 96 Units / Rail NB3N5573DTR2G TSSOP-16 (Pb-Free) 2500 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 5 NB3N5573 PACKAGE DIMENSIONS TSSOP-16 CASE 948F-01 ISSUE B 16X K REF 0.10 (0.004) 0.15 (0.006) T U T U M S V S S K ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ K1 2X L/2 16 9 J1 SECTION N-N B -U- L J PIN 1 IDENT. N 0.25 (0.010) 8 1 M 0.15 (0.006) T U S A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. N DIM A B C D F G H J J1 K K1 L M F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE H D DETAIL E G MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ SOLDERING FOOTPRINT* 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 6 INCHES MIN MAX 0.193 0.200 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ NB3N5573 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 7 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NB3N5573/D